- new IMU driver structure with state machine (no sleeps in bus thread)
- verify all configured registers and trigger reset on failure
- detect if DIO1 or DIO2 are actually connected for data ready interrupt usage
- don't use CRC-16 on burst transfers except for verified lots
- generate PWM_MAIN 1-14
- generate PWM_AUX 1-8
- generate PWM_EXTRA 1-8
- px4io and pwm_out directly read configuration parameters
- only available and active physical outputs are actually shown for configuration
- overall saves flash despite adding many new parameters
- fmu-v5 debug and stackcheck builds now need to be CONSTRAINED_FLASH to fit
- delete unused holybro_durandal-v1_stackcheck build (also CONSTRAINED_FLASH)
BOARD_INDICATE_ARMED_STATE was only set during arming, so an external
component might have reset the board during param save, leading to param
loss.
This extends the API to trigger the arming state also while the shutdown
lock is taken.
- simple state machine to reset, configure, etc
- checked register mechanism (sensor will reset itself on configuration error)
- configured in 16 bit mode (1320 LSB/Gauss instead of 330 LSB/Gauss)
- adjusted orientation handling in driver to match datasheet as closely as possible
- in many external compass units the rotation was wrong and very difficult to actual determine how to set correctly
It cause bad transfers on a Kopis 2, though not on a bench KakuteF7 unit.
Not sure if this is a single case.
nsh> icm20689 status
INFO [SPI_I2C] Running on SPI Bus 4
INFO [icm20689] FIFO empty interval: 1000 us (1000.000 Hz)
icm20689: transfer: 46375 events, 6790549us elapsed, 146.43us avg, min 54us max 1709us 81.564us rms
icm20689: bad register: 0 events
icm20689: bad transfer: 4284 events
icm20689: FIFO empty: 0 events
icm20689: FIFO overflow: 1 events
icm20689: FIFO reset: 2 events
icm20689: DRDY interval: 375585 events, 124.93us avg, min 99us max 250us 2.322us rms
INFO [drivers_accelerometer] /dev/accel device instance: 0
INFO [drivers_accelerometer] calibration scale: 1.02174 0.99918 0.98338
INFO [drivers_accelerometer] calibration offset: 0.76124 -0.00725 -0.16437
INFO [drivers_gyroscope] /dev/gyro device instance: 0
INFO [drivers_gyroscope] calibration offset: -0.08153 0.02432 0.00050
- skip avionics rail voltage check when USB connected
- skip forced reboot on USB disconnect if circuit breaker set
- avionics voltage preflight check don't silently fail if system_power unavailble
- explicitly set supply check circuit breaker (CBRK_SUPPLY_CHK)
- always check with state machine before reboot/shutdown
- respect BOARD_HAS_POWER_CONTROL (shutdown from command, low battery, power button)
- px4_shutdown_request add optional delay and always execute from HPWORK
- px4_shutdown_request split out px4_reboot_request
- increase stack sizes to run cleanly under stackcheck
- this is likely overkill for most boards, but using stackcheck to set our minimum ensures we have a very safe margin on regular builds and it's something we can currently afford
- remove holybro_durandal-v1_stackcheck from test rack (there's only one unit)
- update to NuttX with stm32f4 and stm32f7 SPI DMA internal buffers
- remove explicit DMA buffer allocations from new IMU drivers
- restore original BOARD_DMA_ALLOC_POOL_SIZE
- decrease SPI DMA thresholds based on fmu-v2/v3/v4/v5 bench testing
Removes the calibration on startup, as these values were overwritten by
the system calibration values anyway.
So the only difference is that if all calibration scales were equal to 1,
the driver startup would have failed.
* MC_HTE: unitialize with hover_thrust parameter
* MC_HTE: constrain hover thrust setter between 0.1 and 0.9
* MC_HTE: integrate with land detector and velocity controller
* MCHoverThrustEstimator: Always publish an estimate even when not fusing measurements. This is required as the land detector and the position controller need to receive a hover thrust value.
* MC_HTE: use altitude agl threshold to start the estimator
local_position.z is relative to the origin of the EKF while dist_bottom
is above ground
Co-authored-by: bresch <brescianimathieu@gmail.com>
Chip-select and SPI initialization uses the new config, whereas the drivers
still use the existing defines.
The configuration in board_config.h can be removed after all drivers are
updated.
