Commit Graph

1746 Commits

Author SHA1 Message Date
Jason Short ab215838a6 ACM Nav_throttle- removed sign inversion 2012-11-16 17:38:57 -08:00
Robert Lefebvre 6c407e5770 Added Leonard to Contributor List. 2012-11-16 15:43:03 -05:00
rmackay9 3a4d122e32 ArduCopter: low baterry failsafe 2012-11-15 23:35:41 +09:00
rmackay9 414f9b9759 ArduCopter, APM_RC: failsafe if PPM encoder fails to update for 2 seconds 2012-11-15 23:35:36 +09:00
rmackay9 cd5da84698 ArduCopter: flight mode changes ignored while in throttle failsafe
reaction time to flight mode changes (when not in failsafe) reduced from 0.6 seconds to 0.1 seconds
2012-11-13 12:50:51 +09:00
rmackay9 6a2cca3610 ArduCopter, ArduPlane: rename ap variable in GCS_Mavlink.pde to resolve compiler warning re shadowing of variable 'ap'
Changed ArduPlane to keep function consistent with ArduCopter
2012-11-12 13:30:04 +09:00
rmackay9 dab975301b ArduCopter: remove some variables no longer required with introduction of AP_state 2012-11-12 12:41:25 +09:00
rmackay9 702dd1fb2e ArduCopter: remove last remanants of rate_d to resolve compiler warning of unused variables 2012-11-12 12:35:58 +09:00
Jason Short 1049381dbe ACM: Added fast descent with Bill P's equation for managed accerlation 2012-11-11 18:23:45 -08:00
Jason Short 27a41c294b ACM: attitude.pde - adjusted the FF of the alt hold algorithm, the old way was pretty crap. increased the output range of rate controller. 2012-11-11 18:22:54 -08:00
Jason Short e32491d749 ACM: Added a speed filter for throttle cruise, increased alt change rate for alt hold, increased the max climb_rate reporting 2012-11-11 18:17:33 -08:00
Jason Short a7d8ca8f52 ACM: Allow greater than 45° pitch and roll in Stab 2012-11-11 18:07:58 -08:00
Jason Short add51f110d ACM : Logging.pde formatting 2012-11-11 18:06:50 -08:00
Jason Short ee9ac7ab2c ACM : loging ApState at faster rate 2012-11-11 18:00:10 -08:00
Jason Short a6bda80064 ACM: Allow for user defined roll and pitch input max 2012-11-11 18:00:10 -08:00
Andrew Tridgell b556ebf8b2 MAVLink: update compass health in SYS_STATUS
this will make it easier to tell if a I2C error occurred in flight
2012-11-12 11:26:54 +11:00
rmackay9 eb25b917ad ArduCopter: renamed system bitmap to ap_system to resolve desktop compile issues 2012-11-11 22:42:10 +09:00
rmackay9 41c0cee292 ArduCopter: failsafe improvements
resolves momentary throttle drop to zero before failsafe engages
resolves motor cut after 30seconds if flying in stabilize without GPS (now switches to ALT_HOLD with target altitude zero)
disables motors if throttle was zero before failsafe event
2012-11-11 22:11:12 +09:00
rmackay9 95771692f0 ArduCopter: remove unnecessary debug print mesage from save_trim function 2012-11-10 23:10:29 +09:00
rmackay9 c8bc64be61 ArduCopter: fix APM2 build 2012-11-10 22:06:23 +09:00
Jason Short a7360af180 ACM formatting 2012-11-09 22:15:16 -08:00
Jason Short b10975baaf ACM : climb rate option using Bill P's equation 2012-11-09 22:15:16 -08:00
Jason Short f17c63062e ACM crosstrack min distance 2012-11-09 22:15:16 -08:00
