Commit Graph

1170 Commits

Author SHA1 Message Date
rmackay9 a869a01294 ArduCopter - Log.pde - added wrap_360 to compass heading field of ATT message to resolve overflow problem that caused heading to appear as being off by 70 degrees 2012-03-12 12:09:04 +09:00
Andrew Tridgell 2a03a0584f AP_Declination: disable library when AUTOMATIC_DECLINATION is not ENABLED
unfortunately this library was causing avrdude to fail to load the hex
to my APM2. Until we work out why, it's disabled.
2012-03-11 21:46:41 +11:00
Adam M Rivera d3667faef4 AP_Declination: Added call to compass.set_initial_location if the compass is enabled when the 3D fix is obtained.
Signed-off-by: Andrew Tridgell <tridge@samba.org>
2012-03-11 20:59:47 +11:00
Adam M Rivera 2524f9c8df AP_Declination: Added new config value to allow the user to have the declination overwritten on every 3D fix.
Signed-off-by: Andrew Tridgell <tridge@samba.org>
2012-03-11 20:59:47 +11:00
Jason Short 62c2aa4924 ACM: Added Loiter D tuning 2012-03-10 14:17:57 -08:00
Jason Short cb8729109c ACM: Added Loiter_D for tuning as #23 2012-03-10 14:17:16 -08:00
Jason Short 0671bb9168 ACM: Firmware rev 2012-03-10 12:45:03 -08:00
Jason Short f9d0dc9daa ACM: disabled auto_calibration until more testing can be done 2012-03-10 12:44:49 -08:00
Jason Short 5ad7320505 ACM: changed alt hold initialization of altitude to be immediate 2012-03-10 12:44:18 -08:00
Jason Short 450f89ec5d ACM: Added note about scaling rates 2012-03-10 12:43:28 -08:00
Jason Short eb53200179 ACM: Altered the scaling speed for altitude changes for faster rises. 2012-03-10 12:43:01 -08:00
Jason Short 204f9957b0 ACM: Added force_new_altitude call to do immediate changes in altitude and no gradual changes. 2012-03-10 12:42:22 -08:00
Jason Short 83729d0f75 ACM: decreased rate P for alt hold to remove bumpy repsonse 2012-03-10 12:41:06 -08:00
Jason Short 220d5a1c6e ACM: Increased the altitude error P for smoother alt hold response 2012-03-10 12:40:44 -08:00
Jason Short 4b703e8842 decreased the loiter rate P for overshoot 2012-03-10 12:40:07 -08:00
Jason Short fc32da0d2e ACM: increased the available rate error constrain, it was too low 2012-03-10 12:39:16 -08:00
Jason Short bd4835a1b2 ACM: removed the experiment for rate error. 2012-03-10 12:38:29 -08:00
Jason Short 29d6085bab added Force_new_altitude call for alt hold 2012-03-10 12:37:54 -08:00
Jason Short 4ba600c0c5 upped throttle manual boost to 225 2012-03-10 12:37:28 -08:00
rmackay9 afc4aceb32 ArduCopter - fixed small compile warning about unused x_iterm and y_iterm in navigation.pde 2012-03-11 01:27:58 +09:00
rmackay9 c7480f2281 ArduCopter - fix to dataflash logging of Mag heading 2012-03-11 01:27:29 +09:00
Andrew Tridgell d75e883fe8 GCS: get_integrator() is now get_gyro_drift() in DCM 2012-03-10 10:34:33 +11:00
Andrew Tridgell 9a06d35772 make 'ENABLE' and 'ENABLED' mean the same things
users get this wrong far too often!
2012-03-10 10:34:33 +11:00
Andrew Tridgell 828ad7625b ACM: removed the ADC filtering code 2012-03-10 10:34:32 +11:00
Andrew Tridgell 1016d3c95d ACM: removed quaternion special cases in CLI code 2012-03-10 10:34:31 +11:00
Andrew Tridgell 8393c0299b ACM: removed the DCM tuning overrides
not needed now that DCM scales with deltat
2012-03-10 10:34:31 +11:00
Andrew Tridgell 7291dfc25a ACM: removed the special case for quaternions in GCS code 2012-03-10 10:34:31 +11:00
Andrew Tridgell d6cfc51ae4 ACM: no need to fetch offsets at startup
AP_Param handles this
2012-03-10 10:34:31 +11:00
Andrew Tridgell ef771fecdc ACM: removed a lot of the special case code for quaternions 2012-03-10 10:34:31 +11:00
Andrew Tridgell 69c29d35ce ACM: change DCM loop to 100Hz
On my APM2 quad this seems to give better results
2012-03-10 10:34:31 +11:00
Andrew Tridgell 2596acc8eb ACM: removed incorrect mode definition 2012-03-10 10:34:30 +11:00
Andrew Tridgell 7a9b3d3388 Quaternion: show "Quaternion test" on startup if enabled 2012-03-10 10:34:29 +11:00
Andrew Tridgell 7e4c8592ff ACM: make it possible to build ArduCopter with quaternions 2012-03-10 10:34:29 +11:00
Andrew Tridgell 9bff4e2c4c ACM: only call the fast loop if the imu has new data
this prevents us spinning waiting for the sensors to gather some data
