Randy Mackay
f0ad8760e2
Rover: move rally to g2
2018-08-30 09:55:05 +09:00
Raouf
90fd64cf3a
Rover: add support for rally points
2018-08-30 09:54:51 +09:00
Thorsten Panitz
ee8d5d77d0
Rover: Activation of OSD
...
Rover: Activation of OSD
2018-08-30 08:19:02 +10:00
Randy Mackay
88a230e897
Rover: DPTH message only written if range finder last read time changed
2018-08-28 09:23:38 +09:00
Randy Mackay
19d943106b
Rover: pass vehicle speed to attitude control pitch control
2018-08-27 16:44:33 +09:00
Randy Mackay
5aa1286344
Rover: report left and right wheel control PID
2018-08-27 16:44:33 +09:00
Randy Mackay
e0fa829665
Rover: pitch PID_TUNING sends degrees
...
also send FF although it is rarely used
2018-08-27 16:44:33 +09:00
Randy Mackay
db611e074c
Rover: include wheel-rate-control
2018-08-27 16:44:33 +09:00
Randy Mackay
85ac24d96e
Rover: update wheel encoders at 50hz
2018-08-27 16:44:33 +09:00
Randy Mackay
69541fc89c
AP_MotorsUGV: use wheel-rate-control for skid steering vehicles
2018-08-27 16:44:33 +09:00
Randy Mackay
a5e28f0729
Rover: balancebot_pitch_control method removes unused armed arg
...
Also remove constraint on throttle output (this is handle in the AP_MotorsUGV library
Also move balance bot declarations to alphabetical order within Rover.h
2018-08-27 16:44:33 +09:00
Randy Mackay
961aab7425
Rover: balance bot passes motor limits to pitch control
2018-08-27 16:44:33 +09:00
Randy Mackay
9ae9f84498
Rover: fix G_Dt when SCHED_LOOP_RATE increased
...
This fixes a bug in the G_Dt calculation which is used in the motors library and PID controllers. The issue occurred in cases where the ahrs_update was not being run which could happen because it's estimated time was too long.
This also properly runs the critical functions (update ahrs, run flight mode code, send outputs to motors) at up to 400hz
2018-08-25 17:50:15 +10:00
Randy Mackay
473e8d18a1
Rover: reduce scheduler estimated time for gcs tasks
2018-08-24 15:30:50 +09:00
Pierre Kancir
3ef910ff11
Rover: fix initial target when setting Guided
2018-08-22 21:02:40 +09:00
Randy Mackay
8b9b1fdb66
Rover: set reverse to false on entering a mode
2018-08-22 14:25:30 +09:00
Randy Mackay
289fe6c391
Rover: minor fixes for reversed handling
2018-08-22 14:25:22 +09:00
Raouf
df3b6202f5
Rover: support DO_SET_REVERSE commands in guided, RTL, SmartRTL
2018-08-22 13:36:44 +09:00
Raouf
80753430e8
Rover: Accept DO_SET_REVERSE command
2018-08-22 13:36:41 +09:00
Raouf
ea62c24cef
Rover: Move set_reverse method to Mode class
2018-08-22 13:36:38 +09:00
Michael du Breuil
84baaea46d
Rover: Remove unneeded ServoRelayEvent mask set
2018-08-20 21:31:06 -07:00
Peter Barker
ca7842afac
Rover: add support for Sprayer
2018-08-17 15:33:35 +09:00
Randy Mackay
011776bff2
Rover: restore param description for CH7_OPTION
2018-08-12 14:00:48 +09:00
Randy Mackay
b5f045dc5f
Rover: mode description in lower case
...
Follow was in upper case
INITIAL_MODE was missing SmartRTL
2018-08-12 13:41:45 +09:00
Randy Mackay
c028aa8dad
Rover: fix compiler warning in RC_Channel
2018-08-11 11:23:35 +09:00
Ammarf
d665abccde
Rover: add output tests for omni frames
2018-08-08 17:07:50 +09:00
Raouf
f0185cb79b
Rover: Add loiter behaviour parameter
2018-08-08 07:17:13 +09:00
Ammarf
8308646c5e
Rover: change omniplus motor order
2018-08-08 07:15:37 +09:00
Ammarf
430ed9bd3d
Rover: add custom config support
2018-08-07 10:01:32 +09:00
Peter Barker
2365cdf90a
Rover: remove min-max-configured pre-arm checks
2018-08-07 09:45:09 +10:00
Randy Mackay
86634c2cca
Rover: log desired pitch in ATT message
2018-08-06 11:30:22 +09:00
Randy Mackay
0722c6a265
Rover: minor format fix to GCS_MAVLink.cpp
2018-08-06 11:30:22 +09:00
Randy Mackay
e71dc9307e
Rover: add Pitch to GCS_PID_MASK param description
2018-08-06 11:30:22 +09:00
Randy Mackay
e867ef74cc
Rover: balance bots log pitch PID
2018-08-06 11:30:22 +09:00
Randy Mackay
936dca7531
Rover: remove compass accumulate
2018-08-06 11:05:34 +10:00
Andrew Tridgell
73ccf90087
Rover: fixed RC_Channels parameter docs
2018-08-04 12:28:38 +10:00
Lucas De Marchi
00f03360bc
APMrover2: kill AP_FEATURE_SAFETY_BUTTON
...