Jason Short 6a2ba899cb ACM Logging Events 2012-11-09 22:15:16 -08:00
Jason Short 3539a6817f ACM Log, formatting 2012-11-09 22:15:16 -08:00
Jason Short 40a1f647f6 ACM : Setup, format 2012-11-09 22:15:16 -08:00
Jason Short 7fab9d940f ACM | removing old files 2012-11-09 22:15:16 -08:00
Jason Short 3e905ec750 Ap state updates 2012-11-09 22:15:15 -08:00
Jason Short 81b1ebd011 ACM: Added max RTL altitude 2012-11-09 22:15:15 -08:00
Jason Short c415830e81 ACM: added ap_state.pde 2012-11-09 22:15:15 -08:00
Jason Short d527d19635 ACM : Attitude : added nav param reset 2012-11-09 22:15:15 -08:00
Jason Short 9b295ca7cf ACM : Attitude.pde added ap bitfield for failsafe bit 2012-11-09 22:15:15 -08:00
Jason Short 9b16fdf182 ACM : Attitude.pde removed stabilize D 2012-11-09 22:15:15 -08:00
Jason Short f48db96156 ACM : Arducopter Added ap state bitfield, system bitfield 2012-11-09 22:15:15 -08:00
Jason Short 00b41a198d ACM: Arducopter - remove the stabilize D scheduling 2012-11-09 22:15:15 -08:00
Jason Short 99cf67fc9c ACM : formatting 2012-11-09 22:15:15 -08:00
rmackay9 fabc149f45 ArduCopter: remove unused functions wrap_360f, wrap_180f and wrap_PI 2012-11-08 15:20:08 +09:00
rmackay9 499bdc1385 ArduCopter: remove unused get_stabilize_rate_yaw 2012-11-07 23:28:25 +09:00
rmackay9 56f374fc7d AP_InertialNav: reanme AP_InertialNav and ThirdOrderCompFilter classes to resolve desktop build compiler errors 2012-11-07 22:24:00 +09:00
rmackay9 a0e69ddf27 ArduCopter: fixed HIL build caused by optical flow semaphore changes 2012-11-07 21:13:34 +09:00
rmackay9 07ecf8b40b ArduCopter: comment out InertialNav related Alt Hold and Loiter PID changes from APM_Config.h 2012-11-07 19:21:36 +09:00
rmackay9 af40201b14 ArduCopter: incorporate new version of inertial navigation
Moved several navigation functions from ArduCopter.pde to navigation.pde
2012-11-07 19:21:31 +09:00
rmackay9 e2b1cb7e8d AP_InertialSensor: changes after review with Tridge.
sanity checking added to accelerometer calibration routine.
user feedback is sent using gcs_send_text_fmt instead of Serial.printf.
moved ins parameters to new eeprom number to avoid conflicts with older parameters.
other small changes including renaming of functions and parameters.
2012-11-07 19:21:15 +09:00
rmackay9 0868917ff4 ArduCopter: move to use new INS library instead of IMU library 2012-11-07 19:21:09 +09:00
Andrew Tridgell 03974fa9db ACM: switch to GPS velocity numbers in GLOBAL_POSITION_INT
these numbers are much more useful than the redundent rotated ground
speed. They tell us exactly what the GPS is giving to AHRS
2012-11-05 15:23:41 +11:00
Jason Short 210148a432 ACM : Formatting 2012-10-28 12:12:38 -07:00
Jason Short 158c4f8d14 ACM : Formatting 2012-10-28 12:12:38 -07:00
Jason Short 0a68468610 ACM: Added simple mode bearing logging for bug hunting 2012-10-28 12:12:38 -07:00
Jason Short 9c40c11e7b ACM: Formatting 2012-10-27 14:13:46 -07:00
Jason Short 4eeaf4c984 ACM: Added notes, credit to decel code. added speed_min to calc. 2012-10-27 14:13:24 -07:00
Jason Short 1e35d3d534 ACM: config.h cleanup
Added LOG_ITERM default to enabled
2012-10-27 09:59:57 -07:00
