Randy Mackay
597a4b912a
Copter: fix to allow building HIL_MODE_SENSORS
2013-03-18 13:41:52 +09:00
Randy Mackay
d1344e8c39
Copter: remove #define for CROSSTRACK_GAIN
...
Note: the cross track is still calculated inside the inertial nav based
loiter and wp controls but it's no longer requires a tunable parameter
2013-03-17 16:56:18 +09:00
Randy Mackay
1b6fcad90a
Copter: remove tilt compensation parameter
...
Note: this idea of feed forward tilt compensation is being incorporated
into the inertial nav based loiter and wp controllers but does not
require a separate tunable parameter
2013-03-17 16:53:32 +09:00
Randy Mackay
fdcb78ccf7
Copter: leonard's smoother alt-hold transition
...
Target altitude when entering alt-hold is based on a projection from
current alt and climb rate
2013-03-17 13:24:49 +09:00
Randy Mackay
150046f2b8
Copter: GPS Failsafe implemented
...
Switches to LAND mode 5 seconds after losing GPS if you're in a flight
mode that requires a GPS
2013-03-16 17:27:46 +09:00
Randy Mackay
a73f50494c
TradHeli: remove duplicate RC_FAST_SPEED definition
2013-03-04 23:45:23 +09:00
Randy Mackay
33bd984a91
Copter: remove unused input_voltage parameter
2013-03-03 23:23:54 +09:00
Randy Mackay
d6ff5ae261
Copter: add roll-pitch slew for auto modes
...
Added reporting of roll, pitch inputs for ACRO, AUTO
2013-02-24 14:42:04 +09:00
Randy Mackay
e297ba7d18
Copter: update default loiter gains for inertial nav
2013-02-24 14:42:00 +09:00
Randy Mackay
cbde042ec5
Copter: remove non-inav loiter and wp controllers
...
lon_speed, lat_speed changed to float
do_takeoff, do_land now set roll-pitch, yaw and nav modes specifically
removed fast_corners functionality (may need to be reimplemented with
new inertial nav controllers)
2013-02-24 14:41:52 +09:00
Randy Mackay
609676e26c
Copter: add logging of compass values
...
Removed rarely used ITERM because we didn't have enough bits in the log
mask
2013-02-24 14:41:48 +09:00
Randy Mackay
67c69a19ee
Copter: remove baro-only alt hold
...
Saves 8 bytes of memory and more importantly simplifies the alt hold
calculations
2013-02-24 14:41:29 +09:00
Randy Mackay
fcf102b2cf
Copter: inertial nav waypoint controller
...
#define added to allow compile time selection of traditional or inav
based loiter and wp controllers
2013-02-24 14:41:09 +09:00
Randy Mackay
8e4c9518ea
Copter: increase low voltage check to 10.5v
...
Change requested by Rob Lefebvre and Richie Wilson
2013-02-23 00:36:51 +09:00
Andrew Tridgell
4c7a1a1806
Copter: change PX4 main baud rate back to 115200
...
we now use USB console
2013-02-22 07:04:23 +11:00
Randy Mackay
06a71af12f
Copter: THR_MID used to scale manual throttle
2013-02-01 22:37:16 +09:00
Randy Mackay
ce370bab0c
Copter: rename CUR and CURR to CURRENT for logging
...
Based on user complaint that enable/disable was using CUR while message
was appearing as CURR
2013-01-26 17:20:41 +09:00
Randy Mackay
b74fe10aa9
Copter: set each flight mode's nav_mode
...
Allow ACRO flight mode's roll, pitch, yaw, throttle and nav mode to be
overwritten
2013-01-25 15:57:55 +09:00
Andrew Tridgell
f303554259
Copter: run serial0 at 57600 on PX4
2013-01-22 09:50:22 +11:00
Robert Lefebvre
dde713aaa5
Arducopter: Backing out my changes for a new Loiter Repositioning mode. Leonard and Jonathan's work will trump this.
2013-01-20 21:32:00 +09:00
Andrew Tridgell
580abf1106
Copter: fixed PX4 mag orientation
2013-01-17 17:23:34 +11:00
James Bielman
5631f865b2
Update floating point calculations to use floats instead of doubles.
...
- Allows use of hardware floating point on the Cortex-M4.
- Added "f" suffix to floating point literals.
- Call floating point versions of stdlib math functions.
2013-01-16 13:52:01 +11:00
Randy Mackay
fef7569dee
Copter: added experimental LOITER_REPOSITIONING #define to config.h
...
APM_Config.h should be used to overriding the standard parameters but
they still require a definition in config.h or they will be undefined
when built by the mission planner.
2013-01-14 13:34:14 +09:00
Randy Mackay
9ad6f711f8
ArduCopter: replace FS_THR_RTL_MIN_DISTANCE with wp_radius
...
This effectively means that an RTL kicked off by a failsafe will
immediately switch to LAND mode only if within 2 meters. Previously the
radius was much wider (15m).
2013-01-13 20:00:47 +11:00
Randy Mackay
12f885c33c
ArduCopter: disable ITERM logging by default
...
This message takes 1ms to write and we are running over our limits on
some loops.
2013-01-13 20:00:39 +11:00
rmackay9
21b6c78d12
ArduCopter: added get_throttle_althold_with_slew to allow slower altitude target changes
...
Improved surface tracking by using slewed althold controller
Reduced sonar mode filter to just 3 elements to reduce lag but at the possible consequence of allowing sonar noise to creep through for people with margin sonar set-ups.
2013-01-13 19:51:47 +11:00
Randy Mackay
87627d883b
ArduCopter: use new logging method for remaining packet types
...
Additional changes include renaming RAW dataflash type to IMU
2013-01-13 00:17:44 +09:00
James Bielman
7827a4a54a
ArduCopter: Add AP_HAL_SMACCM support.
...
- Added default configuration to "config.h".
- Added main function to run under FreeRTOS with HWF4.
2013-01-09 11:19:51 -08:00
James Bielman
ab37f833db
MS5611: Fix CONFIG_MS5611_SERIAL definitions.
...
- Make sure the values are defined as integers. We were always using
SPI rather than using I2C when desired.
2013-01-09 11:19:51 -08:00
Andrew Tridgell
c48714be16
Copter: enabled PX4 sensors
2013-01-05 20:39:31 +11:00
James Bielman
264db3670e
AP_Baro: Add CONFIG_MS5611_SERIAL option to choose between SPI and I2C.
...
- Update ArduCopter and ArduPlane modules to pass the correct serial
driver to the MS5611 driver.
- Update barometer examples, assuming SPI.
2013-01-03 13:48:06 -08:00
Andrew Tridgell
94e3322e24
Copter: fixed build on px4
2013-01-02 22:09:02 +11:00
rmackay9
9b2956b377
ArduCopter: increase throttle rate P to 6.0 (was 1.0) and alt hold P to 2.0 (was 1.0)
2013-01-02 09:55:37 +11:00
rmackay9
d400e5040b
ArduCopter: turn on INERTIAL_NAV_Z in the config.h file so that it takes effect when built for the mission planner
2013-01-02 09:55:37 +11:00
rmackay9
e850ab7ccd
ArduCopter: add AUTO_VELZ_MIN, AUTO_VELZ_MAX and PILOT_VELZ_MAX to allow better control of climb/descent rate in auto and manual throttle modes
2013-01-02 09:24:31 +11:00
rmackay9
5526ca204c
ArduCopter: on throttle failsafe, only initiate RTL if we are at least 15m from home
2013-01-02 09:22:51 +11:00
Robert Lefebvre
6e64b1b357
ACM: Precision Loiter RePositioning code.
