Randy Mackay
e5535e35b3
Copter: remove unused reset_stability_I
2013-09-24 21:42:05 +09:00
Randy Mackay
c596b27719
Copter: add dataflash error for GPS glitch
2013-09-24 21:41:48 +09:00
Randy Mackay
4c8227c050
Copter: update AP_Notify for gps failsafe and glitching
2013-09-24 21:41:28 +09:00
Randy Mackay
2f5b32bada
Copter: integrate GPS_Glitch's check_position
2013-09-24 21:41:16 +09:00
Andrew Tridgell
3378c7901a
Copter: added support for the flymaple board
2013-09-24 13:51:28 +10:00
Andrew Tridgell
754bdbd25f
Copter: use new usb_connected() HAL function
2013-09-19 16:24:23 +10:00
Randy Mackay
79399e4fb4
Copter: AC3.1-rc2 version and release notes
2013-09-18 13:30:26 +09:00
Randy Mackay
daa0cb7914
Copter: enable motor slow start in auto mode
2013-09-13 14:32:19 +09:00
Andrew Tridgell
3720efc7c9
Copter: changed to AP_Vehicle.h
2013-09-13 11:47:03 +10:00
Randy Mackay
43c4ba304d
Copter: update Release Notes for AC3.1-rc1
2013-09-09 20:04:30 +09:00
Randy Mackay
1abb439051
Copter: move acro's var initialisation to roll-pitch and yaw controller initialisation
2013-09-09 10:54:13 +09:00
Randy Mackay
942ba0476b
Copter: remove manual_attitude and throttle flags
2013-09-09 10:44:53 +09:00
Randy Mackay
4842335a24
Copter: add #include for AC_Sprayer
2013-09-09 10:18:06 +09:00
Andrew Tridgell
52f5b1e5a7
Copter: update to GPLv3 license headers
2013-08-30 13:01:39 +10:00
Andrew Tridgell
e1e32fcf08
Copter: fixed build with AP_AHRS changes
2013-08-30 13:01:35 +10:00
Andrew Tridgell
25d517f5d6
Copter: updates for new notify API
2013-08-30 13:01:35 +10:00
Randy Mackay
4aef49a006
Copter: re-order #defines of AP_Notify
2013-08-30 13:01:35 +10:00
Randy Mackay
52ef77393c
Copter: integrate Toshiba_LED_PX4
2013-08-30 13:01:35 +10:00
Randy Mackay
46c24fdf39
Copter: integrate ToshibaLED
2013-08-30 13:01:35 +10:00
Randy Mackay
e985253f1a
Copter: integrate notify
2013-08-30 13:01:35 +10:00
Randy Mackay
45aeb1a921
Copter: split up loiter into 4 steps
...
Reduces disruption to the main loop but also introduces a delay of 30ms
to navigation output
2013-08-28 11:33:10 +09:00
Randy Mackay
2696e160e6
Copter: surface tracking improvement
...
Separate correction speeds for pilot input vs altitude-above-ground
errors to allow slower correction to sonar signals.
Change SONAR_GAIN parameter to be altitude error -> desired speed. This
means it should be set 10x larger than before.
Replace hard-coded sonar cut-off percentage of 70% with
SONAR_RELIABLE_DISTANCE_PCT.
Reduce sonar cut-off percentage to 60%.
Add desired sonar altitude to dataflash log's CTUN message.
2013-08-19 09:52:59 +09:00
Randy Mackay
88332b4acb
Copter: revert to 3 element sonar's mode filter
2013-08-19 09:47:48 +09:00
Randy Mackay
3a5a15a15f
Copter: allow CH6 tuning of sonar gain
2013-08-18 15:44:54 +09:00
Randy Mackay
6a2daf1a33
Copter: reduce sonar sensitivity to spikes
2013-08-15 16:04:17 +09:00
Randy Mackay
6969ab573d
Copter: configurable max lean angle
...
ANGLE_MAX parameter allows limiting the roll and pitch angles during
manual and auto flight modes to anywhere from 10 to 80 degrees
2013-08-11 12:53:22 +09:00
Randy Mackay
74fb500efe
Copter: integrate AC_Sprayer
2013-08-05 21:12:23 +09:00
Randy Mackay
49dbdce89c
Copter: split ACRO_P into ACRO_RP_P and ACRO_YAW_P
2013-08-05 21:05:00 +09:00
Randy Mackay
82082e044c
Copter: remove ACRO's axis enabled parameter
...
Acro is now body frame (with earth frame leveling) while Sport is earth
frame acro
2013-08-05 21:04:57 +09:00
Randy Mackay
e32342163d
Copter: rename ACRO variables
2013-08-05 21:04:50 +09:00
Leonard Hall
d2deaaa686
Copter: Acro add rate constrain and combine limit calc
2013-08-05 21:04:47 +09:00
Randy Mackay
39ab4f62ef
Copter: add SPORT mode
2013-08-05 21:04:41 +09:00
Randy Mackay
a18d55a9d3
Copter: update version to 3.1-dev
2013-08-05 14:26:52 +09:00
Andrew Tridgell
2690edfc5f
Copter: ask for IMU samples at 100Hz
...
this produces the same result, but makes things simpler in the driver
2013-08-02 21:37:15 +10:00
Andrew Tridgell
01e19a32fe
Copter: use the new scheduler load_average() call
...
this also simplifies the main loop
2013-08-02 18:46:34 +10:00
Randy Mackay
0f8f5bc048
Copter: remove unused ap.gps_status flag
2013-07-29 16:46:05 +09:00
Olivier-ADLER
87d062905e
Copter: 3 positions switch support for CH7 and CH8 - new 3 positions SIMPLE / SUPERSIMPLE mode
...
3 positions modes must use mode number >= 100
pre-arm check correction for CH7 - CH8 check
2013-07-29 15:12:10 +09:00
Randy Mackay
3b59cde1b8
Copter: deactivate accel throttle controller when landed
2013-07-28 18:19:01 +09:00
Randy Mackay
da37089dc2
Copter: remove landing checks in loiter controller
2013-07-28 18:18:57 +09:00
Randy Mackay
8eefbdce44
Copter: turn off stability patch when landed in Loiter
2013-07-28 18:18:54 +09:00
Randy Mackay
9a1a999fba
Copter: landing check changes
2013-07-28 18:18:50 +09:00
Randy Mackay
24d15517ff
Copter: clear thr accel I term on take-off
2013-07-28 18:18:45 +09:00
Randy Mackay
05248738e2
Copter: bug fix for take-off in loiter
2013-07-28 18:18:43 +09:00
Randy Mackay
c3daf78340
Copter: reset loiter target when landed
2013-07-28 18:18:41 +09:00
Robert Lefebvre
2a9f4bbbad
TradHeli: Creating new unified roll/pitch rate controller.
2013-07-19 16:16:12 +09:00
Robert Lefebvre
23ea151ca5
TradHeli: Fix Heli rate controller filter rates.
2013-07-19 16:16:10 +09:00
Robert Lefebvre
b4863dc997
TradHeli: Change to throttle controller to allow swash plate collective to move, even if disarmed, if we are in Acro or Stab. This is slightly dangerous... as a user could cause a problem if they do not follow the proper usage procedures. If they do not route the ESC through the APM, but instead direct to Rx. And then if they do not Arm, they could take off in Stab mode while disarmed, but then when they switch to Alt_Hold, it will drop the collective to the bottom and they will fall. This can be saved by switching back to Stab. And it requires operation outside of the normal operating procedure.
...
This change is being made because most heli users expect to be able to check the swash plate operation before arming and taking off.
