Mirror
/
ardupilot
mirror of https://github.com/ArduPilot/ardupilot
5
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
30,980 Commits 71 Branches 509 Tags 758 MiB
Commit Graph

399 Commits

Author SHA1 Message Date
Tom Pittenger 84ce499a0d AP_Baro: remove zero-init in constructor 2016-07-11 22:11:34 -07:00
Tom Pittenger 1d81df8144 Revert "AP_Baro: coverity scan - variables not initialized in constructor" 
This reverts commit 8d2872d3ab.
 2016-07-11 22:02:41 -07:00
Tom Pittenger 8d2872d3ab AP_Baro: coverity scan - variables not initialized in constructor 2016-07-05 13:32:06 -07:00
Tom Pittenger f1f58e2026 AP_Baro: created baro drift offset accessor 2016-05-13 17:22:11 -07:00
Tom Pittenger d55050e5e3 AP_Baro: slow down the LPF for slewing to a new GND_ALT_OFFSET 
Instead of a couple seconds, make it about 15sec. This makes TECS happy by not glitching the height demand as much. When applied too fast the TECS height demand causes a large single oscillation as it chases the filter lag.
 2016-05-13 17:15:53 -07:00
Tom Pittenger 37ee3b44d2 AP_Baro: add accessor for baro drift 2016-05-13 17:15:41 -07:00
Lucas De Marchi 3c7d80a270 AP_Baro: BMP085: use a moving average of 10 samples in BMP085 
Instead of depending on the frequency accumulate() is called, use
AverageIntegralFilter with 10 samples. The data obtained by BMP085 is
too noisy with any value of OVERSAMPLING so use twice the number of
samples as currently used. Besides that now we are sure there's always
10 samples used in the average.
 2016-05-10 14:24:59 -03:00
Lucas De Marchi 8da5275b03 AP_Baro: BMP085: don't average temperature in BMP085 
The temperature readings is not subject to white noise so there's no
point in averaging its reading. Moreover since for a normal 50Hz
accumulate() / 10Hz update() it would read temperature only once per
update(), it's pointless to keep averaging and introducing rounding
error.

The temperature doesn't need to be checked as frequent as pressure, too.
The datasheet even suggests on section 3.3, page 10 to enable standard
mode and read the temperature at 1Hz. Here we reduce it to 2Hz
(considering the accumulate() function being called at 50Hz).
 2016-05-10 14:24:59 -03:00
Lucas De Marchi c5c52076ca AP_Baro: BMP085: rename private member 2016-05-10 14:24:58 -03:00
Lucas De Marchi e40b88aa70 AP_Baro: BMP085: use DigitalSource interface in BMP085 
Use the DigitalSource interface rather than going through the "static"
interface hal.gpio provides
 2016-05-10 14:24:58 -03:00
Lucas De Marchi 56fa1b6214 AP_Baro: BMP085: change oversampling in BMP085 without EOC 
If we don't have EOC pin and assuming the accumulate() function is
called at 50Hz (or higher) we would take very few samples to accumulate
before the update is called. That's because since we have to wait 26ms
to get a sample and we calling accumulate() every 20ms, half of the
times it will return without getting anything.  So we will
be using 2 or 3 samples only to average.