This is redundant and can be just HAL_HAVE_SAFETY_SWITCH.
2018-08-02 13:15:02 -07:00
Peter Barker
5d923aed85
Rover: remove dead gcs failsafe code
...
Also use rc().has_valid_input() before using radio for trim
2018-08-02 15:21:03 +09:00
Peter Barker
e501ba203f
Rover: rename control_modes.cpp to RC_Channel.cpp
2018-08-02 09:52:29 +09:00
Randy Mackay
fada9f1990
Rover: version to 3.5.0-dev
2018-08-01 20:23:24 +09:00
Peter Barker
1f0908bba2
Rover: move handling of RC Switches into RC_Channel
...
Rover: use base-class auxsw handling
Rover: factor out do_aux_function_change_mode
Rover: move mode number enumeration to be in Mode:: namespace
Rover: move mode switch handling to RC_Channel
Rover: rename control_modes.cpp to RC_Channel.cpp
Rover: move motor_active() to be a method on the motors class
2018-08-01 12:11:30 +09:00
Michael du Breuil
f4d2014b56
Rover: Update notify initilization
2018-08-01 09:22:09 +10:00
Randy Mackay
315a33ed10
Rover: 3.4.2 release notes
2018-07-30 14:37:55 +09:00
murata
c705d3d816
Rover: Modify indentation (NFC)
2018-07-30 08:17:53 +09:00
Ebin
6dcab4e87b
Rover: support balance bot in AUTO mdoe
2018-07-28 08:44:18 +10:00
Randy Mackay
f7f4b43683
Rover: 3.4.2-rc1 release notes
2018-07-23 17:15:33 +09:00
Peter Barker
24ef1a61b3
Rover: remove old AP_Menu include
2018-07-23 14:20:22 +09:00
Randy Mackay
82aba6fe56
Rover: guided heading-and-speed control slows using yaw error
2018-07-18 15:11:09 +09:00
Randy Mackay
5dc4b8e66d
Rover: guided mode slows to stopping point on init
2018-07-18 15:11:09 +09:00
Randy Mackay
77598f72d1
Rover: remove redundant set_steering calls from Guided
...
steering is centered within the stop_vehicle method
2018-07-18 15:11:09 +09:00
Randy Mackay
3b7e84ce7a
Rover: calc_steering_to_heading updates yaw error
...
this allow the vehicle's speed to be reduced based on the heading error
2018-07-18 15:11:09 +09:00
Randy Mackay
84bda4e893
Rover: follow mode fixes and improvements
...
fix follow endless loop on enter
pass mavlink messages to AP_Follow
separate follow from guided
follow slows based on yaw error
check follow is enabled before entering follow mode
fix order in switch statement when converting from mode number to mode object
remove unused last_log_ms from follow mode
2018-07-18 15:11:09 +09:00
Ammarf
c0082271e6
Rover: implement Follow mode
2018-07-18 15:11:09 +09:00
Michael du Breuil
84f891c5b1
Rover: Remove unused ADC include
2018-07-17 09:29:50 +10:00
Andrew Tridgell
08da22c682
Rover: improved setup of output modes
2018-07-13 16:11:12 +09:00
Michael du Breuil
2b5aa9bc53
Rover: Remove usage of analogPinToDigitalPin
2018-07-11 23:09:52 -07:00
jeff567
200a644cfe
Rover: fixes bug in rovers with pivot turning
2018-07-11 11:35:43 +09:00
Peter Barker
b62639e07c
Rover: handle MAV_CMD_ACCELCAL_VEHICLE_POS in GCS base class
2018-07-06 09:43:09 +10:00
Peter Barker
0785e48718
Rover: handle command_int in base class
2018-07-06 09:43:09 +10:00
Peter Barker
1da3e8f182
Rover: handle command_long in GCS base class