2013-07-19 16:16:04 +09:00
Andrew Tridgell
9a159a5e23
Copter: make wp_distance static
...
removed hack with AP_Camera library
2013-07-15 09:56:45 +10:00
Leonard Hall
64ce9b017d
Copter: Body frame ACRO upgrade
2013-07-11 17:53:25 +09:00
Randy Mackay
6dd446ac79
Copter: firmware version to 3.0.1
2013-07-11 16:45:05 +09:00
Andrew Tridgell
5ae62f4f04
Copter: fixed build with specified GPS driver
2013-07-11 14:27:42 +10:00
Randy Mackay
8cb7bd628e
Copter: change firmware version to 3.0.1-rc2
2013-07-10 15:52:21 +09:00
Andrew Tridgell
da4137b731
Copter: changes for GPS field changes
2013-07-10 14:04:22 +10:00
Craig@3DR
bbd4fbd2fb
Copter: trigger + logging on camera update_location()
2013-07-10 08:39:59 +10:00
Randy Mackay
79d2fe6271
Copter: double flash arming light when pre-arm checks fail
...
Hardly my finest work but it's temporary because we're going to replace
all the led, buzzer etc with a library called AP_Notify in the near
future.
2013-07-04 16:26:22 -10:00
Randy Mackay
404cd5f3da
Copter: rename g.pid_throttle to g.pid_throttle_rate
...
Small code clean-up to make throttle rate controller's pid more obvious
2013-06-30 00:04:21 -10:00
Randy Mackay
b3da8a462f
Copter: CH6 tuning definition clean-up
...
Renamed and reorganised the CH6 #defines and parameter definitions
2013-06-29 23:51:43 -10:00
Randy Mackay
0592475959
Copter: change firmware version to 3.0.0-rc1
2013-06-26 14:03:28 +09:00
Randy Mackay
45dfbecaba
Copter: update 3.0.1 version and release notes
2013-06-26 00:09:36 +09:00
Andrew Tridgell
3e82f644ea
Copter: enabled CAM_TRIGG_DIST parameter
2013-06-25 12:52:44 +10:00
Randy Mackay
245bc3d3fd
Copter: show pilot input in dataflash ATT message even when in AUTO
...
AUTO mode ignores pilot input but we still want to be able to see the
pilot's input in the Roll-In and Pitch-In columns of the dataflash's ATT
message
2013-06-19 12:37:13 +09:00
Randy Mackay
b1a014e12e
Copter: update firmware version to 3.0.0
2013-06-18 10:03:40 +09:00
Randy Mackay
b1e089fe29
Copter: update AC3.0-rc6 version and release notes
2013-06-16 11:48:03 +09:00
Randy Mackay
dd92a2ba07
Copter: AC3.0-rc5 version and release notes
2013-06-04 15:25:56 +09:00
Andrew Tridgell
ba959fd594
Copter: remove unused define
2013-06-04 10:36:34 +10:00
Andrew Tridgell
595d3c694a
Copter: make it possible to change board orientation at runtime
2013-06-03 16:52:52 +10:00
Randy Mackay
213eaa8db6
Copter: integrate draft RCMapper
2013-06-03 16:23:47 +10:00
Randy Mackay
9e91def774
Copter: update firmware version and release notes
2013-06-02 12:19:36 +09:00
Dr Gareth Owen
4c6d6ea96e
changed yaw reset to when armed to not use initial_simple_bearing
2013-06-02 11:29:30 +09:00
Randy Mackay
99f5462a03
Copter: circle mode fixes
2013-06-01 18:21:30 +09:00
Randy Mackay
1722e438d8
Copter: pass alt hold gain to WP_Nav library
2013-05-31 21:04:10 +09:00
Randy Mackay
838fb3f4e2
Copter: don't spin motors in ALTHOLD with zero throttle
2013-05-27 10:42:22 +09:00
Dr Gareth Owen
1aca66460e
7 yaw when armed option changed so overridable by user
2013-05-24 11:14:06 +09:00
Randy Mackay
22e9b95c3c
Copter: version update to 3.0.0-rc3
2013-05-22 17:46:28 +09:00
Randy Mackay
00bd1bf8ea
Copter: RESETTOARMEDYAW order and comments
...
We should keep the order in the case statement the same as the #define
order.
2013-05-21 10:58:34 +09:00
Dr Gareth Owen
f646b79e5f
indent correct again
2013-05-21 10:40:36 +09:00
Dr Gareth Owen
d9fc37c01c
indent correct
2013-05-21 10:40:34 +09:00
Dr Gareth Owen
e9d640ced8
added ch7 option to reset yaw back to what it was when quad was armed
2013-05-21 10:40:30 +09:00
Randy Mackay
6efdabb104
Copter: move auto disarm into a separate function
2013-05-20 14:05:50 +09:00
Randy Mackay
1dbe98b566
Copter: display reason for pre-arm-check failures in GCS
2013-05-20 13:03:18 +09:00
Randy Mackay
55f1b3b2ae
Copter: reorganise medium loop
...
Shifted compass logging to happen when compass is read.
Updated comments.
2013-05-20 11:18:51 +09:00
Randy Mackay
c840e2a8c2
Copter: code clean-up move 10hz loop after 50hz loop
2013-05-20 11:05:14 +09:00
Randy Mackay
38239c652a
Copter: ch8 aux switch
...
Ch8 can be used as an aux switch like ch7. Has all the same options as
ch7 and there is a safety check to ensure both switches aren't set to
the same function so as to avoid interfering with each other
2013-05-17 14:42:28 +09:00
Randy Mackay
19394918dd
Copter: simplify APM_Config.h
...
Remove items that can be more easily set with parameters
2013-05-17 12:01:39 +09:00
Randy Mackay
9d0f40b432
Copter: add pre_arm_rc_check
...
Motors are not be enabled unless we have passed rc checks which include
checking the radio in calibration has been performed.
2013-05-16 16:32:00 +09:00
Randy Mackay
33d1129904
Copter: remove unused TB_RATIO parameter
2013-05-14 16:56:55 +09:00
Randy Mackay
319f3ef560
Copter: flexible CH6 declination tuning range
2013-05-13 23:37:30 +09:00
Randy Mackay
6ba9431be4
Copter: update firmware version and release notes ahead of -rc2
2013-05-13 22:16:25 +09:00
Andrew Tridgell
c44fd42349
Copter: fixed RSSI reading on PX4
...
needed for different analog input scaling
2013-05-13 15:19:05 +10:00
Randy Mackay
ad656c7e8a
Copter: allow lat/lon to be specified for land
2013-05-10 22:37:15 +09:00
Randy Mackay
b65d714675
Copter: set yaw-mode in do_loiter mission command
2013-05-10 10:51:46 +09:00
Randy Mackay
ed5ddfd9db
WPNav: initialise desired roll, pitch
...
bug-fix to resolve 1/10th second twitch when loiter or waypoint
controller are first engaged
2013-05-09 18:32:02 +09:00
Randy Mackay
0a148cce19
Copter: log target alt in meters
2013-05-08 16:41:16 +09:00
Randy Mackay
ae2ad8e819
Copter: remove unused radius_of_earth constant
2013-05-05 13:13:48 +09:00
Randy Mackay
647a93e78e
Copter: remove jerk when entering RTL or AUTO
...
Loiter target position was not being initialised properly.
Add a few more comments
2013-05-03 16:58:00 +09:00
Randy Mackay
cca05ee8ae
Copter: start dataflash logging when arming
...
Stop nearly empty logs from being produced.
Removed redundant armed bit from ap state.
2013-05-03 14:49:55 +09:00
Andrew Tridgell
55da049c69
Copter: fixes for AP_Baro_HIL
2013-05-02 15:09:16 +10:00
Andrew Tridgell
25c576cad7
Copter: replaced constrain() with constrain_float()
2013-05-02 10:26:49 +10:00
Randy Mackay
d9601916ee
Copter: update firmware version and release notes for 3.0.0-rc1
2013-05-01 17:53:11 +09:00
Randy Mackay
3aca35777f
Copter: use mavlink fence message
...
