Randy Mackay
214a859e97
Copter: remove unused RADX100 definition
...
The real purpose of this small change is to kick off the autobuilder for
the AC3.1.1 release.
2014-01-26 13:41:14 +09:00
Randy Mackay
3ba5b70736
Copter: fix compiler warning from motorsync test
2014-01-26 11:08:34 +09:00
Randy Mackay
a45b9cbe9a
Copter: remove unused RELAY_TOGGLE definition
2014-01-26 10:10:02 +09:00
Stefan
a6b6d46a30
Copter: Update ReleaseNotes.txt
2014-01-22 15:05:31 +09:00
Ju1ien
311bba1419
Copter: landing_complete stays true until thr is raised
...
The idea of the fix is we can't leave land while throttle is 0 and then
we ignore the baro and it's disturbances.
2014-01-22 14:38:35 +09:00
Randy Mackay
7fcd847f77
Copter: reword FRAME parameter's @Value
2014-01-22 11:35:35 +09:00
Randy Mackay
231e3ccaac
Copter: add NewX @Value for FRAME parameter
2014-01-22 10:57:17 +09:00
Randy Mackay
dee5fb212a
Copter: remove dup definition of FRAME_ORIENTATION
...
Ideally the frame orientation parameter should be moved to the motors
class
2014-01-21 21:44:17 +09:00
Randy Mackay
f7f8691ca3
Copter: remove frame setup through CLI
2014-01-21 21:42:59 +09:00
Randy Mackay
34f14a7c13
Copter: version to AC3.1.1-rc2
...
This update applies to pixhawk only
2014-01-21 21:23:11 +09:00
Randy Mackay
3c7e7db8a7
Copter: AC3.1.1-rc2 release notes
2014-01-21 21:22:42 +09:00
Andrew Tridgell
e8b8cc1a5d
Copter: converted to AP_ServoRelayEvents
2014-01-20 17:06:29 +11:00
Andrew Tridgell
e3804e2846
Copter: fixes for AP_Relay API change
2014-01-20 17:06:29 +11:00
Andrew Tridgell
50a90a1043
Copter: enable AP_BoardConfig
2014-01-20 17:06:28 +11:00
Randy Mackay
111d0854a7
Copter: motorsync cli test
2014-01-18 17:00:43 +09:00
Randy Mackay
0f957bdc5a
Copter: lean angle arming check
2014-01-17 17:31:28 +09:00
Randy Mackay
a7f03619f2
Copter: add inav vs baro arming check
...
In-flight Barometer sanity checking will be a more complete solution but
until then this should catch some bad pre-flight barometer behaviour
2014-01-17 17:21:42 +09:00
Andrew Chapman
b7eab7ea22
Copter: Added GCS feedback for save_trim()
...
Trim save gives no feedback, so I've added a gcs_send_text() call to
print "Trim saved" so the user knows to re-center trims again
2014-01-16 14:23:19 +09:00
Randy Mackay
8a29d63d89
Copter: faster baro calibration when arming
...
using update_calibration() instead of the full calibrate() cuts
1.5seconds of the arming time
2014-01-15 23:28:24 +09:00
Randy Mackay
ae4f368f16
Copter: allow ch6 tuning of loiter speed
2014-01-15 15:22:52 +09:00
Randy Mackay
6d55895d30
Copter: simplify do-set-servo mission command
...
This potentially changes the servo number that must be supplied if using
an APM1 but it now shares the same logic as arduplane and also adds
protection that the servo is not attached to the motor.
removed debug message from previous commit.
2014-01-15 14:36:50 +09:00
Randy Mackay
67c2bc7d0b
Copter: add support for MAV_CMD_DO_SET_SERVO
2014-01-15 14:03:04 +09:00
Randy Mackay
a9f1a2ee5e
Copter: disarm on land even if pilot throttle not zero
...
default behaviour remains as before, this is an compile time option only
2014-01-15 11:31:00 +09:00
Randy Mackay
ac99d2d19a
Copter: update AC3.1.1-rc1 release notes
2014-01-14 21:56:15 +09:00
Randy Mackay
a3527ade61
Copter: move EARTH_FRAME definition to defines.h
...
defines.h is for defining enumerations and other unchanging values while
config.h is for changeable values like parameter defaults, enabling or
disabling sensors.
2014-01-14 21:53:13 +09:00
Randy Mackay
66859686a0
Copter: remove some unused definitions
2014-01-14 21:21:54 +09:00
Randy Mackay
dd5521aa06
Copter: update version to AC3.1.1-rc1
2014-01-14 21:01:54 +09:00
Randy Mackay
b1525a421b
Copter: AC3.1.1-rc1 release notes
2014-01-14 21:01:40 +09:00
Andrew Tridgell
4f2ce31cb7
Copter: log PX4 and NuttX versions in logs
2014-01-14 15:38:51 +11:00
Andrew Tridgell
e52f8d6598
Copter: prevent log corruption during log creation
2014-01-14 14:37:48 +11:00
Andrew Tridgell
8a41b18a1f
Copter: use uppercase names on SD card where possible
2014-01-14 12:46:26 +11:00
Bill Bonney
a6078cd281
Copter: Fix SYSID ranges to support GCS display of param correctly
2014-01-14 10:32:42 +09:00
Randy Mackay
138c2803be
Copter: combine NTUN and INAV dataflash msgs
2014-01-13 22:00:11 +09:00
Randy Mackay
1e8a79eeaf
Copter: add TimeMS, InavAlt to CTUN df msg
2014-01-13 21:31:43 +09:00
Randy Mackay
97b18314ac
Copter: add time to ATT, MAG, CURR dataflash msgs
2014-01-13 20:46:54 +09:00
Randy Mackay
df9d1614e2
Copter: remove PID logging
...
Almost never used and eats up limited log description space
2014-01-13 17:23:39 +09:00
Randy Mackay
5e0ddd299f
Copter: disable OPTFLOW for SITL
2014-01-13 17:11:27 +09:00
Randy Mackay
61f319ce38
Copter: disable OPTFLOW for PX4/Pixhawk
2014-01-13 12:02:03 +09:00
Randy Mackay
b3d20bb8aa
TradHeli: Drift mode to use heli manual throttle
2014-01-10 11:06:06 +09:00
Robert Lefebvre
8b36c59d8b
TradHeli: rename Stab_Col parameters
...
With H_ prefix they appear with the rest of the tradheli specific params in the parameter list.
2014-01-10 10:51:48 +09:00
Robert Lefebvre
794890884c
TradHeli: enable Landing Collective when we are not moving
...
This prevents full negative pitch when touching down in Alt Hold or Auto-Landing.
2014-01-10 10:50:58 +09:00
Robert Lefebvre
531a9f4f25
TradHeli: disable AutoTune for Tradheli compile
...
We need the flash space, and this probably won't work for tradheli anyway since tradheli needs most of the control from Feedforward rather than P term. And D-term is very very bad.
2014-01-10 10:50:09 +09:00
Randy Mackay
9f2f44f0f6
Copter: integrate shrunken optflow
2014-01-09 12:31:53 +09:00
Randy Mackay
1793ee804e
Copter: remove armed check before logging
2014-01-07 22:43:49 +09:00
Randy Mackay
84881470b1
Copter: suspend logging while disarmed
2014-01-07 22:43:47 +09:00
Michael Oborne
757dd228d2
Copter: BugFix DO_SET_ROI returns Lat,Lon,Alt to GCS
2014-01-03 16:14:44 +09:00
Randy Mackay
99f851fc87
Copter: bugfix for starting in LOITER
...
Loiter's Roll-Pitch mode was not being set on start-up.
2013-12-30 17:18:10 +09:00
Andrew Tridgell
7c39d867bb
Copter: use file based logs in SITL
2013-12-29 07:14:21 +11:00
Andrew Tridgell
97df2f64c9
Copter: use common available_memory()
2013-12-28 16:02:32 +11:00
Randy Mackay
02898cb46e
Copter: replace APM with board in cli
2013-12-28 10:42:10 +09:00
Kevin Hester
2044300057
Copter: Split out prearm failures of low HDOP separately from !gps lock
...
(on the iris list there was some confusion on why the copter was blinking
yellow but yet they had gps lock)
2013-12-26 10:10:06 +09:00
Randy Mackay
ab1bb6886c
Copter: remove reference to COPTER_LEDS
2013-12-19 16:19:48 +09:00
Randy Mackay
d362bb45fd
Copter: move sensor init from setup(to init_ardupilot
...
This fixes a bug in which the external led was not being disabled if the
EPM was enabled (they share pins). The cause of the problem was the EPM
was being initialised before it's parameters had been loaded
2013-12-19 14:12:19 +09:00
Lukasz
cb17a5bdb6
Copter: Add RSSI_RANGE parameter
...
Added ability to rescale rssi input voltage. Useful for receivers like
FrSky which have 3.3V output.
2013-12-17 22:38:39 +09:00
Randy Mackay
21cda96f67
Copter: EPM enable/disable to APM_Config.h
2013-12-17 15:36:44 +09:00
ctech4285
2b5d8aa5b7
Copter: integrate EPM library
2013-12-17 15:36:42 +09:00
Andrew Tridgell
7f100ebe31
Copter: removed common functions
2013-12-17 12:00:46 +11:00
Andrew Tridgell
edda76623f
Copter: updates for DataFlash API changes
2013-12-17 11:51:36 +11:00
Andrew Tridgell
dd749c1de3
Copter: when using file logs use "logs" directory
2013-12-17 11:51:36 +11:00
Andrew Tridgell
7642208c1a
Copter: support MAVLink log download
2013-12-17 11:51:36 +11:00
Andrew Tridgell
9716e80e21
Copter: moved ap_message into GCS.h
2013-12-17 11:51:35 +11:00
Andrew Tridgell
eb2cb0abe0
Copter: moved GCS.h to common library
2013-12-17 11:51:34 +11:00
Andrew Tridgell
e5f098c37c
Copter: removed some unnecessary fields in GCS.h
...
save some memory
2013-12-17 11:51:34 +11:00
Randy Mackay
c7dc351609
Copter: remove unnecessary MPU6K filter definition
...