If we don't have EOC, use OVERSAMPLING=2 which gives us more noise, but
that we can filter out by using measurements to average. When we have
EOC we don't need it because most of the time the conversion will take
less than 20ms: I'm getting 16ms on most of them while bench-testing.
 2016-05-10 14:24:58 -03:00
Lucas De Marchi 37e2f6c52e AP_Baro: BMP085: allow to easily change oversampling in BMP085 
This way it's possible to easily change it if a board requires.
 2016-05-10 14:24:58 -03:00
Andrew Tridgell 8b7bf5cf7a AP_Baro: allow setHIL to set last update time 2016-05-07 18:27:21 +10:00
Andrew Tridgell 0b71652afc AP_Baro; allow for exact replay of baro data 2016-05-07 18:27:20 +10:00
Andrew Tridgell 8a987bf67d AP_Baro: removed filtering of baro data in HIL/SITL 
this was just causing lag in replay and doesn't actually help in SITL
 2016-05-07 18:27:18 +10:00
Don Gagne cae7ea0d13 Add @Volatile, @ReadOnly support 2016-03-17 10:58:05 +11:00
Andrew Tridgell 0a72c2bbd5 AP_Baro: prevent bad ground pressure from making a board unbootable 2016-02-23 16:34:06 +11:00
Lucas De Marchi f1ade970a3 AP_Baro: MS5611: Use AP_HAL::Device abstraction 
This allows to share almost all the I2C/SPI code and remove the
AP_Serial abstraction since that is now handled by AP_HAL itself.
 2016-02-16 19:49:09 -02:00
Lucas De Marchi b05954660a AP_Baro: BMP085: use I2CDevice interface 2016-02-16 19:49:09 -02:00
Tom Pittenger f435c5ee50 AP_Baro: tolerate GND_ALT_OFFSET step inputs 
large inputs make the EKF angry, this will allow the param update to slew over a few seconds
 2016-02-08 21:13:58 -08:00
Lucas De Marchi 56e4de0bdd AP_Baro: MS56XX: remove initialization to 0 from constructor 2016-02-01 14:18:50 -02:00
Lucas De Marchi 9d5fb97819 Global: rename enum SPIDevice to SPIDeviceType 
Free the SPIDevice name so to have a consistent name for I2C/SPI device
classes.
 2016-02-01 14:18:50 -02:00
Gustavo Jose de Sousa c2e3f05dbf waf: ardupilotwaf: prefix build context methods with ap_ 
It helps to distinguish between things from waf and things from ardupilotwaf.
 2016-01-22 20:10:29 -02:00
Gustavo Jose de Sousa 3d22490397 waf: examples: use methods from bld instead of ardupilotwaf 2016-01-22 20:10:29 -02:00
Julien BERAUD d15097f3fc AP_Baro_MS5611: Support for timesliced timers 
fallback if current scheduler doesn't support it
 2016-01-18 16:57:48 -02:00
Gustavo Jose de Sousa d281067bcc waf: make example binaries be placed in 'examples' dir 
This commit makes examples' wscripts use ardupilotwaf.example() instead of
ardupilot.program().
 2016-01-15 16:46:41 -02:00
Jonathan Challinger dcfc95fadf AP_Baro: fix example build 2015-12-29 10:46:35 -08:00
Lucas De Marchi a096703b06 Global: don't link with AP_Progmem 
AP_Progmem is not used anymore.
 2015-12-27 15:58:12 -02:00
Andrew Tridgell ff44a63007 AP_Baro: added QURT driver 2015-12-27 16:21:25 +11:00
Andrew Tridgell 1f4e503d91 AP_Baro: added qflight driver 2015-12-27 16:12:27 +11:00
Andrew Tridgell ef83f39029 AP_Baro: renamed _C* vars to avoid conflict with qurt 2015-12-20 17:55:39 +11:00
Lucas De Marchi 5b1769cd2b AP_Baro: remove unused AP_ADC_AnalogSource 2015-12-03 13:32:42 +11:00
Caio Marcelo de Oliveira Filho 6e7b73610d waf: add waf support 2015-12-03 07:54:30 +11:00
Lucas De Marchi 8eee888b3e AP_Baro: BMP085: move data-ready macro to a method 2015-12-02 10:40:50 +11:00
Lucas De Marchi c5e97129c1 AP_Baro: BMP085: follow coding style 
- Spacing changes and variable renames to follow coding style
 - No need to initialize variables to 0, it's already done by our
   global new operator.
 2015-12-02 10:40:50 +11:00
Lucas De Marchi 81a298c9c8 AP_Baro: reduce header scope 
We don't need to expose to other libraries how each backend is
implemented. AP_Baro.h is the main header, included by other libraries.

Instead of including each backend in the main header, move them to where
they are needed. Additionally standardize the order and how we include
the headers.

The advantages are:
	- Internals of each backend is not exposed outside of the
	  library
	- Faster incremental builds since we don't need to recompile
	  whoever includes AP_Baro.h because a backend changed
 2015-12-02 10:40:50 +11:00
Lucas De Marchi 30f631de8f AP_Baro: MS5637: fix CRC check 
The configuration of MS5637 is different from MS5611 in 2 ways:

    - The PROM is of 112 bytes rather than 128
    - The CRC is located in the first MSB of the first word, not the
      last one

For CRC calculation we also need to zero out the last (missing) word.