...
Protected behind a #define
2013-01-02 09:19:39 +11:00
rmackay9
e6519330f4
ArduCopter: remove unused rc_override variables to save 21 bytes
2013-01-02 09:19:17 +11:00
rmackay9
34e18ae12a
ArduCopter: increase accel based throttle PIDs and add D term to rate based throttle
2013-01-02 09:19:17 +11:00
Robert Lefebvre
9605bd8ee1
ACM: Trying to set a default MPU6K filter rate of 10Hz for TradHeli. Doesn't Work.
2013-01-02 09:14:55 +11:00
rmackay9
d8e3d5c10c
ArduCopter: allow RTL's yaw mode to be overridden with a #define in APM_Config.h
2013-01-02 09:12:40 +11:00
rmackay9
50d46898fb
ArduCopter: allow GUIDED mode roll-pitch, yaw and throttle control modes to be overridden
2013-01-02 09:12:17 +11:00
Andrew Tridgell
9e986801c9
Copter: fixed SITL for ArduCopter
2012-12-20 14:52:34 +11:00
Pat Hickey
5e63491994
ArduCopter: fix issues with HAL/HIL mixup and baro/compass instances
2012-12-20 14:52:29 +11:00
Pat Hickey
d93d932831
ArduCopter: defines fixes
...
Conflicts:
libraries/AP_Common/Arduino.mk
2012-12-20 14:52:28 +11:00
Pat Hickey
2aa4657315
ArduCopter: changes to use CONFIG_HIL_BOARD
2012-12-20 14:52:28 +11:00
rmackay9
2f748f8382
ArduCopter: renamed BATT_FAILSAFE to FS_BATT_ENABLE
2012-12-10 23:47:14 +09:00
rmackay9
d31efebd44
ArduCopter: rename throttle failsafe parameters.
...
Switch to LAND flight mode if throttle failsafe triggers and we do not have a GPS.
THR_FAILSAFE renamed to FS_THR_ENABLE.
THR_FS_VALUE renamed to FS_THR_VALUE.
THR_FS_ACTION removed (action is now controlled by setting FS_THR parameter).
2012-12-10 23:38:43 +09:00
rmackay9
2f1b2b70e6
ArduCopter: added ACRO_TRAINER parameter to allow enabling/disabling the acro training function which will bring the roll back to within +- 45 degrees
2012-12-10 22:27:46 +09:00
rmackay9
dadad8677e
ArduCopter: added descriptions for most parameters that did not have them
...
Renamed loiter_radius to circle_radius to better reflect it's purpose.
Removed some unused parameters including WP_MODE, WP_MUST_INDEX, LOG_LASTFILE, AXIS_P
2012-12-10 21:45:57 +09:00
rmackay9
cfe2507c0b
ArduCopter: reduce Rate Roll/Pitch P to 0.150 (was 0.175) and increase I to 0.1 (was 0.01)
2012-12-09 18:08:45 +09:00
Robert Lefebvre
aa4d4f8c24
ACM: Adding Pre-Compiler Define for Stabilize Throttle Mode.
2012-12-08 20:41:05 -05:00
Robert Lefebvre
1b97a92098
ACM: Code Cleanup
2012-12-08 14:49:38 -05:00
rmackay9
f98a807d36
ArduCopter: remove debug related to yaw mode used for alt hold
2012-12-08 14:24:50 +09:00
rmackay9
9dd978576b
ArduCopter: auto yaw changes to allow pilot override of yaw during missions
...
Added set_yaw_mode to better control of yaw controller changes and variable initialisation.
Replaced AUTO_YAW mode with separate yaw controllers YAW_LOOK_AT_NEXT_WP, YAW_LOOK_AT_LOCATION, YAW_LOOK_AT_HEADING.
Pilot manual override of yaw causes yaw to change to YAW_HOLD (i.e. manual yaw) until next waypoint is reached.
Added get_yaw_slew function to control how quickly autopilot turns copter
Changed YAW_LOOK_AHEAD to use GPS heading and moved to new get_look_ahead_yaw function in Attitude.pde
Renamed variables: target_bearing->wp_bearing, original_target_bearing->original_wp_bearing.
Removed auto_yaw_tracking and auto_yaw variables and update_auto_yaw function as they are no longer needed.
Simplified MAV_CMD_CONDITION_YAW handling (do_yaw). We lose ability to control direction of turn and ability to do long panorama shots but it now works between waypoints and save 20bytes.
2012-12-08 14:23:32 +09:00
rmackay9
68ca123224
ArduCopter: remove some unused #defines
2012-12-07 15:17:35 +09:00
rmackay9
3a90fc77f9
ArduCopter: add dataflash logging of camera events
2012-12-07 00:57:08 +09:00
rmackay9
a5bb54e36e
ArduCopter: RTL clean-up and slightly improved landing sensor
...
Consolidated RTL state to be captured by rtl_state variable.
Combined update_RTL_Nav and verify_RTL functions which performed the same function but one was for missions, the other for the RTL flight mode.
Renamed some RTL parameters and global variables to have RTL at the front.
Landing detector now checks accel-throttle's I term and/or a very low throttle value
2012-12-06 10:31:52 +09:00
rmackay9
072ffec493
ArduCopter: allow INERTIAL_NAV to be enabled separately for horizontal and vertical position
2012-12-06 10:31:41 +09:00
rmackay9
bdb47c449a
ArduCopter: pass linear altitude error to throttle rate controllers.
...
Previously the requested rate used the square root of the altitude error.
Scale pilot's desired vertical rate and acceleration based on ACCELERATION_MAX_Z and VELOCITY_MAX_Z #defines
2012-12-06 10:31:31 +09:00
rmackay9
7b4ed2d227
ArduCopter: restored landing detector to landing throttle mode.
...
Added LAND_SPEED parameter to control the rate of descent for the last 10m of a landing.
Added CH6 tuning for accel based throttle controller.
2012-12-06 10:31:20 +09:00
rmackay9
560bb1d738
ArduCopter: removed unused AUTO_THROTTLE_HOLD #define
2012-12-06 10:31:15 +09:00
rmackay9
3cbef57c64
ArduCopter: first merge of leonard's accel based altitude controller plus other changes from Randy
...
Changes include:
New low-level get_throttle_accel function takes target acceleration and compares vs earth-frame Z accelerometer values to produce output to motors.