This should also help kick off the AC3.1 rebuild
2013-12-15 11:01:31 +09:00
Randy Mackay
b42a34cae0
Copter: 3.1 release notes
2013-12-14 17:08:38 +09:00
Randy Mackay
2a61053634
Copter: reduce default logging for SITL
2013-12-12 22:19:12 +09:00
Andrew Tridgell
28d98414e7
Copter: fixed some build warnings
2013-12-11 10:21:20 +11:00
Andrew Tridgell
5802d7f86b
Copter: added logging of 2nd compass
2013-12-10 13:35:04 +11:00
Andrew Tridgell
cc3ee2ec0c
Copter: added dual compass logging when available
2013-12-10 13:31:42 +11:00
Andrew Tridgell
d265e54043
Copter: changes for compass healthy API
2013-12-09 17:47:22 +11:00
Andrew Tridgell
f8e0f5c4f1
Copter: report both sets of sensors in MAVLink
2013-12-09 17:34:07 +11:00
Andrew Tridgell
f37a2c979d
Copter: don't need Log_Write_IMU2() now
2013-12-09 17:34:07 +11:00
Andrew Tridgell
ffdcb715c3
Copter: updates for compass API change
2013-12-09 17:34:06 +11:00
Andrew Tridgell
0cacc7eaeb
Copter: log both primary and secondary INS samples
2013-12-09 17:34:06 +11:00
Randy Mackay
145a8ed128
Copter: reduce autotune min rate D to 0.002
2013-12-09 14:17:31 +09:00
Randy Mackay
450e9e83c3
Copter: AC3.1-rc8 release notes
2013-12-09 12:02:28 +09:00
Randy Mackay
eb938c6ac0
Copter: reduce autotune min rate P to 0.01 (was 0.02)
2013-12-08 11:26:49 +09:00
Randy Mackay
f8165c2864
Copter: ignore yaw input during radio failsafe
2013-12-06 13:50:07 +09:00
Randy Mackay
4b3aff3f91
Copter: log flight mode to dataflash on start-up
2013-12-06 12:58:23 +09:00
Randy Mackay
cf0547e854
Copter: remove AN0~AN15 pin definitions
2013-12-06 10:28:28 +09:00
Randy Mackay
58788d2934
Copter: increasd default logging for PX4, Pixhawk
2013-12-05 16:04:52 +09:00
Randy Mackay
c5746e5434
Copter: update THR_MAX @Range and comments
2013-12-04 10:59:15 +09:00
Randy Mackay
2ba233942d
Copter: pre arm mag offset limit to 600 for PX4
2013-12-03 23:23:26 +09:00
Ben Nizette
58735ac1aa
Copter: Use AHRS heading in GLOBAL_POSITION_INT message
...
The definition of the heading field for GLOBAL_POSITION_INT is the
compass heading, and so it is used for Plane and Rover. Copter
however uses the GPS course over ground in this field.
My personal beef with this is simply that the mapping display in
MAVProxy is wrong for Copter. The question is: Do any GCS currently
rely on this field for GPS course rather than getting it from
GPS_RAW_INT as they should?
2013-12-03 20:30:02 +09:00
Randy Mackay
8fcbb7e59b
Copter: OF_Loiter update control_roll and pitch
2013-12-02 11:58:59 +09:00
Randy Mackay
9d92e46198
Copter: correct optflow logging
2013-12-02 11:58:28 +09:00
Randy Mackay
0cda3c9a71
Copter: reduce SONAR_GAIN to 0.8 (was 2.0)
2013-12-01 16:25:47 +09:00
Randy Mackay
ec65fd136d
Copter: enable external leds
2013-11-30 22:54:13 +09:00
Randy Mackay
e978a710cc
Copter: remove PIEZO_PIN definition
2013-11-30 18:21:01 +09:00
Robert Lefebvre
dbbe0f960a
Copter: remove LED_ON/OFF defines
2013-11-30 18:20:58 +09:00
Randy Mackay
59cea4b88c
Copter: remove CopterLED from main code
2013-11-30 18:20:55 +09:00
Randy Mackay
49ac1a48a5
Copter: Drift updates control_roll, pitch
...
control_roll, pitch should always hold desired roll and pitch angles now
that we have the RCIN dataflash message for recording pilot's input
2013-11-30 18:06:56 +09:00
Randy Mackay
a3be25750f
Copter: allow override of DRIFT_SPEEDGAIN
2013-11-30 15:35:59 +09:00
Randy Mackay
f12f0a6abe
Copter: drift file format fixes
...
tab replaced with four spaces
2013-11-30 15:29:26 +09:00
Randy Mackay
a744658b47
Copter: combine nav_roll and control_roll
...
Control_roll, control_pitch now always hold the desired lean angle
whether it be from the pilot or autopilot.
2013-11-27 23:11:30 +09:00
Randy Mackay
d7c636b4aa
Copter: remove yaw_in from ATT dataflash msg
2013-11-27 22:59:31 +09:00
Randy Mackay
f08cc010ea
Copter: firmware to ArduCopter V3.2-dev
2013-11-27 22:50:12 +09:00
Randy Mackay
7ef04bb73b
Copter: rename nav_yaw to control_yaw
2013-11-27 22:48:20 +09:00
Randy Mackay
a8929cd746
Copter: more complete RC output reporting to GCS
...
Radio outputs are pulled from hal.rcout instead of from motors library
which provides more complete reporting because it includes output from
sources like the camera and mount libraries.
2013-11-27 20:31:21 +09:00
Randy Mackay
10d6a9a34e
Copter: replace Log_Write_Motors with Log_Write_RCOU
2013-11-27 20:18:18 +09:00
Randy Mackay
af657d58b9
Copter: RCIN dataflash logging
2013-11-27 16:46:25 +09:00
Randy Mackay
7ae3014c14
Copter: parameter @Units to Percent*10
2013-11-26 22:35:11 +09:00
Randy Mackay
14b3547830
Copter: rename some parameter Display Names
...
Also move some parameter descriptions to @User Advanced
2013-11-26 22:17:02 +09:00
Randy Mackay
c32d77c626
Copter: fix @Group for SingleCopter
2013-11-26 21:50:29 +09:00
Andrew Tridgell
9c812d5028
Copter: added SERIAL2_BAUD and rename SERIAL3_BAUD to SERIAL1_BAUD
2013-11-26 13:05:32 +11:00
Andrew Tridgell
49062d8a37
Copter: removed extra features of copter telemetry merge
2013-11-26 13:05:32 +11:00
Andrew Tridgell
a49710f20e
Copter: added uartD support
...
this also brings GCS_Mavlink.pde closer to the plane implementation
2013-11-26 13:05:32 +11:00
Andrew Tridgell
21eac34cd1
Copter: log system ID if available
2013-11-26 13:00:03 +11:00
Randy Mackay
ed9f369492
Copter: shorten g.arming_check_enabled variable
...
g.arming_check_enabled shortened to g.arming_check
2013-11-25 17:23:39 +09:00
Randy Mackay
1645748e43
Copter: update @Range for Rate PIDs and Sonar
...
This will reduce false positives in DroneShare's tlog analyser
2013-11-25 12:52:37 +09:00
Randy Mackay
b8bfe008e1
Copter: run GPS glitch detection even when not armed
2013-11-22 21:46:32 +09:00
Randy Mackay
4e6d41bc8e
Copter: remove unused gps_fix_count
2013-11-22 11:53:50 +09:00
Randy Mackay
fe6ad3579c
Copter: log GPS messages even when no fix
2013-11-22 11:51:48 +09:00
Randy Mackay
667c3ecbf8
Copter: commit to kick-off auto rebuild for -rc7 release
2013-11-22 10:34:35 +09:00
Randy Mackay
96fdc129b1
Copter: update -rc7 release notes
2013-11-22 09:55:23 +09:00
Randy Mackay
8eb46ced53
Copter: revert pre-arm check for slow GPS
2013-11-22 09:53:21 +09:00
Randy Mackay
1a0f80ee64
Copter: AC3.1-rc7 version and release notes
2013-11-21 17:30:08 +09:00
Randy Mackay
0bc505514a
Copter: pre-arm check that INAV has no errors
2013-11-21 17:02:07 +09:00
Randy Mackay
965af43121
Copter: add INAV error count to PM dataflash msg
2013-11-21 17:02:04 +09:00
Randy Mackay
0219c85ee3
Copter: increase min LAND_SPEED to 30cm/s
2013-11-19 16:46:16 +09:00
Randy Mackay
e6a2940718
Copter: prefix SingleCopter's MOT param description
...
This should allow single copter's MOT_ parameter descriptions to be more
easily recognised as belonging to SingleCopter when viewed on the wiki's
arducopter-parameters page
2013-11-19 13:38:17 +09:00
Randy Mackay
b47cd6d5be
Copter: fix SingleCopter motor parameters link
2013-11-19 13:25:53 +09:00
Randy Mackay
7a2f49f7da
Copter: arming check for gps if GPS FS set to LAND_EVEN_STABILIZE
...
Setting the GPS Failsafe to LAND_EVEN_STABILIZE means the copter will
LAND if it loses GPS even if it's in a manual flight mode like
Stabilize. With this setting it makes sense to check the GPS quality
before arming even if we're in stabilize mode.
2013-11-18 23:59:26 +09:00
Randy Mackay
24dc4391bb
Copter: display pre-arm check failure reason every 30sec
2013-11-18 17:20:39 +09:00
Randy Mackay
d003334b75
Copter: pre-arm check for ACRO_BAL_ROLL and PITCH
2013-11-18 16:38:05 +09:00
Randy Mackay
9ee308efd5
Copter: auto disarm in Loiter, AltHold after 15sec
2013-11-18 16:13:15 +09:00
Randy Mackay
699a5bd381
Copter: radio, batt failsafe disarm if copter is landed in Loiter or AltHold
2013-11-18 15:51:17 +09:00
Randy Mackay
7dd4ab835f
Copter: CURR dataflash msg to output throttle_out
...