- reduces amount of board configuration required
- removes the cyclic dependency between io_timers_t and timer_io_channels_t
Fixes a bug in the fmuk66-v3 config: the 2. timer has 3 channels associated
not 2.
Fixes a bug in the modelai config: the 2. timer has 4 channels associated.
- it does nothing useful
- increases boot time by 2 seconds on pixhawk 4 due to a poll timeout:
IST8310 on I2C bus 3 at 0x0e (bus: 100 KHz, max: 400 KHz)
WARN [ist8310] ERROR: TIMEOUT 2
- this is a new module for temperature compensation that consolidates the functionality previously handled in the sensors module (calculating runtime thermal corrections) and the events module (online thermal calibration)
- by collecting this functionality into a single module we can optionally disable it on systems where it's not used and save some flash (if disabled at build time) or memory (disabled at run time)
- instrumenting PX4 Matrix and Param methods is too burdensome
- partially restore px4_fmu-v5_stackcheck and holybro_durandal-v1_stackcheck to match default configs
Change PID to 0x4b:
Holybro obtained their own PID and VID but APM did not follow
the PX4 convention of makeing the board_id (0x8b) match the PID)
Incorporated the Upstream Bootloader state sequencing checking change.
Change the usb cout to send all chars in 1 write.
Durandal:Fix PLL settings
durandal-v1:Move I2C123, I2C4 to HSI.
Not liking using HSI but, F7 has, and in reality there is no
requerment for accuracy.
durandal-v1:board config set 400kHz on card probe
durandal-v1:Board SDMMC Clock Not greater then 25 mHz
durandal-v1:Fix PLL3 configuration typo and value
CI build config for holybro_durandal-v1
durandal-v1:Kconfig - add knob to ensure ARCH_MATH_H is kept
Upstream changes added ARCH_HAVE_MATH_H to protect from archs
without math.h from causing isses for users setting
CONFIG_ARCH_MATH_H and getting errors. PX4 provides a math.h
and we need CONFIG_ARCH_MATH_H set. So this Selects
ARCH_HAVE_MATH_H perserving CONFIG_ARCH_MATH_H a defconfig
Track master LED removal
durandal-v1: bmi055 -> bmi088
bmi088 is what the board uses
durandal-v1:add PX4IO support
durandal-v1 rc.board_sensors: start baro
durandal-v1: remove segway module
durandal:Run at 480 Mhz
durandal-v1: build thermal control module
durandal-v1: enable IMU thermal control by default
durandal-v1:Track upstream adc start moved to rc.board_sensors
durandal-v1:Track upstream mavlink start moved to rc.board_mavlink
and remove the px4_ prefix, except for px4_config.h.
command to update includes:
for k in app.h atomic.h cli.h console_buffer.h defines.h getopt.h i2c.h init.h log.h micro_hal.h module.h module_params.h param.h param_macros.h posix.h sem.h sem.hpp shmem.h shutdown.h tasks.h time.h workqueue.h; do for i in $(grep -rl 'include <px4_'$k src platforms boards); do sed -i 's/#include <px4_'$k'/#include <px4_platform_common\/'$k/ $i; done; done
for in $(grep -rl 'include <px4_config.h' src platforms boards); do sed -i 's/#include <px4_config.h/#include <px4_platform_common\/px4_config.h'/ $i; done
Transitional headers for submodules are added (px4_{defines,log,time}.h)
On more complicated setups it's still possible to exceed 32 tasks. For example fmu-v5 with mavlink on every telem (+ USB), external spi usage (pmw3901), gimbal (vmount), multiple i2c sensors, and camera feedback is 35 tasks (with top running). This is a fairly extreme case, so I'm only going to increase CONFIG_MAX_TASKS on newer F7 boards.
* adds a work_queue systemcmd that will bring a tree view of all active work queues and work items
* WorkQueues now track attached WorkItems and will shutdown when the last WorkItem is detached
-moved rc.mavlink to the boards optional rc additions (now it's called rc.board_mavlink) to handle board specific mavlink needs (mavlink over usb, ethernet, additional streams, etc.)
-mavlink module will be responsible to usb defaults, therefore less args are needed to be passed to mavlink module if one wants to use mavlink over usb.
-the way to check if connection is usb is by it's designated variable and not by config mode.
David Sidrane
Daniel Agar
Matthias Grob
斯东Stone
Beat Küng
Tanja Baumann
SalimTerryLi
mcsauder
Julien Lecoeur
Igor Mišić
garfieldG