2012-03-10 10:34:29 +11:00
Andrew Tridgell 367947fd33 HWSTATUS: if we don't know the voltage, report it as zero
this will tell us if board_voltage() is really working
2012-03-10 10:34:28 +11:00
Andrew Tridgell 64cc04ae09 ACM: adjust yaw drift correction constants
this should give the compass a bit more authority
2012-03-10 10:34:28 +11:00
Andrew Tridgell a0ce202d87 ACM: added SIMSTATE, DCM and HWSTATUS messages to ACM 2012-03-10 10:34:27 +11:00
Jason Short 486c56ce41 Consolidated Barometer pressure sensing to a single filter based on Randy's new filter class. 2012-03-08 23:13:04 -08:00
Jason Short c8e9d57567 temp remove filter for quad motors during testing. It's unlikely this filter did anything at all to be honest. 2012-03-06 22:23:06 -08:00
Jason Short 730476fdfd ACM -
Implemented automatic ranging of Alt Hold gains. Works well in simulator and testing.
- alt hold estimation moved to 50 hz
- simple fixed observer calc for smooth and accurate climb rates useful for derivative calcs
- auto-reset of the I term by moving I value into throttle value. This recalcs the gain every 20seconds for battery drainage compensation in long flights.
- remove filtering for Nav_throttle
- added a way to lower the gain on nav_throttle for descents by / climb_rate error by 2 - seems to work OK and keeps copter from dropping like a rock when the Baro drifts quickly lower.
- removed old throttle hold set point code
- made throttle override for alt hold +- 200 vs 250
2012-03-06 22:22:14 -08:00
Jason Short c26eb6afcc ACM: Updated config values 2012-03-06 22:12:24 -08:00
rmackay9 8b256cf924 ArduCopter - fix for stability patch and motor filter meant to deal with engines tendency to speed up faster than they slow down 2012-03-06 23:20:30 +09:00
rmackay9 72a775cc2a ArduCopter - fixed typo in motor filtering for octa, octa_quad and y6 that is suppose to correct for props speeding up faster than they slow down. 2012-03-06 22:19:19 +09:00
rmackay9 706bea5992 ArduCopter - added OCTA_QUAD_FRAME to comments in APM_Configh.h to help user select frame when compiling with arduino 2012-03-06 22:15:02 +09:00
Jason Short 46d7da4d14 Added define for throttle range for altitude changes, updated it to 250 2012-03-05 22:12:53 -08:00
Robert Lefebvre a480b32400 Added support for TradHeli H1 swashplate type. Added new param heli_h1_swash_enabled.
Signed-off-by: Robert Lefebvre <robert.lefebvre@gmail.com>
2012-03-03 08:14:14 -05:00
Andrew Tridgell 0ff44563ec ACM: use g.rc_speed for all APM_RC.SetFastOutputChannels calls 2012-03-02 17:57:08 +11:00
Andrew Tridgell 0fc646d666 ACM: set default RC fast speed to 400Hz 2012-03-02 17:57:08 +11:00
Andrew Tridgell e213f6780e ACM: added RC_SPEED MAVLink parameter
this will set the speed for APM_RC.SetFastOutputChannels()
2012-03-02 17:57:08 +11:00
Andrew Tridgell f781bd735b ACM: fixed Parameters.h to avoid duplicate keys
unfortunately everyone needs to reload
2012-03-02 15:48:28 +11:00
Andrew Tridgell cb874d6097 ACM: added board_voltage() 2012-03-02 15:48:28 +11:00
Robert Lefebvre e49c2d2871 Rescale TradHeli roll_out and pitch_out into the min and max ranges to provide linear motion across the input range instead of stopping when the input hits the constrain value. These calculations are based on an assumption of the user specified roll_max and pitch_max coming into this equation at 4500 or less, and based on the original assumption of the total g.heli_servo_x.servo_out range being -4500 to 4500.
Signed-off-by: Robert Lefebvre <robert.lefebvre@gmail.com>
2012-03-01 22:04:50 -05:00
Jason Short 7c09e4a5e6 added stab_d gain scheduling - off by default 2012-02-28 20:16:40 -08:00
Jason Short a387956814 added stab_d gain scheduling 2012-02-28 20:16:40 -08:00
Jason Short ceef8070ac added stab_d gain scheduling 2012-02-28 20:16:40 -08:00
Jason Short b76c4ecb22 added stab_d gain scheduling 2012-02-28 20:16:40 -08:00
Jason Short efdf6ee79f added option for stab_d gain scheduling 2012-02-28 20:16:40 -08:00
Jason Short ca34d7b7c2 Added test for stab_d gain scheduling. 2012-02-28 20:16:40 -08:00
Pat Hickey 16ed16f403 Cleanup: rm ArduCopter/GCS_Mavlink\ copy.txt
* Not needed, but we can always checkout an old version if it is.