This renames _check_crc() to _read_prom(), which returns false when the
PROM doesn't contain valid data. It also makes it virtual so MS5637 can
override it. This also moves the PROM read to be all in the same place
rather than split between the CRC field and coefficient fields. Finally
calculate_crc() is renamed to crc4() to be shorter and add info on what
it does.
 2015-12-02 10:38:09 +11:00
José Roberto de Souza 7457588d7c AP_Baro: Move initialisation code from MS56XX constructor to init() 
On MS5637 we will need to override the method to read and calculate the
PROM's crc. Thus we need a 2-phase init.

It also makes the constructor of AP_Baro_MS56XX protected since only the
derived classes should instantiate the base one.
 2015-12-02 10:38:09 +11:00
José Roberto de Souza 29791c9cec AP_Baro: Make _check_crc more readable 2015-12-02 10:38:09 +11:00
Caio Marcelo de Oliveira Filho 8cce3067f4 AP_Baro: examples use millis/micros/panic functions 2015-11-20 12:29:38 +09:00
Caio Marcelo de Oliveira Filho 5a280838f8 AP_Baro: use millis/micros/panic functions 2015-11-20 12:29:31 +09:00
Lucas De Marchi 977f6aaf15 AP_Baro: MS5611: remove empty statement 2015-11-11 13:48:48 +11:00
Lucas De Marchi 94d01934f7 AP_Baro: MS5611: reduce OSR to 1024 
This is the same change as done in PX4:

	This reduces self-heating of the sensor which reduces the amount
	of altitude change when warming up. Apparently some individual
	sensors are severely affected by this.

	Unfortunately it raises the noise level, but Paul is confident
	it won't be a significant issue.
 2015-11-11 13:48:48 +11:00
Andrew Tridgell 840c9e65bb AP_Baro: don't notify the GCS of new pressure reference too often 2015-11-09 14:34:07 +11:00
Peter Barker 1b13315092 AP_Baro: notify GCS of calibration 2015-11-09 09:23:20 +11:00
Lucas De Marchi 8eef58a8c2 AP_Baro: remove check for AVR CPUs 
Remove the checks for HAL_CPU_CLASS > HAL_CPU_CLASS_16 and
HAL_CPU_CLASS >= HAL_CPU_CLASS_75. Corresponding dead code will be
removed on separate commits.
 2015-11-04 12:14:14 +11:00
Lucas De Marchi 4bd8b2ae35 AP_Baro: remove checks for HAL_BOARD_APM2 and HAL_BOARD_APM1 2015-11-04 12:14:11 +11:00
Lucas De Marchi 831d8acca5 Remove use of PROGMEM 
Now variables don't have to be declared with PROGMEM anymore, so remove
them. This was automated with:

    git grep -l -z PROGMEM | xargs -0 sed -i 's/ PROGMEM / /g'
    git grep -l -z PROGMEM | xargs -0 sed -i 's/PROGMEM//g'

The 2 commands were done so we don't leave behind spurious spaces.

AVR-specific places were not changed.
 2015-10-30 14:35:16 +09:00
Lucas De Marchi 2c38e31c93 Remove use of PSTR 
The PSTR is already define as a NOP for all supported platforms. It's
only needed for AVR so here we remove all the uses throughout the
codebase.

This was automated with a simple python script so it also converts
places which spans to multiple lines, removing the matching parentheses.