Higher level throttle controllers modified to call new get_throttle_accel controller
Throttle_rate_stabilized controller added which maintains a desired climb/descent rate
Throttle_land controller added - descends using normal auto throttle controller to 10m then descends at 50cm/s
Multiple throttle modes added including landing mode
Land flight mode no longer needs GPS
Throttle cruise maintenance moved to update_throttle_cruise function
2012-12-06 10:30:49 +09:00
Andrew Tridgell
6fbf5ec8f2
Copter: update ArduCopter for new ins interface
2012-11-30 07:15:18 +11:00
Robert Lefebvre
6b8c39dd10
ACM: Creating Yaw_Look_Ahead yaw mode.
...
This function is not fully tested yet.
2012-11-26 21:37:13 -05:00
Robert Lefebvre
6ffc115236
Changes to get_throttle_rate()
...
Commented out a bit of code that is not used currently
Change the output constrains to #defines so they can be easily changed, particularly for use in TradHeli.
2012-11-21 17:11:38 -05:00
Andrew Tridgell
dafaa2efc8
SITL: disable optical flow on the desktop build
...
it doesn't work yet, as no sensor emulator is available
2012-11-19 09:04:03 +11:00
rmackay9
07a7a1acd8
ArduCopter: replaced digitalRead and digitalWrite with faster calls
...
improved performance logging to dataflash
2012-11-19 01:16:07 +09:00
rmackay9
e92b560df5
ArduCopter: low baterry failsafe
2012-11-15 23:35:41 +09:00
Jason Short
9735a0eff1
ACM: Allow for user defined roll and pitch input max
2012-11-11 18:00:10 -08:00
rmackay9
e212744f4c
ArduCopter: failsafe improvements
...
resolves momentary throttle drop to zero before failsafe engages
resolves motor cut after 30seconds if flying in stabilize without GPS (now switches to ALT_HOLD with target altitude zero)
disables motors if throttle was zero before failsafe event
2012-11-11 22:11:12 +09:00
Jason Short
129ec35c35
ACM crosstrack min distance
2012-11-09 22:15:16 -08:00
Jason Short
4d7b9137fe
ACM: Added max RTL altitude
2012-11-09 22:15:15 -08:00
rmackay9
1f801714e8
ArduCopter: incorporate new version of inertial navigation
...
Moved several navigation functions from ArduCopter.pde to navigation.pde
2012-11-07 19:21:31 +09:00
Jason Short
73bc90f9b8
ACM: config.h cleanup
...
Added LOG_ITERM default to enabled
2012-10-27 09:59:57 -07:00
rmackay9
5e8043fd9c
ArduCopter: changed ACRO_ROLL_STABILIZE and ACRO_PITCH_STABILIZE to parameters
...
Changes on behalf of Leonard Hall
2012-10-23 21:30:50 +09:00
rmackay9
78316adf75
ArduCopter: replace Serial.print with Serial.print_P to save memory.
...
Includes replacing flight_mode_strings with print_flight_mode function.
SendDebug macro replaced with direct Serial.print_P calls.
2012-10-22 16:45:24 +09:00
Robert Lefebvre
bfade7d0ed
Fixed that last commit
...
#define Stupid_Mistake
2012-10-18 16:50:42 -04:00
Robert Lefebvre
592f4040fd
Changed RLT Yaw Mode for TradHeli. Also a few comment cleanups.
2012-10-18 16:39:05 -04:00
rmackay9
583f2e49a3
ArduCopter: integrated Leonard Hall's improved ACRO mode
2012-10-18 23:24:34 +09:00
rmackay9
7d7de976c3
ArduCopter: reduced optical flow's I and IMAX terms
2012-10-17 17:47:43 +09:00
LeonardTHall
d7b7e1cefa
New Yaw controller using rate feed forward and stabilize.
...
Signed-off-by: LeonardTHall <LeonardTHall@gmail.com>
2012-10-15 11:37:49 +09:00
rmackay9
ee5dab9647
ArduCopter: enable ACRO mode's AXIS_LOCK by default
2012-10-14 19:50:45 +09:00
rmackay9
997fe85880
ArduCopter: fixed acro mode
...
Changes included:
Removing earth frame roll_rate_trim, pitch_rate_trim and yaw_rate_trim.
Switch ACRO mode to use YAW_ACRO instead of YAW_HOLD.
Changed YAW_ACRO to use stabilize yaw when axis_enabled.
Reset ACRO roll, pitch and yaw targets to current attitude when first entering ACRO.
2012-10-14 17:47:46 +09:00
rmackay9
4a41a3d210
ArduCopter: added BATT_VOLT_PIN and BATT_CURR_PIN parameters to allow support for new 3DR IV battery voltage and current monitor
2012-10-13 18:40:46 +09:00
Robert Lefebvre
dae81d2068
Added #define for Tilt_Compensation.
...
Also added some detail to WP_Speed_Max parameter.
2012-10-12 14:51:31 -04:00
rmackay9
03933df5b7
ArduCopter: set default rate roll and pitch I terms to 0.010, and rate yaw to 0.015
...
Updated after discussing with Marco
2012-10-11 17:25:01 +09:00
rmackay9
35fa50234f
ArduCopter: move I terms from stabilize to rate controllers
2012-10-11 17:20:05 +09:00
rmackay9
af1d6a9b82
ArduCopter: reduce Stabilize Yaw P term to 4.5
2012-10-03 14:19:49 +09:00
rmackay9
ea4f256f8e
ArduCopter: BATT_PIN parameter added to allow you to select which pin is used for voltage and current measurements
...
To save a parameter, the current sensor pin is assumed to always be 1 higher than the voltage pin.
2012-10-02 22:16:19 +09:00
rmackay9
95763e610b
ArduCopter: allow DMP to run in parallel with DCM
...
Parallel DMP can be enabled by #define SECONDARY_DMP_ENABLED in APM_Config.h
New DMP dataflash log type added to allow easy comparison with DCM
2012-09-30 00:25:40 +09:00
rmackay9
41fbb19cf5
AP_InertialSensor_MPU6000: replaced _cs_pin parameter with #define and saved 1 byte of memory
...
Updated ArduCopter, ArduPlane and example sketches in AP_InertialSensor, AP_IMU and AP_AHRS libraries because they no longer need to pass in cs_pin to the constructor
2012-09-28 19:21:59 +09:00
rmackay9
fff5d51694
ArduCopter: reduced Loiter Rate I to 0.04 (was 0.08)
2012-09-25 19:08:31 +09:00
rmackay9
a71aa21514
ArduCopter: increase default Loiter Rate P to 5.0
2012-09-25 12:19:44 +09:00
rmackay9
9e66b555cb
ArduCopter: removed INSTANT_PWM from ArduCopter and AP_Motors library
2012-09-13 21:31:13 +09:00
rmackay9
42406c827a
ArduCopter: added NUM_IMU_SAMPLES_FOR_XYZHZ definitions for MPU6000 and Oilpan to allow more syncing of the mainloop with the arrival of data from the IMU.
2012-09-10 11:37:48 +09:00
Craig Elder
274b2e2143
Arducopter: Release 2.7.2
2012-08-31 19:18:10 -07:00
Andrew Tridgell
e8d928cca4
ACM: added TELEM_DELAY to ArduCopter
2012-08-30 09:03:01 +10:00
Craig Elder
4ad516c445
Arducopter: increased MAVLINK delay to 6s to reduce the chance of xBee bricking
...