Hi Pat,
This may have been my WIP for the Mavlink 1.0 conversion. I tried to
give Tridge a head start on it. I've made small updates to it in
parallel to the current Mavlink. You can delete it as he would have used
it by now if he felt it was helpful.

Jason

On Feb 28, 2012, at 4:08 PM, Pat Hickey wrote:

It looks like this file was checked in by accident, possibly, but you've
made a few small changes to it since creating it.

Is it important? Should we get rid of it?

Git log of file below.

Thanks
Pat
...
2012-02-28 16:28:27 -08:00
Pat Hickey ff0fc26484 Cleanup: rename files with spaces in their names, replace with underscores
* Skipped /Tools/ArdupilotMegaPlanner/Resources/new...
  and /archive/Configurator/Source/Utilities/TDMS/G...
  because I don't want to mess with that.
2012-02-28 16:14:31 -08:00
Robert Lefebvre 76c3cd88f0 Added heli_collectiveFactor array
Signed-off-by: Robert Lefebvre <robert.lefebvre@gmail.com>
2012-02-28 10:49:28 -05:00
rmackay9 744e5b8c60 ArduCopter - made rate controller filters globals to fix compiler error on Arduino 022 (Arduino 1.0 was fine) 2012-02-28 22:56:26 +09:00
rmackay9 4a0989f95d ArduCopter - Attitude.pde - updated get_rate_roll and get_rate_pitch to use new average filter.
modified all int to int16_t in Attitude.pde
2012-02-28 21:26:37 +09:00
rmackay9 17d94b61ed ArduCopter - modified to work with new Filter library 2012-02-28 21:02:44 +09:00
Jason Short ba68d6d8a1 Set loiter rate enabled by default 2012-02-26 12:29:28 -08:00
Jason Short e06d8142c1 Added OPtion for non-rate based loiter 2012-02-26 11:33:37 -08:00
Jason Short 6e53949c2a removed Constraint that caused JLN's horizontal drift. 2012-02-26 11:33:37 -08:00
Jason Short 517172ba20 Added Loiter Rate Tuning 2012-02-26 11:33:37 -08:00
Jason Short 0ce0c7c262 Added Loiter_rate_tuning 2012-02-26 11:33:36 -08:00
Jason Short eac77504a3 Added more Logging for PIDs. 2012-02-26 11:33:36 -08:00
rmackay9 8193c786ef ArduCopter - added #include <Filter.h> to unbreak the build! 2012-02-26 17:05:41 +09:00
rmackay9 69132e0fe7 ArduCopter - change sonar to use new mode filter from Filter library 2012-02-26 15:35:14 +09:00
Jason Short f27e9f9ca1 added a simple rest of nav_throttle just in case 2012-02-25 13:31:21 -08:00
Jason Short cc5ab4aebf increased speed of alt hold I term based on Jani's Logs 2012-02-25 13:31:21 -08:00
Jason Short 1ce267f904 increased the rate error for more responsive alt hold 2012-02-25 13:31:21 -08:00
Jason Short a924c3685e Based on Jani's latest logs I've made two tweaks to alt hold.
The first is to remove the filter on the throttle output for alt_hold.

The second was to open up the constraint on climb rate. This is to deal with larger than expected disturbances causing altitude changes.
2012-02-25 13:31:21 -08:00
Andrew Tridgell e2bbc795ad ACM: use a NULL gps pointer in DCM init
current DCM API does need a GPS reference passed in, but it can be
NULL
2012-02-25 15:08:49 +11:00
Andrew Tridgell 0248b48d30 allow MAG_ENABLE to be changed in flight
this disables the compass in DCM if MAG_ENABLE is changed in
flight. Without this we would use a fixed yaw once the compass is
disabled