rmackay9 2e6625b82c ArduCopter: change TOY_M throttle mode to THROTTLE_HOLD 2012-10-26 10:56:06 +09:00
rmackay9 e780bfd4c1 ArduCopter: remove some unhelpful constraints on nav_lat and nav_lon.
Increase other constraints from 3200 to 32000.  These constraints are there to ensure int32_t do not cause an overflow when added to an int16_t.
2012-10-24 22:04:35 +09:00
rmackay9 ab86eae860 ArduCopter: changed ACRO_ROLL_STABILIZE and ACRO_PITCH_STABILIZE to parameters
Changes on behalf of Leonard Hall
2012-10-23 21:30:50 +09:00
Andrew Tridgell 61f85d05cc ACM: save another 20 bytes 2012-10-22 18:59:51 +11:00
Andrew Tridgell e90d2138f2 ACM: saved some more memory for strings 2012-10-22 18:57:08 +11:00
rmackay9 7fb58fce87 ArduCopter: replace Serial.print with Serial.print_P to save memory.
Includes replacing flight_mode_strings with print_flight_mode function.
SendDebug macro replaced with direct Serial.print_P calls.
2012-10-22 16:45:24 +09:00
Jason Short fb9fe2c9a5 ACM : fix compiler warning on non returning function 2012-10-21 14:37:42 -07:00
Jason Short 97d3134ff0 ACM : Cast to int32_T
Don't think it really needs it, but I feel better with the cast.
2012-10-21 14:36:05 -07:00
Jason Short 96f0a32cd3 ACM Acceleration management
removed unused waypoint_radius var
removed slow_wp
updated speed management system to maintain a constant acceleration or deceleration of 1m/s
changed version to 2.8.1a
2012-10-21 14:32:39 -07:00
rmackay9 6a66fdace9 ArduCopter: updated firmware version to 2.8 2012-10-20 09:50:53 +09:00
rmackay9 4c7292e6ce ArduCopter: incremented eeprom format version to force users to accept the new defaults.
Particularly important is the roll-pitch I term move from the stabilize to rate controllers.
2012-10-19 16:14:51 +09:00
Pat Hickey 0dd0bd131a Update ArduCopter and ArduPlane dependencies on AP_Menu 2012-10-18 20:53:39 -07:00
Robert Lefebvre 9a20fe32fa Fixed that last commit
#define Stupid_Mistake
2012-10-18 16:50:42 -04:00
Robert Lefebvre 5f8f53ec0a Changed RLT Yaw Mode for TradHeli. Also a few comment cleanups. 2012-10-18 16:39:05 -04:00
rmackay9 d7c80fb025 ArduCopter: updated firmware version to 2.7.4-Zeta 2012-10-18 23:30:28 +09:00
rmackay9 3b631f1edd ArduCopter: integrated Leonard Hall's improved ACRO mode 2012-10-18 23:24:34 +09:00
rmackay9 e0727e6d31 ArduCopter: bug fix for telemetry not working on APM1.
SPI3 is also UART3.  On APM1 we use UART3 for telemetry and don't need SPI3.
2012-10-18 19:15:21 +09:00
rmackay9 9392c8cae2 ArduCopter: added spi_semaphore to stop conflicts between dataflash and optical flow sensor on APM1 2012-10-18 17:04:44 +09:00
rmackay9 0299e2b51e ArduCopter: removed deprecated mag offset routine.
Also removed commented-out block of code from navigation.pde.
2012-10-17 19:47:21 +09:00
rmackay9 f1fe5f303b ArduCopter: updated firmware version to 2.7.4-Epsilon 2012-10-17 19:27:11 +09:00
rmackay9 a4a2fad798 ArduCopter: more out-of-date commented out code removed 2012-10-17 19:25:14 +09:00
rmackay9 25b3acab8c ArduCopter: bug fix in earthframe->body frame translation.
Provided by Leonard Hall.