Arduplane: increased MAVLINK delay to 6s to reduce the chance of xBee bricking
Ardurover: increased MAVLINK delay to 6s to reduce the chance of xBee bricking
2012-08-28 20:09:10 -07:00
rmackay9
2ad6dcb7c4
ArduCopter: increased Stabilize Roll and Pitch I term to 0.05 (was 0.01) based on feedback from Jason
2012-08-29 11:34:53 +09:00
rmackay9
b4b394e67e
ArduCopter: reduced Rate Roll and Pitch PID values
...
RATE_ROLL_P, RATE_PITCH_P reduced to 0.165 (was 0.185)
RATE_ROLL_D, RATE_PITCH_D reduced to 0.004 (was 0.008)
2012-08-26 10:45:45 +09:00
uncrustify
429c41155c
uncrustify ArduCopter/config.h
2012-08-21 19:19:50 -07:00
Andrew Tridgell
6d11940ada
AHRS: removed Quaternion build support from APM/ACM/rover
2012-08-22 10:42:21 +10:00
rmackay9
1d32e03f61
ArduCopter: added ACCEL_ALT_HOLD and INERTIAL_NAV to config.h and commented out of APM_Config.h.
...
Reduces possibility of difference between arduino ide compiled code and script built code (i.e. autotester, mission planner)
2012-08-19 12:31:02 +09:00
Jason Short
3ee2fd3fb6
ACM: Config.h - added default for toy mixer
2012-08-16 15:40:28 -07:00
Jason Short
9a568385b0
ACM increase the minimum speed at WP
2012-08-10 10:01:40 -07:00
Jason Short
3e57f8afd8
ACM: config.h = updated default gains
...
More yaw rate control
2012-08-09 16:59:43 -07:00
Amilcar Lucas
d34549f386
Add an optional second mount to ArduPlane and ArduCopter
2012-08-08 23:22:24 +02:00
Amilcar Lucas
9cc705939a
Add a second mount instance
2012-08-08 23:07:25 +02:00
Amilcar Lucas
aa3cc63b15
ArduCopter: Make the code fit in a 1280 chip again
...
Even allows to control a camera/antenna mount, if the user explicitly wants to.
2012-08-06 00:23:48 +02:00
Amilcar Lucas
0106c133cf
Default CLI_SLIDER_ENABLED to DISABLED
...
Chris asked for this on the mailing list
2012-08-06 00:22:33 +02:00
Amilcar Lucas
afd96025a7
ArduCopter: Save more space in APM1280
2012-08-05 23:05:52 +02:00
Amilcar Lucas
d29f7023cc
Merge from ArduPlane
2012-08-04 18:38:50 +02:00
rmackay9
77b1785bc6
ArduCopter: reduce stabilize roll, pitch and rate yaw IMAX values
2012-07-30 11:01:45 +09:00
rmackay9
014f5aae99
ArduCopter: added DMP_ENABLE #define and CH6 tuning value for AHRS_KP
2012-07-28 14:21:07 +09:00
Jason Short
96aabb7712
ACM: Lowered default Alt hold P
2012-07-21 16:45:00 -07:00
Jason Short
3b496ff229
Arducopter: Upped D rate to .005 by default
2012-07-19 22:35:21 -07:00
Jason Short
49c7579079
Arducopter: Config.h defaults adjustments
2012-07-19 17:48:48 -07:00
Jason Short
3401bd3583
Arducopter: Clarified units in comment
2012-07-19 09:49:13 -07:00
Jason Short
dcf9f9dab1
Arducopter
...
for rate altitude changes
2012-07-18 22:57:10 -07:00
Andreas M. Antonopoulos
a976a59c88
AP_Limits: Configuration defaults moved to config.h. Fixed AP_LIMITS==DISABLED handling.
2012-07-16 11:46:43 -07:00
rmackay9
36ecdff593
ArduCopter: removed unused config for CAM_ROLL_GAIN and CAM_ROLL_PITCH now in AP_Mount library)
2012-07-15 16:38:52 +09:00
Jason Short
7a5544051d
Arducopter
...
Lowered WP speed default to 500. 600 was quite high once the nav routines were fixed and quad could achieve that speed.
2012-07-11 17:46:07 -07:00
Jason Short
c04bff67de
Arducopter: Config.h, default gain tweaks from flight tests.
2012-07-10 21:53:38 -07:00
Amilcar Lucas
dfe0983e1e
Merge the changes from APM_Camera branch into ArduCopter
...
Conflicts:
ArduCopter/Camera.pde
ArduCopter/Parameters.pde
2012-07-11 00:39:13 +02:00
Jason Short
038116f521
Airspeed patch:
...
pre-calculated airspeed resistance pitches copter automatically to gain a certain speed allowing the speed controller to work off of a better set point - similar to Alt hold.
added param tilt_comp with a default of 54 which equals 19.5° of pitch to go 6m/s
upped Z and Y target speeds to int32_t for speed squared calculation
2012-07-09 13:13:32 -07:00
Andrew Tridgell
60caaa4b04
MAVLink: remove MAVLink 0.9 protocol support
...
this simplifies the code a lot. We're not going back to 1.0
2012-07-05 13:00:46 +10:00
Adam M Rivera
6e93ab6af6
Parameters: Added flag for camera pitch/roll servos (continuous or regular)
2012-07-04 21:06:21 -05:00
Jason Short
37685756df
Config.h:
...
decreased alt hold_P to .4
removed RTL_AUTO_LAND default
increased alt hold I
2012-07-03 17:37:37 -07:00
Jason Short
2d572461ec
Config: increased WP distance to 2m but default, removed alt hold D: causing issues with APM1 noise.
2012-07-03 17:18:33 -07:00
Jason Short
8a08a74cc6
Config.h : shortening the landing time to 10s
2012-07-02 17:52:38 -07:00
Jason Short
8ab1acfb92
Config.h
...
Removed Approach delay redundancy - using land timer instead
Removed Retro loiter mode param
2012-07-01 13:40:11 -07:00
rmackay9
78fa903e17
ArduCopter: updated STABILIZE_ROLL_I to 0.01 (was 0.1) as instructed by Marco
2012-06-30 19:26:14 +09:00
Jason Short
4450d80ea3
Config.h: Optimizing Nav gains
2012-06-29 21:20:28 -07:00
Jason Short
c76ac4543b
Added user editable define for Super simple radius
2012-06-26 10:38:46 -07:00
Jason Short
a0dc1f7ab1
Config.h : New Gains based on testing, new Crosstrack gain. from 1.0 to .2 because of new algorithm
2012-06-25 23:06:28 -07:00
Jason Short
7e0708ca36
Config.h - returned low to original 120
2012-06-20 15:22:35 -07:00
Jason Short
4f18e7f80b
lowered minimum throttle
2012-06-20 08:47:47 -07:00
Jason Short
39a253a273
decreased I term based on the tests last weekend in high winds
2012-06-20 08:47:47 -07:00
rmackay9
65050775e1
ArduCopter: made Robert's new yaw method optional (off by default).