This also makes sure we don't pass the compass to DCM till we have
done a read. This ensures we have a good compass fix for the initial
DCM heading
2012-02-25 14:51:09 +11:00
Andrew Tridgell 864ed1a87f ACM: check the return of compass.init()
if the compass fails to initialise then don't pass it to DCM, or we
will get no yaw control. Report the init failure to the user.
2012-02-25 14:51:08 +11:00
Andrew Tridgell 698749dd92 ACM: don't pass a gps pointer to DCM
after discussion with Randy, we don't want ArduCopter to fall back to
GPS for yaw when the compass becomes unhealthy. So we shouldn't pass
the gps object to the DCM code at all.
2012-02-25 14:51:08 +11:00
Andrew Tridgell 690dc9052a GCS: force scalar type in copy_name()
this enables access to compass offsets over MAVLink
2012-02-25 11:37:20 +11:00
Andrew Tridgell 2e9105c68a AP_Param: added special handling for Vector3f
We would like to be able to use Vector3f as a parameter while exposing
the individual elements of the vector as MAVLink parameters. This
change to AP_Param makes that possible, by giving AP_Vector3f a dual
personality
2012-02-25 11:37:20 +11:00
Jason Short 1e254cbca0 Compass heading added to ATT log 2012-02-24 12:11:15 -08:00
rmackay9 57e5eee8c8 TradHeli - increase max yaw input to 45 degrees 2012-02-24 20:18:40 +09:00
Jason Short 385828824d updated Gains for Marco's loiter test 2012-02-23 22:03:26 -08:00
Jason Short 24345d4f43 Loiter updates 2012-02-23 22:03:26 -08:00
Andrew Tridgell 1cd3172954 ACM: ensure update_trig() doesn't cause NAN values for cos_roll/cos_pitch
the DCM matrix could have a value over 1.0 for c.x due to rounding
errors
2012-02-24 11:52:55 +11:00
Jason Short 364afe8da0 added a constraint to D term 2012-02-23 09:14:44 -08:00
Andrew Tridgell 95ef9206dc DCM: renorm_sqrt_count is now called renorm_range_count 2012-02-23 08:16:08 +11:00
Jason Short c7c16a5b0f Emile's Fixes 2012-02-22 10:27:34 -08:00
Jason Short 4483f19f85 Marco's Hexa Motors 2012-02-22 09:55:44 -08:00
Jason Short 242f54793c revved a version 2012-02-22 09:00:42 -08:00
Jason Short 729c824809 made timer unsigned 2012-02-21 21:49:03 -08:00
Jason Short 42b5d47f7b commented out control mode debug print 2012-02-21 21:48:07 -08:00
Jason Short 30efbae0e9 removed old comments 2012-02-19 14:21:27 -08:00
Jason Short 265c5255a3 Added slow_wp default in AP mode 2012-02-19 13:15:40 -08:00
Jason Short 336441b109 reset slow_WP option at mode switch 2012-02-19 13:13:42 -08:00
Jason Short 81a861c8ac Added slow wp option in calc_desired_speed 2012-02-19 13:13:21 -08:00
Jason Short 33d4d52a6b set Slow WP option for RTL in Auto mode 2012-02-19 13:12:23 -08:00
Jason Short cae49b3543 Added "slow WP" option for RTL. 2012-02-19 13:11:59 -08:00
Jason Short b54d08f410 Updated manual throttle control during throttle hold 2012-02-19 12:40:51 -08:00
Jason Short bcd5129f9b added workaround for resetting alt. 2012-02-19 12:40:08 -08:00
Jason Short fa32b084bd Added SW test for Manual Boost 2012-02-19 12:39:40 -08:00
Randy Mackay 9fabdb5797 TradHeli - change throttle range back to 0~1000 (was temporarily changed to be 1250~850 which limited the range of the swash plate's vertical movements) 2012-02-20 00:27:12 +09:00
Randy Mackay e146f225b1 ArduCopter - remove unnecessary block for next GPS value before saving home location 2012-02-19 15:38:40 +09:00
Andrew Tridgell df8a557630 AP_Param: update users of AP_Param for ParamToken 2012-02-19 17:05:28 +11:00
Andrew Tridgell 12327eb2a9 Heli: fixed some 'used before initialised' warnings 2012-02-19 16:34:43 +11:00
Jason Short 028de5d2c5 Axis lock beta (off by default) 2012-02-18 21:16:19 -08:00
Jason Short 885710fce6 updated max throttle define 2012-02-18 21:14:13 -08:00
Jason Short 05024cc06c Change 800 to a define 2012-02-18 21:13:28 -08:00
Jason Short 04b70ffdc2 added Axis_Lock params 2012-02-18 21:13:06 -08:00
Jason Short ff2b4ecb7a updated throttle range 2012-02-18 21:11:06 -08:00
Jason Short 1e37a0ec17 added a limit to range output 2012-02-18 21:08:17 -08:00
Jason Short 1b46daa12e some better defaults for JDrones 2012-02-18 14:23:21 -08:00
Randy Mackay b92d7aaad5 ArduCopter - fix for yaw control on Octa Quad Plus frame. 2012-02-18 22:04:09 +09:00
Randy Mackay 232359186e TradHeli - fixed small parameter bug affecting helis. The servo parameters were declared as GSCALAR instead of GGROUP in Parameters.pde.