Note: we should consider moving this send via mavlink into the fence
library
2013-05-01 17:06:58 +09:00
Randy Mackay
bab9fa25e5
Copter: add GCS failsafe
2013-04-29 21:30:22 +09:00
Randy Mackay
76d0f7f74d
Copter: fix compiler warning re unused float_int
2013-04-28 17:22:58 +09:00
Randy Mackay
d146d6aaa6
Copter: restore update_altitude to run at 10hz
2013-04-28 17:15:13 +09:00
Randy Mackay
58d1da2d80
Copter: integrate AC_Fence in place of limits
...
Lesser functionality than limits but saves more than 150 bytes and it
works
2013-04-27 11:14:07 +09:00
Andrew Tridgell
300a8d2bbc
Copter: support all 12 channels on PX4
...
last 4 channels are on the FMU pins
2013-04-25 20:10:53 +10:00
Randy Mackay
74dca6da22
Copter: move update_commands to run_autopilot fn
...
update_commands was being run in the medium_loop counter but it is
easier to understand the flow of the code if it is consolidated along
with other autopilot calls.
2013-04-24 20:59:49 +09:00
Andrew Tridgell
5ad9deecfb
Copter: cleanup some bit if tests to be clearer
...
Pair-Programmed-With: Randy Mackay <rmackay9@yahoo.com>
2013-04-23 23:03:34 +10:00
Randy Mackay
63a48f76e2
Copter: add pre-arm check of radio and accel
...
Only checks throttle channel and accelerometer scaling
2013-04-23 00:01:20 +09:00
Andrew Tridgell
d5875676b1
Copter: use a reference to DCM matrix
2013-04-22 13:26:49 +10:00
Randy Mackay
2fc25da4c3
Copter: Leonard's fix for get_loiter_accel_to_lean_angle
2013-04-21 16:27:50 +09:00
Andrew Tridgell
c53ede506d
Copter: make if statement clearer
2013-04-21 07:25:52 +10:00
Andrew Tridgell
8b31f276a2
Copter: switch to block based logs for SITL
2013-04-20 20:45:51 +10:00
Randy Mackay
a53e5f747b
Copter: add fourth yaw behaviour, look-at-home
...
Added get_wp_yaw_mode to remove duplication of checks of the
WP_YAW_BEHAVIOR parameter
2013-04-20 15:36:24 +09:00
Andrew Tridgell
02c3083f60
Copter: print flight mode as string
2013-04-20 15:18:22 +10:00
Andrew Tridgell
67484a2ea1
Copter: make copter code compatible with the new logging system
...
not fully converted yet
2013-04-20 13:52:36 +10:00
Randy Mackay
37abfdc65a
Copter: make CIRCLE_RATE a tunable parameter
...
Also bug fix to check of how many time it has rotated during a loiter
turns mission command
2013-04-20 12:03:55 +09:00
Randy Mackay
f5955d8915
Copter: auto climb and descent params removed
...
These params now reside in the AC_WPNav library
2013-04-18 14:52:21 +09:00
Randy Mackay
2b4a7d60a9
Copter: remove unused throttle modes
...
These were useful for testing the alt-hold when it was first introduced
but now they just add complexity
2013-04-17 22:14:22 +09:00
Randy Mackay
56809a9df2
Copter: remove unused nav_ok and alt_sensor_flag
2013-04-17 21:57:57 +09:00
Randy Mackay
d2bd818b2d
Copter: bug fix for auto_armed logic
...
Zero throttle when switching into an auto flight mode would cause the
motors to stop.
2013-04-17 21:28:42 +09:00
Andrew Tridgell
501eb4f0b4
Copter: made more variables static
2013-04-17 21:35:11 +10:00
Randy Mackay
a185fa950c
Copter: Jason's fix to auto disarming
...
Added check so that it only starts counting down when motors are armed.
This removes the issue in which the copter sometimes disarms shortly
aftering being armed.
2013-04-15 23:36:45 +09:00
Randy Mackay
b48864e1ad
Copter: allow CH6 tuning of compass declination
2013-04-15 21:50:44 +09:00
Randy Mackay
629d23b7e2
Copter: remove WP_SPEED and WP_RADIUS parameters
...
AC_WPNav library has equivalent params with very similar names
2013-04-14 13:27:37 +09:00
Randy Mackay
bffe4fa412
Copter: remove NAV_LAT and NAV_LON
...
Loiter and navigation controllers now combined
2013-04-14 12:09:45 +09:00
Randy Mackay
1ee825ee9a
Copter: move alt and wp checking to AC_WPNAV
...
RTL fix so that if it starts rtl-ing from above 80m it returns home
while descending instead of descending at initial position.
add get and set_target_alt_for_reporting
2013-04-14 10:39:23 +09:00
Randy Mackay
bc87118062
AC_WPNav: add get_target_alt method
2013-04-14 10:39:00 +09:00
Randy Mackay
6dbcbdcb43
AC_WPNav: limit max loiter position error
...
move interpretation of pilot input to wpnav lib
2013-04-14 10:38:58 +09:00
Randy Mackay
926c404994
AC_WPNav: Leonard's loiter target smoothing
2013-04-14 10:38:39 +09:00
Randy Mackay
553f40a99c
Copter: bug fix to loiter delay
...
change delay to seconds to allow delays longer than 65seconds
2013-04-14 10:38:30 +09:00
Randy Mackay
4de5f67a91
Copter: replace wp_nav.get_target_alt with get_destination_alt
2013-04-14 10:38:17 +09:00
Randy Mackay
5b93990e41
Copter: removed next_WP
...
Use the wp_nav.get_target_alt or controller_desired_alt in it's place
2013-04-14 10:38:07 +09:00
Randy Mackay
1516972eaa
Copter: add panorama to CIRCLE mode
...
Yaw will slowly rotate if CIRCLE_RADIUS is set to zero
Circle center is projected forward CIRCLE_RADIUS from current position
and heading
2013-04-14 10:38:01 +09:00
Randy Mackay
58ed8cd544
Copter: replace set_next_WP with direct call to wp_nav
2013-04-14 10:37:55 +09:00
Randy Mackay
49828eba7d
Copter: integrate AC_WPNav
2013-04-14 10:37:48 +09:00
Randy Mackay
3bf847f675
Copter: Jason's faster cos_yaw, sin_yaw
2013-04-02 15:50:29 +09:00
Randy Mackay
7ccb14344c
Copter: update version to 2.9.1b-dev
2013-04-01 11:47:56 +09:00
Michael Oborne
59f80410d5
Add ability to compile sensor hil with sitl
2013-03-31 16:35:23 +08:00
Andrew Tridgell
b280857025
Copter: use common angle wrap code
2013-03-29 13:14:31 +11:00
Randy Mackay
f7d977fe37
Copter: add support for GPS fix type 2D
2013-03-27 11:41:47 +09:00
Randy Mackay
597a4b912a
Copter: fix to allow building HIL_MODE_SENSORS
2013-03-18 13:41:52 +09:00
Randy Mackay
61e29173e3
Copter: remove unused crosstrack variables and parameters
...
Cross track is still calculated internally to the wpnav controller so we
should move this to a library and still report it to the ground station
2013-03-17 16:46:31 +09:00
Randy Mackay
fdcb78ccf7
Copter: leonard's smoother alt-hold transition
...
Target altitude when entering alt-hold is based on a projection from
current alt and climb rate
2013-03-17 13:24:49 +09:00
Randy Mackay
150046f2b8
Copter: GPS Failsafe implemented
...
Switches to LAND mode 5 seconds after losing GPS if you're in a flight
mode that requires a GPS
2013-03-16 17:27:46 +09:00
Randy Mackay
f9539384a1
Copter: rename failsafe to failsafe_radio
...