...
Add this line to APM_Config.h to enable Robert's yaw
#define ALTERNATIVE_YAW_MODE ENABLED
2012-06-13 21:50:16 +09:00
Jason Short
ff0659535e
Raised the Max throttle to 1000, min to 200. Worked good in SIM with Tridge's motor safety patch.
2012-06-12 13:58:49 -07:00
rmackay9
c6f1d93849
ArduCopter: updated standard loiter pids.
...
Loiter_P (speed from distance to target) = 0.2 (was 0.35)
Loiter_Rate_P (lean angle from desired acceleration) = 2.4 (was 2.5)
Loiter_Rate_I = unchanged at 0.08
Loiter_Rate_D = 0.40 (was 0.45)
2012-06-12 20:56:31 +09:00
Jason Short
a9610a0761
Stabilization patches
...
removed Angle error limit for stabilization
constricted Iterm to +- 5° error and limited the implementation to when the quad is +- 5° from center
doubled the output limit for Rate controller.
increased default Rate_P gain to .18 with matching Rate_D of .004
Tested in the SIM and in backyard. dramatically increases performance and quad no longer overshoots and flips when pushed hard.
2012-06-05 16:41:44 -07:00
Michael Oborne
a71ed6c5ce
enable mavlink10 by default
2012-06-04 08:02:08 +08:00
Jason Short
9310d613e1
Lowered I term - causes oscillations in SIM
2012-05-29 12:43:01 -07:00
Jason Short
7f3e142fa8
Loiter Gains based on new SIM
2012-05-15 22:01:01 -07:00
Robert Lefebvre
c8fb9a6635
More CopterLEDS changes.
...
Merged CopterLEDS and Piezo functions to eliminate pin conflict on APM2. Created new Parameter bit to turn piezo function on and off from MP. Moved GPS and Aux pin assignments to allow commonality between APM1 and 2. Set LED_Mode parameter default to 9 in order to make CopterLEDS completely backwards compatible with old Motor LEDS and Piezo code. Legacy users should see no difference.
2012-05-15 12:00:21 -04:00
Robert Lefebvre
a285e2779f
CopterLEDS changes for APM2
2012-05-15 10:07:03 -04:00
Adam M Rivera
8e580729b7
config.h: Removed comment.
2012-04-23 00:16:41 -05:00
Adam M Rivera
97040a7b3a
Merge branch 'master' of https://code.google.com/p/ardupilot-mega into auto-approach
2012-04-23 00:03:37 -05:00
rmackay9
090f5aaa6f
ArduCopter - config.h - set standard RC_SPEED to 125 for helicopter frame
2012-04-21 23:46:36 +09:00
rmackay9
919f004b27
ArduCopter - changed Optical Flow for APM2 to use A3 pin
2012-04-21 20:15:16 +09:00
Adam M Rivera
c233defbe6
Merge branch 'retro-loiter' of https://code.google.com/r/a432511-wip into auto-approach
...
Conflicts:
Tools/ArdupilotMegaPlanner/Common.cs
2012-04-19 11:08:34 -05:00
Adam M Rivera
24363ccb83
Merge branch 'master' of https://code.google.com/p/ardupilot-mega into retro-loiter
2012-04-19 10:17:36 -05:00
Adam M Rivera
d29f1ef331
Loiter: Made the "retro loiter" routines configurable. Add RETRO_LOITER_MODE ENABLED to APM_Config.h to enable the older loiter shtuff.
2012-04-19 10:16:29 -05:00
James Goppert
0e7e77760a
Updated ArduPlane/ArduCopter cmake options.
2012-04-18 15:16:02 -04:00
Adam M Rivera
7b277d7044
config.h: Added RTL_APPROACH_DELAY config value.
2012-04-16 14:00:08 -05:00
rmackay9
84b07b5e6a
ArduCopter - LEDS - added new COPTER_LEDS definition
...
Code by Robert Lefebvre
2012-04-12 22:55:32 +09:00
Andrew Tridgell
0bc604f030
ACM: removed FORCE_AUTOMATIC_DECLINATION_UPDATE
...
we now have the EEPROM option COMPASS_AUTODEC instead
2012-03-30 14:25:27 +11:00
Adam M Rivera
51b70e4d36
ArduCopter: Changed implementation of configuration value for automatic declination. There is now a FORCE_AUTOMATIC_DECLINATION_UPDATE that when enabled will update the declination on every GPS 3D fix regardless of whether or not the user saved a value to the EEPROM. By default the declination will only be set by the automatic declination routine if the user has not saved a declination to the EEPROM.
2012-03-30 14:25:06 +11:00
rmackay9
1f4cfb9333
ArduCopter - added PID log type. Implemented for Yaw stabilize and rate controllers.
2012-03-25 16:09:08 +09:00
Jason Short
e2560c5865
Throttle_hold was in APM_Config - which is ignored by the Mission planner Hex generator
2012-03-22 10:01:24 -07:00
rmackay9
0773a25b5d
ArduCopter - increased default THROTTLE_CRUISE to 450
2012-03-20 16:34:07 +09:00
rmackay9
dc92da818c
ArduCopter - remove reference to AUTO_RESET_LOITER that is not used anymore
2012-03-18 14:53:19 +09:00
Jason Short
491af02d8a
ACM: Lowered gains from flight tests today with 3DR Quad
2012-03-17 11:04:01 -07:00
Jason Short
3038da1dc3
ACM: Softer Loiter Gains
2012-03-16 14:10:19 -07:00
Jason Short
a52a14bf12
Tune down Loiter_P a hair
2012-03-15 19:17:27 -07:00
Jason Short
48ba24a810
ACM: Loiter tuning updates, turned up I a bit, a higher I will work better if the system is well tuned.
2012-03-13 10:23:31 -07:00
Jason Short
7034b709d1
ACM: removing old define
2012-03-12 13:11:30 -07:00
Jason Short
0b51d9b8b0
ACM: Made Loiter_D 0 by default. Accidentally left it on by default.
2012-03-12 10:37:15 -07:00
Jason Short
a989b88680
ACM: made same as Loiter I
2012-03-11 23:21:49 -07:00
Jason Short
0d434ca92c
ACM: Tuning based on flights today
2012-03-11 23:21:49 -07:00
Adam M Rivera
2524f9c8df
AP_Declination: Added new config value to allow the user to have the declination overwritten on every 3D fix.
...
Signed-off-by: Andrew Tridgell <tridge@samba.org>
2012-03-11 20:59:47 +11:00
Jason Short
83729d0f75
ACM: decreased rate P for alt hold to remove bumpy repsonse
2012-03-10 12:41:06 -08:00
Jason Short
220d5a1c6e
ACM: Increased the altitude error P for smoother alt hold response
2012-03-10 12:40:44 -08:00
Jason Short
4b703e8842
decreased the loiter rate P for overshoot
2012-03-10 12:40:07 -08:00
Andrew Tridgell
7e4c8592ff
ACM: make it possible to build ArduCopter with quaternions
2012-03-10 10:34:29 +11:00
Jason Short
730476fdfd
ACM -
...