AVR-specific places were not changed.
 2015-10-30 14:35:04 +09:00
Lucas De Marchi 386547427d AP_Baro: support MS5611 on second i2c bus 2015-10-22 12:04:52 +11:00
wsilva32 da9118fbd0 AP_Baro: average SITL baro measurements using update() 2015-10-21 10:25:08 +11:00
Lucas De Marchi 4d3229daa2 AP_Baro: remove check for HAL_CPU_CLASS 
We don't support HAL_CPU_CLASS <= HAL_CPU_CLASS_16 anymore. This makes
BARO_MAX_INSTANCES and BARO_MAX_DRIVERS constant for all supported
boards.
 2015-10-21 10:05:18 +11:00
Caio Marcelo de Oliveira Filho 24178c3e10 AP_Baro: remove unnecessary includes in example 2015-10-21 09:16:10 +11:00
Caio Marcelo de Oliveira Filho ec52df991c build: compile only the HAL files needed by the board 
Instead of requiring every program to specify the HAL related modules,
let the build system do it (in practice everything we compiled depended
on HAL anyway). This allow including only the necessary files in the
compilation.
 2015-10-21 09:16:07 +11:00
Caio Marcelo de Oliveira Filho 2e464a53c2 AP_HAL: make code not depend on concrete HAL implementations 
The switching between different AP_HAL was happening by giving different
definitions of AP_HAL_BOARD_DRIVER, and the programs would use it to
instantiate.

A program or library code would have to explicitly include (and depend)
on the concrete implementation of the HAL, even when using it only via
interface.

The proposed change move this dependency to be link time. There is a
AP_HAL::get_HAL() function that is used by the client code. Each
implementation of HAL provides its own definition of this function,
returning the appropriate concrete instance.

Since this replaces the job of AP_HAL_BOARD_DRIVER, the definition was
removed.

The static variables for PX4 and VRBRAIN were named differently to avoid
shadowing the extern symbol 'hal'.
 2015-10-21 09:16:07 +11:00
José Roberto de Souza c53e9d1ff0 AP_Baro: Fix typo 2015-10-16 10:05:03 +11:00
José Roberto de Souza 9a98eb35fc AP_Baro: Add MS5637 over I2C to init() 2015-10-16 10:05:03 +11:00
José Roberto de Souza c373ce34d1 AP_Baro: MS56XX: Some minor fixes 2015-10-16 10:05:03 +11:00
José Roberto de Souza d9931b5f34 AP_Baro: Add support to MS5637 
As AVR2560 is not supported anymore and do integer operations is
usually faster than float-point the _calculate() implementation was
done using only integer operations and as more close to what
datasheet says.
 2015-10-16 10:05:03 +11:00
raspilot 831bb554e7 AP_Baro_MS5611: suspend timer when init to prevent other SPI drivers grabbing the bus. 2015-10-02 09:54:55 +10:00
mirkix ba4db34c83 AP_Baro: Prevent busy waiting 2015-10-02 09:49:12 +10:00
Julien BERAUD 3b5d73b1fe AP_Baro_MS5611: Fix state machine in case of error 
If there is a read error, reading from the adc will return 0 but moreover,
we need to re-initiate a read or else we are stuck forever.

From MS5611-01BA03 datasheet, p. 10, CONVERSION SEQUENCE:
"After the conversion, using ADC read command the result is clocked out with the MSB first.
If the conversion is not executed before the ADC read command, or the ADC read command is
repeated, it will give 0 as the output result."
 2015-09-23 09:19:22 +10:00
Andrew Tridgell a5462fec0b AP_Baro: allow selection of primary barometer and add 3rd baro 
this is useful for external I2C barometers on a PH2
 2015-09-14 14:27:41 +10:00
Gustavo Jose de Sousa bcd5dff774 AP_Baro: MS56XX: do not change change state on error 
If we have an error in the SPI or I2C transaction we should not change
the state. Otherwise we might read a temperature when the sensor is
reporting pressure and vice-versa.
 2015-09-01 20:26:06 +10:00
Gustavo Jose de Sousa 1f29e18375 AP_Baro: make AP_SerialBus::write() return success or failure for MS56XX 2015-09-01 20:26:05 +10:00
Tom Pittenger 749c0c190f AP_Baro - fix BARO_ALT_OFFSET param 
This param seems to have been un-implemented. This is putting it back in. Adds a meter offset to the calculated altitude form the baro sensors.
Also changes it from int8 to float
 2015-08-26 13:16:05 +10:00
Gustavo Jose de Sousa f18802bc46 AP_Baro: standardize inclusion of libaries headers 
This commit changes the way libraries headers are included in source files:

 - If the header is in the same directory the source belongs to, so the
 notation '#include ""' is used with the path relative to the directory
 containing the source.

 - If the header is outside the directory containing the source, then we use
 the notation '#include <>' with the path relative to libraries folder.