2018-07-06 09:43:09 +10:00
Peter Barker
efdc13d143
Rover: remove pointless rangefinder_init shim function
2018-07-04 21:08:47 +01:00
Peter Barker
ca264b1932
Rover: use compass singleton for logging
2018-07-04 20:11:27 +01:00
Andrew Tridgell
8f94302348
Rover: removed unused macros
2018-07-04 20:05:10 +01:00
Ebin
07fc5c8349
Rover: removed min speed crash check for balance bot
2018-07-04 16:34:52 +09:00
Randy Mackay
eb58399d8b
Rover: 3.4.1 release notes
2018-07-04 11:37:52 +09:00
Peter Barker
b38b9dc07c
Rover: use ArmingMethod enumeration
2018-07-03 15:16:38 +10:00
Peter Barker
ea12f6caec
Rover: use singletons in AP_Arming
2018-07-03 13:44:11 +10:00
Peter Barker
e1408696dc
Rover: move mavlink reboot code up to base class
2018-07-03 12:12:25 +10:00
Randy Mackay
b9d8f53af2
Rover: correct object avoidance parameter descriptions
2018-06-29 14:56:33 +09:00
Ebin
96d4335765
Rover: Crash check based on angle for all rover frames
2018-06-28 21:55:20 +09:00
Ebin
04604ced33
Rover: BalanceBot.cpp renamed to balance_bot.cpp
2018-06-28 21:55:20 +09:00
Ebin
73e6ce18a0
Rover: Crash checks for Balance Bot
2018-06-28 21:55:20 +09:00
Ebin
2780d1715c
Rover: balance bot pitch control added in all modes
2018-06-28 21:55:20 +09:00
Ebin
c65405541e
Rover: balancing function call moved to manual mode update()
2018-06-28 21:55:20 +09:00
Ebin
6c2f18cc2f
Rover: manual mode support for balancebot
2018-06-28 21:55:20 +09:00
Ebin
936ebbe1f3
Rover: Added BalanceBot as a rover frame
2018-06-28 21:55:20 +09:00
Michael du Breuil
b5bc9e5147
Rover: Remove unneeded battery failsafe flag clearing
2018-06-27 11:39:35 +10:00
Raouf
9d51e87762
Rover: Save compass offsets when disarmed and learning is on
2018-06-26 08:51:16 +09:00
Peter Barker
3f0a56a818
Rover: use arming check_failed function
2018-06-23 15:33:19 +10:00
Andrew Tridgell
667ad98057
Rover: added ESC_TELEMETRY to mavlink streams
2018-06-21 10:48:02 +10:00
Peter Barker
87a3fcdd02
Rover: remove usb-mux checking
...
Nobody ever uses the result from this
2018-06-20 02:12:56 +01:00
Peter Barker
ab6cf171da
Rover: use AP_FWVersion singleton
2018-06-18 19:10:37 +01:00
Randy Mackay
03babfdc3c
Rover: fix RNGFND_TURN_ANGL param description again
2018-06-18 17:51:46 +09:00
Randy Mackay
9efa7ad635
Rover: fix RNGFND_TURN_ANGL range
2018-06-18 16:06:45 +09:00
Randy Mackay
acfbce95a6
Rover: update NTUN logging
...
reorder to allow easier comparing of adjacent fields
remove absolutes
rename fields
2018-06-18 10:25:56 +09:00
Peter Barker
9b269b1b56
Rover: use AP_RTC
...
Rover: AP_GPS now sets the system time directly
2018-06-15 08:01:22 +10:00
Randy Mackay
3ca520021b
Rover: version to 3.4.2-dev
2018-06-12 20:57:25 +09:00
Randy Mackay
a566ad48e9
Rover: 3.4.1-rc1 release notes
2018-06-12 20:56:50 +09:00
Randy Mackay
c650c52577
Rover: 3.4.0 release notes
2018-06-12 18:20:11 +09:00
Randy Mackay
f0780c7bb1
AP_MotorsUGV: minor comment fix
2018-06-12 17:44:10 +09:00
Randy Mackay
1c0d9c7512
AP_MotorsUGV: MOT_SPD_SCA_BASE param for min speed scaling
...