Implemented automatic ranging of Alt Hold gains. Works well in simulator and testing.
- alt hold estimation moved to 50 hz
- simple fixed observer calc for smooth and accurate climb rates useful for derivative calcs
- auto-reset of the I term by moving I value into throttle value. This recalcs the gain every 20seconds for battery drainage compensation in long flights.
- remove filtering for Nav_throttle
- added a way to lower the gain on nav_throttle for descents by / climb_rate error by 2 - seems to work OK and keeps copter from dropping like a rock when the Baro drifts quickly lower.
- removed old throttle hold set point code
- made throttle override for alt hold +- 200 vs 250
2012-03-06 22:22:14 -08:00
Jason Short
c26eb6afcc
ACM: Updated config values
2012-03-06 22:12:24 -08:00
Andrew Tridgell
0fc646d666
ACM: set default RC fast speed to 400Hz
2012-03-02 17:57:08 +11:00
Jason Short
7c09e4a5e6
added stab_d gain scheduling - off by default
2012-02-28 20:16:40 -08:00
Jason Short
ba68d6d8a1
Set loiter rate enabled by default
2012-02-26 12:29:28 -08:00
Jason Short
e06d8142c1
Added OPtion for non-rate based loiter
2012-02-26 11:33:37 -08:00
Jason Short
cc5ab4aebf
increased speed of alt hold I term based on Jani's Logs
2012-02-25 13:31:21 -08:00
Jason Short
385828824d
updated Gains for Marco's loiter test
2012-02-23 22:03:26 -08:00
Jason Short
885710fce6
updated max throttle define
2012-02-18 21:14:13 -08:00
Jason Short
1b46daa12e
some better defaults for JDrones
2012-02-18 14:23:21 -08:00
Jason Short
b052dab80d
Adjusted gains to move closer to Marco's tests
2012-02-16 22:19:39 -08:00
Jason Short
3d63bb6cd4
Added acro_p to the params
2012-02-15 11:29:25 -08:00
Jason Short
21856e7696
new defaults for params
2012-02-15 09:10:15 -08:00
Jason Short
4faba2048c
Lowered for Jani
2012-02-13 15:25:23 -08:00
Pat Hickey
470fd8788e
ArduCopter Channel Config: config vars for user override of MOT_n mapping
...
* config variable CONFIG_CHANNELS has possible values
CHANNEL_CONFIG_DEFAULT or CHANNEL_CONFIG_CUSTOM
* config_channels.h only provides APM1/APM2 mapping when
CONFIG_CHANNELS == CHANNEL_CONFIG_DEFAULT
2012-02-11 16:05:51 -08:00
Jason Short
0a63f104ab
Gain adjustments for 3d frame.
2012-02-11 15:29:11 -08:00
Jason Short
dc15fe4c5d
Moved to Rate_I by default for Jani to test
2012-02-10 22:32:55 -08:00
Jason Short
50aaa09348
Up Nav_Rate_P
2012-02-09 22:38:36 -08:00
Jason Short
62627e9b57
reverted to Save_WP now that CH7 triggering is fixed
2012-02-09 22:33:01 -08:00
Jason Short
c35ad2d493
Loiter update - removed compensation curve. Did some more math and its's not worth the effort, harder to tune.
2012-02-09 22:22:00 -08:00
Randy Mackay
fe7a0a97ab
ArduCopter - CH7 - changed default to CH7_DO_NOTHING
2012-02-09 20:26:01 +09:00
Randy Mackay
b851d39eaa
OptFlow - reenable OF_LOITER pid controller and reduce I term
2012-02-01 08:04:18 +09:00
Jason Short
21bd48b6c3
Loiter PIDs
2012-01-30 21:13:03 -08:00
Jani Hirvinen
009e87105f
Minor changes for PID for jDrones motors due latest changes on control laws.
2012-01-31 09:00:31 +07:00
Jason Short
a3862ced62
cosmetic
2012-01-29 21:55:17 -08:00
Jason Short
02aacc454b
Lowering the throttle_P values by default
2012-01-29 16:27:13 -08:00
Jason Short
7833cea9d4
2.2B6 - Please verify Heli still functions properly.
...
Added AC_PID lib
Updated landing code
bug fixes
2012-01-28 22:00:05 -08:00
Randy Mackay
122623f64b
OpticalFlow - added OF_LOITER flightmode
2012-01-28 09:27:16 +09:00
Randy Mackay
8dee001657
Sonar - changed default pin to A0
2012-01-26 22:50:48 +09:00
Randy Mackay
2c906b7b27
OpticalFlow - replaced PI controller with PID controller.
...
Modified optical flow hold to use aggregated position instead of speed.
2012-01-25 21:55:14 +09:00
Jason Short
74daadb252
Revert "test to switch loiter controls"
...
This reverts commit 92270371d038f246d535f0ace9fc19272c44291d.
2012-01-22 14:19:27 -08:00
Jason Short
6476ba22f2
test to switch loiter controls
2012-01-22 12:28:34 -08:00
Jason Short
7edd16e5fe
Added Loiter_D to replace Nav_P for better separation of loiter and navigation tuning.
...
Upped Nav_P defaults to 3 based on windy flight testing
Added minimum WP speed define of 1m/s
Upped loiter_I for better wind performance - was not seeing any overshoot in logs
Made Nav_I default of 0, since we are not using it in the code.
2012-01-21 22:09:13 -08:00
Jason Short
c190f83bb0
AutoLanding timeout for Mission Planner
2012-01-20 22:52:30 -08:00
Jason Short
d2c78d2b75
Stab_D changes units with the new dampening controller updates
...
Stabilize roll is raised to .1 - Flies great, and avoids a slow oscillation that could be affecting loiter.
Loiter P lowered to 1.5 based on feedback
2012-01-20 22:52:30 -08:00
Jason Short
85f10589b2
slowed down slightly
2012-01-20 22:52:29 -08:00
Doug Weibel
ed9f7cb1b6
Update battery monitoring code for ArduCopter
...
Fixes compatibility for APM2. Also a significant update to the battery monitoring code: We previously had monitoring modes for individual cell voltages for 3 and 4 cell lipos. These have been removed as they were never really supported (the cell voltages were computed but were not reported or recorded anywhere). Also, some clean-up/prep work was done for supporting monitoring 2 separate battery packs. The CLI battery and current monitoring tests were consolidated into 1 test.
changed
2012-01-15 17:10:02 -07:00
Jason Short
95ac9d163e
lowered Loiter I, commented out unused var
2012-01-14 11:20:40 -08:00
Jason Short
154411c96c
removed unused defines
...
lowered default Loiter gain
2012-01-12 22:28:58 -08:00
Jason Short
257890d5be
New Loiter Gains for new Loiter methods
2012-01-11 22:41:51 -08:00
Pat Hickey
a30558e9b2
ArduCopter config.h: add standard ifndef/define header macro wrappers
2012-01-09 21:57:01 -08:00
Randy Mackay
f68d23d91e
ArduCopter - added ROLL_PITCH_STABLE_OF (i.e. Stabilised Roll/Pitch + adjustments based on optical flow)
...