Makes way for separation of failsafes for throttle, gps and gcs
2013-03-16 17:14:21 +09:00
Randy Mackay
f263e81ed7
Copter: remove unused GPS and baro filters
...
Saves 24bytes of RAM
Removing the baro filter leads to noisier Baro Alt appearing in the log
so we should make the inertial nav altitude appear in the CTUN message
2013-03-16 00:20:15 +09:00
Randy Mackay
cb84ec9d9b
Copter: add current based compass compensation
2013-03-03 23:02:36 +09:00
Randy Mackay
e0506bd622
Copter: inav circle initial implementation
2013-02-26 11:35:35 +09:00
Randy Mackay
d6ff5ae261
Copter: add roll-pitch slew for auto modes
...
Added reporting of roll, pitch inputs for ACRO, AUTO
2013-02-24 14:42:04 +09:00
Randy Mackay
cbde042ec5
Copter: remove non-inav loiter and wp controllers
...
lon_speed, lat_speed changed to float
do_takeoff, do_land now set roll-pitch, yaw and nav modes specifically
removed fast_corners functionality (may need to be reimplemented with
new inertial nav controllers)
2013-02-24 14:41:52 +09:00
Randy Mackay
609676e26c
Copter: add logging of compass values
...
Removed rarely used ITERM because we didn't have enough bits in the log
mask
2013-02-24 14:41:48 +09:00
Randy Mackay
1410063a14
Copter: new ROLL_PITCH_WP_INAV roll-pitch mode
...
small corrections to allow waypoints to work with new inertial nav wp
controller
2013-02-24 14:41:40 +09:00
Randy Mackay
67c69a19ee
Copter: remove baro-only alt hold
...
Saves 8 bytes of memory and more importantly simplifies the alt hold
calculations
2013-02-24 14:41:29 +09:00
Randy Mackay
fcf102b2cf
Copter: inertial nav waypoint controller
...
#define added to allow compile time selection of traditional or inav
based loiter and wp controllers
2013-02-24 14:41:09 +09:00
Jason Short
7d5b975da2
AC: Flip code fix
...
Flight tested it today and made some flips. Throttle adjusted in Manual throttle modes. Not tested in AP throttle modes such as alt hold.
2013-02-23 13:14:11 +09:00
Jason Short
abd0fb9099
AC : global static variables should not be initialized to zero
2013-02-22 17:34:18 +09:00
Randy Mackay
9904e9f4db
Copter: update firmware version to 2.9.1-rc1
2013-02-19 13:43:36 +09:00
Randy Mackay
a0b65a262b
Copter: use scaled throttle for accel-throttle's I term
...
Accel throttle's I term is taken from scaled manual throttle
2013-02-01 22:37:25 +09:00
Randy Mackay
06a71af12f
Copter: THR_MID used to scale manual throttle
2013-02-01 22:37:16 +09:00
rmackay9
9c3b9907dd
Copter: bug fix to set sonar_alt_health to zero when disabled
2013-01-31 17:00:28 +09:00
Randy Mackay
ce370bab0c
Copter: rename CUR and CURR to CURRENT for logging
...
Based on user complaint that enable/disable was using CUR while message
was appearing as CURR
2013-01-26 17:20:41 +09:00
Randy Mackay
d2767b911c
AP_Math: switch get_distance_cm to return uint32_t
...
Includes changes required on ArduCopter and ArduPlane side as well
2013-01-26 17:04:12 +09:00
Randy Mackay
0056bfadd7
Copter: rename ROLL_PITCH_LOITER
...
new name ROLL_PITCH_LOITER_INAV makes it more clear that it should only
be used with the new inertial nav loiter controllers
2013-01-25 23:27:31 +09:00
Randy Mackay
aaecc25ac7
Copter: leonard's inav2
...
Moved loiter controller to navigation.pde
2013-01-25 15:16:35 +09:00
Randy Mackay
fd02cfe706
Copter: added set_nav_mode to control initialisation of nav controllers
...
Renamed run_navigation_controllers() to run_autopilot()
Renamed update_nav_wp() to update_nav_mode()
Renamed wp_control to nav_mode to be more consistent with roll-pitch,
yaw and throttle controllers
2013-01-25 15:16:29 +09:00
Randy Mackay
9a09f086d2
Copter: Leonard Hall's inertial nav ver 2
2013-01-23 12:34:49 +09:00
rmackay9
ab1978ad50
Copter: Leonard Hall's inertial nav based loiter
2013-01-22 18:38:00 +09:00
Robert Lefebvre
dde713aaa5
Arducopter: Backing out my changes for a new Loiter Repositioning mode. Leonard and Jonathan's work will trump this.
2013-01-20 21:32:00 +09:00
Randy Mackay
577bf865b3
Copter: update firmware version to 2.9-dev
...
The -dev extension indicates that we are post 2.9 release
2013-01-17 13:03:33 +09:00
James Bielman
5631f865b2
Update floating point calculations to use floats instead of doubles.
...
- Allows use of hardware floating point on the Cortex-M4.
- Added "f" suffix to floating point literals.
- Call floating point versions of stdlib math functions.
2013-01-16 13:52:01 +11:00
Randy Mackay
148c227d73
Copter: update firmware version to rc5
2013-01-15 12:17:41 +09:00
Randy Mackay
c1fa850d10
ArduCopter: update firmware version to 2.9-rc4
2013-01-13 20:01:09 +11:00
Randy Mackay
175f69a64f
ArduCopter: smooth throttle when switching from manual throttle to alt hold
...
new set_accel_throttle_I_from_pilot_throttle function copies the
difference between the pilot's throttle and hover throttle to the
accelerometer based throttle controller's I term.
2013-01-13 20:00:59 +11:00
Randy Mackay
fbed8b8861
ArduCopter: alphabetized the contributors list
...
Jonathan Challinger added
2013-01-13 20:00:28 +11:00
Randy Mackay
5965914039
ArduCopter: increase firmware version to 2.9-rc3
2013-01-13 20:00:25 +11:00
Andrew Tridgell
b0c710b67f
Copter: move read_AHRS() before run_rate_controllers()
...
this ensures the rate controllers use the latest data
2013-01-13 20:00:14 +11:00
rmackay9
f25f1cb3bf
ArduCopter: changed alt hold to use the sonar if enabled and healthy
2013-01-13 19:56:19 +11:00
rmackay9
21b6c78d12
ArduCopter: added get_throttle_althold_with_slew to allow slower altitude target changes
...
Improved surface tracking by using slewed althold controller
Reduced sonar mode filter to just 3 elements to reduce lag but at the possible consequence of allowing sonar noise to creep through for people with margin sonar set-ups.
2013-01-13 19:51:47 +11:00
Randy Mackay
87627d883b
ArduCopter: use new logging method for remaining packet types
...
Additional changes include renaming RAW dataflash type to IMU
2013-01-13 00:17:44 +09:00
Andrew Tridgell
af478d52bc
Copter: use the new logging methods for 2 packet types
...
the rest still need to be converted
2013-01-12 18:15:23 +11:00
Andrew Tridgell
0fe7901422
Copter: only print perf data when SCHED_DEBUG is non-zero
2013-01-12 12:06:40 +11:00
Andrew Tridgell
dcb181d2d8
Copter: use new AP_Scheduler library
2013-01-12 12:02:57 +11:00
Andrew Tridgell
2e57720444
Copter: move memcheck_init() earlier in setup
2013-01-11 10:24:21 +11:00
James Bielman
7374e5d84e
ArduCopter: Use 16-bit arithmetic when comparing event tick counters.
...
- On the ARM, once the tick counter wrapped, we stopped running events
because the wraparound case wasn't being handled correctly. Make
sure the comparison is 16 bits to prevent this.
2013-01-09 11:19:52 -08:00
James Bielman
7827a4a54a
ArduCopter: Add AP_HAL_SMACCM support.