also renamed heli parameters from _coll_ to the more descriptive _collective_
2012-02-18 20:57:51 +09:00
Randy Mackay b64c0da003 ArduCopter - updated version to 2.4 2012-02-18 18:44:29 +09:00
Andrew Tridgell 6929226b96 ACM: expanded EEPROM parameter area by 256 bytes 2012-02-18 10:51:57 +11:00
Andrew Tridgell 718a5b70e3 AP_Param: fixed saving of sensor calibration
this fixes the saving of the accel and gyro calibration to EEPROM,
which was initially broken by the AP_Param conversion
2012-02-18 10:51:57 +11:00
Jason Short b532cb91b1 added Rate_D tuning value 2012-02-17 15:23:59 -08:00
Jason Short 0075901f77 upped rate loop to 250hz 2012-02-17 15:23:59 -08:00
Jason Short 5218220f0f re-implemented WII Dampening filter for Marco. 2012-02-16 22:38:23 -08:00
Jason Short b052dab80d Adjusted gains to move closer to Marco's tests 2012-02-16 22:19:39 -08:00
Jason Short 17c6c7b294 added extra gain logging 2012-02-16 22:09:22 -08:00
Jason Short 908ca4e915 scaled X velocity 2012-02-16 22:09:22 -08:00
Jason Short bc1593e89c cast to float 2012-02-16 22:09:21 -08:00
Jason Short 632cc783a1 cast D term to float just in case 2012-02-16 22:09:21 -08:00
Jason Short 36a120d8df removed some unused vars,
formatting, made loop speed same as PIDT1 to eliminate variable.
2012-02-16 22:09:21 -08:00
Jason Short a43ee36bee CH 6 Range setup 2012-02-15 11:47:54 -08:00
Jason Short 3d63bb6cd4 Added acro_p to the params 2012-02-15 11:29:25 -08:00
Jason Short e8b6f5ecee allow auto-land if failsafe is triggered 2012-02-15 10:53:54 -08:00
Jason Short fabeccad4a Marco's updated Motor testing code 2012-02-15 10:49:35 -08:00
Jason Short 73591a0ca5 Added lengthy note about motor testing 2012-02-15 10:49:11 -08:00
Jason Short 9a3e862b55 added option in code for Loiter specific gains 2012-02-15 09:10:15 -08:00
Jason Short e249c8466d AP slew rate 2012-02-15 09:10:15 -08:00
Jason Short 21856e7696 new defaults for params 2012-02-15 09:10:15 -08:00
Jason Short fcb24ee17d Added Acro_P 2012-02-15 09:10:14 -08:00
Jason Short 574b86b02e synced params 2012-02-15 09:10:14 -08:00
Jason Short 91edeeeef2 added RTL_land_enabled
added auto_pilot slew rate
2012-02-15 09:10:14 -08:00
Jason Short aa0662008b Added new params for CH6 Tuning
moved enums to give more room for additional PIDs for Loiter
added new Acro_P gain
added auto_land_enabled option
added pi_loiter_lon and pi_loiter_lat for separate tuning of loiter
2012-02-15 09:10:14 -08:00
Jason Short 05abe44f32 Added range setting via a parameter for CH6 tuning 2012-02-15 09:10:14 -08:00
Jason Short c9b432955d removed unused Vars 2012-02-13 15:25:23 -08:00
Jason Short 4faba2048c Lowered for Jani 2012-02-13 15:25:23 -08:00
Andrew Tridgell ecdbfd257a token is 16 bits now 2012-02-13 16:22:53 +11:00
Andrew Tridgell d55a0c3a71 added AP_Param::show_all()
this moves the logic into common code
2012-02-13 16:22:52 +11:00
Andrew Tridgell 0f9adbdae0 token size for first()/next() is now 16 bits 2012-02-13 16:22:52 +11:00
Andrew Tridgell 617082769a go back to 1024 bytes for variables in EEPROM 2012-02-13 16:22:52 +11:00
Andrew Tridgell 0b3e3ec5c8 added group indexes to GCS_MAVLINK class 2012-02-13 16:22:52 +11:00
Andrew Tridgell d4305e0ae2 fixed apm2beta build with AP_Param 2012-02-13 16:22:52 +11:00
Andrew Tridgell 16417b651e the ACM parameters have a max size of 1114 bytes
to ensure that all parameters can be saved, expand parameter area by
256 bytes
2012-02-13 16:22:52 +11:00
Andrew Tridgell 3b4cae3cc3 adapted main ACM code for AP_Param 2012-02-13 16:22:52 +11:00
Andrew Tridgell c9c422539e update ACM MAVLink code for AP_Param 2012-02-13 16:22:52 +11:00
Andrew Tridgell a2d0900460 fixed warning in Log build 2012-02-13 16:22:52 +11:00
Andrew Tridgell bf1eb670e3 update main parameter code for AP_Param in ACM 2012-02-13 16:22:52 +11:00
Andrew Tridgell f1a41b041f log: fixed some integer size errors
need to be careful with the types passed to printf()
2012-02-12 20:38:37 +11:00
Pat Hickey 306a3bb4f9 Makefile: extra convenience target for apm2hexa 2012-02-11 16:05:51 -08:00
Pat Hickey 84dd0d2fda ArduCopter Hexa output_motor_test: individually select all 6 motors
* each of the 6 hexacopter motors can be selected individually
  by moving the joystick to extremes.

