* Update launch files to support multi-video stream in SITL
* Pass extra args to jinja_gen.py inside gazebo_sitl_multiple_run.sh to enable multi-video streaming
The windowed mode has been added for Windows targets originally. It gets very often incorrectly detected and slows down flashing considerably. This even applies to serial links. We are disabling it now in most circumstances.
- sitl_gazebo in PX4/Firmware (5868463d06): 563f0876a5
- sitl_gazebo current upstream: 4043287bbe
- Changes: 563f0876a5...4043287bbe
4043287 2020-12-20 Silvan Fuhrer - tiltrotor: increase wing area to 0.5 per side (#678)
f004811 2020-12-20 JaeyoungLim - Update mavsdk version for SITL tests (#673)
- sitl_gazebo in PX4/Firmware (90f61c2f9a): 19981d61cf
- sitl_gazebo current upstream: 563f0876a5
- Changes: 19981d61cf...563f0876a5
563f087 2020-12-17 JaeyoungLim - Fix tiltrotor model (#675)
0e2d63a 2020-12-17 JaeyoungLim - Fix wind transmormations for motor model (#674)
e5d0d65 2020-12-13 JaeyoungLim - Update container versions for tests (#672)
bccb487 2020-12-12 BazookaJoe1900 - mavlink_interface: rename serial link related function to include 'serial' (#670)
This commit removes the readarray command from the Tools/sitl_run.sh.
This fixes the issue where SITL was not able to run due to readarray not being available on macOS
* Add typhoon h480 support to gazebo multiple sim
This commit adds support for the typhoon_h480 model for the
gazebo_sitl_multiple_run.sh script.
* Update sitl_gazebo to latest version
- switch to python3
- run_nsh_cmd.py return error if command fails
- decrease timeout in checking for output
- Jenkins hardware tests tolerate certain command failures that aren't available on all boards (flash constrained, etc)
- sitl_gazebo in PX4/Firmware (79ad5eab34b76fbe54c2056974230a122362a62f): 487f6283f4
- sitl_gazebo current upstream: ee7661eeab
- Changes: 487f6283f4...ee7661eeab
ee7661e 2020-11-06 Julian Oes - cmake: don't link to protobuf
- ekf2 can now run in multi-instance mode (currently up to 9 instances)
- in multi mode all estimates are published to alternate topics (eg estimator_attitude instead of vehicle_attitude)
- new ekf2 selector runs in multi-instance mode to monitor and compare all instances, selecting a primary (eg N x estimator_attitude => vehicle_attitude)
- sensors module accel & gyro inconsistency checks are now relative to the mean of all instances, rather than the current primary (when active ekf2 selector is responsible for choosing primary accel & gyro)
- existing consumers of estimator_status must check estimator_selector_status to select current primary instance status
- ekf2 single instance mode is still fully supported and the default
Co-authored-by: Paul Riseborough <gncsolns@gmail.com>
- sitl_gazebo in PX4/Firmware (dfbaf6607a): c3b15b7c9b
- sitl_gazebo current upstream: 6b9c8f15c2
- Changes: c3b15b7c9b...6b9c8f15c2
6b9c8f1 2020-10-10 Daniel Agar - mavlink interface round double sim time when converting to microseconds
b4cebfc 2020-10-09 JaeyoungLim - Support HIL configurations for generated models (#625)
b4d2d58 2020-10-09 Daniel Agar - mavlink interface poll until actuator received (#631)
* Add techpod SITL target
This adds a SITL target forthe techpod fixedwing model
* Update sitl_gazebo submoudle
This submodule update includes the techpod UAV model
* Add jsbsim bridge to enable jsbsim for px4 SITL/HIL on jsbsim
This is a PX4 HIL/SITL integration into JSBSim. JSBSim is an open source flight dynamics model (http://jsbsim.sourceforge.net/)
Currently there are three models available which is the rascal, quadrotor_x, hexarotor_x integrated into the bridge.
The simulation can be run with the firmware with the following command for example
```
make px4_sitl jsbsim_rascal
```
The visualization is done flightgear and is done by the bridge sending UDP packets to flightgear. To disable the visualization `HEADLESS=1` when running the make command.
The simulation can be configured through the configuration files under the `config` directory through a xml file. Senor configurations, The xml file name should match the name of the model.