This replaces the hardcoded 1m/s start point for speed scaling with a configurable value
2018-06-12 17:44:10 +09:00
Randy Mackay
5faff519c3
AP_MotorsUGV: steering limits and constraint done by each output handler
...
each motor output handler (regular, skid, omni) becomes responsible for constraining the steering input (if required) and setting the limits flags
it is possible to reduce duplicate code but I think it might be more important to keep it clear which level is responsible for the limiting and constraining of steering
2018-06-12 17:44:10 +09:00
Michael du Breuil
c85f8c7bf5
Rover: Simplify radio trimming, improve MAVLink report
2018-06-11 16:29:36 -07:00
Randy Mackay
b69155793f
Rover: add Log_Write_Depth
2018-06-12 08:29:08 +09:00
Randy Mackay
d34c87a457
Rover: alphabetise Log_Write methods
2018-06-12 08:29:08 +09:00
Randy Mackay
c51b38cd1c
Rover: rename Log_Arm_Disarm to Log_Write_Arm_Disarm
2018-06-12 08:29:08 +09:00
Randy Mackay
10d89f1315
Rover: remove unimplemented Log_Write_Performance declaration
2018-06-12 08:29:08 +09:00
Randy Mackay
631d8f5423
Rover: accept do-change-speed commands with high speeds
2018-06-11 09:10:35 +09:00
Randy Mackay
a08a955cbc
Rover: accept DO_CHANGE_SPEED commands
2018-06-11 09:10:35 +09:00
Randy Mackay
8464e82812
Rover: set_desired_speed range checks speed
2018-06-11 09:10:35 +09:00
Randy Mackay
c8f4227313
Rover: remove SPEED_TURN_GAIN
...
Loiter was the only mode using this, replaced with hardcoded gain. The desired speed in Loiter also uses a hardcoded gain so this should work
2018-06-08 09:19:25 +09:00
Randy Mackay
645edf1f57
Rover: wp_overshoot used to limit speed in Auto
...
Limits desired speed to max possible given max lateral
acceleration and distance to line between waypoints
Replaces the use of SPEED_TURN_GAIN which scaled down speed
Also used in Guided, RTL, SmartRTL
2018-06-08 09:19:25 +09:00
Peter Barker
cf1f2f9aeb
Rover: move motors_active to be motors.active
...
This will help when we come to subclass the Motors library.
2018-06-08 08:51:18 +09:00
Peter Barker
65b7ca3fbb
Rover: factor out a do_aux_function_change_mode
...
Less code is good
2018-06-08 08:50:08 +09:00
Peter Barker
36705af8ff
Rover: create an enumeration to hold vehicle mode constants
...
This gives us type-safety on the mode numbers. This is advantageous as
some of these symbols exist with different values elsewhere in the code.
2018-06-08 08:41:16 +09:00
Michael du Breuil
cc772710ec
Rover: Rework to support override changes
2018-06-05 09:51:09 +10:00
Michael du Breuil
0ad2750f55
Rover: Remove software type param
2018-06-05 09:14:12 +10:00
Peter Barker
424d243c7f
Rover: move try_send_message handling of EKF_STATUS_REPORT up
2018-06-01 16:12:45 +01:00
Randy Mackay
c83ff0e156
Rover: 3.4.0-rc1 release notes
2018-06-01 16:40:54 +09:00
Randy Mackay
1e058045f7
Rover: guided mode more forgiving of set-position-targets type_mask field
...
accept position targets regardless of any other bit settings in type mask field. This makes rover more forgiving of errors in the type_mask field.
2018-06-01 15:05:48 +09:00
Ammarf
26c25daa36
Rover: add support for lateral control input
2018-05-31 13:48:17 +09:00
Randy Mackay
73bdc3be09
Rover: set ahrs flyforward if thr over 15% for 2 seconds
...
or if throttle is positive and desired speed over 0.5m/s
2018-05-29 16:37:31 +09:00
Peter Barker
12853f8912
Rover: correct compilation for transitive include fail
2018-05-29 14:42:02 +10:00
Peter Barker
c99cc465e6
Rover: split home-set and home-locked state
2018-05-29 14:38:45 +10:00
Peter Barker
829d18874e
Rover: create persist_streamrates() callback to indicate persistence
2018-05-29 13:08:29 +10:00
Peter Barker
9d83ee8cc7
Rover: move sending of vfr_hud up
2018-05-29 13:00:40 +10:00
Randy Mackay
70cef2f61e
Rover: report set-attitude-target capability
...
rover accepts the set-attitude-target mavlink messages
2018-05-25 10:40:49 +09:00
Ammarf
b95ac72d35
Rover: add LOITER to ch7 options
2018-05-24 17:59:45 +09:00
Randy Mackay
e1d80e547d
Rover: proximity sensor sets laser unhealthy when no data
...
previously it would set laser to unhealthy if proximity sensor wasn't present which interfered with a single downward facing range finder
2018-05-24 12:46:38 +09:00
Randy Mackay
60b9f6f9c0
Rover: report laser as healthy even if not used for avoidance
...