Previously it was outputting throttle-in which is not as useful in
autonomous modes
2013-11-18 13:30:48 +09:00
Randy Mackay
1359a8fea5
Copter: log INS errors in PM message
2013-11-18 12:16:21 +09:00
Randy Mackay
e32e83f2f0
Copter: commit to kick off MP rebuild
...
Required to push back MP Beta Firmwares version to AC3.1-rc5
2013-11-17 00:56:46 +09:00
Randy Mackay
cf21774cf4
Copter: update AC3.1-rc6 release notes again
2013-11-16 17:14:41 +09:00
Randy Mackay
9485363c53
TradHeli: dynamic flight speed minimum to 5m/s
2013-11-16 16:58:14 +09:00
Randy Mackay
a98fb174c4
Copter: batt failsafe triggers RTL from AUTO
2013-11-16 14:55:49 +09:00
Randy Mackay
fd60285121
Copter: update AC3.1-rc6 release notes
2013-11-16 14:49:03 +09:00
Randy Mackay
87127f0ab8
Copter: allow battery failsafe to trigger RTL
2013-11-16 14:46:57 +09:00
Randy Mackay
a812ef4660
Copter: minor comment update for set_mode
2013-11-16 13:56:15 +09:00
Randy Mackay
bc1e06757b
Copter: allow GPS failsafe to trigger AltHold
...
FS_GPS_ENABLE parameter accepts two new options, 2=AltHold,
3=LandEvenFromStabilize.
If set to 3 the GPS failsafe will trigger and LAND even from manual
flight modes like Stabilize and ACRO. This is useful for users who want
to ensure their copters can never stray outside the circular fence (the
fence only triggers when it knows it is outside the bounds, and it can't
know this if it has no GPS)
2013-11-16 13:55:59 +09:00
Randy Mackay
321036b72e
Copter: update contributors list
2013-11-16 12:10:38 +09:00
Randy Mackay
50f583f116
Copter: AC3.1-rc6 version and release notes
2013-11-16 11:35:01 +09:00
Randy Mackay
5cc8772947
Copter: bug fix to Tricopter motor logging
...
Fourth motor taken from yaw channel's radio_out instead of random
location in memory
2013-11-16 10:48:02 +09:00
Randy Mackay
8c9ab50ba2
TradHeli: restore CC_COMP and PIRO_COMP
2013-11-15 22:58:43 +09:00
Randy Mackay
0f67e25d37
TradHeli: set throttle_min to zero by default
2013-11-15 22:58:38 +09:00
Randy Mackay
81fc24586e
TradHeli: remove calls to get_manual_collective in auto throttle
...
set_collective_for_landing method makes this unnecessary
2013-11-15 22:58:36 +09:00
Randy Mackay
60bc9f4539
TradHeli: angle error to zero while motors runup
...
Set angle error to zero in get_roll_rate_stabilized_bf,
get_pitch_rate_stabillize_bf, get_yaw_rate_stabilized_bf.
Original commit by Rob Lefebvre
2013-11-15 22:58:34 +09:00
Randy Mackay
c9c803ffd4
TradHeli: move STAB_COL_MIN to main parameter list
2013-11-15 22:58:32 +09:00
Randy Mackay
197fc67897
TradHeli: move pilot desired rotor speed to heli.pde
2013-11-15 22:58:24 +09:00
Randy Mackay
527f05ddec
Copter: remove unused init_rate_controllers
2013-11-15 22:58:22 +09:00
Randy Mackay
4537e0aa15
Copter: add deadzone to ch8 for TradHeli
2013-11-15 22:58:20 +09:00
Randy Mackay
1f6bc7bd9c
Copter: log TradHeli ch7, ch8 in MOT message
2013-11-15 22:58:17 +09:00
Randy Mackay
19ddb8e5f3
TradHeli: integrate constructor changes to main code
2013-11-15 22:58:15 +09:00
Robert Lefebvre
bba7fdc7c3
TradHeli: ch6 tuning of ext gyro to use control_in
...
This could also be used to control the other Heli Ch7 functions (direct drive tail rotor control). This should be tidied up.
Credit: Jolyon Saunders
2013-11-15 22:58:08 +09:00
Robert Lefebvre
9ae66c1773
TradHeli: add support for drive tail rotors
...
Repurposed external gyro and made it multi-funcitonal.
required PWM on Ch8 to start the motor in RSC Mode moved up from 100 to 400. This is to facilitate two-stage switching of the motors with PWM>100 starting the tail motor, and PWM>400 starting the main motor.
Additional amendments by Randy
2013-11-15 22:58:04 +09:00
Robert Lefebvre
232a116973
TradHeli: Use Leaky Integrator on Yaw Rate controller
...
Use when rotor is not running to prevent the rudder from slowly moving over
2013-11-15 22:58:02 +09:00
Randy Mackay
3ce16113b5
TradHeli: use landing collective when landed or landing
2013-11-15 22:58:00 +09:00
Randy Mackay
633e91b7d4
Copter: initialise roll, pitch, yaw modes to stabilize
...
This fixes a bug in which the stabilize throttle controller would be
non-tilt compensated until the user switched to another flight mode and
back again
2013-11-15 22:57:56 +09:00
Randy Mackay
ae87759e6d
TradHeli: add THROTTLE_MANUAL_HELI
...
Move check_dynamic_flight to run as scheduled task
2013-11-15 22:57:53 +09:00
Randy Mackay
eaef5315bf
TradHeli: bugfix to update swash in run_rate_controllers
2013-11-15 22:57:47 +09:00
Randy Mackay
34fb70cfc7
TradHeli: formatting and param description changes
2013-11-15 22:57:45 +09:00
Randy Mackay
46118b59d7
TradHeli: integrate motor lib changes
2013-11-15 22:57:43 +09:00
Randy Mackay
72597cc5bd
TradHeli: remove setup via CLI
...
Saves 6k of flash
2013-11-15 22:57:39 +09:00
Robert Lefebvre
0e2ddb0378
Copter: verify_takeoff() should set ap.takeoff_complete to True after the takeoff is complete.
2013-11-15 22:57:34 +09:00
Robert Lefebvre
c5b119288d
TradHeli: Add Motor Runup check to the auto_arming check.
2013-11-15 22:57:31 +09:00
Robert Lefebvre
f67d95ac75
TradHeli: Modify Throttle_Auto to prevent helis from pushing hard downward while running up the motor. We will set the collective pitch to stab_col_min which should result in a mild downward pressure if the user has set their parameters correctly.
2013-11-15 22:57:28 +09:00
Robert Lefebvre
ffb605d06d
TradHeli: Modify the constrain on the auto throttle controller to prevent it from commanding full down collective if we think we are on the ground still.
2013-11-15 22:57:22 +09:00
Randy Mackay
8f2c9591ff
TradHeli: dynamic_flight flag based on inertial nav speed
...
Created new heli.pde for heli_integrated_swash and check_dynamic_flight
2013-11-15 22:57:20 +09:00
Robert Lefebvre
e23e4bc7d8
TradHeli: Bug Fix on Dynamic Flight / TakeOff Detector
2013-11-15 22:57:18 +09:00
Robert Lefebvre
324c866ae1
TradHeli: Move Take-off Complete flag from the throttle controller, and into the Dynamic Flight check. This is to prevent false positive where the collective is pushed up before the motor is started.
2013-11-15 22:57:16 +09:00
Robert Lefebvre
f7c63be357
TradHeli: leaky-I-term based on dynamic_flight_detector
2013-11-15 22:57:14 +09:00
Randy Mackay
f0f6e85b39
Copter: ARMING_CHECK made into bitmask
...
Allows arming checks to be individually enabled or disabled for baro,
compass, GPS, INS, parameters, RC and board voltage
2013-11-15 17:13:56 +09:00
Randy Mackay
fe822ba0b6
Copter: pre-arm check of INS health
2013-11-15 17:13:53 +09:00
Jason Short
371dc8c616
Copter: Drift Mode
...
Changes Toy mode declarations to Drift mode.
Requires GPS, Mode 2 transmitter
Drift mode mixes Roll, Pitch and Yaw into a single stick on mode two transmitters.
2013-11-14 14:43:15 +09:00
Randy Mackay
57b291b1c5
Copter: reject change_command if not in AUTO
2013-11-14 13:49:37 +09:00
Randy Mackay
0778454434
Copter: disarm routine shortcut
...
Extra check so we only run the disarm check when we are actually armed.
The ground stations sometimes send many disarm messages which can be
ignored
2013-11-14 13:14:51 +09:00
Randy Mackay
f5b1114aea
Copter: range check pilot requested lean angles
...
This fixes a bug uncovered by MHA in which the receiver output 900 pwm
for roll and pitch to the APM which was interpreted as requesting an 80
deg lean angle which the copter then attempted to do!
2013-11-13 14:21:21 +09:00
Randy Mackay
159d6320bf
Copter: move SINGLE parameters to start at 75
2013-11-12 23:40:38 +09:00
Randy Mackay
06ce98a2f4
Copter: add SINGLE_FRAME definition
2013-11-12 23:40:32 +09:00
ssq870424
07d3f2a3c5
Copter: add support for singlecopter airframe
...
this is the newest singlecopter airframe programme.
This kind of aerial vehicles include Honeywell T-hawk and Goldeneye.
2013-11-12 23:40:27 +09:00
Randy Mackay
13fd33c2d8
Copter: gps failsafe disabled until we get first 3d lock
2013-11-12 11:13:05 +09:00
Randy Mackay
f29f7d9777
Copter: bug fix to take-off in Loiter and AltHold
...
Always set the target altitude after take-off to be current altitude +
20cm. This resolves a bug in which the target altitude could end up
being a couple of meters higher than the current altitude if the user
entered Loiter / Alt Hold mode before inertial nav altitude estimate had
settled.