Some of the advantages of such approach:

 - Only one search path for libraries headers.

 - OSs like Windows may have a better lookup time.
 2015-08-11 16:28:42 +10:00
Grant Morphett 312184dd13 AP_Baro: coverity fixes - add param init in constructor 2015-07-30 12:37:08 +10:00
Randy Mackay 5732a6a144 Baro: update climb rate only if healthy 2015-07-29 16:32:49 +09:00
Julien BERAUD d407737434 AP_Baro: added MS5607 support 2015-07-10 16:46:29 +10:00
Andrew Tridgell 282efe2d57 AP_Baro: fixed example to run accumulate at 50Hz 2015-07-10 09:59:35 +10:00
Andrew Tridgell 4368f922a3 AP_Baro: convert example from .pde to .cpp 2015-06-01 16:58:10 +10:00
Lucas De Marchi df5652fa87 AP_Baro: use functor macros 
Functor is not yet being used but let's make is macro fallback to the
previous Delegate implementation for easy of transition between the two.
 2015-05-26 13:46:52 +10:00
ziltoid2 23787cf695 AP_Baro: use ground_temperature instead of calibration_temperature for alt calculation 2015-05-20 11:42:21 +10:00
Andrew Tridgell 48fb7f8159 AP_BARO: revert AP_Math class change 2015-05-05 13:27:05 +10:00
Tom Pittenger 0b29848277 AP_Baro: compiler warnings: apply is_zero(float) or is_equal(float) 2015-05-05 13:26:56 +10:00
Andrew Tridgell 7d9d594283 AP_Baro: fix for HAL_SITL rename 2015-05-05 09:45:55 +10:00
Randy Mackay 55298a4c73 Baro: fix example sketch 2015-05-02 17:25:44 +09:00
Randy Mackay 1b381b5675 Baro: get_air_density_ratio gets div-by-zero check 2015-04-29 14:36:20 +09:00
Jonathan Challinger f381ef93e8 AP_Baro: add get_air_density_ratio 2015-04-29 14:36:10 +09:00
Tom Pittenger 4191c44bbd Baro: fix compile warning re member init order 2015-04-24 14:15:11 +09:00
Andrew Tridgell 2e9d2e6449 AP_Baro: load only HIL backend for hil_mode 2015-03-13 22:52:55 +11:00
Andrew Tridgell d040318014 AP_Baro: removed unused define 2015-03-13 18:46:17 +11:00
Randy Mackay 4e7d92094c Baro: remove glitch detection 2015-03-13 16:40:29 +09:00
Andrew Tridgell 1f70b34cbc AP_Baro: fixed baro startup on PXF cape 2015-03-13 13:48:41 +11:00
Andrew Tridgell beeb9173ea AP_Baro: change for new PX4 paths 2015-02-14 12:25:43 +11:00
Andrew Tridgell ac3dd87790 AP_Baro: added hil_mode support 2015-02-10 09:53:30 +11:00
Randy Mackay bb4204c045 Baro: fix example sketch 2015-01-28 17:15:37 +09:00
Randy Mackay c93e7a69a7 Baro: init external_temperature in constructor 2015-01-12 13:56:35 +09:00
Andrew Tridgell b1d8df3d54 AP_Baro: only allow calibrated sensors to be used 2015-01-09 12:59:01 +11:00
Andrew Tridgell 3320dfd7fa AP_Baro: fixed ms5611 spelling error 2015-01-09 11:59:49 +11:00
Andrew Tridgell 0a8677b3e2 AP_Baro: fixed build after rebase with all_healthy() 2015-01-09 11:51:52 +11:00
Andrew Tridgell 1c2a6deaaf AP_Baro: added all_healthy() method 2015-01-09 11:51:51 +11:00
Andrew Tridgell 8359c082ca AP_Baro: fixed baro on NavIO 
don't use the 1kHz timer as it conflicts with other I2C devices
 2015-01-09 11:51:51 +11:00
Andrew Tridgell 197c09fcd8 AP_Baro: added num_instances() API 2015-01-09 11:50:56 +11:00
Andrew Tridgell f1891cea1f AP_Baro: BMP085 driver done, but untested 2015-01-09 11:50:54 +11:00
Andrew Tridgell 5bb57a31f7 AP_Baro: split into frontend/backend 
this allows for support of multiple sensors on a board
 2015-01-09 11:50:54 +11:00
Staroselskii Georgii 43c88c37eb AP_Baro: fixed MS5611 initialisation in order to get rid off conflicts with other I2C devices 2015-01-07 08:41:13 +11:00
Randy Mackay ddda0d52ce Baro: reorder declaration to fix compiler warning 
No functional change
 2014-12-11 13:06:24 +09:00
Andrew Tridgell e45522f51d AP_Baro: fixed example build 2014-11-28 10:40:43 +11:00
Andrew Tridgell d404cc6542 AP_Baro: add set_external_temperature() 
this allows the use of an external temperature sensor for calibration
purposes, such as the sensor built in to the digital airspeed sensor.