this allows downward facing lidar to be used on boats
2018-05-24 12:46:38 +09:00
Randy Mackay
51a0cbc1da
Rover: loiter slows using attitude control get_desired_speed_accel_limit
2018-05-24 11:06:20 +09:00
Randy Mackay
fc35e74821
Rover: pass dt to attitude controller
2018-05-24 11:06:20 +09:00
Randy Mackay
444e64a3d0
Rover: slow before pivot turns
2018-05-24 11:06:20 +09:00
Peter Barker
8101f2b573
Rover: move sending of simstate up
2018-05-23 18:36:50 +10:00
Randy Mackay
24dd9a1c2c
Rover: update GPS at 50hz
2018-05-23 17:17:29 +09:00
Randy Mackay
cc53b9c39d
Rover: update current_loc in update_ahrs
...
this ensures the current_loc is updated before any of the flight mode code runs
2018-05-23 17:17:29 +09:00
Ammarf
d7821635c0
Rover: seperate acceleration/deceleration limits
2018-05-23 17:17:29 +09:00
Peter Barker
e377debf25
Rover: add type-correctness for stream messages
2018-05-22 11:21:25 +10:00
Peter Barker
3f4783fa5d
Rover: move try_send_message of servo-output-raw up
2018-05-21 19:08:08 +01:00
Peter Barker
90124c20cb
Rover: shorten time remaining in try_send_message
...
The scheduler table entry for retrying defered messages doesn't allow
enough time for try_send_messages to run.
This change makes the time-remaining requirement the same as Plane.
2018-05-21 18:16:56 +09:00
Ammarf
2d64a47f90
Rover: add pivot_turn_rate to g2
2018-05-21 09:48:43 +09:00
Peter Barker
1ecd371cd0
Rover: move sending of GLOBAL_POSITION_INT up to GCS_MAVLINK
2018-05-17 15:48:06 +01:00
Peter Barker
0e8f01021d
Rover: remove arguments to send_home and send_ekf_origin
2018-05-17 20:42:36 +10:00
Peter Barker
3799a13bc3
Rover: move send_attitude up to GCS_MAVLINK
2018-05-17 18:28:43 +10:00
Peter Barker
c9d47c4ed5
Rover: move try_send_message sending of scaled_pressure up
2018-05-17 15:37:14 +10:00
Peter Barker
ace48d72b0
Rover: move try_send_message sending of sensor offsets up
2018-05-17 15:37:14 +10:00
Peter Barker
a37c8eae1f
Rover: move try_send_message of RAW_IMU up to GCS_MAVLINK
2018-05-17 15:37:14 +10:00
Peter Barker
0d3051e46a
Rover: handle setting of ekf origin in GCS_MAVLink
2018-05-17 10:13:42 +10:00
Peter Barker
a52f3d8f70
Rover: move Log_Write_Home_And_Origin into AP_AHRS
2018-05-17 10:13:42 +10:00
Michael du Breuil
dcb0a37643
Rover: AP_Proximity is now a common library
2018-05-16 23:21:41 +01:00
Michael du Breuil
dc5fae9ea6
Rover: Support rangefinder MAVLink changes
2018-05-16 23:21:41 +01:00
Randy Mackay
fb4dcc2458
Rover: 3.3.1-rc2 release notes
2018-05-12 17:57:09 +09:00
Peter Barker
3afe591368
Rover: correct compilation when logging is disabled
2018-05-10 17:55:13 +09:00
Randy Mackay
3d1c078a44
Rover: steering mode uses turn rate control when stopped
2018-05-10 08:02:13 +09:00
Randy Mackay
0a29e4eac5
Rover: fix calc-steering-to-waypoint go use real heading without reverse
2018-05-10 08:02:13 +09:00
Randy Mackay
3645e18243
Rover: acro and steering use get_pilot_desired_steering_and_speed
2018-05-10 08:02:13 +09:00
Randy Mackay
957458ca56
Rover: add get_pilot_desired_steering_and_speed
...
Also fix reversed steering response where throttle or acceleration limiting leads to throttle output being in the opposite direction from pilot's throttle input
2018-05-10 08:02:13 +09:00
Randy Mackay
ef2223a712
Rover: integrate attitude control change to steering output and scaling
...
steering output is always positive for clockwise
steering is scaled in motors library meaning we do not need to tell attitude controller about skid-steering or vectored-thrust
2018-05-10 08:02:13 +09:00
Randy Mackay
0830e057e0
Rover: manual mode outputs unscaled steering
2018-05-10 08:02:13 +09:00
Randy Mackay
6b6c0f04b6
Rover: get_pilot_desired_steering_and_throttle returns steering assuming positive is always clockwise
2018-05-10 08:02:13 +09:00
Randy Mackay
a061203eaf
Rover: pass ground speed to motors lib for scaling of steering
2018-05-10 08:02:13 +09:00
Randy Mackay
d018a9334e
AP_MotorsUGV: add get_slew_limited_throttle
...