* Update Tools/sitl_run.sh
Co-authored-by: Beat Küng <beat-kueng@gmx.net>
Co-authored-by: Beat Küng <beat-kueng@gmx.net>
- fix gazebo SITL debug
- now prompts you to select vehicle
- devcontainer.json container support https://code.visualstudio.com/docs/remote/containers
- this allows you to jump straight into working within a container (px4-dev-nuttx) on a fresh machine
- also helps with Codespaces https://github.com/features/codespaces
- plugin updates
- cpp extension pack, spell checking, CTest support
- cleanup intellisense
- the backup tag parser was a resource hog and didn't work very well
- fix problemMatcher support so that you can click on a build failure
- sitl_gazebo in PX4/Firmware (ac732cdeba): 78bba3f25e
- sitl_gazebo current upstream: 9d2b19784c
- Changes: 78bba3f25e...9d2b19784c
9d2b197 2020-09-12 JaeyoungLim - Use jinja templates for standard_vtol and plane model (#590)
01587e6 2020-09-12 Lorenz Meier - Include GLib2 properly The previous approach did not actually search for glib2 in the system but hardcoded the name.
e49fac5 2020-09-12 bazooka joe - cleanups: rename class vars to be with underscore
6fb9bd9 2020-09-12 bazooka joe - move initializers to h file
29999c6 2020-09-12 JaeyoungLim - Update boat gps sensor (#595)
a208640 2020-09-09 petertheprocess - fix the rudder deflection bug. (#588)
- inconsistency checks now run continuously instead of only preflight
- keep inconsistencies for all sensors
- add per sensor data validator state as overall health flag
* [WIP] i2c_spi_buses: add '-q' for quiet startup flag
And enable for optional board sensors.
* ROMFS: rc.sensors try starting all optional I2C sensors quietly
Co-authored-by: Daniel Agar <daniel@agar.ca>
This should prevent the race between gzserver and gz model and fix the
integration tests which sometimes timeout because the model is not
spawned correctly.
This patch also changes the shebang to what's generally recommended.
If `make px4_sitl_default` is run, and not `make px4_sitl_default gazebo` then each model instance will throw the following errors:
```
[Err] [Plugin.hh:178] Failed to load plugin libgazebo_gps_plugin.so: libgazebo_gps_plugin.so: cannot open shared object file: No such file or directory
[Err] [Plugin.hh:178] Failed to load plugin libgazebo_multirotor_base_plugin.so: libgazebo_multirotor_base_plugin.so: cannot open shared object file: No such file or directory
[Err] [Plugin.hh:178] Failed to load plugin libgazebo_motor_model.so: libgazebo_motor_model.so: cannot open shared object file: No such file or directory
[Err] [Plugin.hh:178] Failed to load plugin libgazebo_motor_model.so: libgazebo_motor_model.so: cannot open shared object file: No such file or directory
[Err] [Plugin.hh:178] Failed to load plugin libgazebo_motor_model.so: libgazebo_motor_model.so: cannot open shared object file: No such file or directory
[Err] [Plugin.hh:178] Failed to load plugin libgazebo_motor_model.so: libgazebo_motor_model.so: cannot open shared object file: No such file or directory
[Err] [Plugin.hh:178] Failed to load plugin libgazebo_groundtruth_plugin.so: libgazebo_groundtruth_plugin.so: cannot open shared object file: No such file or directory
[Err] [Plugin.hh:178] Failed to load plugin libgazebo_magnetometer_plugin.so: libgazebo_magnetometer_plugin.so: cannot open shared object file: No such file or directory
[Err] [Plugin.hh:178] Failed to load plugin libgazebo_barometer_plugin.so: libgazebo_barometer_plugin.so: cannot open shared object file: No such file or directory
[Err] [Plugin.hh:178] Failed to load plugin libgazebo_mavlink_interface.so: libgazebo_mavlink_interface.so: cannot open shared object file: No such file or directory
[Err] [Plugin.hh:178] Failed to load plugin libgazebo_imu_plugin.so: libgazebo_imu_plugin.so: cannot open shared object file: No such file or directory
```
- sitl_gazebo in PX4/Firmware (f4d7052bec): 629e5f5c23
- sitl_gazebo current upstream: ce1eca2bd0
- Changes: 629e5f5c23...ce1eca2bd0
ce1eca2 2020-07-19 Daniel Leonard Robinson - New vehicle type: Airship (#490)
df186d2 2020-07-18 TSC21 - use 'EnableC++XX' and remove duplicated compiler sets
60e5d4e 2020-07-18 TSC21 - remove the check for the 'px4' binary (it's never found since it's built in parallel with sitl_gazebo)
a3b5c5e 2020-07-19 JaeyoungLim - Fix moment calculation (#545)
07820ee 2020-07-19 JaeyoungLim - Fix gimbal imu sensors intefering with each other (#549)
- Spaces -> tabs.