The main affect this has is on the EAS2TAS calculation

The get_calibration_temperature() is used to choose either an external
temperature or an internal one. If an internal one is used then it is
clamped at no higher than 25 degrees C, to prevent hot electronics
on startup affecting altitude scaling and EAS2TAS
 2014-11-12 13:36:01 +11:00
Andrew Tridgell 8b794602d1 AP_Baro: make get_temperature() a const function 2014-11-12 13:36:01 +11:00
Randy Mackay 67690553c5 BaroGlitch: add reset method 2014-11-09 13:34:15 -08:00
Randy Mackay 3a81732721 Baro: minor param description updates 2014-10-14 12:42:27 +09:00
Andrew Tridgell 5280d8936d AP_Baro: remove usage of hrt_absolute_time() 
use a single time base in all code
 2014-08-20 08:41:15 +10:00
Andrew Tridgell d01fa3bfbd AP_Baro: prevent reading the MS5611 too fast 
setup the timer start after we've started the conversion to prevent
reading faster than the MS5611 is able to produce values
 2014-08-19 21:16:13 +10:00
Randy Mackay fd5dee96e4 BaroGlitch: check baro health after alt calculation 
Also correct type of distance_cm internal variable
 2014-08-14 16:03:33 +09:00
Randy Mackay 424a65663a Baro: init members to resolve compiler warning 2014-08-14 16:03:30 +09:00
Randy Mackay 53b073148b BaroGlitch: use baro healthy() 2014-08-14 16:03:21 +09:00
Randy Mackay 78b1bf8282 Baro: example sketch to use healthy() function 2014-08-14 16:03:15 +09:00
Randy Mackay 76634ee8c3 Baro_PX4: use healthy flag 2014-08-14 16:03:12 +09:00
Randy Mackay d29fe51cb3 Baro_VRBrain: use healthy flag 2014-08-14 16:03:09 +09:00
Randy Mackay 24db492131 Baro_MS5611: use healthy flag 2014-08-14 16:03:06 +09:00
Randy Mackay 72f6985bd8 Baro_HIL: use healthy flag 2014-08-14 16:03:04 +09:00
Randy Mackay fdb38dec5f Baro_BMP085: use healthy flag 2014-08-14 16:03:02 +09:00
Randy Mackay 330d883f97 Baro: add altitude sanity check 
healthy flag made protected
healthy accessor fn added which also check latest calculated altitude
was ok
 2014-08-14 16:02:59 +09:00
Randy Mackay e9fbea9497 Baro: make get_altitude_difference const 2014-08-14 16:02:55 +09:00
Randy Mackay af28b74944 Baro_BMP085: init members to resolve compiler warnings 2014-08-14 11:27:29 +09:00
Andrew Tridgell a400cbc922 AP_Baro: fixed example build 2014-08-13 21:46:14 +10:00
Mikhail Avkhimenia 83bbee491c AP_Baro_MS5611: add address switch for Navio board 2014-08-12 22:09:29 +10:00
Randy Mackay 5d4e019397 BaroGlitch: increase max accel to 15m/s/s 2014-08-09 15:47:52 +09:00
Andrew Tridgell 6ebff35fe2 AP_Baro: don't include I2C MS5611 on APM1 either 2014-08-03 17:17:20 +10:00
Randy Mackay fe24721218 BaroGlitch: increase default ok distance to 5m 
When taking off some copters hove a sudden baro altitude dip of 4m
 2014-08-02 11:43:06 +09:00
Randy Mackay c68d4fdfcb BaroGlitch: init members to resolve compiler warning 2014-08-01 14:07:34 +09:00