required by vehicle code to properly handle steering direction in cases where the driver's input throttle has the opposite sign from output throttle because throttle is being slew limited
2018-05-10 08:02:13 +09:00
Randy Mackay
3db2cc700e
AP_MotorsUGV: positive steering always rotates vehicle right
...
also scale steering down with increased speed for regular rovers
add support for disabling scaling of steering
2018-05-10 08:02:13 +09:00
Randy Mackay
8137001a86
AP_MotorsUGV: minor comment fix
2018-05-10 08:02:13 +09:00
Peter Barker
b38d23d542
Rover: move sending of battery data up
2018-05-09 11:40:31 -07:00
Peter Barker
a692acad81
Rover: move data stream send up
2018-05-09 16:15:38 +10:00
Peter Barker
a78fe0896f
Rover: make scheduler track whether it has called the delay callback
2018-05-09 16:15:38 +10:00
Randy Mackay
468fc26e31
Rover: version to 3.4.0-dev
2018-05-09 13:32:50 +09:00
Randy Mackay
ef23672a76
Rover: 3.3.1-rc1 release notes fix
...
the pivot turn change was removed just prior to release
2018-05-09 13:11:29 +09:00
Randy Mackay
3860141da8
Rover: 3.3.1-rc1 release notes
2018-05-09 12:55:08 +09:00
Ammarf
de4e74b910
Rover: added comments to output_omni
2018-05-09 12:50:45 +09:00
Ammarf
aca2c596b4
Rover: Use output_throttle for omni rover motor output
2018-05-09 12:50:45 +09:00
Ammarf
d7e01d83d6
Rover: added is_omni_rover function
2018-05-09 12:50:45 +09:00
Randy Mackay
40a8e0de09
Rover: default BRD_SAFETYOPTION to to allow disarming with safety switch
2018-05-09 08:02:21 +10:00
Peter Barker
121cfc5b4c
Rover: AP_RSSI is included for all vehicles
2018-05-08 12:33:32 +01:00
Peter Barker
9e1811027d
APMrover2: move try_send_message handling of RC_CHANNELS_RAW up
2018-05-08 12:33:32 +01:00
Peter Barker
1bc208584f
Rover: move try_send_message of heartbeats up to GCS_MAVLINK
2018-05-07 11:30:13 -06:00
Peter Barker
25c2efb3ae
Rover: move try_send_message handling of VIBRATION up
2018-05-07 11:23:28 -06:00
Randy Mackay
8108931ee0
Rover: 3.3.0 release notes
2018-05-07 17:35:50 +09:00
Andrew Tridgell
a575608110
Rover: fixed build warnings
2018-05-07 11:43:23 +10:00
Randy Mackay
c6638f66de
Rover: Loiter mode for boats
2018-05-06 16:58:00 +09:00
Randy Mackay
341d75e0c9
AP_MotorsUGV: force throttle to zero when disarmed
2018-05-06 16:58:00 +09:00
Randy Mackay
c69f7bb1d0
AP_MotorsUGV: consolidate parameter sanity checks
2018-05-06 16:58:00 +09:00
Randy Mackay
c4804e4576
Rover: remove redundant avoidance call from steering
2018-05-06 16:58:00 +09:00
Peter Barker
0b1091231c
Rover: remove rcmap member from AP_AdvancedFailsafe
...
Also correct constructor for barometer
Also make it compile again
2018-05-05 18:06:31 +09:00
Randy Mackay
feb9cfc390
Rover: reduce TURN_MAX_G default to 0.6
2018-04-26 14:17:04 +09:00
Andrew Tridgell
c941d72ad1
Rover: remove old pde file
...
this was here for upgrading very old MissionPlanner versions. We can
remove it now
2018-04-26 14:25:01 +10:00
Michael du Breuil
da9053655b
Rover: Support new RC_Channels::read_input()
2018-04-26 08:00:09 +10:00
Randy Mackay
8119c537c7
Rover: integrate vectored thrust support
2018-04-24 19:57:19 +09:00
Randy Mackay
38b79cf0bc
AP_MotorsUGV: support vectored thrust
...
steering scaled down as throttle increases
2018-04-24 19:57:19 +09:00
Randy Mackay
29e8866ea9
Rover: move avoidance into calc_throttle
...
also enable avoidance for steering and guided modes
2018-04-24 12:24:53 +09:00
night-ghost
2aee8d1018
APMrover2: devo telemetry support (RX705/707)
2018-04-24 10:44:28 +10:00
Randy Mackay
8fa1700d02
Rover: 3.3.0-rc1 release notes
2018-04-19 17:20:38 +09:00
Randy Mackay
87eef9051f
Rover: increase default pivot turn angle to 60deg
...