...
- Added default configuration to "config.h".
- Added main function to run under FreeRTOS with HWF4.
2013-01-09 11:19:51 -08:00
James Bielman
ab37f833db
MS5611: Fix CONFIG_MS5611_SERIAL definitions.
...
- Make sure the values are defined as integers. We were always using
SPI rather than using I2C when desired.
2013-01-09 11:19:51 -08:00
Andrew Tridgell
e575c5eba0
Copter: read baro at 50Hz
2013-01-09 23:46:05 +11:00
Andrew Tridgell
269804e866
Copter: use barometer.accumulate()
...
this gives us more consistent timing and faster baro reads on APM1
2013-01-09 23:08:19 +11:00
Andrew Tridgell
860f4b2605
Copter: merge the latest 2.9 changes into master
2013-01-08 14:37:40 -08:00
Andrew Tridgell
d11dde578f
Copter: a useful bit of timing debug code
...
enable when looking at main loop timing
2013-01-07 11:07:44 +11:00
Andrew Tridgell
d952ccf968
Copter: added main_loop_ready() function
...
this tells us when the main loop is ready to run. MAVLink won't send a
message if the main loop could run.
2013-01-07 11:07:34 +11:00
Andrew Tridgell
c48714be16
Copter: enabled PX4 sensors
2013-01-05 20:39:31 +11:00
James Bielman
264db3670e
AP_Baro: Add CONFIG_MS5611_SERIAL option to choose between SPI and I2C.
...
- Update ArduCopter and ArduPlane modules to pass the correct serial
driver to the MS5611 driver.
- Update barometer examples, assuming SPI.
2013-01-03 13:48:06 -08:00
Andrew Tridgell
94e3322e24
Copter: fixed build on px4
2013-01-02 22:09:02 +11:00
Andrew Tridgell
e56a7eacec
Copter: don't pass board version to motors
2013-01-02 15:28:34 +11:00
Andrew Tridgell
ead38f917f
Copter: use GRAVITY_MSS
2013-01-02 14:45:08 +11:00
rmackay9
228ad2198f
ArduCopter: update firmware version to 2.9-rc2
2013-01-02 09:55:37 +11:00
rmackay9
677b38a48e
ArduCopter: first implementation of surface tracking using sonar
...
Note: not yet enabled as part of any flight mode
2013-01-02 09:55:37 +11:00
rmackay9
68b62abd38
ArduCopter with the new Camera and Relay classes for APM1 and APM2.
...
All changes by Sandro Benigno
2013-01-02 09:55:37 +11:00
rmackay9
e850ab7ccd
ArduCopter: add AUTO_VELZ_MIN, AUTO_VELZ_MAX and PILOT_VELZ_MAX to allow better control of climb/descent rate in auto and manual throttle modes
2013-01-02 09:24:31 +11:00
Craig@3DR
0ed25cf719
Global change all references from
...
GPS_PROTOCOL_MTK16
to
GPS_PROTOCOL_MTK19
2013-01-02 09:24:31 +11:00
rmackay9
466097b383
ArduCopter: use inertial nav for current altitude and climb rate
2013-01-02 09:22:51 +11:00
rmackay9
5ba363b007
ArduCopter: move gcs_check function (which sends to ground station) to run when 50hz loop is not running
...
Also removed redundant heartbeat message
2013-01-02 09:21:35 +11:00
rmackay9
bd0e018ca0
ArduCopter: restore auto-trim method but now use AHRS.add_trim
2013-01-02 09:20:08 +11:00
Robert Lefebvre
6e64b1b357
ACM: Precision Loiter RePositioning code.
...
Protected behind a #define
2013-01-02 09:19:39 +11:00
rmackay9
e6519330f4
ArduCopter: remove unused rc_override variables to save 21 bytes
2013-01-02 09:19:17 +11:00
rmackay9
ac8af9a53f
ArduCopter: Leonard Hall's changes to alt hold including adding low pass filter to climb rate
...
get_throttle_rate_stabilized changed to simply update the target altitude instead of talking directly to the rate controller.
get_throttle_althold changed to use sqrt of distance when calculating the desired rate towards the target altitude.
added reset of accel based throttle PID's I term.
unrelated small bug fix from Randy to allow CH6 tuning of throttle rate D term.
2013-01-02 09:19:17 +11:00
rmackay9
d926360e81
ArduCopter: move gcs updates to run only when there are 4ms of spare time before the next 100hz iteration starts
2013-01-02 09:14:31 +11:00
rmackay9
6da68c53a5
ArduCopter: bug fix so AP_Limits does not use up memory if it is disabled
2013-01-02 09:13:42 +11:00
rmackay9
5633164fa0
ArduCopter: bug fix for compass.accumulate check in main loop (millis vs micros issue)
2013-01-02 09:12:40 +11:00
rmackay9
8e032b89ee
ArduCopter: create 2.9 branch and update firmware version
2013-01-02 09:10:40 +11:00
Andrew Tridgell
06357c40f2
Copter: use new functions
2012-12-20 14:53:22 +11:00
Andrew Tridgell
a02f723f3a
Copter: fixed HIL builds
2012-12-20 14:52:37 +11:00
Andrew Tridgell
9e986801c9
Copter: fixed SITL for ArduCopter
2012-12-20 14:52:34 +11:00
Andrew Tridgell
08b1c2d590
Copter: fixed GPS init
2012-12-20 14:52:33 +11:00
Pat Hickey
d5d97be837
ArduCopter: add param loader properly implement parameters
...
* thanks tridge!
2012-12-20 14:52:29 +11:00
Pat Hickey
5e63491994
ArduCopter: fix issues with HAL/HIL mixup and baro/compass instances
2012-12-20 14:52:29 +11:00
Pat Hickey
21d0da84a6
ArduCopter: temporarily disable AP_Param::setup_sketch_results
...
* rebased away tridge's AP_Param changes as they seemed possibly buggy?
2012-12-20 14:52:29 +11:00
Pat Hickey
a0151aa66c
ArduCopter: fix cliSerial null ptr, do AP_Param::setup_sketch_defaults
...
* plus make SITL DataFlash available.
2012-12-20 14:52:29 +11:00
Pat Hickey
2aa4657315
ArduCopter: changes to use CONFIG_HIL_BOARD
2012-12-20 14:52:28 +11:00
Pat Hickey
ade7099d75
ArduCopter: add AP_HAL_MAIN
2012-12-20 14:52:28 +11:00
Pat Hickey
5bd7046a95
ArduCopter: sketch cpp builds!
2012-12-20 14:52:28 +11:00
Pat Hickey
7af03127f6
ArduCopter: more work
2012-12-20 14:52:28 +11:00
Pat Hickey
70f4739522
ArduCopter: more fixes
2012-12-20 14:52:28 +11:00
Pat Hickey
f281d9265e
ArduCopter: reworked sonar analog source creation
2012-12-20 14:52:28 +11:00
Pat Hickey
d9e0bbbbab
ArduCopter: first pass at AP_HAL porting
...
* changed all the byte types to uint8_t
* fixed up much of the serial stuff
2012-12-20 14:52:27 +11:00
Pat Hickey
a4f1f6a5db
AP_Progmem: fix dependencies for all sketches touched by AP_HAL_AVR
2012-12-20 14:51:28 +11:00
Pat Hickey
3f1d9d7f69
AP_Param: #include <AP_Param.h> fixups for libraries & sketches
...
* I mostly went through with grep and added an #include <AP_Param.h> below
every #include <AP_Common.h>. Not all of these example sketches might
strictly need AP_Param.
2012-12-20 14:51:19 +11:00
Jason Short
19ae5c30eb
ACM : Formatting
2012-12-13 20:12:39 -08:00
rmackay9
047f848cc7
ArduCopter: remove ThirdOrderCompFilter from list of includes
2012-12-10 09:14:44 +09:00
rmackay9
0f7bb79d89
ArduCopter: add comments to tuning parameters.