2013-11-11 22:29:09 +09:00
Randy Mackay
03831cdd28
Copter: GPS ok only when not glitching
...
Removed redundant checks to GPS_ok before setting flight mode to RTL
(this check is already performed inside the set_mode function)
Removed reset of home distance and bearing when GPS lock is lost, it now
remains at the last known value
2013-11-11 22:24:18 +09:00
Randy Mackay
e4d8c673f3
Copter: force gyro calibration on start-up
2013-11-10 21:51:54 +09:00
Andrew Tridgell
6b1f59372c
Copter: show git and firmware version in tlog
2013-11-09 10:09:20 +11:00
Andrew Tridgell
b41f4898e0
Copter: report INS health
2013-11-07 12:48:17 +11:00
Andrew Tridgell
2f6cfd1ff8
Copter: update for AHRS API changes
2013-11-04 21:21:42 +11:00
Randy Mackay
620109d894
Copter: formatting fix to config.h
2013-11-03 12:57:02 +09:00
Robert Lefebvre
8868af7c2f
TradHeli: Change default Auto-Yaw to Yaw Look Ahead
...
This leads to smoother flight in Auto modes, particularly with fast waypoints.
2013-11-03 12:56:57 +09:00
Jason Short
66b8ca3a27
Copter: updated toy gains
2013-11-03 10:14:10 +09:00
Jason Short
2a82d1b0b0
Copter: CH7 SaveWP fix corner case
...
If the user is on the ground and flips CH7, do nothing instead of recording a bad takeoff altitude. Do another check to avoid a land right after a takeoff.
2013-11-02 21:34:55 +09:00
Randy Mackay
8278767d0a
Copter: remove unused get_acro_yaw
2013-11-02 21:34:53 +09:00
Jason Short
c3aa56459a
Copter: remove unused Toy param
2013-11-02 21:34:50 +09:00
Jason Short
520a535c21
Copter: TOY mode updates
2013-11-02 21:34:48 +09:00
Andrew Tridgell
f6f6caafc8
Copter: int gyros on arm, not on first boot
...
this makes first boot much faster
2013-11-02 21:41:11 +11:00
Randy Mackay
977983904f
Copter: arming check that throttle is above failsafe
2013-11-02 14:06:19 +09:00
Randy Mackay
aaf642c223
Copter: disable autotune if pilot moves yaw stick
2013-11-02 12:12:46 +09:00
Randy Mackay
94f301181e
Copter: recalc distance to home during arming
...
fixes an rare edge case in which the fence could trigger immediately
after arming
2013-11-01 23:54:32 +09:00
Randy Mackay
798c4e2278
Copter: more Ch7/Ch8 event logging
...
Additional event logging for SaveWP, Fence, Acro trainer, Save Trim
2013-11-01 11:53:16 +09:00
Randy Mackay
babc54ec60
Copter: default Ch7 to DO_NOTHING
...
Ch7/Ch8 Save_WP feature triggers when switch is brought high (instead of
low) to be consistent with other aux features
2013-11-01 11:42:33 +09:00
Randy Mackay
97770ae352
Copter: rc10, rc11 available even without MOUNT
2013-10-31 22:55:02 +09:00
Randy Mackay
de08116320
Copter: disable some aux channels on hexa and octas
...
Resolves issue #324
2013-10-31 15:22:34 +09:00
Randy Mackay
65980ace68
Copter: remove some commented out send_text code
2013-10-30 13:44:56 +09:00
Randy Mackay
8a6c2a6588
Copter: add alt and throttle checks to crash detector
2013-10-30 13:33:09 +09:00
Randy Mackay
2326b2e5f5
Copter: crash checker
...
Crash is determined to have happened when the copter is 20deg more than
the ANGLE_MAX parameter continuously for more than 2 seconds
Not activated when in ACRO mode or while flipping
2013-10-29 22:15:12 +09:00
Randy Mackay
8386b658e9
Copter: add ANGLE_RATE_MAX param
...
Limits the maximum rotation rate requested by the angle controller which
is used in stabilize, loiter, rtl and auto flight modes
2013-10-29 11:27:05 +09:00
Randy Mackay
9176bf2e97
Copter: add @Increment to battery failsafe descriptions
2013-10-29 11:24:04 +09:00
Andrew Tridgell
2016bf1f31
Copter: fixed HIL build
2013-10-28 18:35:39 +11:00
Andrew Tridgell
a44e3191df
Copter: fixed baro-only preflight cal
...
this was causing a full level, which mucked up the INS calibration
2013-10-28 16:54:32 +11:00
Randy Mackay
9df7185075
Copter: remove unused #defines from config.h
2013-10-28 12:37:41 +09:00
Randy Mackay
465cb8ab25
Copter: add features that can be disabled to APM_Config.h
2013-10-28 12:36:52 +09:00
Randy Mackay
36832aaa61
Copter: remove ins from InertialNav object instantiation
2013-10-27 13:41:52 +09:00
Tobias
a7e7084f27
Copter/position_vector: remove const specifiers on objects returned by
...
value
2013-10-27 13:41:46 +09:00
Tobias
7564cc02af
Copter: use const refs instead of unneeded copies
2013-10-27 13:41:06 +09:00
Tobias
d6d5f0bbe4
Copter: Log.pde: replace unused copy with ref (saves again some bytes)
2013-10-27 13:40:40 +09:00
Tobias
4d4b419d25
Copter: add comment (unit of G_Dt)
2013-10-27 13:39:17 +09:00
Randy Mackay
8e62035328
Copter: remove unnecessary check of flight mode from fence response
2013-10-24 16:42:14 +09:00
Randy Mackay
d86ac9041e
Copter: report RC receiver health to GCS
2013-10-24 16:32:55 +09:00
Andrew Tridgell
6138dca2b2
Copter: set system time on GPS lock
2013-10-24 14:22:48 +11:00
Andrew Tridgell
92bf4b9c89
Copter: added MAVLink SYSTEM_TIME message
2013-10-24 14:22:47 +11:00
Randy Mackay
7c5982c573
Copter: remove unnecessary Log_Write_Optflow
2013-10-23 20:46:35 +09:00
Randy Mackay
f52c6add89
Copter: reenable optical flow by default
...
correct optflow test compile error
2013-10-23 20:42:03 +09:00
Randy Mackay
8ea3e68620
Copter: bug fix for loading missions while armed
2013-10-23 14:12:03 +09:00
Randy Mackay
030f479ac1
Copter: firmware update to AC3.1-rc5
2013-10-22 16:04:13 +09:00
Randy Mackay
fb49cd82c1
Copter: add LAND to aux switch
...
Fix aux switch AUTO and RTL so they resets flight mode if still in those
modes when switch brought low
2013-10-22 13:13:36 +09:00
Randy Mackay
c98d375e49
Copter: update @Units to pwm on throttle params
2013-10-21 20:33:56 +09:00
Randy Mackay
bbc4cb263f
Copter: only allow autotuning when flying
2013-10-21 17:58:10 +09:00
Randy Mackay
6b9b5c5617
Copter: pre-arm check speed is less than 50cm/s
2013-10-20 21:56:00 +09:00
Randy Mackay
5499c6ea6d
Copter: autotune bug fix for starting autotune
...
log completion to dataflash
2013-10-20 13:54:36 +09:00
Randy Mackay
6d76652e48
Copter: autotune set original gains on reset
...
Update from Leonard
2013-10-20 11:47:59 +09:00
Michael Oborne
78c4e03fd5
sensor hil fix
2013-10-19 23:04:22 +09:00
Randy Mackay
4036f50fc2
Copter: bug fix to convert old batt params to BATT_ lib
2013-10-19 22:55:47 +09:00
Randy Mackay
6c0cb5f84d
AutoTune: bug fix and GCS messages
2013-10-19 21:54:18 +09:00
Randy Mackay
390a8c02a5
Copter: enable AUTOTUNE by default
2013-10-18 13:58:08 +09:00
Randy Mackay
0cbedded0d
Copter: autotune to use 2pos switch only
...
method of recording state also changed
other code clean-up
pair programmed withe Leonard
2013-10-18 13:57:50 +09:00
Randy Mackay
2e75d5dec3
Copter: autotune log when limits reached
2013-10-17 11:05:31 +09:00
Randy Mackay
c59dee045c
Copter: autotune restore orig pids if user changes flight mode
2013-10-17 10:56:53 +09:00
Randy Mackay
f13b45467f
Copter: autotune bug fix for restarting tuning from suspended state
2013-10-17 10:56:10 +09:00
Randy Mackay
5ac3bf4915
Copter: adjust autotune P and D min and max
2013-10-17 10:20:16 +09:00
Randy Mackay
7c7f235a97
Copter: ignore flight mode change requests if we're already in the desired mode
2013-10-15 11:53:56 +09:00
Randy Mackay
deb171a869
Copter: correct UserHooks typos
2013-10-15 11:18:00 +09:00
Randy Mackay
aa7a1a5af3
Copter: correct GCS send times task estimates
2013-10-13 20:53:51 +09:00
Randy Mackay
d2bbc06502
Copter: allow throttle deadband to be redefined in APM_Config.h
2013-10-13 20:41:11 +09:00
Randy Mackay
959f59f623
Copter: correct mount tasks scheduler time
...