Removed optical flow from regular loiter for now until it's tested.
2012-01-09 13:53:54 +09:00
Randy Mackay
3dfa26920f
ArduCopter - changed Sonar to use A1 (was AN4)
2012-01-08 17:48:30 +09:00
Jason Short
06e032db68
Quad frame - X is default
...
added wind comp stability option to config - off by default
2012-01-07 22:27:26 -08:00
Jason Short
67bf991598
removed unused Airspeed config
2012-01-04 09:28:36 -08:00
Jason Short
74b203c7f2
Lowered Yaw to prevent overshoot based on feedback
2011-12-31 10:10:45 -08:00
Jason Short
c7f93f8718
Updated Configs based on field testing.
2011-12-30 23:48:04 -08:00
Jason Short
21460a57ae
Yaw Performance tweaks
2011-12-29 23:02:03 -08:00
Jason Short
95a70cf32e
lowered to nav_lat and nav_lon int16
...
added a version that didn't have I term added to get a better indication of velocity estimation
2011-12-29 23:02:03 -08:00
Jason Short
17acbc4572
updated Loiter gains
2011-12-29 23:02:03 -08:00
Jason Short
bb954bc479
Upped Yaw speed to deal with performance complaints
...
Added new Stabilize D term default of .25
2011-12-29 23:02:02 -08:00
Jason Short
7e1e1f84b3
updated Loiter PIDs
2011-12-29 23:02:02 -08:00
Jason Short
4b5437afe8
Enable Magnetometer by default
2011-12-29 23:02:02 -08:00
Randy Mackay
bbe6dea980
OptFlow - initial support for APM2 (there are still problems) including adding ability to set Chip Select pin.
...
Other unrelated changes are:
a) fixed typo in 'esitmate_velocity' to 'estimate_velocity'.
b) moved init_compass from system.pde to sensors.pde which seemed consistent with other sensors.
2011-12-30 12:06:31 +09:00
Andrew Tridgell
433df08cb3
ACM: enable compass by default on APM2
2011-12-28 20:30:35 +11:00
Jason Short
d7af42c925
Getting rid of Simple Logging
2011-12-23 18:44:30 -08:00
Jason Short
0f91fbcee5
Made WP radius 1 by default
2011-12-23 15:01:53 -08:00
Jason Short
a966a178f8
increased crosstrack thanks to float math fix
...
decreased loiter iterm, decreased throttle iterm based on simulator runs
2011-12-23 14:42:50 -08:00
Pat Hickey
f1624621b3
ArduCopter Logging: DISABLED means DISABLED again; CONFIG_LOGGING added
...
CONFIG_LOGGING selects LOGGING_SIMPLE and LOGGING_VERBOSE. Verbose
logging is the default, implemented in Log.pde. Simple logging is
optional, but the default for the 1280 build, implemented in
Log_simple.pde
2011-12-19 21:04:51 -08:00
Jani Hirvinen
106801a59c
config settings for jD motors
2011-12-19 09:29:05 +07:00
Jason Short
f11f2c6d97
added some more throttle imax range
...
renamed Super Simple
2011-12-15 20:51:41 -08:00
Doug Weibel
5d197ae337
Change logging to default on for 2560
2011-12-13 20:53:44 -07:00
Jason Short
c9b317fc27
Gain updates
2011-12-12 17:47:45 -08:00
Jason Short
e4559bbf5c
Added param option for Simple mode reset
2011-12-12 17:47:45 -08:00
Jason Short
6bc90d6289
Just upped the nav_imax value
2011-12-12 10:10:33 -08:00
Andrew Tridgell
a22893124d
fixed LOGGING_ENABLED default on ArduCopter
2011-12-12 23:40:43 +11:00
Andrew Tridgell
358dc91d41
fixed hil ArduCopter build
2011-12-12 15:14:55 +11:00
Pat Hickey
d7f77aec93
ArduCopter & ArduPlane: Added support for apm2beta build via APM2_BETA_HARDWARE define
...
* This enables the BMA085 driver for compatibility with beta boards.
* The CLI_SLIDER_ENABLED=DISABLED line does not need to be in the makefile.
config.h takes care of this default.
2011-12-11 15:21:09 -08:00
Pat Hickey
62844d8ddc
ArduCopter: added config.h and defines.h to support CONFIG_BARO
2011-12-11 15:21:09 -08:00
Jason Short
e8e126a636
removed CLI switch by default, decreased Nav I
2011-12-11 09:53:44 -08:00
Randy Mackay
67855b207d
Arducopter, RangeFinder - added SONAR_TYPE parameter and properly support the XL (default), LV and long distance XL (aka XLL) sonar types
2011-12-11 16:40:59 +09:00
Randy Mackay
0b24914066
OptFlow - turning on optical by default
2011-12-10 23:22:40 +09:00
Randy Mackay
fa0723f115
ArduCopter - removed limitation on Maxbotix sonar type requiring ADC so it can work with APM2.
...
modified default analog pin in test sketch to be AN4 which is consistent with APM2 default
2011-12-10 18:33:30 +09:00
Pat Hickey
cc38189f71
ArduCopter config: Correct LOGGING_ENABLED defaults to force disable for 1280
...
Per email, this is what Jason meant to do in aeb92870, but previous code
forced logging enable for all non-1280 users.
2011-12-09 15:06:10 -08:00
Jason Short
e8a14c8d93
simple patch to improve alt hold based on stability patch
2011-12-04 21:32:33 -08:00
Jason Short
5ed300db7e
disabled Flash logs in 1280 by default
...
Added stability patch I values and limits
2011-12-03 15:38:46 -08:00
Andrew Tridgell
38c85c44ae
ArduCopter: rename purple to APM2
2011-11-25 20:00:19 -08:00
Andrew Tridgell
3a542b3ef3
USB-MUX: enable USB MUX switching for ArduCopter
2011-11-25 20:00:19 -08:00
Andrew Tridgell
6093db948b
compass: added AP_COMPASS_APM2_SHIELD
...
this makes the orientation clearer
2011-11-25 20:00:18 -08:00
Pat Hickey
3131ab16ef
remove BROKEN_SLIDER code
...
use the new CLI_SLIDER_ENABLED option and the "hit ENTER 3 times"
method
2011-11-25 20:00:17 -08:00
Pat Hickey
3f2692d1da
purple: added configuration logic for APM1 versus purple hardware
...
This abstracts the names for LED on/off (due to the different wiring
of LEDs on APM1 and purple), and adds the needed config defines for
the two hardware types
2011-11-25 20:00:16 -08:00
Jason Short
89e014c06a
Added alternate alt hold,
...
New ESC Calibration Routine
2011-11-21 22:12:19 -08:00
Jason Short
2600f19172
RTL Yaw hold as default
2011-11-20 12:50:13 -08:00
Jason Short
fbf09dbf2d
Made save WP the default
...