...
Use RC_CHANNEL types as defined by RC_Channel library.
Remove unused definitions.
2012-12-09 16:44:42 +09:00
rmackay9
8c2423f618
ArduCopter: code clean-up. Changed update_nav_wp to use a switch statement and relocated to navigation.pde
2012-12-09 15:24:19 +09:00
rmackay9
b4e5176e2a
ArduCopter, AP_InertialSensor: restore mpu6k sample rate to 200hz but keep default filtering at 42hz.
2012-12-09 14:27:33 +09:00
Robert Lefebvre
0eb57bf93d
ACM: TradHeli
...
Fix to make update_throttle_cruise work with stab_throttle scaling.
2012-12-08 15:12:39 -05:00
rmackay9
9dd978576b
ArduCopter: auto yaw changes to allow pilot override of yaw during missions
...
Added set_yaw_mode to better control of yaw controller changes and variable initialisation.
Replaced AUTO_YAW mode with separate yaw controllers YAW_LOOK_AT_NEXT_WP, YAW_LOOK_AT_LOCATION, YAW_LOOK_AT_HEADING.
Pilot manual override of yaw causes yaw to change to YAW_HOLD (i.e. manual yaw) until next waypoint is reached.
Added get_yaw_slew function to control how quickly autopilot turns copter
Changed YAW_LOOK_AHEAD to use GPS heading and moved to new get_look_ahead_yaw function in Attitude.pde
Renamed variables: target_bearing->wp_bearing, original_target_bearing->original_wp_bearing.
Removed auto_yaw_tracking and auto_yaw variables and update_auto_yaw function as they are no longer needed.
Simplified MAV_CMD_CONDITION_YAW handling (do_yaw). We lose ability to control direction of turn and ability to do long panorama shots but it now works between waypoints and save 20bytes.
2012-12-08 14:23:32 +09:00
rmackay9
99b32a39c4
ArduCopter: InertialNav time constant CH6 tuning changed to only update enabled axis
2012-12-07 13:01:40 +09:00
rmackay9
39d524212f
ArduCopter: allow accel based throttle controller to be enabled/disabled with the new THR_ACC_ENABLE parameter.
...
When disabled the original velocity based throttle controller is used.
2012-12-06 10:31:57 +09:00
rmackay9
a5bb54e36e
ArduCopter: RTL clean-up and slightly improved landing sensor
...
Consolidated RTL state to be captured by rtl_state variable.
Combined update_RTL_Nav and verify_RTL functions which performed the same function but one was for missions, the other for the RTL flight mode.
Renamed some RTL parameters and global variables to have RTL at the front.
Landing detector now checks accel-throttle's I term and/or a very low throttle value
2012-12-06 10:31:52 +09:00
rmackay9
072ffec493
ArduCopter: allow INERTIAL_NAV to be enabled separately for horizontal and vertical position
2012-12-06 10:31:41 +09:00
rmackay9
d7f76ebd87
ArduCopter: add tuning of throttle rate controller's I term (THROTTLE_KI)
2012-12-06 10:31:25 +09:00
rmackay9
7b4ed2d227
ArduCopter: restored landing detector to landing throttle mode.
...
Added LAND_SPEED parameter to control the rate of descent for the last 10m of a landing.
Added CH6 tuning for accel based throttle controller.
2012-12-06 10:31:20 +09:00
rmackay9
a94826f182
ArduCopter: add set_throttle_mode to better control initialisation of variables
2012-12-06 10:31:04 +09:00
rmackay9
1036b35128
ArduCopter: added back in angle boost and recombined for heli and multicopter
2012-12-06 10:30:55 +09:00
rmackay9
3cbef57c64
ArduCopter: first merge of leonard's accel based altitude controller plus other changes from Randy
...
Changes include:
New low-level get_throttle_accel function takes target acceleration and compares vs earth-frame Z accelerometer values to produce output to motors.
Higher level throttle controllers modified to call new get_throttle_accel controller
Throttle_rate_stabilized controller added which maintains a desired climb/descent rate
Throttle_land controller added - descends using normal auto throttle controller to 10m then descends at 50cm/s
Multiple throttle modes added including landing mode
Land flight mode no longer needs GPS
Throttle cruise maintenance moved to update_throttle_cruise function
2012-12-06 10:30:49 +09:00
Robert Lefebvre
1d589c0b7d
ACM: TradHeli
...
Fixes for Attitude rate controllers.
2012-12-04 14:42:04 -05:00
Robert Lefebvre
315a7e8000
ACM: Yaw Look Ahead Changes
2012-12-04 13:26:41 -05:00
Robert Lefebvre
9130045298
ACM: Code Cleanup
2012-11-30 17:05:12 -05:00
rmackay9
8141f0b600
ArduCopter: bug fix - increase mpu6k sample rate to 100hz
2012-11-30 23:49:18 +09:00
Andrew Tridgell
6fbf5ec8f2
Copter: update ArduCopter for new ins interface
2012-11-30 07:15:18 +11:00
Robert Lefebvre
07d7d90882
ACM: TradHeli
...
Bringing in Low Pass Filter for Rate Controllers
2012-11-26 21:51:23 -05:00
Robert Lefebvre
6b8c39dd10
ACM: Creating Yaw_Look_Ahead yaw mode.
...
This function is not fully tested yet.
2012-11-26 21:37:13 -05:00
Robert Lefebvre
3f0e8dd358
ACM: TradHeli
...
Bringing in Low Pas Filter
Commented out because it does not build.
Needs updates to Low Pass Filter Lib
2012-11-26 21:21:12 -05:00
Robert Lefebvre
e8d619acad
ACM: Begin creation of TradHeli rate control.
...
May affect Multi-Rotors.
2012-11-26 21:02:41 -05:00
Robert Lefebvre
6b1fee767a
ACM: TradHeli
...
Creating Stab_Collective Function to allow for different collective ranges between Stabilize and other modes.
This makes for a smoother collective action in Stabilize mode with manual throttle, while still allowing full collective travel in Acro and other modes.
2012-11-26 19:37:20 -05:00
Robert Lefebvre
95eeda7cf7
ACM: TradHeli
...
Removing Angle Boost function.
Does not make sense for helis due to aerodynamics. Can cause more problems than it solves.
2012-11-26 18:58:21 -05:00
Robert Lefebvre
8056b78c55
ACM: TradHeli
...
Remove Rate I-term reset when throttle stick is on the bottom. This could be very bad for helis since it's plausible to use full downstick while flying.
There is obviously a risk here of building up a false I-term on the ground but this isn't a good solution for that anyway.
Also removed what appears to be some deadwood.
2012-11-26 18:49:24 -05:00
Andrew Tridgell
5818aaad42
Copter: fixed build error
...
thanks to Marco for pointing this out
2012-11-24 20:39:35 +11:00
Andrew Tridgell
cd07d965a7
Copter: ported RSSI_PIN option from ArduPlane
...
this is useful for OSD users
2012-11-22 20:59:33 +11:00
rmackay9
3372355e07
ArduCopter: remove commented out remnants of roll_scale_d and pitch_scale_d
2012-11-22 12:50:39 +09:00
Andrew Tridgell
bcae83c4f6
ACM: make it possible to run CLI on radio port in ArduCopter
2012-11-21 21:41:34 +11:00
rmackay9
07a7a1acd8
ArduCopter: replaced digitalRead and digitalWrite with faster calls
...
improved performance logging to dataflash
2012-11-19 01:16:07 +09:00
Robert Lefebvre
9c6e914bf8
Added Leonard to Contributor List.