pivoting at only 30degrees of error could lead to endless twitching back and forth for poorly tuned rovers
2018-04-19 16:32:48 +09:00
Peter Barker
d66cb1dda0
Rover: use AP_ServoRelayEvents singleton
2018-04-18 20:31:55 +09:00
Peter Barker
e73a02343a
Rover: GPS now logs its own data
2018-04-18 13:50:55 +09:00
Daniel Widmann
572d9ba43b
Rover: Allow switching to ACRO mode for skid steer rovers without GPS
2018-04-13 09:12:03 +09:00
Daniel Widmann
e782ce2b51
Rover: Allow ACRO mode for skid steer rovers without GPS
2018-04-13 09:12:03 +09:00
Peter Barker
63e8fffbe4
Rover: Baro does its own dataflash logging now
2018-04-12 19:12:12 +01:00
Michael du Breuil
05173f24c6
Rover: Use RC_Channels instead of hal.rcin
2018-04-11 21:47:07 +01:00
Michael du Breuil
3bad3b2e68
Rover: Check MANUAL_CONTROL target
2018-04-10 16:54:34 +01:00
Randy Mackay
da619e8aa6
Rover: 3.2.3 release notes
2018-04-09 09:04:30 +09:00
Andrew Tridgell
4f6240ee8a
Rover: handle oneshot125 separately
2018-04-07 09:10:29 +10:00
Andrew Tridgell
4350cee7cf
Rover: added mask to set_output_mode()
2018-04-07 09:10:29 +10:00
Randy Mackay
f7a168478d
Rover: integrate attitude control's get_steering_out_heading
2018-04-05 12:14:59 +09:00
Randy Mackay
e8070a5cb3
Rover: pass waypoint radius to L1 as min dist along track
2018-04-05 12:14:59 +09:00
Randy Mackay
41bd79a387
Rover: pivot-turn uses heading controller
2018-04-05 12:14:59 +09:00
Peter Barker
e74d07ff15
Rover: remove wrapper for Log_Write_Beacon
2018-04-04 16:20:33 +09:00
Francisco Ferreira
b2af1f1e05
Rover: fix method shadowing
2018-04-03 16:29:33 +01:00
Peter Barker
a45e3cba15
Rover: factor vehicle's mavlink send_heartbeat
2018-04-03 13:05:19 +01:00
Randy Mackay
c05d239069
Rover: remove throttle scaling dependency on throttle range
2018-04-03 10:42:39 +09:00
Randy Mackay
fa20fd695f
Rover: use throttle_min param as output deadzone
2018-04-03 10:42:39 +09:00
Randy Mackay
b9e32d1f44
Rover: reduce expected times in scheduler table
2018-04-03 08:40:31 +09:00
Peter Barker
c10f404b12
Rover: tidy handling of barometer calibrations
2018-04-02 23:25:05 +01:00
Peter Barker
b407a4eed8
Rover: move common calibration functions up
2018-04-02 23:25:05 +01:00
Peter Barker
762b31b147
Rover: create a preflight calibration function
...
Some functionality has moved up.
2018-04-02 23:25:05 +01:00
Peter Barker
db7ce9aba2
Rover: use ahrs singleton for SmartRTL
2018-04-02 17:16:02 +01:00
Randy Mackay
39bade1f4a
Rover: 3.2.3-rc2 release notes
2018-04-02 12:01:45 +09:00
Randy Mackay
c923158cc9
Rover: 3.2.3-rc1 release notes
2018-04-02 11:11:13 +09:00
nicknunno
8888adbfd4
Rover: TURN_MAX_G param desc update for range and increment
2018-04-02 09:13:25 +09:00
Michael du Breuil
b761a57da3
Rover: Support new battery interface
2018-03-27 22:12:21 +01:00
Peter Barker
57ed822db0
Rover: allow DataFlash to handle log sending
2018-03-26 09:22:47 +09:00
Peter Barker
3c58eca0ab
Rover: move handling of visual odometry messages up
2018-03-23 09:28:07 +09:00
Randy Mackay
96ae9cef14
Rover: send correct mav-type for boats
2018-03-22 09:11:52 +09:00
Randy Mackay
489551c9a4
Rover: 3.2.2 release notes
2018-03-19 19:11:53 +09:00
Peter Barker
bb7bed0614
Rover: move handling of get_home_position up
2018-03-19 10:32:37 +09:00
Peter Barker
7fd859da65
Plane: move home state into AP_AHRS
2018-03-19 10:32:37 +09:00
Peter Barker
9d0da4a71f
Rover: move home state into AP_AHRS
2018-03-19 10:32:37 +09:00
Peter Barker
ceb64fb7d9
Rover: use ins singleton
2018-03-16 00:37:35 -07:00
Randy Mackay
30ba463f42
Rover: minor comment fix to acro
...