- Remove "brew install python" because it's already a dependency of the
px4-dev tap.
- Remove "brew install ccache" as we can also add it to the px4-dev tap.
- Don't try to update pip installation, it works fine as is.
- Install pip dependencies as user, no need for system-wide install.
- sitl_gazebo in PX4/Firmware (38588f0c37): 309f7b0ace
- sitl_gazebo current upstream: 1af7e29dbb
- Changes: 309f7b0ace...1af7e29dbb
1af7e29 2020-06-25 JaeyoungLim - Do not validate r1_rover
5e8ddfb 2020-06-25 Benjamin Perseghetti - fixes for R1 SDF https://github.com/PX4/sitl_gazebo/issues/533 (#534)
726c066 2020-06-23 Supakorn Suttiruang - Remove the incorrect force generated by moment (#532)
Co-authored-by: PX4 BuildBot <bot@px4.io>
- sitl_gazebo in PX4/Firmware (6b343c1f5e): 97106007eb
- sitl_gazebo current upstream: 846190e8a3
- Changes: 97106007eb...846190e8a3
846190e 2020-06-18 Daniel Agar - cmake set build type and C/C++ standard
1cd16d7 2020-06-18 JaeyoungLim - Set GPS utc time to use utc time (#522)
- remove all remaining IOCTLs for accel and gyro and handle all calibration entirely in sensors module with parameters
- sensor_accel and sensor_gyro are now always raw sensor data
- calibration procedures no longer need to first clear existing values before starting
- temperature calibration (TC) remove all scale (SCL) parameters
- gyro and baro scale are completely unused
- regular accel calibration scale can be used (CAL_ACC*_xSCALE) instead of TC scale
- sitl_gazebo in PX4/Firmware (39a33a35ae): 20e8dbe115
- sitl_gazebo current upstream: 3ba325b00f
- Changes: 20e8dbe115...3ba325b00f
3ba325b 2020-06-03 Julian Oes - geotagged_images: actually report number of images
92453d1 2020-05-21 JaeyoungLim - Cleanup
9aef888 2020-05-21 JaeyoungLim - Translate yaw to point at the right direction
* uORB orb_stat() and update(uint64_t *time, void *dst) are now obsolete and have been deleted
* mavlink messages add more advertised checks in streams get_size() check to improve data rate calculation across different scenarios
- sitl_gazebo in PX4/Firmware (88c9761f1f): 8569aec5bb
- sitl_gazebo current upstream: 458e58f797
- Changes: 8569aec5bb...458e58f797
458e58f 2020-03-10 JaeyoungLim - Fix sweep cosine (Continuing #302) (#429)
ea2568d 2019-12-27 JaeyoungLim - Increase rudder angle limit
8b905c9 2019-12-27 JaeyoungLim - Add rudder control to sitl
08f8e6f 2020-03-10 Jan-Hendrik Ewers - Update README.md
de10edd 2020-03-10 iwishiwasaneagle - FixesPX4/sitl_gazebo#424 for arch and ubuntu
4f596be 2020-03-10 Christian Clauss - Remove unused function isstring() in scripts/names.py (#346)
89db01c 2020-03-09 Matej Frančeškin - Handle MAV_CMD_SET_CAMERA_MODE
dae26ba 2020-03-08 JaeyoungLim - Handle videostream info and status
c13057d 2020-03-07 JaeyoungLim - Clear formatting and cleanups
639a6bb 2020-03-07 JaeyoungLim - Add parachute plugin
42d05bd 2020-03-09 RomanBapst - standard vtol: decrease rotorDragCoefficient to more realistic values
5669e5c 2020-03-07 leftytechie - Version check (#418)
82657d3 2020-03-07 Lorenz Meier - Fix geotagged images GPS position The GPS position was invalid, leading to incorrectly displayed geotag markers and to incorrect geotags in images.