2012-11-16 15:43:03 -05:00
rmackay9
258442770d
ArduCopter: flight mode changes ignored while in throttle failsafe
...
reaction time to flight mode changes (when not in failsafe) reduced from 0.6 seconds to 0.1 seconds
2012-11-13 12:50:51 +09:00
rmackay9
dcd98eee78
ArduCopter: remove some variables no longer required with introduction of AP_state
2012-11-12 12:41:25 +09:00
rmackay9
ac5dcc8d49
ArduCopter: remove last remanants of rate_d to resolve compiler warning of unused variables
2012-11-12 12:35:58 +09:00
Jason Short
c1b759d5d8
ACM: Added a speed filter for throttle cruise, increased alt change rate for alt hold, increased the max climb_rate reporting
2012-11-11 18:17:33 -08:00
Jason Short
9e0b0b9fcd
ACM : loging ApState at faster rate
2012-11-11 18:00:10 -08:00
rmackay9
bcb9519fd7
ArduCopter: renamed system bitmap to ap_system to resolve desktop compile issues
2012-11-11 22:42:10 +09:00
rmackay9
95f6357d35
ArduCopter: fix APM2 build
2012-11-10 22:06:23 +09:00
Jason Short
e4cec91e59
ACM : Arducopter Added ap state bitfield, system bitfield
2012-11-09 22:15:15 -08:00
Jason Short
cdabc3878b
ACM: Arducopter - remove the stabilize D scheduling
2012-11-09 22:15:15 -08:00
Jason Short
d2a0913b2d
ACM : formatting
2012-11-09 22:15:15 -08:00
rmackay9
b13264c884
AP_InertialNav: reanme AP_InertialNav and ThirdOrderCompFilter classes to resolve desktop build compiler errors
2012-11-07 22:24:00 +09:00
rmackay9
ad431d2f25
ArduCopter: fixed HIL build caused by optical flow semaphore changes
2012-11-07 21:13:34 +09:00
rmackay9
1f801714e8
ArduCopter: incorporate new version of inertial navigation
...
Moved several navigation functions from ArduCopter.pde to navigation.pde
2012-11-07 19:21:31 +09:00
rmackay9
a1b4ec6d0e
ArduCopter: move to use new INS library instead of IMU library
2012-11-07 19:21:09 +09:00
Jason Short
e138b0a1d7
ACM: Added simple mode bearing logging for bug hunting
2012-10-28 12:12:38 -07:00
rmackay9
78316adf75
ArduCopter: replace Serial.print with Serial.print_P to save memory.
...
Includes replacing flight_mode_strings with print_flight_mode function.
SendDebug macro replaced with direct Serial.print_P calls.
2012-10-22 16:45:24 +09:00
Jason Short
a0752dc7dc
ACM Acceleration management
...
removed unused waypoint_radius var
removed slow_wp
updated speed management system to maintain a constant acceleration or deceleration of 1m/s
changed version to 2.8.1a
2012-10-21 14:32:39 -07:00
rmackay9
a37a9b5b67
ArduCopter: updated firmware version to 2.8
2012-10-20 09:50:53 +09:00
Pat Hickey
d4bb8a10d7
Update ArduCopter and ArduPlane dependencies on AP_Menu
2012-10-18 20:53:39 -07:00
Robert Lefebvre
592f4040fd
Changed RLT Yaw Mode for TradHeli. Also a few comment cleanups.
2012-10-18 16:39:05 -04:00
rmackay9
1c08e48b4b
ArduCopter: updated firmware version to 2.7.4-Zeta
2012-10-18 23:30:28 +09:00
rmackay9
583f2e49a3
ArduCopter: integrated Leonard Hall's improved ACRO mode
2012-10-18 23:24:34 +09:00
rmackay9
d2912e4e01
ArduCopter: added spi_semaphore to stop conflicts between dataflash and optical flow sensor on APM1
2012-10-18 17:04:44 +09:00
rmackay9
9e3c2dd105
ArduCopter: updated firmware version to 2.7.4-Epsilon
2012-10-17 19:27:11 +09:00
rmackay9
8519fe55d3
ArduCopter: more out-of-date commented out code removed
2012-10-17 19:25:14 +09:00
rmackay9
956b347d68
ArduCopter: updated firmware version to 2.7.4-Delta
2012-10-17 10:20:41 +09:00
rmackay9
4016f3ba85
ArduCopter: update version information ahead of testing
2012-10-15 18:15:38 +09:00
LeonardTHall
d7b7e1cefa
New Yaw controller using rate feed forward and stabilize.
...
Signed-off-by: LeonardTHall <LeonardTHall@gmail.com>
2012-10-15 11:37:49 +09:00
rmackay9
997fe85880
ArduCopter: fixed acro mode
...
Changes included:
Removing earth frame roll_rate_trim, pitch_rate_trim and yaw_rate_trim.
Switch ACRO mode to use YAW_ACRO instead of YAW_HOLD.
Changed YAW_ACRO to use stabilize yaw when axis_enabled.
Reset ACRO roll, pitch and yaw targets to current attitude when first entering ACRO.
2012-10-14 17:47:46 +09:00
rmackay9
1e79d265a1
ArduCopter: remove unnecessary (probably slightly harmful) extra barometer read
...
The barometer reads including reading temperature was all moved to a timer but this extra read (originally to read the temperature) was probably forgotten.
2012-10-11 18:31:10 +09:00
rmackay9
cf3e49eea2
ArduCopter: changed sin_pitch and sin_roll to faster equivalents
2012-10-11 17:54:42 +09:00
Andrew Tridgell
601fe89baa
ACM-HIL: fixed optflow declaration
2012-10-11 11:51:25 +11:00
Pat Hickey
da374f9043
ArduCopter: Provide AP_Semaphore instance for SPI3 bus on APM2.
2012-10-09 11:39:39 -07:00
rmackay9
c0ad98be31
ArduCopter: failsafe added to shutdown motors if mainloop fails
2012-10-09 12:30:17 +09:00
rmackay9
61d0c8e35c
ArduCopter: added AP_Semaphore to list of includes
2012-10-06 12:41:58 +09:00
rmackay9
e375a27058
ArduCopter: prioritise rate controllers, rate controller targets converted to body frame
2012-10-03 14:10:31 +09:00
rmackay9
95763e610b
ArduCopter: allow DMP to run in parallel with DCM
...
Parallel DMP can be enabled by #define SECONDARY_DMP_ENABLED in APM_Config.h
New DMP dataflash log type added to allow easy comparison with DCM
2012-09-30 00:25:40 +09:00
rmackay9
41fbb19cf5
AP_InertialSensor_MPU6000: replaced _cs_pin parameter with #define and saved 1 byte of memory
...
Updated ArduCopter, ArduPlane and example sketches in AP_InertialSensor, AP_IMU and AP_AHRS libraries because they no longer need to pass in cs_pin to the constructor
2012-09-28 19:21:59 +09:00
rmackay9
ed881117e0
ArduCopter: updated version to 2.7.4-Beta
2012-09-25 23:39:15 +09:00
rmackay9
b2f12c4854
ArduCopter: optical flow initialisation changes now that optical flow library automatically works on APM1, APM2 and APM2.5
2012-09-24 18:39:33 +09:00
rmackay9
93ae29a3e9
ArduCopter: added throttle curve (although disabled by default) for all multicopters
2012-09-18 23:05:08 +09:00
Andrew Tridgell
5fd39bb928
ACM: updates for new GPS detection
...
a GPS can now be attached after startup
2012-09-17 14:45:47 +10:00
rmackay9
303ca11c4c
HIL: changes to fix HIL for ArduCopter after recent timing changes.
...
Changes include using AP_PeriodicProcess and calling imu.init even in HIL mode
2012-09-15 18:42:56 +09:00
rmackay9
9e66b555cb
ArduCopter: removed INSTANT_PWM from ArduCopter and AP_Motors library
2012-09-13 21:31:13 +09:00
Jason Short
834f961409
ACM : Fix enduf
2012-09-10 21:25:53 -07:00
Jason Short
4c8e257ea2
ACM : forced setup_show to dump params during log dump for better analysis.