Having the estimate too high would mean it would likely never run
2013-10-13 14:13:59 +09:00
Randy Mackay
f344c77cca
Copter: AC3.1-rc4 version and release notes
2013-10-13 14:12:18 +09:00
Randy Mackay
bf74a64fec
Copter: add GPS glitch to arming checks
2013-10-13 14:04:54 +09:00
Randy Mackay
8de6c34252
Copter: comments update for GPS_HDOP_GOOD parameter
2013-10-13 13:53:26 +09:00
Randy Mackay
32f53624d6
Copter: rename low_battery to failsafe.battery
2013-10-13 13:52:52 +09:00
Randy Mackay
0e740bd4e1
Copter: enable AUTOTUNE for mission planner build
2013-10-13 11:57:50 +09:00
Randy Mackay
6876107a15
Copter: autotune disables rate output from stab controller
2013-10-13 11:56:01 +09:00
Andrew Tridgell
b69f08c03e
Copter: reduce timer speed to 500 on APM2
...
this reduces the cost of timer interrupts
2013-10-13 11:03:41 +09:00
Andrew Tridgell
09a1d35e62
Copter: fixed build for no COPTER_LEDS
2013-10-13 11:03:33 +09:00
Andrew Tridgell
d38d9ea88f
Copter: changes for AP_Mount API
2013-10-13 11:03:26 +09:00
Randy Mackay
8706810d55
Copter: scheduler times corrections
2013-10-13 11:03:22 +09:00
Randy Mackay
6be6bd5aed
Copter: remove unused battery analog sources
2013-10-13 11:03:20 +09:00
Randy Mackay
d2bda8c235
Copter: split up medium loop
2013-10-13 11:03:15 +09:00
Randy Mackay
e9cefbafd1
Copter: higher priority for throttle loop, lower telemetry
2013-10-13 11:03:10 +09:00
Andrew Tridgell
64d34dc125
Copter: give UARTA 512 bytes
...
this reduces load by allowing more contiguous writes to the serial
buffers
2013-10-13 11:02:55 +09:00
Andrew Tridgell
3b9566bc09
Copter: support MAV_CMD_DO_SET_CAM_TRIGG_DIST
2013-10-11 21:40:57 +11:00
Craig3DRobotics
93cbfbe46c
Copter:Parameter descriptions updated
2013-10-09 15:31:31 -07:00
Randy Mackay
8d1085feea
Copter: pre-arm expects mag len of 330 for APM1 (was 530)
2013-10-09 14:10:16 +09:00
Randy Mackay
7e657ce856
AutoTune: abandon tuning if rate P hits minimum
...
Fixes from Leonard
2013-10-09 13:35:43 +09:00
Randy Mackay
fc47e05105
Copter: update firmware version to AC3.1-rc3
2013-10-09 11:13:15 +09:00
Andrew Tridgell
450323f4ae
Copter: enable logging on Linux
2013-10-08 19:20:35 +11:00
Andrew Tridgell
4b68dd48f7
Copter: use ins.wait_for_sample() for main loop
...
this takes advantage of the INS specific method to wait for a sample
2013-10-08 19:20:34 +11:00
Randy Mackay
9435eb4a15
Copter: remove unused flags and consolidate ap and ap_system
2013-10-08 15:25:14 +09:00
Andrew Tridgell
6145924481
Copter: switch Linux to L3G4200D ins driver
2013-10-08 11:50:54 +11:00
Randy Mackay
fbb295a0a1
Copter: correct HLD_LAT_P and HLD_LON_P ranges
2013-10-07 14:45:39 +09:00
Kevin Hester
d29781104f
AC: fix autodocs for SUPER_SIMPLE so the GCSes can show the right options
2013-10-07 11:33:02 +09:00
Randy Mackay
f56617710f
Copter: pre-arm RC checks ch3's min and max
2013-10-07 11:17:16 +09:00
Randy Mackay
efc02161c4
Copter: add safe switch arming check
2013-10-05 22:23:53 +09:00
Randy Mackay
0c0de7c53e
Copter: simple mode speedup
...
super simple and simple mode headings separated
g.super_simple converted into a bitmap by flight mode switch position
2013-10-05 18:26:56 +09:00
Randy Mackay
ba92c4891a
Copter: make AutoTune a compile-time option
2013-10-04 15:50:50 +09:00
Randy Mackay
31cea0140d
Copter: Leonard's AutoTuning for Roll and Pitch
2013-10-04 15:50:47 +09:00
Randy Mackay
09de917b27
Copter: mavlink ext status to use abs pressure
2013-10-04 13:20:58 +09:00
Randy Mackay
a33060b66d
Copter: mavlink extended status gps bit not-healthy when glitching
...
add optflow health to extended status
mavlink heartbeat status to critical on any failsafe
extended status msg to use SYS_STATUS_SENSOR enum
2013-10-03 22:11:55 +09:00
Randy Mackay
3c5797c479
Copter: sent current as -1 to GCS when can't be monitored
2013-10-03 11:16:31 +09:00
Randy Mackay
dab4f032f9
Copter: integrate BattMonitor
2013-10-03 11:16:28 +09:00
Andrew Tridgell
32a016a66f
Copter: updates for AP_HAL::MemberProc
2013-09-30 21:06:43 +10:00
Andrew Tridgell
3665bec26d
Copter: fixed build for Linux
2013-09-28 22:04:16 +10:00
Andrew Tridgell
9e42e536a7
Copter: make the scheduling a bit more multi-tasking OS friendly
...
we can afford to sleep a bit in the main loop
2013-09-28 22:04:16 +10:00
Andrew Tridgell
234eaceb14
Copter: update for Stub -> HIL
2013-09-28 22:04:15 +10:00
Andrew Tridgell
a0f9055a9d
Copter: use new scheduler API
2013-09-28 21:24:03 +10:00
Randy Mackay
c3f7146f03
Copter: improve check of frame type to catch spelling errors
2013-09-27 14:35:16 +09:00
Randy Mackay
e295d4555d
Copter: send frame type in mavlink heartbeat msg
2013-09-27 14:35:13 +09:00
Randy Mackay
a53d28e018
Copter: remove support for dmp ahrs
2013-09-27 10:42:49 +09:00
Andrew Tridgell
394645560a
Copter: update for new INS API
2013-09-27 10:49:00 +10:00
Andrew Tridgell
566eaf7d41
Copter: fixed flymaple build with copterleds
2013-09-27 10:32:22 +10:00
Andrew Tridgell
a0b6481dfd
Copter: removed SMACCM support
2013-09-26 22:38:31 +10:00
Randy Mackay
5cac1b3c92
Copter: ignore aux switch during radio failsafe
2013-09-26 20:19:39 +09:00
Randy Mackay
fd2e87b710
Copter: disable tuning during radio failsafe
2013-09-26 20:05:25 +09:00
Randy Mackay
6b97994dcd
Copter: ignore switch changes during transitions in or out of radio failsafe
2013-09-26 19:37:22 +09:00
Randy Mackay
7cc8a9038f
Copter: move failsafe flags into structure
2013-09-26 19:37:15 +09:00
Randy Mackay
02f7310689
Copter: make it easier for Arduino users to easily reduce flash space by turning off features
2013-09-26 13:15:30 +09:00
Randy Mackay
2c96ed3f22
Copter: disable optical flow
...
This at least allows ArduCopter to be compiled with arduino until we
find larger flash savings
2013-09-24 21:59:19 +09:00
Randy Mackay
589200042d
Copter: remove declination setup from CLI
2013-09-24 21:45:54 +09:00
Randy Mackay
09756e16b7
Copter: remove battery setup from CLI
2013-09-24 21:45:54 +09:00
Randy Mackay
3bf1352701
Copter: shorten motor tests printf
2013-09-24 21:45:53 +09:00
Randy Mackay
8cce837f77
Copter: remove accel level from cli
...
the accel command should always be used in place of level
2013-09-24 21:45:52 +09:00
Randy Mackay
77b5cb5d3f
Copter: correct typo in error #define
2013-09-24 21:45:52 +09:00
Randy Mackay
8a886c0e19
Copter: remove err msg for undefined throttle mode
...
Printing errors like this to the console are unlikely to ever be seen
2013-09-24 21:45:51 +09:00
Randy Mackay
284aa2217f
Copter: remove old comments
2013-09-24 21:45:43 +09:00
Randy Mackay
e5535e35b3
Copter: remove unused reset_stability_I
2013-09-24 21:42:05 +09:00
Randy Mackay
d7782e1356
Copter: remove tune from cli to save 300bytes flash
2013-09-24 21:42:02 +09:00
Randy Mackay
1cc2c8d6a5
Copter: reduce compassmot flash by 500 bytes
2013-09-24 21:41:59 +09:00
Randy Mackay
c596b27719
Copter: add dataflash error for GPS glitch
2013-09-24 21:41:48 +09:00
Randy Mackay
6c5294f89e
Copter: integrate GPS_Glitch parameters
2013-09-24 21:41:45 +09:00
Randy Mackay
29b30cf752
Copter: gps failsafe on lengthy glitches
2013-09-24 21:41:30 +09:00
Randy Mackay
4c8227c050
Copter: update AP_Notify for gps failsafe and glitching
2013-09-24 21:41:28 +09:00
Randy Mackay
262fcb301a
InertialNav: rename set_current_position to set_home_position
2013-09-24 21:41:19 +09:00
Randy Mackay
2f5b32bada
Copter: integrate GPS_Glitch's check_position
2013-09-24 21:41:16 +09:00
Andrew Tridgell
3378c7901a
Copter: added support for the flymaple board
2013-09-24 13:51:28 +10:00
Andrew Tridgell
91315715fe
Copter: removed CONFIG_PUSHBUTTON
...
not used anywhere any more
2013-09-23 18:10:22 +10:00
Andrew Tridgell
3ffeff04a7
Copter: removed logging of MAVLink parameter changes
...
not much point to this
2013-09-23 18:10:22 +10:00
Andrew Tridgell
a8796f2f76
Copter: make compat functions static
...
this prevents conflicts with libmaple
2013-09-23 18:10:22 +10:00
Andrew Tridgell
35e3c887d2
Copter: use new baro API
2013-09-21 21:30:54 +10:00
Andrew Tridgell
b6a0577723
Copter: only send RC_CHANNELS_SCALED in HIL
...
saves a bit of telemetry bandwidth
2013-09-21 09:30:30 +10:00
Andrew Tridgell
faddef69e6
Copter: fixed baud rates on APM1
2013-09-21 09:30:29 +10:00
Andrew Tridgell
46688454c4
Copter: removed flash_leds() calls
2013-09-19 18:38:28 +10:00
Andrew Tridgell
754bdbd25f
Copter: use new usb_connected() HAL function
2013-09-19 16:24:23 +10:00
Randy Mackay
642a9b3df4
Copter: update AC3.1-rc2 release notes for COMPASS_ORIENT change
2013-09-19 13:00:11 +09:00
Randy Mackay
79399e4fb4
Copter: AC3.1-rc2 version and release notes
2013-09-18 13:30:26 +09:00
Randy Mackay
65adb78f31
Copter: increase default battery capacity to 3500mAh
2013-09-15 11:54:07 +09:00
Randy Mackay
0fa8e44377
Copter: remove cli eprom dump
2013-09-15 11:44:53 +09:00
Randy Mackay
0232b25f6e
Copter: update LED_MODE bitmask @values to always enable leds
2013-09-15 11:38:47 +09:00
Randy Mackay
ea3d388796
Copter: update release notes to add slow take-off
2013-09-13 20:53:39 +09:00
Randy Mackay
daa0cb7914
Copter: enable motor slow start in auto mode
2013-09-13 14:32:19 +09:00
Randy Mackay
98a2ffd65c
Copter: remove redundant reset_i_all from startup
2013-09-13 12:30:25 +09:00
Andrew Tridgell
3720efc7c9
Copter: changed to AP_Vehicle.h
2013-09-13 11:47:03 +10:00
Randy Mackay
b4b2128977
Copter: update @Range comments for THR_MIN
...