non-functional change
2018-03-15 09:58:24 +09:00
Randy Mackay
00353c7a06
Rover: avoid divide by zero in desired speed at waypoint calcs
2018-03-14 12:40:04 +09:00
Randy Mackay
86c39c0314
Rover: run update_mission at 50hz
2018-03-14 12:40:04 +09:00
Randy Mackay
343d119726
Rover: wp nav uses stopping point or prev wp for origin
2018-03-14 12:40:04 +09:00
Randy Mackay
073d9519ca
Rover: version to ArduRover V3.3.0-dev
2018-03-12 16:11:37 +09:00
Randy Mackay
e3f70119fe
Rover: fix two-paddle input decoding
...
steering output was twice what it should be. full steering (i.e. 4500 or -4500) should occur when one paddle is up and the other is completely down
2018-03-12 14:39:13 +09:00
Peter Barker
81ba037582
Rover: use baro singleton
2018-03-08 21:20:05 -08:00
Peter Barker
1f772c05f4
Rover: delete correct assignment operator
2018-03-08 21:20:05 -08:00
Randy Mackay
dcfe104163
Rover: reduce CRUISE_SPEED default to 2m/s
...
based on user logs most rovers max speed is less than 4m/s so this default is closer to the average
2018-03-09 13:19:21 +09:00
Randy Mackay
1baa6eb049
Rover: 3.2.2-rc1 release notes
2018-03-08 16:24:03 +09:00
Randy Mackay
4e8399ca3f
Rover: acro and steering steer even with target speed of zero
2018-03-08 14:45:43 +09:00
Peter Barker
78ecf55fec
Rover: use AP::ahrs() for GCS_MAVLink
2018-03-07 12:34:39 +00:00
night-ghost
bab54ea647
Rover: allow AP_Stats to be optional
2018-03-02 07:23:35 +11:00
Andrew Tridgell
f190ca0867
Rover: use scheduler.get_last_loop_time_s()
2018-02-13 17:15:05 +11:00
Peter Barker
90d26a5100
Rover: eliminate perf_update scheduler table shim
2018-02-13 17:15:05 +11:00
Andrew Tridgell
80c45a7431
Rover: use filtered loop time
2018-02-13 17:15:05 +11:00
Peter Barker
7b6bc4adf1
Rover: pass log-performance-bit at init time rather than update time
2018-02-13 17:15:05 +11:00
Peter Barker
55c27dfc56
Rover: move logging of PM messages to AP_Scheduler
2018-02-13 17:15:05 +11:00
Peter Barker
b2e2b91d7e
Rover: move PERF: statustext sending into AP_Scheduler
2018-02-13 17:15:05 +11:00
Peter Barker
d9bb546048
Rover: use AP_Scheduler's loop() function
2018-02-13 17:15:05 +11:00
Peter Barker
211e7416a9
Rover: use scheduler ticks in place of mainloop_count
2018-02-13 17:15:05 +11:00
Peter Barker
9511e72113
Rover: use PerfInfo for performance monitoring
2018-02-13 17:15:05 +11:00
Randy Mackay
24b8ed48b6
Rover: global-pos-int uses vel from EKF instead of GPS
2018-02-13 08:52:48 +09:00
Randy Mackay
f47e65822f
Rover: fix global-pos-int velocity direction to NED
2018-02-13 08:52:48 +09:00
Peter Barker
df304c5e6b
Rover: remove shims used in scheduler table
2018-02-12 15:39:26 +09:00
Peter Barker
89c830e949
Rover: make SmartRTL mode decide whether to save position or not
...
This changes things to work like the Copter equivalent
2018-02-12 15:39:26 +09:00
Andrew Tridgell
65308f9411
Rover: removed compass learn_offsets()
2018-02-08 17:36:33 +11:00
Randy Mackay
0da8ff6b2e
Rover: boats always navigate when outside waypoint radius
2018-02-07 07:33:11 +09:00
Michael du Breuil
2e9e91b3a3
Rover: Move battery logging to AP_BattMonitor
2018-02-06 00:11:32 +00:00
murata
e94bfc7ee0
Rover: delete \n from the log using gcs().send_text
2018-02-02 09:38:36 +09:00
Randy Mackay
0626d105ed
Rover: version 3.2.1-dev fix
2018-01-29 19:37:46 +09:00