2012-09-10 20:52:30 -07:00
Jason Short
34e07c826f
ACM : Added centralized Iterm logging at a lower rate. Logs all iterms.
2012-09-10 20:26:48 -07:00
Andrew Tridgell
841d2700b6
ACM: use spare CPU cycles to read the magnetometer
2012-09-10 11:38:18 +09:00
rmackay9
fd110a2723
ArduCopter: modified mainloop timing to be in sync with the arrival of new data from the IMU.
...
This reduces the maximum delay between when new sensor data arrives and when it is actually used by about 5ms.
2012-09-10 11:37:53 +09:00
Andrew Tridgell
f97104b435
ACM: use compass.accumulate() in ArduCopter
...
this gives us a much less noisy magnetometer
2012-09-08 10:06:04 +10:00
rmackay9
5073e56c06
ArduCopter: upgraded firmware version to 2.7.3
2012-09-02 12:58:16 +09:00
rmackay9
c9d34c1737
ArduCopter: fixes to allow AP_Mount to work on APM1 with original default channels and fix to reenable support for 3-axis gimbals on APM2.
...
Channels 5 to 11 changed to RC_Channel_aux.
Removed channel 9 because APM_RC doesn't support it in any case.
Updated EEPROM format version to 119 because of the change to RC_Channel_aux and because k_param_rc_11 moved to be after k_param_rc_10.
2012-09-02 12:51:23 +09:00
Craig Elder
274b2e2143
Arducopter: Release 2.7.2
2012-08-31 19:18:10 -07:00
Jason Short
082913efd4
ACM : revert back to the 2.6 climb rate calc
...
The current filter is outputting wild oscillations.
2012-08-28 21:22:07 -07:00
Craig Elder
d8a2bfb9e8
Arducopter: Preparing for 2.7.2 Release
2012-08-28 18:30:41 -07:00
Jason Short
9d64bea2ef
ACM: Altitude Adjust
2012-08-28 15:40:08 -07:00
Jason Short
98cc65862d
ACM : Log Timing
2012-08-28 15:40:08 -07:00
uncrustify
4021a64747
uncrustify ArduCopter/ArduCopter.pde
2012-08-21 19:19:50 -07:00
Andrew Tridgell
6d11940ada
AHRS: removed Quaternion build support from APM/ACM/rover
2012-08-22 10:42:21 +10:00
Andrew Tridgell
e9928e78de
ACM: fixed TradHeli build
2012-08-22 09:55:31 +10:00
Robert Lefebvre
575b99b4be
TradHeli: Creating Flybar Acro mode.
2012-08-21 16:54:01 -04:00
rmackay9
75459b09be
ArduCopter: changed reset_throttle_counter to uint8_t to get rid of overflow bug that was preventing target altitude from being locked in after pilot input down throttle.
2012-08-19 11:50:35 +09:00
Jason Short
988d0c98fc
ACM : Alt hold adjustment - made angle boost work during alt hold changes.
...
increased length of delay when reverting to automatic hold to deal with latency of baro sensor
2012-08-18 09:30:46 -07:00
rmackay9
5b6f7f0012
ArduCopter: modified altitude hold so that 1 second slow down period is executed after pilot moves throttle back into deadzone
2012-08-18 21:45:49 +09:00
Jason Short
770956a3fd
ACM : Made control_roll and pitch global for logging; made yaw towards waypoint use initial angle and not a recalculated angle to deal with wiggles as we approach WP
2012-08-16 15:39:50 -07:00
rmackay9
36f947acb9
ArduCopter: changed all "int" to "int16_t" and a few "long"s to "int32_t".
...
Also moved "simple_counter" variable from global scope to the "update_simple_mode" function which is the only place that it's actually used.
2012-08-16 20:04:46 +09:00
Jason Short
a4bc5950cf
ACM: Added a filtered version of Location for GPS lag.
...
I did this because when you are close to a WP the Yaw angle can go a bit wacky as the location jumps around. The filtered loc is only used in the wp_distance calculation now.
2012-08-14 14:11:51 -07:00
Jason Short
993c89c4f8
ACM: Revved the version
2012-08-14 14:11:51 -07:00
Jason Short
b01a71c4b9
ACM: Toy mode updates - added second toy mode
2012-08-11 22:37:27 -07:00
Andrew Tridgell
81440a1b09
AHRS: fixed build
...
AP_Airspeed.h is now needed to build AHRS
2012-08-11 12:22:55 +10:00
Jason Short
3ad08b7ffc
ACM : Added larger WP radius for fast waypoints so we don't loose speed angling in on the WP at the last second.
2012-08-10 10:02:32 -07:00
Jason Short
02649f3f11
ACM : Arducopter.pde
...
command_nav_index upped to in16t for negative number
renamed trim flag > CH7_flag
Added fast_corner var
removed unused alt vars
Alt hold I term update
2012-08-09 16:59:43 -07:00
Amilcar Lucas
0b0b9c29a2
Allow fully independent operation of two AP_Mount instances
2012-08-08 23:11:23 +02:00
Amilcar Lucas
9cc705939a
Add a second mount instance
2012-08-08 23:07:25 +02:00
Andrew Tridgell
fb26160d3b
ACM: change to use get_bearing_cd() instead of get_bearing()
2012-08-08 12:12:30 +10:00
Andrew Tridgell
c2a4d59132
AP_Param: update ArduCopter core for new AP_Param interface
2012-08-08 12:11:57 +10:00
Amilcar Lucas
d9f1140278
ArduCopter: Use generic channel names for AP_Mount servos.
...
This simplifies mission planner, the same code can be used for plane and copter now.
2012-08-06 23:33:51 +02:00
Amilcar Lucas
f14237126a
Add me :)
2012-08-06 00:40:12 +02:00
Amilcar Lucas
107155fa1a
AP_Mount: Allow using any RC channel to control any of the mount axes.
...
This has the added benefit of saving 60 bytes and simplifying Mission Planner gui.
Moved some code from RC_Channel_aux to AP_Mount class
The servos get written by the update_mount_position() function, this simplifies main()
PS: The beauty of using libraries: I did not have to touch a single line of ArduPlane's code!
2012-08-05 23:48:57 +02:00
Amilcar Lucas
b8c7b8a786
RC_Channel: Allow each channel to know who they are, this simplifies the enabling and output function calls.
2012-08-05 23:08:31 +02:00
Amilcar Lucas
4ba847c449
The mount type must be updated periodically
2012-08-04 18:44:08 +02:00
rmackay9
c091c8e0e6
ArduCopter: bug fix to reset yaw target when zero and when in stabilize or acro mode.
2012-08-01 12:15:02 +09:00
Andreas M. Antonopoulos
de85442c36
AC2.7.1: Updated version and tag
2012-07-31 13:11:17 -07:00
rmackay9
5cb4a88292
ArduCopter: reset target yaw when throttle is zero (except if failsafe has been triggered)
2012-07-28 23:05:05 +09:00
rmackay9
670a66667f
ArduCopter: fixed HIL build by removing ability to change _kp and _kp_yaw gains (used for accel and gyro sensor mixing)
2012-07-28 16:22:35 +09:00
rmackay9
014f5aae99
ArduCopter: added DMP_ENABLE #define and CH6 tuning value for AHRS_KP
2012-07-28 14:21:07 +09:00
Michael Oborne
f4705577c8
AC fix sitl attitude hil build
2012-07-24 21:18:36 +08:00
Andreas M. Antonopoulos
80cf794c86
AC: ArduCopter 2.7 release candidate - updated THISFIRMWARE constant.
2012-07-21 17:52:06 -07:00