8794a70 2020-03-02 Julian Oes - cmake: remove warning
7aba744 2020-02-26 TSC21 - gazebo_mavlink_interface: use class enum; use binary notation with the bitmask operations
0dc43a4 2020-02-26 TSC21 - gazebo_mavlink_interface: make sure to always send gyro and accel data in the HIL_SENSOR msgs
0c954a2 2020-02-25 TSC21 - mavlink_interface: split groundtruth stream from sensor stream; only apply rotations where needed
bc92d96 2020-02-25 TSC21 - set baro rate at 50Hz (averaging the PX4 baro drivers ODR)
94d16e6 2020-02-25 TSC21 - update magnetometer rate to 100Hz (fitting the ODR in most of the support PX4 mag drivers)
6cae120 2020-02-25 TSC21 - mavlink_interface: send HIL_SENSOR messages with the bitmask correctly defined IOT set each sensor stream rate separately
The problem with printing the exception was that starting with
Python 3.6 the ImportError is yet another (sub) exception called
ModuleNotFoundError which can't be printed as a string and then triggers
another exception:
```
Traceback (most recent call last):
File "/home/julianoes/src/Firmware/Tools/serial/generate_config.py", line 11, in <module>
import jinja2
ModuleNotFoundError: No module named 'jinja2'
During handling of the above exception, another exception occurred:
Traceback (most recent call last):
File "/home/julianoes/src/Firmware/Tools/serial/generate_config.py", line 13, in <module>
print("Failed to import jinja2: " + e)
TypeError: must be str, not ModuleNotFoundError
```
As per @bkueng's suggestion the easiest is to cast the exception to str
and that way prevent the second exception.
This allows us to print an error message instead of a weird Java failure
further down the road.
Better yet would be if this would take down everything, so a user does
not have to scroll up to read the message.
- sitl_gazebo in PX4/Firmware (635ceccfdb): a5b33417f7
- sitl_gazebo current upstream: 2f4b32723c
- Changes: a5b33417f7...2f4b32723c
2f4b327 2019-10-21 Martina Rivizzigno - typhoon sonar fix rotation such that the reported orientation metches the gazebo model
7db52d7 2019-10-18 Martina Rivizzigno - typhoon_h480: rotate sonar such that is forward facing
This should prevent debconf from asking questions during install.
Presumably, the exported env variable DEBIAN_FRONTEND is not taken into
account in a sudo command, hence we need to add it every time.
As far as I know these dependencies are only ever required when doing
analysis in ECL. At that point developers should be confident to add
what is required.
The bulk of this change was tightly coupled and needed to be deleted in one pass. Some of the smaller changes were things that broke as a result of the initial purge and subsequently fixed by further eradicating unnecessary platform differences. Finally, I deleted any dead code I came across in the related files I touched while going through everything.
- DriverFramework (src/lib/DriverFramework submodule) completely removed
- added dspal submodule in qurt platform (was brought in via DriverFramework)
- all df wrapper drivers removed
- all boards using df wrapper drivers updated to use in tree equivalents
- unused empty arch/board.h on posix and qurt removed
- unused IOCTLs removed (pub block, priv, etc)
- Integrator delete methods only used from df wrapper drivers
- commander: sensor calibration use "NuttX version" everywhere for now
- sensors: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- battery_status: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- cdev cleanup conflicting typedefs and names with actual OS (pollevent_t, etc)
- load_mon and top remove from linux boards (unused)
- delete unused PX4_MAIN_FUNCTION
- delete unused getreg32 macro
- delete unused SIOCDEVPRIVATE define
- named each platform tasks consistently
- posix list_devices and list_topics removed (list_files now shows all virtual files)
On Ubuntu we often saw the error
Assistive technology not found AWTError when starting jMAVSim.
This should be fixed by appending this cli argument to java.
As suggested in https://github.com/PX4/containers/issues/206
This target was never fully supported and is heavily dependent on a number of DriverFramework drivers that have no in tree equivalents (bebop bus, flow, rangefinder, etc). Deleting this will make it easier to fully drop DriverFramework shortly.
