Required to prevent acquisition of GPS mid flight causing unwanted change in position and velocity
A distinction has been mad between the arm and disarm transition and the decision to use position hold mode (formerly static mode)
When regaining GPS after a timeout, an offset is applied when fusing GPS velocity so that GPS velocity and position data as fused by the EKF is kinematically consistent.
This velocity offset is also accounted for when fusing air data so that wind estimates are not corrupted when the GPS position offset is being pulle back to zero.
The intended behaviour is that the EKF position will be pulled back to the GPS position at a rate of 5m/s for planes and 1 m/s for copters. This avoids large deviations in trajectory when GPS is regained.
When on the ground it is likely the flow sensor will be returning data that does not meet the minimum quality requirements selected.
The previous check was for the presence of valid data. This has been loosened to look for the presence of data.
When the vehicle becomes airborne, the quality of flow data normally improves as the image comes into focus.
1) Un-used public methods to report height and position drifting have been removed
2) A time-out has been added to the airspeed innovation consistency check so that if we are relying on airspeed to constrain velocity drift, a filter divergence or other fault that causes the airspeed to be continually rejected will trigger a change in health status.
3) A timeout of velocity, position or height measurements does not cause a filter fault to be reported. Timeouts can be due to sensor errors and do not necessarily indicate that the filter has failed.
4) Time-outs of various measurements are used to present a consolidated bitmask which inidicates which parts of the solution can be used, eg attitude, height, velocity, relative position, absolute position, etc.
The time required for GPS to be lost or rejected before vehicles with airspeed sensors either reset to GPS or invoke the zero side-slip assumption to constrain drift has been reduced from 15 to 10 seconds
A duplicate zeroing of the GPS position offset has been removed
If the vehicle is a non hovering vehicle (eg a plane) then the speed at which the GPS offset is pulled back to zero after a reset is increased from 1 to 3 m/s
This also improves recovery from bad inertial data for planes
Doing this can cause large height and height rate errors if large GPS velocity errors cause the GPS tn be rejected for long enough to cause a timeout and reset of states.
This reverts commit 13df6fb1c9.
This patch was a result of an incorrect merge of the optflow branch
into master. It reintroduced the bug fixed by this commit:
AP_NavEKF : Fix bug in reset of GPS glitch offset
8aa267f75f
This provides the calling vehicle software the abiity to request the EKF to not use GPS.
An integer is returned that indicates the type of operation available:
0 = request rejected (request will only be accepted if the EKF is in static mode, eg pre-armed)
1 = request accepted, attitude, vertical velocity and position estimates available
2 = request accepted, attitude, height rate, height, horizontal velocity and relative position estimates available
This takes into account the inter-sampling delay between the flow driver and the APM software which depends on the rate at which the dirver is being checked. This is 50Hz for plane and rover, and 200Hz for Copter.
This patch reduces the level of 5Hz and 10Hz 'pulsing' heard in motors due to GPS and altimeter fusion which cause a small 5Hz and 10Hz ripple on the output under some conditions. Attitude, velocity and position state corrections from GPS, altimeter and magnetometer measurements are applied incrementally in the interval from receiving the measurement to the predicted time of receipt of the next measurement. Averaging of attitude state corrections is not performed during periods of rapid rotation.
Time stamps are now explicitly initialised to the current IMU time to avoid unwanted activation of timeout logic on filter start and the various calls to the hal.scheduler->millis() object have been consolidated.
Unused variables have been removed
If the inertial solution velocity or position needs to be reset to the GPS, the stored state history for the corresponding states should also be reset.
Otherwise the next GPS measurement will be compared to an invalid previous state and will be rejected.
The position state should be reset to a GPS position corrected for velocity and measurement latency. This will make a noticeable difference for high speed flight vehicles, eg 11m at 50m/s
Re-initialisation of the magnetic field states and yaw angle is now only performed a maximum of two times after start-up.
Once when coming out of static modefor the first time (first arm event)
Again (for copter only) when the altitude gain above the arming altitude exceeds 1.5m
this prevents magnetic interference present at arming (eg arming on a metal roof)from corrupting the magnetic field states enough to cause bad heading errors and toilet bowling on copter
(Plane Only) If the yaw and GPS heading disagree by more than 45 degrees on takeoff, then the magnetometer is declared as failed. The heading is then reset based on the difference between GPS ground track and stgate velocity vector.
Magnetometer fusion uses corrected data and bias states are initialised to zero. This allows the compass to be switched in flight.
For persistent compass errors that trigger a timeout, the compass is not permanently failed, however for non-forward fly vehicles the compass weighting is reduced.
The GPS glitch offset was being zeroed during position resets. This caused the filter to reject subsequent GPS measurements if the GPS error persisted long enough to invoke a timeout and a position reset.