* previously, this was built from the quadcopter output_motor_test
  and some motors (left/right motors on +, front/back motors on X)
  were only selectable as pairs.
2012-02-11 16:05:51 -08:00
Pat Hickey 739317276d ArduCopter setup motors: print basic instructions. 2012-02-11 16:05:51 -08:00
Pat Hickey 6573cec611 ArduCopter APM_Config.h: add sample custom channel config
* uses new config variables introduced in 8a19543fd1e09621ba
2012-02-11 16:05:51 -08:00
Pat Hickey 470fd8788e ArduCopter Channel Config: config vars for user override of MOT_n mapping
* config variable CONFIG_CHANNELS has possible values
  CHANNEL_CONFIG_DEFAULT or CHANNEL_CONFIG_CUSTOM
* config_channels.h only provides APM1/APM2 mapping when
  CONFIG_CHANNELS == CHANNEL_CONFIG_DEFAULT
2012-02-11 16:05:51 -08:00
Jason Short 2c65fc9ddf Cosmetic tweaks for tuning 2012-02-11 15:29:11 -08:00
Jason Short 0a63f104ab Gain adjustments for 3d frame. 2012-02-11 15:29:11 -08:00
Jason Short 969ac70000 reset All for Auto takeoff 2012-02-10 22:54:29 -08:00
Jason Short b1d52da431 reset Rate_I for takeoff 2012-02-10 22:50:56 -08:00
Jason Short efce991bfb upped max target speed to center of loiter 2012-02-10 22:46:27 -08:00
Jason Short 8ae53bffd2 Made Yaw Hold universal for Acro 2012-02-10 22:32:55 -08:00
Jason Short dc15fe4c5d Moved to Rate_I by default for Jani to test 2012-02-10 22:32:55 -08:00
Jason Short c64d781dce get_acro_yaw added 2012-02-10 22:32:55 -08:00
Jason Short 19ab0f481e made Yaw work like Roll and Pitch 2012-02-10 22:32:55 -08:00
Jason Short 9f8d7d5076 Minimize the Yaw Deadzone 2012-02-10 22:32:55 -08:00
Jason Short 50aaa09348 Up Nav_Rate_P 2012-02-09 22:38:36 -08:00
Jason Short 62627e9b57 reverted to Save_WP now that CH7 triggering is fixed 2012-02-09 22:33:01 -08:00
Jason Short 3afaf2689c Fix for disabled CH7 value triggering WP saving 2012-02-09 22:32:04 -08:00
Jason Short 4313d19bc5 2.3.1v 2012-02-09 22:22:01 -08:00
Jason Short 71d57a5371 Enabled PWM test 2012-02-09 22:22:01 -08:00
Jason Short b315e23bbd Found missing Break in Switch statement. 2012-02-09 22:22:01 -08:00
Jason Short 2335b74bc3 faster FS timer 2012-02-09 22:22:00 -08:00
Jason Short c35ad2d493 Loiter update - removed compensation curve. Did some more math and its's not worth the effort, harder to tune. 2012-02-09 22:22:00 -08:00
Jason Short 6848dc17e5 Added safety to prevent shutdown of motors during Auto-land 2012-02-09 22:22:00 -08:00
Jason Short f40d40b0f9 Acro fix - we had lost the scaling of Acro mode in 2.1. This restores that. 2012-02-09 22:22:00 -08:00
Randy Mackay fe7a0a97ab ArduCopter - CH7 - changed default to CH7_DO_NOTHING 2012-02-09 20:26:01 +09:00
levinemax 345a23273e Motor mix update for X8 (octo quad),
diagrams:
http://wiki.ardupilot-mega.googlecode.com/git/images/APM1/ACM-X8_APM14.jpg
http://wiki.ardupilot-mega.googlecode.com/git/images/APM2/FRAMES_X8.jpg
2012-02-09 03:57:40 +00:00
Randy Mackay 3517964e14 ArduCopter - Camera.pde - turn off camera pitch control (which uses channel 6) when channel 6 is being used for tuning. 2012-02-08 23:51:53 +09:00
Randy Mackay 70f91e3cc3 Arducopter - reduced rate of decent when landing using sonar 2012-02-08 22:46:32 +09:00
Randy Mackay f1a129c8ea ArduCopter - Log.pde - fixed Log_Read_Control_Tuning so that it doesn't read too many bytes. Also fixed up some comments 2012-02-05 16:56:51 +09:00
Randy Mackay 498970a948 TradHeli - tiny fix for yaw_offset. Yaw_offset is used to proactively counteract rotational force caused by changing the collective pitch (i.e. rapidly climbing or decending). There was a small bug for when the collective pitch is negative (i.e. powered decent) in which case the offset was in the incorrect direction. 2012-02-05 11:04:38 +09:00
Andrew Tridgell 1a861b3de5 allow for lower serial baud rates
not many people will use less than 9600 baud, except for those wanting
to test extreme range radios, which is what I'm trying to do :-)
2012-02-04 19:07:18 +11:00
Jason Short ef9418c2de fix issue with low throttle in air 2012-02-03 13:29:59 +00:00
Michael Oborne 151479f769 fix issue 502
to identify quad over mavlink
2012-02-03 06:53:08 +08:00
Pat Hickey dad4ee92e5 Revert all changes to ArduCopter Motors MOT mappings.
Revert "Arducopter Motors Octa: Change V frame MOT_ output ordering."