- make sure to kill all px4 instances and gazebo client when exiting
- add arguments to specify number of vehicles and vehicle model
- exit for now if vehicle model is not iris, since needs changes in
sitl_gazebo submodule
Signed-off-by: RomanBapst <bapstroman@gmail.com>
Main UAVCAN protocol handling and ESC updates run on the same thread/wq as
before. There are 2 WorkItems for separate scheduling of the 2, so that
ESC updates run in sync with actuator_control updates. UAVCAN is scheduled
at a fixed rate of 3ms (previously the poll timeout) and on each UAVCAN
bus event.
This leads to roughly the same behavior as before. CPU & RAM usage are
pretty much the same (tested on Pixhawk 4).
Testing done: Motors still work (with feedback), param changes and a
UAVCAN optical flow sensor.
The 9 seconds to erase a board probably still come from the FMU-v1 and
Pixhawks with only 1 MB flash. By now, many targets have 2 MB flash and
take a bit longer to erase. Therefore, we can increase the estimated
time a bit and don't need to resort to the timeout notice.
- jMAVSim in PX4/Firmware (a6a8877463): 3bd51e67e0
- jMAVSim current upstream: eeb23ef68e
- Changes: 3bd51e67e0...eeb23ef68e
eeb23ef 2019-10-30 bresch - magnetometer: update inclination/declination/local mag field strength of default starting locations. Set magnetometer scale factor to 1 (instead of 2) Set local mag field using DEFAULT_MAG_FIELD instead of an estimated one using inclination/declination and a norm of 1
* ubuntu.sh: fix space and capitalization
* Add setup script for Arch Linux
* arch.sh: remove numerous confirmations, added some base packages
* setup scripts: adjust messages according to review
* bump container tags to 2019-10-04
* docker_run: update container name and tag
* generate_microRTPS_bridge.py: force FastRTPSGen to version 1.0 if the result of 'fastrtpsgen -version' command is not a number
* CI: temporarly disable avoidance and safe landing tests
* CI: try to revive tiltrotor test
* adds a work_queue systemcmd that will bring a tree view of all active work queues and work items
* WorkQueues now track attached WorkItems and will shutdown when the last WorkItem is detached
* Add kdevelop to gitignore
* Add test stubs
* Rename px4_add_gtest to px4_add_unit_gtest
* Add infrastructure to run functional tests
* Add example tests with parameters and uorb messages
* Fix memory issues in destructors in uORB manager and CDev
* Add a more real-world test of the collision prevention
- sitl_gazebo in PX4/Firmware (7bba5a7287): 95adbb11f8
- sitl_gazebo current upstream: 22df9475ca
- Changes: 95adbb11f8...22df9475ca
22df947 2019-06-27 Martina Rivizzigno - Range.proto: fix indentation
8ef5625 2019-05-28 Martina Rivizzigno - update sonar message to match mavlink distance sensor definition
e04ff96 2018-12-04 Martina - get distance sensor orientation from the vehicle model instead of hard-coding it in the gazebo interface, add horizontal and vertical fov
In order to be consistent between Gazebo and jMAVSim we should be using
the env variable PX4_SIM_SPEED_FACTOR in the same way. This enables
vscode to set the speed using the env variable.
- sitl_gazebo in PX4/Firmware (b0176dc88a): a0b0eb8df1
- sitl_gazebo current upstream: af00ac4dfc
- Changes: a0b0eb8df1...af00ac4dfc
af00ac4 2019-06-07 Lukas Woodtli - Add support for unit tests on macOS
3a81838 2019-06-04 Lukas Woodtli - Add support to build and run unit tests with catkin
c59d214 2019-05-11 Lukas Woodtli - Add unit tests for gps plugin
860e1ce 2018-09-20 Lukas Woodtli - Add unit tests for gimbal controller plugin
Before, the pyserial check would fail before it could check for the
VERSION that the Python 2.7 version contains. This fixes it to check
for the VERSION independently.