This should help reduce change of someone setting THR_MIN above 300 (30%
throttle)
2013-09-12 22:45:18 +09:00
Randy Mackay
c5bd1a76ed
Copter: comment update re low battery event
2013-09-12 22:41:28 +09:00
Randy Mackay
653a5036ae
Copter: #define for initial altitude jump during take-off
...
Developers can add a line like to APM_Config.h to reduce the initial
jump when taking off in Loiter or AltHold flightmodes:
#define ALT_HOLD_TAKEOFF_JUMP 0
2013-09-12 22:31:42 +09:00
Randy Mackay
072b231c3f
Copter: integrate slow start feature
2013-09-12 22:29:53 +09:00
Randy Mackay
36bbed8fdd
Copter: removed calls to set motor's max throttle
2013-09-12 22:28:38 +09:00
Andrew Tridgell
adc923b989
Copter: update battery pin docs
2013-09-12 13:43:15 +10:00
Andrew Tridgell
d9fe0552f0
Copter: allow Vcc checks on Pixhawk
2013-09-12 13:43:06 +10:00
Andrew Tridgell
7c62736e59
Copter: fixed Vcc
2013-09-12 13:26:19 +10:00
Andrew Tridgell
4545445850
Copter: fixed SR0 and SR3 autodocs
2013-09-12 09:53:13 +10:00
Randy Mackay
a68966e077
Copter: integrate sprayer pump test
2013-09-11 17:05:25 +09:00
Randy Mackay
152f5da880
Copter: integrate AP_Notify batt and radio failsafes
2013-09-11 14:36:38 +09:00
Randy Mackay
9095c6ab30
Copter: update Release notes for AC3.1-rc1 again
2013-09-11 09:51:47 +09:00
Randy Mackay
8e0cacad39
Copter: disable low battery events when usb connected
2013-09-09 21:27:05 +09:00
Kevin Hester
240a9ccaf0
AC: if vehicle is !flying show hb state as MAV_STATE_STANDBY
...
This helps GCSes determine the appropriate UI for the current vehicle
mode.
2013-09-09 20:51:54 +09:00
Randy Mackay
43c4ba304d
Copter: update Release Notes for AC3.1-rc1
2013-09-09 20:04:30 +09:00
Randy Mackay
1d55fa6818
Copter: add arm check of GPS hdop when in Loiter
2013-09-09 14:03:40 +09:00
Randy Mackay
1abb439051
Copter: move acro's var initialisation to roll-pitch and yaw controller initialisation
2013-09-09 10:54:13 +09:00
Randy Mackay
942ba0476b
Copter: remove manual_attitude and throttle flags
2013-09-09 10:44:53 +09:00
Randy Mackay
b7579bb028
Copter: move init of global nav variables to set_nav_mode
2013-09-09 10:37:44 +09:00
Randy Mackay
4842335a24
Copter: add #include for AC_Sprayer
2013-09-09 10:18:06 +09:00
Randy Mackay
13ee672eae
Copter: remove unused get_acro_pitch and roll
2013-09-09 10:11:23 +09:00
Craig3DRobotics
630095adaa
Revert "Copter: Corrected SR0 & SR3 parameter descriptions"
...
This reverts commit 6568234018
.
2013-09-06 09:58:19 -07:00
Craig3DRobotics
f1a674ad26
Copter: Correction on SR0 & SR3 parameter description.
2013-09-05 22:28:34 -07:00
Andrew Tridgell
979636936d
Copter: support reboot to bootloader
2013-09-04 11:59:02 +10:00
Andrew Tridgell
52f5b1e5a7
Copter: update to GPLv3 license headers
2013-08-30 13:01:39 +10:00
Andrew Tridgell
1b99ef5e4f
Copter: added a delay in ESC calibration
...
this allows AP_Notify to run via the delay callback
2013-08-30 13:01:36 +10:00
Andrew Tridgell
e1e32fcf08
Copter: fixed build with AP_AHRS changes
2013-08-30 13:01:35 +10:00
Andrew Tridgell
25d517f5d6
Copter: updates for new notify API
2013-08-30 13:01:35 +10:00
Randy Mackay
4aef49a006
Copter: re-order #defines of AP_Notify
2013-08-30 13:01:35 +10:00
Randy Mackay
52ef77393c
Copter: integrate Toshiba_LED_PX4
2013-08-30 13:01:35 +10:00
Randy Mackay
46c24fdf39
Copter: integrate ToshibaLED
2013-08-30 13:01:35 +10:00
Randy Mackay
e985253f1a
Copter: integrate notify
2013-08-30 13:01:35 +10:00
Randy Mackay
7c78936bc5
Copter: land by default at end of RTL
2013-08-30 10:34:23 +09:00
Craig3DRobotics
6568234018
Copter: Corrected SR0 & SR3 parameter descriptions
2013-08-29 12:19:04 -07:00
Randy Mackay
81074ebb3c
Copter: update Y6 defaults
2013-08-28 13:05:01 +09:00
Randy Mackay
6052017b13
Copter: allow override of auto throttle mode
2013-08-28 11:45:07 +09:00
Randy Mackay
45aeb1a921
Copter: split up loiter into 4 steps
...
Reduces disruption to the main loop but also introduces a delay of 30ms
to navigation output
2013-08-28 11:33:10 +09:00
Andrew Tridgell
d5e28e72cc
Copter: support new RADIO_STATUS msg
2013-08-24 17:59:13 +10:00
Randy Mackay
7159c539e6
Copter: skip mode change checks when disarmed
...
Note: there will be a follow up commit to move the checks into a
separate function so they can be called just before arming
2013-08-22 13:25:27 +09:00
Randy Mackay
d8eb7fb82f
Copter: remove x100 from IMAX definitions
2013-08-19 22:38:34 +09:00
Andrew Tridgell
a06f8a156d
Copter: fixed PX4 build
2013-08-19 21:12:41 +10:00
Randy Mackay
fd047cc968
Copter: AUTO ch7/ch8 option
2013-08-19 18:09:23 +09:00
Randy Mackay
2696e160e6
Copter: surface tracking improvement
...
Separate correction speeds for pilot input vs altitude-above-ground
errors to allow slower correction to sonar signals.
Change SONAR_GAIN parameter to be altitude error -> desired speed. This
means it should be set 10x larger than before.
Replace hard-coded sonar cut-off percentage of 70% with
SONAR_RELIABLE_DISTANCE_PCT.
Reduce sonar cut-off percentage to 60%.
Add desired sonar altitude to dataflash log's CTUN message.
2013-08-19 09:52:59 +09:00
Randy Mackay
88332b4acb
Copter: revert to 3 element sonar's mode filter
2013-08-19 09:47:48 +09:00
Randy Mackay
3a5a15a15f
Copter: allow CH6 tuning of sonar gain
2013-08-18 15:44:54 +09:00
Randy Mackay
fe56ac3839
Copter: only allow auto_trim in STABILIZE
2013-08-15 21:11:23 +09:00
Randy Mackay
69da4e99f8
Copter: add ch7/ch8 Auto and Land option
...
CH7/CH8 high initiates AUTO mode, low initiates Land. Ideally high
would be a new take-off flight mode so this may need some rework.
2013-08-15 16:08:33 +09:00
Randy Mackay
ac620e2140
Copter: Loiter and AltHold won't breach alt fence
2013-08-15 16:06:27 +09:00
Randy Mackay
6a2daf1a33
Copter: reduce sonar sensitivity to spikes
2013-08-15 16:04:17 +09:00
Randy Mackay
34e874282e
Copter: only check hdop when circular fence enabled
2013-08-15 16:03:57 +09:00
Randy Mackay
b40cd07ce9
Copter: switch to LOITER when exiting mission
2013-08-15 13:09:57 +09:00
Randy Mackay
d000967a76
Copter: pre-arm check for gps hdop < 2
2013-08-15 13:06:36 +09:00
Randy Mackay
8b79798e8d
Copter: Leonard's sport fix re slow roll
2013-08-11 22:15:27 +09:00
Randy Mackay
34b11f7be0
Copter: angle limiter fix for max lean angle
2013-08-11 14:55:49 +09:00
Randy Mackay
6969ab573d
Copter: configurable max lean angle
...