This reverts commit bdab02f408ddc5451fcb4c6390b2475d31ac657f.

Revert "hexa frame FRAME_CONFIG fixup"

This reverts commit d15e692df613cb728ec671a54dce166f6f1940a0.

Revert "Arducopter Motors Octa: revert OCTA_V_FRAME back to part of OCTA_FRAME"

This reverts commit cb0a8c62fbd07a8ae9dcb8d4fffce337ace1aa1c.

Revert "Arducopter Motors Hexa: Change ordering of MOT designations in Plus frame"

This reverts commit 120d7f9050d5ec9f8fbe02c0ed4f38621949f4ee.

Revert "Arducopter Motors Hexa: Revert HEXA_PLUS_ and HEXA_X_ to single HEXA_FRAME"

This reverts commit 7d65ec311fd2e1222a36d0b34c366e21f3869fcc.

Revert "Arducopter Frames: revert to old HEXA_FRAME and OCTA_FRAME defines."

This reverts commit 47c6e8662f4d5e8fb920f2049338541343d8d18e.

Revert "Add Max's changes for new MOT mappings. Defines new FRAME_CONFIG types."

This reverts commit 8259c90ec7cb29dedac19890cd9a4449b7399e36.
2012-02-01 10:14:46 -08:00
analoguedevices 3288b518c0 credits 2012-02-01 04:44:36 +00:00
analoguedevices 6dbcac855a Incremented version number to 2.3 2012-02-01 04:39:15 +00:00
Pat Hickey 36389cdbd8 ArduCopter Octa: fix yaw motors for Octa V.
* I based this off the APM1 Octa V diagram at
  http://code.google.com/p/arducopter/wiki/AC2_Multi
2012-01-31 19:37:49 -08:00
Pat Hickey 6a333b743a Arducopter Motors Octa: Change V frame MOT_ output ordering.
* I backed this out from Max's changes, but I'm not sure whether its correct.
2012-01-31 18:19:41 -08:00
Pat Hickey 7ca81bd2c9 hexa frame FRAME_CONFIG fixup 2012-01-31 18:19:41 -08:00
Pat Hickey a24f89fb6d Arducopter Motors Octa: revert OCTA_V_FRAME back to part of OCTA_FRAME 2012-01-31 18:19:41 -08:00
Pat Hickey 0735c2b62f Arducopter Motors Hexa: Change ordering of MOT designations in Plus frame
* This will change the output order for APM2, but not APM1.
2012-01-31 18:18:13 -08:00
Pat Hickey dbd1cc6a9f Arducopter Motors Hexa: Revert HEXA_PLUS_ and HEXA_X_ to single HEXA_FRAME 2012-01-31 18:18:13 -08:00
Pat Hickey b245265669 Arducopter Frames: revert to old HEXA_FRAME and OCTA_FRAME defines.
* HEXA_X_FRAME and HEXA_PLUS_FRAME merged back into HEXA_FRAME
* OCTA_V_FRAME merged back into OCTA_FRAME
2012-01-31 18:18:13 -08:00
Pat Hickey 0e9294538b Add Max's changes for new MOT mappings. Defines new FRAME_CONFIG types.
* HEXA_FRAME has been eliminated and changed to HEXA_X_FRAME and
  HEXA_PLUS_FRAME
* OCTA_FRAME stays the same name for X and +, but the V frame
  configuration requires new OCTA_V_FRAME name.
2012-01-31 18:18:13 -08:00
Randy Mackay b851d39eaa OptFlow - reenable OF_LOITER pid controller and reduce I term 2012-02-01 08:04:18 +09:00
Jason Short 21bd48b6c3 Loiter PIDs 2012-01-30 21:13:03 -08:00
Jason Short 8aaf88e13b tweaks to Loiter 2012-01-30 21:13:03 -08:00
Jason Short 90099d4a42 ATT tuning update 2012-01-30 21:13:03 -08:00
Jason Short f225efef9f tuning 2012-01-30 21:13:03 -08:00
Jason Short 08a9249e2b cosmetic 2012-01-30 21:13:03 -08:00
Jason Short 5934b503b8 tuning fixes 2012-01-30 21:13:03 -08:00
Jason Short 31614c39dd Cosmetic 2012-01-30 21:13:03 -08:00
Jani Hirvinen 009e87105f Minor changes for PID for jDrones motors due latest changes on control laws. 2012-01-31 09:00:31 +07:00
Jason Short 23709bafef pid_nav_lat incorrectly labeled 2012-01-29 23:02:00 -08:00
Jason Short a3862ced62 cosmetic 2012-01-29 21:55:17 -08:00
Jason Short 46e08fb46a Added more attributions 2012-01-29 21:53:44 -08:00
Jason Short ae65a0f03f removed filter. Don't need it. 2012-01-29 17:10:52 -08:00
Jason Short bf2cc6072d limiting alt hold rate error to 1m/s 2012-01-29 17:08:34 -08:00
Jason Short 02aacc454b Lowering the throttle_P values by default 2012-01-29 16:27:13 -08:00
Jason Short 650c0ed3f1 made Loiter over ride exit dependent not on speed, but centered sticks. 2012-01-29 16:15:02 -08:00
Randy Mackay 693a2cfdcd TradHeli - fix to servo limits. They had been unnecessarily limited to the collective pitch's min and max but actually there are cases (for example when the swash is leaning over 45degrees) where one servo goes well beyond the collective pitch's min or max. 2012-01-29 21:14:37 +09:00