- sitl_gazebo in PX4/Firmware (88127380e7): 3062d287c3
- sitl_gazebo current upstream: a0b0eb8df1
- Changes: 3062d287c3...a0b0eb8df1
- a0b0eb8 2019-05-10 bazooka joe - Calculate iris inertia from the body colision parameters assuming that the body is homogenic cube. that fixes impossible inertia matrix
- 113605b 2019-03-27 Elia Tarasov - fix gimbal_controller timestep sign
* VTOL trans: changed that now in transition for both MC and FW the corresponding (correct) attitude controller is running
* attitude setpoint for stabilized mode is generated by tailsitter.cpp
* reset yaw setpoint during transition to avoid big yaw errors after
transition back to hover
* VT_TYPE parameter: added "reboot required" metadata
- jMAVSim in PX4/Firmware (7ec6f0dca6): 79586deda5
- jMAVSim current upstream: ae1593d0c8
- Changes: 79586deda5...ae1593d0c8
ae1593d 2019-04-30 Julian Oes - Merge pull request #100 from PX4/fix-port-default
9de8f86 2019-04-29 Julian Oes - Simulator: fix default for QGC and SDK link
d42efaf 2019-04-29 Julian Oes - Merge pull request #99 from PX4/pr-add-sdk-port
7d0bebb 2019-04-26 Julian Oes - Simulator: fix copy paste mistake
a94816e 2019-04-26 Julian Oes - Simulator: add MAVLink UDP port for SDK
6a9634b 2019-04-26 Julian Oes - Visualizer3D: ran fix_style.sh
Includes:
- Fix for vibration on ground for standard_vtol.
- Noise for diff pressure / airspeed on Gazebo side.
- Fix for macOS magnetometer plugin linking error.
This is a workaround for the write timeout that we have seen for some
host computers trying to flash the firmware.
We don't know the root cause of the problem but we do observed the
following:
- For blocking writes with timeout (Pyserial write_timeout=0.5):
write() throws SerialTimeoutException. In systrace we see that the
select() call after write waiting for the write to be finished hangs
and finally times out.
- For blocking writes without timeout (Pyserial write_timeout=None):
write() hangs indefinitely. In systrace we see that the
select() call after write waiting for the write to be finished hangs.
- For non-blocking writes:
write() works but flush() hangs. In systrace we see that
ioctl(fd, TCSBRK, 1) which is (correctly) triggered by termios tcdrain
hangs.
Inspecting USB traffic using usbmon, we can see that the data which is
written actually seems to be sent and looking at responses from the
Pixhawk bootloader and the timings it looks like all the data has
arrived.
This workaround uses non-blocking writes without flushing and this
seemed to prevent the issue from happening so far.
Debugging was done in collaboration with Beat Küng and David Sidrane.
If we dont explicitly check for pyserial, we can have the case where the
import works but the Serial object creation fails. However, we don't see
this because we have this huge try/catch block which swallows
everything.
- sitl_gazebo in PX4/Firmware (4e792b2487): b34a96e7e5
- sitl_gazebo current upstream: 2e80474653
- Changes: b34a96e7e5...2e80474653
2e80474 2019-02-18 Elia Tarasov - fix comment for mag strength table unit
9a9a137 2019-02-18 Elia Tarasov - fix comment for the file name
7c49b2f 2019-02-18 Elia Tarasov - add units to mag variables
c004d94 2019-02-18 Elia Tarasov - fix magnetic field calculation by using geo lookup table
e9a3940 2019-02-18 Elia Tarasov - fix comment on magnetic data source and properties
c76ac17 2019-02-18 Elia Tarasov - copy magnetic data tables and functions from ecl/geo_lookup
28f59c5 2019-02-18 Elia Tarasov - add constrain function
8c869ed 2019-02-18 Elia Tarasov - fix linker complain on multiple definitions
b5213a7 2019-02-18 Elia Tarasov - add getters for mag inclination and strength
d311233 2019-02-15 Elia Tarasov - fix D-component of magnetic field for Zurich according to WMM2015
This updates the jMAVSim submodule which includes a fix for HITL.
In order to fix HITL, a CLI argument `-lockstep` was required to enable
lockstep. This has now been added to the command in jmavsim_run.sh.