ANGLE_MAX parameter allows limiting the roll and pitch angles during
manual and auto flight modes to anywhere from 10 to 80 degrees
2013-08-11 12:53:22 +09:00
Randy Mackay
5049595a2c
Copter: SPORT mode to use alt hold
2013-08-10 15:42:02 +09:00
Randy Mackay
d0dc5813cf
Copter: move CIRCLE_RADIUS definition
2013-08-07 14:03:28 +09:00
Randy Mackay
e1fe4946fb
Copter: Sprayer enable added to CH7/CH8 switch
2013-08-05 21:12:29 +09:00
Randy Mackay
74fb500efe
Copter: integrate AC_Sprayer
2013-08-05 21:12:23 +09:00
Randy Mackay
49dbdce89c
Copter: split ACRO_P into ACRO_RP_P and ACRO_YAW_P
2013-08-05 21:05:00 +09:00
Randy Mackay
82082e044c
Copter: remove ACRO's axis enabled parameter
...
Acro is now body frame (with earth frame leveling) while Sport is earth
frame acro
2013-08-05 21:04:57 +09:00
Randy Mackay
786d6824ae
Copter: Acro Trainer added to Ch7/Ch8 switch
2013-08-05 21:04:55 +09:00
Randy Mackay
21e523b9ac
Copter: Acro trainer separated into limited and leveled
2013-08-05 21:04:53 +09:00
Randy Mackay
e32342163d
Copter: rename ACRO variables
2013-08-05 21:04:50 +09:00
Leonard Hall
d2deaaa686
Copter: Acro add rate constrain and combine limit calc
2013-08-05 21:04:47 +09:00
Randy Mackay
65276d360b
Copter: SPORT to use YAW_HOLD
2013-08-05 21:04:44 +09:00
Randy Mackay
39ab4f62ef
Copter: add SPORT mode
2013-08-05 21:04:41 +09:00
Randy Mackay
a18d55a9d3
Copter: update version to 3.1-dev
2013-08-05 14:26:52 +09:00
Andrew Tridgell
086c7d70d8
Copter: use const references for Vector3f parameters
...
this is more efficient than passing a whole structure on the stack
Pair-Programmed-With: Brandon Jones <brnjones@gmail.com>
2013-08-05 10:24:24 +10:00
Andrew Tridgell
c4f11e6c74
Copter: fix longitude_scale() call for new API
...
Pair-Programmed-With: Brandon Jones <brnjones@gmail.com>
2013-08-05 10:24:21 +10:00
Andrew Tridgell
2690edfc5f
Copter: ask for IMU samples at 100Hz
...
this produces the same result, but makes things simpler in the driver
2013-08-02 21:37:15 +10:00
Andrew Tridgell
01e19a32fe
Copter: use the new scheduler load_average() call
...
this also simplifies the main loop
2013-08-02 18:46:34 +10:00
Randy Mackay
9672742b42
Copter: bug fix to look_ahead_yaw
...
Fix received from David Dewey
Was incorrectly using the direction instead of heading when deciding
whether to point forward or not. Reduced YAW_LOOK_AHEAD_MIN_SPEED to
1m/s because bug meant it was nearly always pointing forward and 10m/s
(the old value) seemed too high
2013-08-01 14:12:55 +09:00
Randy Mackay
c30cfa21c5
Copter: resolve compiler warning re unused variable
2013-07-29 16:46:25 +09:00
Randy Mackay
0f8f5bc048
Copter: remove unused ap.gps_status flag
2013-07-29 16:46:05 +09:00
Randy Mackay
2c48c20088
Copter: generalize 3 pos switch for all ch7/ch8 options
2013-07-29 16:28:04 +09:00
Olivier-ADLER
87d062905e
Copter: 3 positions switch support for CH7 and CH8 - new 3 positions SIMPLE / SUPERSIMPLE mode
...
3 positions modes must use mode number >= 100
pre-arm check correction for CH7 - CH8 check
2013-07-29 15:12:10 +09:00
Randy Mackay
c173f0c7d9
Copter: change CH7/CH8 pre-arm check string
2013-07-29 14:32:27 +09:00
Randy Mackay
0d75203d87
Copter: minor format change to exit_mission function
2013-07-28 18:19:05 +09:00
Randy Mackay
12da2d160a
Copter: set landing_complete flag to false on start-up
2013-07-28 18:19:03 +09:00
Randy Mackay
3b59cde1b8
Copter: deactivate accel throttle controller when landed
2013-07-28 18:19:01 +09:00
Randy Mackay
da37089dc2
Copter: remove landing checks in loiter controller
2013-07-28 18:18:57 +09:00
Randy Mackay
8eefbdce44
Copter: turn off stability patch when landed in Loiter
2013-07-28 18:18:54 +09:00
Randy Mackay
9a1a999fba
Copter: landing check changes
2013-07-28 18:18:50 +09:00
Randy Mackay
dbc18ee900
Copter: allow arming in AltHold and Loiter if landed
2013-07-28 18:18:47 +09:00
Randy Mackay
24d15517ff
Copter: clear thr accel I term on take-off
2013-07-28 18:18:45 +09:00
Randy Mackay
05248738e2
Copter: bug fix for take-off in loiter
2013-07-28 18:18:43 +09:00
Randy Mackay
c3daf78340
Copter: reset loiter target when landed
2013-07-28 18:18:41 +09:00
Randy Mackay
fe412437c2
Copter: add flags for upper and lower throttle limits
...
Freeze desired altitude when motors hit a limit
2013-07-28 18:18:39 +09:00
Olivier-ADLER
bf6120d8b7
Copter: Move CH7 - CH8 check from read_aux_switches() to pre_arm_checks.
...
Moving this to pre-arm checks save some processing time and is safer.
2013-07-26 09:30:24 +09:00
Randy Mackay
c5851d2ddf
Copter: remove throttle rate's I and D calcs
2013-07-23 11:02:04 +09:00
Randy Mackay
740970efa6
Copter: remove stabilize's call to calc I terms
...
I terms all moved to rate controllers so this will be a small
performance improvement
2013-07-23 10:37:10 +09:00
Randy Mackay
c9a875da52
Copter: remove unused earth frame rate controllers
2013-07-21 14:08:39 +09:00
Randy Mackay
43379f20c3
Copter Motors: replace limit bitmask with structure
2013-07-21 13:58:24 +09:00
Olivier-ADLER
ac0886334d
Copter: Failsafe GCS typo in comments
...
replaced GPS by GCS word in different comments locations
2013-07-20 20:54:51 +09:00
Randy Mackay
11e7e9eaf1
Copter: WP_YAW_BEHAVIOUR param update for Look Ahead
2013-07-20 15:46:19 +09:00
Randy Mackay
c937fe45e1
Revert "Copter: Remove CH7 & CH8 Enable / Disable of GeoFence"
...
This reverts commit e25b8933f3
.
2013-07-20 15:00:08 +09:00
Randy Mackay
7ea971d948
Copter: check set_mode for failure
...
Previously if set_mode failed it would return the copter to stabilize
mode. With this commit set_mode returns a true/false indicating whether
it succeeded or not so the caller can make the decision as to the
appropriate response which could be to stay in the current flight mode
or try another flight mode.
2013-07-20 11:01:10 +09:00
Robert Lefebvre
2a9f4bbbad
TradHeli: Creating new unified roll/pitch rate controller.
2013-07-19 16:16:12 +09:00
Robert Lefebvre
23ea151ca5
TradHeli: Fix Heli rate controller filter rates.
2013-07-19 16:16:10 +09:00
Robert Lefebvre
c812d07993
TradHeli: Creating motor_runup_complete bool which is to confirm that the heli motor is running. This will be used for advanced features in the future.
2013-07-19 16:16:08 +09:00
Robert Lefebvre
b4863dc997
TradHeli: Change to throttle controller to allow swash plate collective to move, even if disarmed, if we are in Acro or Stab. This is slightly dangerous... as a user could cause a problem if they do not follow the proper usage procedures. If they do not route the ESC through the APM, but instead direct to Rx. And then if they do not Arm, they could take off in Stab mode while disarmed, but then when they switch to Alt_Hold, it will drop the collective to the bottom and they will fall. This can be saved by switching back to Stab. And it requires operation outside of the normal operating procedure.
...
This change is being made because most heli users expect to be able to check the swash plate operation before arming and taking off.
2013-07-19 16:16:04 +09:00
Robert Lefebvre
cea0812b82
TradHeli: Rate PID Improvement. Limit Integrator wind-up when PID output is saturated. Also a little bit of general clean-up for readability.
2013-07-19 16:16:01 +09:00
Craig3DR
e25b8933f3
Copter: Remove CH7 & CH8 Enable / Disable of GeoFence
2013-07-18 17:06:53 +09:00
Andrew Tridgell
0b27bb05d4
Copter: fixed FENCE and WPNAV parameter doc generation
2013-07-18 14:58:24 +10:00
Randy Mackay
41ba4a1ed2
Copter: initialise ch7 and ch8 aux switches
...
This ensures that if you have simple mode or sonar attached to an
auxiliary switch it will be enabled or disabled according to the switch
immediately after start-up
2013-07-16 22:05:59 +09:00
Randy Mackay
1dcc5886d0
Copter: ensure take-off alt is at least 1m
...
fixes issue #377
2013-07-16 15:51:18 +09:00
Randy Mackay
e6412b6996
Copter: do not spin motors during arming process
2013-07-16 12:47:57 +09:00
Jonathan Challinger
9f51a4a4f7
Copter: Cancel arming if throttle input above cruise_throttle.
2013-07-16 12:47:55 +09:00
Jonathan Challinger
2725f219cb
Copter: Warn user with motors while copter is arming
2013-07-16 12:47:51 +09:00
Randy Mackay
02b64e259d
Copter: bug fix for descent during loiter_turns
2013-07-15 20:44:56 +09:00
Andrew Tridgell
9a159a5e23
Copter: make wp_distance static
...
removed hack with AP_Camera library
2013-07-15 09:56:45 +10:00
Randy Mackay
47ab02d686
Copter: bug fix to ROI to pull target from conditional command queue
2013-07-14 17:37:06 +09:00
Randy Mackay
f1969d5662
Copter: switch from NAV_ROI to DO_SET_ROI
2013-07-14 17:37:05 +09:00
Randy Mackay
2b5f6e2668
Copter: pre-arm checks for rc ch 1~4 min and max
2013-07-13 21:38:22 +09:00
Randy Mackay
213472102c
Copter: pre-arm check of throttle failsafe value
...