Randy Mackay 974c825f4a Optflow - minor fix to D term defaulting 2012-01-29 21:06:41 +09:00
Jason Short 67cd412105 Landing update for better baro landing 2012-01-28 22:35:57 -08:00
Jason Short 5ab37a346c reduce test.pde size for 1280 users 2012-01-28 22:16:24 -08:00
Jason Short 7833cea9d4 2.2B6 - Please verify Heli still functions properly.
Added AC_PID lib
Updated landing code
bug fixes
2012-01-28 22:00:05 -08:00
Jason Short 295631139a formatting 2012-01-28 21:19:46 -08:00
Jason Short d1fcebb5ca Cosmetic changes
GPS LED lock waits for home_is_set to be true
2012-01-28 21:19:46 -08:00
Jason Short 326a663c6b changed tuning range 2012-01-28 21:18:43 -08:00
Randy Mackay f3a95ff3cb Arducopter - Tri - move yaw servo (channel7/motor7/CH_TRI_YAW) to mid point on startup 2012-01-28 10:13:58 +09:00
Randy Mackay 122623f64b OpticalFlow - added OF_LOITER flightmode 2012-01-28 09:27:16 +09:00
Pat Hickey 1dcd50e3be ArduCopter Tri: fix for enable_out of yaw servo, defined yaw servo for APM2 2012-01-27 07:39:01 -08:00
Randy Mackay 8dee001657 Sonar - changed default pin to A0 2012-01-26 22:50:48 +09:00
Pat Hickey 6c03307217 ArduCopter Heli: add motors_output_enable function 2012-01-25 22:41:09 -08:00
Randy Mackay 2c906b7b27 OpticalFlow - replaced PI controller with PID controller.
Modified optical flow hold to use aggregated position instead of speed.
2012-01-25 21:55:14 +09:00
Randy Mackay 4434ddf389 Optical flow - updated standard frame rate to 2000hz and increased resolution to 1600cpi 2012-01-25 21:53:20 +09:00
Jason Short 25529dec69 added loiter_d to allow users to configure alternate Loiter alg 2012-01-22 14:19:27 -08:00
Jason Short 74daadb252 Revert "test to switch loiter controls"
This reverts commit 92270371d038f246d535f0ace9fc19272c44291d.
2012-01-22 14:19:27 -08:00
Jason Short 6476ba22f2 test to switch loiter controls 2012-01-22 12:28:34 -08:00
Pat Hickey 89e11afc09 ArduCopter: Call APM_RC.enable_out for camera channels in init_camera() 2012-01-22 12:03:11 -08:00
Pat Hickey 98a90d0352 ArduCopter: Call motors_output_enable at correct spot during init 2012-01-22 12:03:11 -08:00
Pat Hickey 04a3112f33 ArduCopter: Add implementation of motors_output_enable to each motors_ frame type 2012-01-22 12:03:11 -08:00
Jason Short dd1e08a7e0 Causes Aero_SIM to fail 2012-01-22 09:34:43 -08:00
Jason Short 1d9783652a added Beta 4 tag 2012-01-21 22:15:23 -08:00
Jason Short 60e3508f7c converted to cm
Signed-off-by: Jason Short <jasonshort@mac.com>
2012-01-21 22:14:08 -08:00
Jason Short aace39e65c Converted distance gains to CM
added loiter_d for rate control, equal to old Nav_P gain
2012-01-21 22:13:57 -08:00
Jason Short fffa1af3b3 Fixed speed governor which was letting speed get to 0.
added Loiter_d to replace Nav_P for rate control
wp_distance calc now returns CM
2012-01-21 22:12:57 -08:00
Jason Short f638a4b81d recording nav_bearing rather than target bearing
recording x and y speed rather than Iterms for nav since they are always 0 now
2012-01-21 22:10:28 -08:00
Jason Short 2fa24e0557 added conversions of CM to M 2012-01-21 22:09:39 -08:00
Jason Short 7edd16e5fe Added Loiter_D to replace Nav_P for better separation of loiter and navigation tuning.
Upped Nav_P defaults to 3 based on windy flight testing
Added minimum WP speed define of 1m/s
Upped loiter_I for better wind performance - was not seeing any overshoot in logs
Made Nav_I default of 0, since we are not using it in the code.
2012-01-21 22:09:13 -08:00
Jason Short 59d1f225d5 convert command into CM from M
Making Landing boost be one at minimum to trigger better navthrottle output
2012-01-21 22:06:35 -08:00
Jason Short f3cc1121aa better default for speed governer 2012-01-21 22:05:48 -08:00
Jason Short 5cc19bbe7c slightly less filtering for less latency 2012-01-21 22:04:54 -08:00
Jason Short 9003b95499 Converted to cm for distance 2012-01-21 22:04:35 -08:00
Jason Short 8cb645f3c2 increasing the velocity near WP 2012-01-21 11:59:49 -08:00