Randy Mackay 728da12441 BaroGlitch: remove debug 2014-07-29 22:05:09 +09:00
Andrew Tridgell c538cc0665 AP_Baro: fixed example build 2014-07-29 21:04:26 +10:00
Randy Mackay 2289b98d34 Baro_Glitch: initial version of baro glitch protection 
Based on GPS Glitch protection library
 2014-07-28 22:16:12 +09:00
Andrew Tridgell a458f1bf5f AP_Baro: minor improvements to Baro HIL code health check 2014-07-24 21:46:06 +10:00
Andrew Tridgell 2b3d17d955 AP_Baro: fixed APM1 build 2014-07-14 09:50:17 +10:00
Andrew Tridgell be02f0c34f AP_Baro: work around occasional 0 values from MS5611 
this was seen on the PXF board. It isn't yet known why it happens
 2014-07-14 09:44:36 +10:00
Andrew Tridgell b0ab2671cd AP_Baro: removed old device specific example code 
not needed any more
 2014-07-14 09:44:36 +10:00
Andrew Tridgell 028e2e34f1 AP_Baro: added generic baro test sketch 2014-07-14 09:44:36 +10:00
Andrew Tridgell f73ec95c39 AP_Baro_MS5611: added PROM CRC checking 
disabled on APM2 to save flash space
 2014-07-14 09:44:35 +10:00
Víctor Mayoral Vilches 8a85f8d6d2 AP_Baro_MS5611_test: Add HAL specific code. 2014-07-14 09:29:53 +10:00
Víctor Mayoral Vilches de58df6371 AP_Baro_MS5611_test: Add block for APM2-code 2014-07-14 09:29:45 +10:00
Víctor Mayoral Vilches 9797867067 AP_Baro_MS5611: Fix the test code so that compiles. 
Add HAL_BOARD_LINUX and HAL_BOARD_ERLE compatibility.
 2014-07-14 09:02:47 +10:00
Andrew Tridgell 74c3b404ee AP_Baro: avoid some float conversion warnings 2014-07-08 20:26:54 +10:00
Andrew Tridgell e118984c26 AP_Baro: save some flash and memory on APM2 
we don't need the I2C MS5611 driver
 2014-07-08 14:21:42 +10:00
Andrew Tridgell 3705c90b8e AP_Baro: fix for HAL_GPIO_* 2014-06-02 10:42:36 +10:00
Andrew Tridgell 41dd280739 AP_Baro: expose get_altitude_difference() 
this is useful for pressure altitude calculations
 2014-04-11 16:34:02 +10:00
Emile Castelnuovo f4784fe6a1 AP_Baro: new files for VRBRAIN board 2014-04-08 16:19:19 +10:00
Andrew Tridgell d3d71d597c AP_Baro: fixed example build 2014-03-19 12:14:05 +09:00
Andrew Tridgell 63234d4c22 AP_Baro: fixed linux build of BMP085 driver 2014-03-07 09:33:43 +11:00
Andrew Tridgell b2bd81f262 AP_Baro: added alternative setHIL interface 
uses pressure and temperature for better log replay
 2014-02-18 09:25:07 +11:00
Andrew Tridgell 3af38a778d AP_Baro: fixed example build 2014-02-15 06:40:15 +11:00
Randy Mackay bb715424ee Baro: fix BMP085 example sketch 2014-02-15 06:09:08 +11:00
Andrew Tridgell 6964529124 AP_Baro: _calculate can be private 2014-02-15 05:48:24 +11:00
Andrew Tridgell 2cd781997f AP_Baro: changed HIL driver to use floats and better handle starup 2014-02-15 05:48:18 +11:00
Andrew Tridgell 5e3c4441dc AP_Baro: use HAL_CPU_CLASS in baro driver 2013-12-31 10:28:37 +11:00
Andrew Tridgell 42eba615b4 AP_Baro: fixed example build 2013-12-17 11:51:37 +11:00