Check throttle min is above throttle failsafe trigger and that trigger
is above ppm encoder's loss-of-signal value of 900
2013-07-13 20:25:34 +09:00
Randy Mackay
6bfcd28ade
Copter: thr failsafe will not RTL if in batt failsafe
...
resolves issue #413
2013-07-13 19:49:25 +09:00
Randy Mackay
5a40ee7a38
Copter: fix to gps present check in mavlink extended status 1 msg
2013-07-13 10:27:50 +09:00
Randy Mackay
66d7f7b026
Copter: GCS_mavlink only send waypoints to gcs3 if initialised
...
Also Load parameter defaults at initialisation (although defaults are
all zero anyway so should have no effect)
2013-07-13 10:12:01 +09:00
Randy Mackay
aefb38e486
Copter: remove param to disable accel based throttle controller
2013-07-12 22:57:30 +09:00
Randy Mackay
d5b4c44926
Copter: comment fix for flight mode switch delay const
2013-07-12 22:29:14 +09:00
Rayjan Wilson
07ca8ef87a
attempt to change from 1/10th second to 2/10th second on flight mode switch
2013-07-12 21:57:35 +09:00
Randy Mackay
53bff2b63e
Copter: cli to report ch8 radio values
2013-07-12 21:46:03 +09:00
Randy Mackay
2f4221391e
Copter: set_dead_zone renamed to set_default_dead_zone
...
Dead zones now set as part of rc initialisation instead of only after
eeprom is erased.
Change in use of parameter means value passed in should be 1/2 what it
was previously
2013-07-12 11:44:23 +09:00
Randy Mackay
1685ff274d
TradHeli: compile error fix related to new ACRO
...
The motors_runup_complete must be a feature that Rob has implemented in
his clone which has not yet reached master. We will need to restore
these lost few trad-heli specific lines once Rob's changes make it to
master.
2013-07-11 22:33:55 +09:00
Leonard Hall
64ce9b017d
Copter: Body frame ACRO upgrade
2013-07-11 17:53:25 +09:00
Randy Mackay
6dd446ac79
Copter: firmware version to 3.0.1
2013-07-11 16:45:05 +09:00
Andrew Tridgell
5ae62f4f04
Copter: fixed build with specified GPS driver
2013-07-11 14:27:42 +10:00
Randy Mackay
ac5d925115
Copter: revert Loiter Pos P to 1.0 (was 0.8)
2013-07-11 12:20:31 +09:00
Randy Mackay
1590a5d58a
Copter: increase Yaw Rate I 0.02
2013-07-11 12:20:29 +09:00
Randy Mackay
ab1a7baf71
Copter: project stopping point for loiter command
2013-07-11 11:39:47 +09:00
Randy Mackay
d77f7bc803
Copter: default Loiter Pos P to 0.8 (was 0.2)
2013-07-11 08:13:17 +09:00
Randy Mackay
ec65764750
Copter: typo in release notes
2013-07-11 08:04:45 +09:00
Randy Mackay
ab09dc46fb
Copter: update release notes
2013-07-10 21:20:01 +09:00
Randy Mackay
345924ddec
WPNav: replace LOITER_ACCEL_MAX with parameter
...
Also removed unused _lean_angle_max variable
2013-07-10 20:00:32 +09:00
Randy Mackay
8cb7bd628e
Copter: change firmware version to 3.0.1-rc2
2013-07-10 15:52:21 +09:00
Randy Mackay
f459d35e3e
Copter: roll-pitch fix to allow I to reduce
...
Contributed by Leonard Hall
2013-07-10 15:52:15 +09:00
Andrew Tridgell
da4137b731
Copter: changes for GPS field changes
2013-07-10 14:04:22 +10:00
Andrew Tridgell
c544a076ca
Copter: enable camera logging by default
...
these messages only happen on user defined camera triggering, so
should be low rate
2013-07-10 12:24:02 +10:00
Craig@3DR
bbd4fbd2fb
Copter: trigger + logging on camera update_location()
2013-07-10 08:39:59 +10:00
Tobias
cf426fcb3e
Copter: fixed a compiler warning
...
* removed useless comparison: if (int8_t t >= 255) ...
* revealed by -Wtype-limits
* saved 6 bytes
2013-07-08 14:53:30 +10:00
Randy Mackay
ed3bf2c1e7
Copter: relax pre-arm checks for mag field
...
previously it was 50% ~ 150% of expected mag field but now expanded to
35% ~ 165%.
2013-07-07 18:00:36 -10:00
tobias
4e73cf810e
Copter: added cast to remove compiler warning
2013-07-08 12:07:50 +10:00
Randy Mackay
45f47de98d
Copter: reduce default Loiter Pos P to 0.2 (was 1.0)
2013-07-07 16:00:09 -10:00
Randy Mackay
9361e9fe32
Coper: compile error fix when FENCE disabled
2013-07-05 17:22:05 -10:00
Randy Mackay
227185fd0f
Copter: remove constraint on rate yaw controller
2013-07-05 14:18:58 -10:00
Randy Mackay
40612ed551
Copter: yaw limit fix to allow I to reduce
...
We now allow the I term even if we've hit the yaw limits as long as
updating the I term will reduce it
2013-07-05 13:52:03 -10:00
Randy Mackay
0cf4ac088a
Copter: restore LEDs to off state when auto-trim completes
2013-07-04 16:38:28 -10:00
Randy Mackay
79d2fe6271
Copter: double flash arming light when pre-arm checks fail
...
Hardly my finest work but it's temporary because we're going to replace
all the led, buzzer etc with a library called AP_Notify in the near
future.
2013-07-04 16:26:22 -10:00
tstellanova
459c47fa46
Fix test_ins
...
Fix output format of test_ins and fix the number of parameters passed
to printf
2013-07-02 23:42:48 -10:00
Randy Mackay
404cd5f3da
Copter: rename g.pid_throttle to g.pid_throttle_rate
...
Small code clean-up to make throttle rate controller's pid more obvious
2013-06-30 00:04:21 -10:00
Randy Mackay
b3da8a462f
Copter: CH6 tuning definition clean-up
...
Renamed and reorganised the CH6 #defines and parameter definitions
2013-06-29 23:51:43 -10:00
Dr Gareth Owen
e0dcd680f7
proposed radio failsafe bug fix
2013-06-27 17:13:01 -10:00
Randy Mackay
917ae883a0
Copter: revert prev changes to battery failsafe
...
The battery failsafe should remain independent of any throttle failsafe
behaviour settings
2013-06-27 10:30:46 -10:00
Robert Gayle
917edcab11
Copter: added FS_THR_ENABLED_ALWAYS_LAND (=3) option: don't attempt RTL, just land
2013-06-27 10:19:38 -10:00
Olivier-ADLER
eaa0e36954
Copter: CompassMot current calibration
...
Was using a hardcoded (330) value instead of COMPASS_MAGFIELD_EXPECTED define
2013-06-26 20:54:03 -10:00
Jonathan Challinger
b21bc5a85a
Copter: Fixed bug in battery current integration
2013-06-26 17:22:37 +09:00
Randy Mackay
0592475959
Copter: change firmware version to 3.0.0-rc1
2013-06-26 14:03:28 +09:00
Randy Mackay
cb0e262e24
Copter: GPS Failsafe switch to LAND if circular fence enabled
2013-06-26 11:57:59 +09:00
Randy Mackay
45dfbecaba
Copter: update 3.0.1 version and release notes
2013-06-26 00:09:36 +09:00
Randy Mackay
022148ec0d
Copter: LAND only control horizontal position if we have GPS lock
2013-06-25 22:34:58 +09:00
Randy Mackay
66cecbfdc3
Copter Fence: bug fix to avoid repeatedly invoking LAND mode
2013-06-25 22:23:31 +09:00
Olivier-ADLER
24e1f074d0
Copter: Fence missing GPS 3D fix check
...
Fence was missing GPS 3D fix check before selecting recovery decision.
2013-06-25 22:23:29 +09:00
Randy Mackay
facd8fc89f
Copter: calculate home position and bearing when we have 2D Fix
2013-06-25 22:23:26 +09:00
Olivier-ADLER
f1bedc70ac
Copter: SuperSimple mode bug
...
SuperSimple bearing was updated without checking for GPS 3D Fix availability.
2013-06-25 22:23:13 +09:00
Andrew Tridgell
3e82f644ea
Copter: enabled CAM_TRIGG_DIST parameter
2013-06-25 12:52:44 +10:00
Andrew Tridgell
76d1791073
Copter: CONFIG_RELAY is not used
2013-06-25 12:47:07 +10:00
Andrew Tridgell
23eade8f74
Copter: enable RELAY_* parameters
2013-06-25 12:46:53 +10:00
Randy Mackay
a48a7f9775
Copter: minor param definition unit changes
2013-06-23 15:52:46 +09:00
Randy Mackay
cd30103b76
Copter: increase default CIRCLE_RATE to 20deg/sec
2013-06-19 12:40:33 +09:00
Randy Mackay
245bc3d3fd
Copter: show pilot input in dataflash ATT message even when in AUTO
...
AUTO mode ignores pilot input but we still want to be able to see the
pilot's input in the Roll-In and Pitch-In columns of the dataflash's ATT
message
2013-06-19 12:37:13 +09:00
Randy Mackay
acb4907313
Copter: update FS_THR_VALUE parameter description
...
One user was setting FS_THR_VALUE too low, below 900 which means
ArduCopter would not trigger when the ppmencoder pulled ch3 low after
updates from the ppmencoder stopped
2013-06-18 15:56:39 +09:00
Randy Mackay
b1a014e12e
Copter: update firmware version to 3.0.0
2013-06-18 10:03:40 +09:00
Randy Mackay
c42ed1e5eb
Copter: add @Increment to PID parameters descriptions
2013-06-16 21:53:50 +09:00