Cosmetic updates
2011-11-20 12:50:12 -08:00
Jason Short
9bc4328724
Added crosstrack gain and lowered alt hold rate gain
2011-11-19 13:59:15 -08:00
Jason Short
937a364dce
Made RTL Altitude hold current by default
2011-11-16 00:22:23 -08:00
Jason Short
930ee51bbe
added scale note
2011-11-13 00:25:04 -08:00
Jason Short
fafa6e52e9
back to original config for testing
2011-11-09 13:53:26 -08:00
Jason Short
f994d16a48
Lowered Nav_P based on SIM data
2011-11-09 12:46:34 -08:00
Jason Short
a8d622d8e6
Lowered Nav_P I term to ramp slower base on SIM
2011-11-09 11:30:50 -08:00
Jason Short
2dc2a2114a
restoring throttle i term for SIM
2011-11-08 11:51:49 -08:00
Jason Short
10bbfdbe11
PID test for alt hold to narrow down on a bug
2011-11-08 10:13:16 -08:00
Jason Short
3153257d37
default top_bottom ratio 1.0
2011-11-06 22:43:49 -08:00
Jason Short
1df9f8488d
updated Alt hold PIDs
2011-11-01 09:30:34 -07:00
Jason Short
07daf34ccc
Added a slew rate to the alt change rate.
...
Added better reporting of throttle control
upped constraints for alt hold
Additional logging for CTUN lay hold
2011-10-28 21:29:10 -07:00
Jason Short
27d9712e80
Merge branch 'master' of https://code.google.com/p/ardupilot-mega
...
Conflicts:
libraries/APM_PI/APM_PI.cpp
2011-10-27 12:41:00 -07:00
Jason Short
0b4a3ccadb
Acro PI defaults
2011-10-27 11:55:13 -07:00
Andrew Tridgell
5a44298d57
CLI: enable "hit enter 3 times" support for CLI
...
if you hit enter 3 times before you send any mavlink packets, we will
enter CLI mode
2011-10-27 21:54:07 +11:00
Jani Hirvinen
a503d9a7a7
adding missing config parameters
2011-10-21 10:41:52 +07:00
Jason Short
42d0b5cdb3
tweaked Alt hold PIDs, loiter PIDs based on SIM testing and feedback.
...
Increased distance error for loiter for faster return to center.
2011-10-16 15:41:54 -07:00
Jason Short
6a5aefd0ec
Added gains to adjust travel of camera.
2011-10-15 16:34:57 -07:00
Jason Short
4052fd4f73
Made wpspeed governor run per second so 1hz gps doesn't fail. Gave a 1m/s minimum. Increased WPspeed max to 4.0m/s
2011-10-15 15:35:18 -07:00
Jason Short
43b3015963
lowered DCM RP gains
...
made Instant_PWM optional
upped PWM output to 400hz
2011-10-11 22:20:23 -07:00
Andrew Tridgell
d89ae696ef
merged the GCS updates from ArduPlane to ArduCopter
...
this removes all the non-MAVLink GCS options, and simplifies the HIL
and GCS code a lot. It also adds async sending of low priority GCS
text messages.
2011-10-11 20:53:43 +11:00
Jason Short
167df79b49
Better Loiter PIDs
...
Fixed RTL overshoot bug
2011-10-06 17:42:09 -07:00
Jason Short
b0bd9d1c44
Added second PI loop for alt hold.
...
Upped gains for default JDrones Frame
added gains for second PI loop for alt
removed some tests for 1280 space constraints
2011-10-02 11:36:23 -07:00
Jason Short
de61e87128
Added ADC gyro Filtering for quads - this fixes a noise issue introduced into the controller
...
added Position mode
removed
Added back in the accelerometer experiment
Added filter_result boolean to enable filter on the fly
2011-09-29 23:27:23 -07:00
Jason Short
758d0e1aec
Attempting to mimic loiter values for 4.0.42
...
lowered Rate Error max in loiter
2011-09-28 23:11:19 -07:00
Jason Short
c209d6e6dd
2.0.46 -Not flight tested!
...
restored 42 alt hold code
removed throttle timer, replaced with safer constant
increased alt control range
reformatted nav_rate calls
removed unused simple mode defines
set alt hold home to 10m
tuned down rateP to .13 from .14 for broader application.
2011-09-27 09:35:05 -07:00
Jason Short
b2a2221474
Fixed issue with Simple mode changes.
...
Reverted to simpler, safer timer code for throttle hold
2011-09-25 14:16:35 -07:00
Jason Short
d495e6a9c4
turned off Stabilize_I by default because it was hurting loiter
...
tweaked speed control of rate_nav
2011-09-24 21:49:45 -07:00
Jason Short
e961d3f3d4
Removed default Rate_I for pitch and roll
...
added change speed control for missions
2011-09-24 09:49:11 -07:00
Jason Short
25b0a3c43b
Added a default, but low throttle cruise value
...
Added a clear integrator for Rate I to prevent tip ups at launch.
2011-09-22 23:10:55 -07:00
Jason Short
7177bcec77
removed old CH6 tuning defines
2011-09-22 18:51:41 -07:00
Jason Short
cfd2c31fb2
Better Tuning for default Quad
2011-09-22 18:30:29 -07:00
Jason Short
991279851a
Refined Throttle Timer reset
...
Reduced Loiter I gain to decrease overshoot.
2011-09-22 17:38:39 -07:00
Jason Short
078f64e276
Fixed Throttle integrator bug. Time was not being reset causing a big drop in throttle control.
2011-09-22 12:28:46 -07:00
Jason Short
73fd0084be
Added Piezo Support, code from Oliver.
2011-09-18 17:12:28 -07:00
Jason Short
f79b8de5e8
removed DCM reference from OPT FLOW
2011-09-16 19:17:50 -07:00
Jason Short
b948e0f02b
Lowered Loiter_I - higher value didn't test well.
2011-09-16 18:24:42 -07:00
Jason Short
129c13e065
Fixed CIRCLE mode trig error
...
made loiter_radius * 100 in Params
updated gains
2011-09-16 16:54:45 -07:00
Jason Short
8d0a2fae9b
cleanup
...
added more ifdef for optflow
2011-09-15 23:41:15 -07:00
Jason Short
d29cfbcee3
Integration of optical flow
...
bug fixes for new Simple mode
increased Baro filter by 2 fields
2011-09-15 23:33:00 -07:00
Jason Short
1ce2308d11
Removed Simple Mode
...
Added Simple option to mode switch positions
removed unused OptFlow code
added reset lat and lon error
removed unused init_auto
Fixed log formatting
Added simple mode bitmask
removed pitchmax
added CLI setup for enabling Simple mode to any switch position
2011-09-14 13:58:18 -07:00
Jason Short
c15b6be83f
increased imax
2011-09-11 20:28:43 -07:00
Jason Short
d733868fea
Fixed Yaw mode for CIRCLE
2011-09-11 11:48:11 -07:00
Jason Short
02bfd43390
Fixes Alt hold mistake
...
Moves tuning into runtime definable param
Added more IMax to throttle
Signed-off-by: Jason Short <jasonshort@gmail.com>
2011-09-10 15:16:51 -07:00
Andrew Tridgell
1456a2a912
renamed top level directories
...
ArduCopterMega -> ArduCopter
added archives directory for old code
2011-09-09 11:27:41 +10:00