* refactor ekf analysis part 1: move plotting to functions
* add plot_check_flags plot function
* put plots in seperate file
* use object-oriented programming for plotting
* move functions for post processing and pdf report creation to new files
* add in_air_detector and description as a csv file
* refactor metrics and checks into separate functions
* refactor metrics into seperate file, seperate plotting
* ecl-ekf tools: re-structure folder and move results table generation
* ecl-ekf-tool: fix imports and test_results_table
* ecl-ekf tools: bugfix output observer tracking error plot
* ecl-ekf-tools: update batch processing to new api, fix exception handling
* ecl-ekf-tools: use correct in_air_detector
* ecl-ekf-tools: rename csv file containing the bare test results table
* ecl-tools: refactor for improving readability
* ecl-ekf tools: small plotting bugfixes
* ecl-ekf tools: small bugfixes in_air time, on_ground_trans, filenames
* ecl-ekf-tools: fix amber metric bug
* ecl-ekf-tools: remove custom function in inairdetector
* ecl-ekf-tools: remove import of pandas
* ecl-ekf-tools: add python interpreter to the script start
* ecl-ekf-tools pdf_report: fix python interpreter line
* px4-dev-ros-kinetic: update container tag to 2019-02-13
* ecl-ekf-tools python interpreter line: call python3 bin directly
* ecl-ekf-tools: change airtime from namedtuple to class for python 3.5
* ecl-ekf-tools: update docker image px4-dev-ros-kinetic
* ecl-ekf-tools: fix memory leak by correctly closing matplotlib figures
- Jenkins compile drop arch until container is updated and maintained
- clang-tidy disable for now, the new version isn't respecting the existing configuration
* attitude and rate setpoint message: use 3D array for thrust demand
* FixedWingAttitudeControl: rework airspeed scaling
* move airspeed and scaling calculation into separate method
* if vtol in hover and airspeed disabled use minimum airspeed instead of trim airspeed
- sitl_gazebo in PX4/Firmware (560a9b45ed): 3d80f63562
- sitl_gazebo current upstream: 2adc86b5bf
- Changes: 3d80f63562...2adc86b5bf
2adc86b 2018-11-14 Elia Tarasov - add max value for wind and wind gust means
fb20a36 2018-11-14 Elia Tarasov - add normal gaussian distribution to wind gust force and direction
bd5ce12 2018-11-14 Elia Tarasov - add normal gaussian distribution to wind force and direction
913c094 2018-11-07 Jacob Schloss - reverse order of test
7d08ef5 2018-11-07 Jacob Schloss - fall back to only enabling up to c++14 on old cmake
0fd93b0 2018-11-07 Jacob Schloss - set CMAKE_CXX_STANDARD so cmake does not append a defualt language standard
The open flag `U` causes a deprecation warning starting with Python 3.4.
The option to open all kinds of newlines as `\n` has been replaced with
the argument `newline=None`. However, this argument is not available for
Python 2 unless we use `io.open` instead of `open`.
to fix Cygwin upload. It failed silently but when catching it prints
"non-standard baudrates are not supported on this platform".
Discussion about platform independet FTDI detection is in issue #10429.
This uses the systems default shell:
- Ubuntu: dash
- Fedora: bash
Since bash is invoked via /bin/sh, it operates in POSIX mode:
https://tiswww.case.edu/php/chet/bash/POSIX
- remove '# Ignore the expand_aliases command in zshell.'
Not needed because the shell operates in POSIX mode
- [[ is bashism -> use [
- autostart_files=( $autostart_file_match )
is not supported in dash, so use 'ls'
- shellcheck runs the dash flavor, since dash is a minimalistic shell.
Tested on dash & bash.
Jaeyoung-Lim
Mohamed Abdelkader Zahana
PX4 BuildBot
Daniel Agar
Lorenz Meier
Ramón Hernán Roche Quintana
Sander Swart
bbworld1
SalimTerryLi
Hamish Willee
Martin Povišer
Tomasz Domański
CUAVcaijie
David Sidrane
Jacob Dahl
James Goppert
Benjamin Perseghetti
Beat Küng
Nicolas MARTIN
Kabir Mohammed
Anton Erasmus
isidroas
Daniel Leonard Robinson
SungTae Moon
Julian Oes
Matthias Grob
Jan-Hendrik Ewers
JaeyoungLim
TSC21
Jonathan Hahn
David Jablonski
bresch
kritz
Jakub Kákona
baumanta
Hyon Lim
JacobCrabill
斯东Stone
Julian Kent
BazookaJoe1900
Ricardo Marques
Roman Dvořák
romain-chiap
RomanBapst
Christian Clauss
LP
CAI Dongcai
katzfey
Martina Rivizzigno
garfieldG
Hyon Lim
Julian Kent
Julien Lecoeur
Alexis Paques
Ildar Sadykov
Nico van Duijn
johannes
Anthony Lamping
Angel
David Sidrane
Mara Bos
Jake Dahl
CarlOlsson
sanderux
Pietro De Nicolao