Also removed large unnecessary comments.
2012-10-17 19:15:25 +09:00
rmackay9 3a26606510 ArduCopter: reduced optical flow's I and IMAX terms 2012-10-17 17:47:43 +09:00
rmackay9 7228236db6 ArduCopter: updated firmware version to 2.7.4-Delta 2012-10-17 10:20:41 +09:00
rmackay9 7787bb4fd5 ArduCopter: bug fix for get_yaw_rate_stabilized_ef
Provided by Leonard Hall
2012-10-17 10:18:24 +09:00
Andrew Tridgell 33d9ae23ff battery: use set_pin() to allow pins to be changed at runtime 2012-10-16 17:20:49 +11:00
Robert Lefebvre 1e01a642bc Adding some comments to parameters. 2012-10-15 09:37:02 -04:00
rmackay9 025cc05cab ArduCopter: update version information ahead of testing 2012-10-15 18:15:38 +09:00
LeonardTHall 4203655646 New Yaw controller using rate feed forward and stabilize.
Signed-off-by: LeonardTHall <LeonardTHall@gmail.com>
2012-10-15 11:37:49 +09:00
rmackay9 ee41f3be6c ArduCopter: enable ACRO mode's AXIS_LOCK by default 2012-10-14 19:50:45 +09:00
rmackay9 254fff6acd ArduCopter: fixed acro mode
Changes included:
Removing earth frame roll_rate_trim, pitch_rate_trim and yaw_rate_trim.
Switch ACRO mode to use YAW_ACRO instead of YAW_HOLD.
Changed YAW_ACRO to use stabilize yaw when axis_enabled.
Reset ACRO roll, pitch and yaw targets to current attitude when first entering ACRO.
2012-10-14 17:47:46 +09:00
rmackay9 c201b3c35e ArduCopter: small comment fixes related to battery monitoring 2012-10-13 20:52:14 +09:00
rmackay9 71c773801a ArduCopter: added BATT_VOLT_PIN and BATT_CURR_PIN parameters to allow support for new 3DR IV battery voltage and current monitor 2012-10-13 18:40:46 +09:00
Robert Lefebvre 8e19e7d0b2 Added #define for Tilt_Compensation.
Also added some detail to WP_Speed_Max parameter.
2012-10-12 14:51:31 -04:00
Robert Lefebvre 446d8ee934 Added comment detail for Tilt_Comp Parameter.
Reduced parameter default value for TradHeli.
2012-10-11 13:17:39 -04:00
rmackay9 9052b4152b ArduCopter: remove unnecessary (probably slightly harmful) extra barometer read
The barometer reads including reading temperature was all moved to a timer but this extra read (originally to read the temperature) was probably forgotten.
2012-10-11 18:31:10 +09:00
rmackay9 b5c1e23549 ArduCopter: changed sin_pitch and sin_roll to faster equivalents 2012-10-11 17:54:42 +09:00
rmackay9 a5feda6b1f ArduCopter: set default rate roll and pitch I terms to 0.010, and rate yaw to 0.015
Updated after discussing with Marco
2012-10-11 17:25:01 +09:00
rmackay9 94d16d426f ArduCopter: move I terms from stabilize to rate controllers 2012-10-11 17:20:05 +09:00
rmackay9 be25e75d75 ArduCopter: freeze I terms if motor limits breached 2012-10-11 17:20:00 +09:00
Andrew Tridgell 2af5ff896d ACM-HIL: fixed optflow declaration 2012-10-11 11:51:25 +11:00
Pat Hickey 24dcbe1b0e ArduCopter GCS_MAVLink: COMMAND_LONG for arm/disarm motors
Date: Wed, 26 Sep 2012 15:56:43 -0700
Subject: ArduCopter arm/disarm command consensus
From: Pat Hickey
To: Michael Oborne
Cc: "Craig J. Elder", arducopter
<arducopter@googlegroups.com>,
    mavelous <mavelous@googlegroups.com>

    Michael,

    Per our discussion today,

    In a MAVLINK_MSG_ID_COMMAND_LONG
    A MAV_CMD of type MAV_CMD_COMPONENT_ARM_DISARM
    with component id MAV_COMP_ID_SYSTEM_CONTROL = 250,
    uses param index 1 to specify an arm/disarm motors event: 1 to arm,
    0 to disarm

    Thanks for working this out with me. Sorry to get it so completely
    wrong the first time around!

    Best
    Pat
2012-10-10 18:59:55 +08:00
Pat Hickey 74d5b1b841 ArduCopter: Provide AP_Semaphore instance for SPI3 bus on APM2. 2012-10-09 11:39:39 -07:00
rmackay9 04b50af6e1 ArduCopter: added message to console when entering ESC Calibration on startup 2012-10-09 12:31:05 +09:00
rmackay9 0050232ae2 ArduCopter: failsafe added to shutdown motors if mainloop fails 2012-10-09 12:30:17 +09:00
rmackay9 50e19dfd12 ArduCopter: APM_Config.h - make it ever so slightly easier to enable INERTIAL_NAV 2012-10-08 12:31:51 +09:00
rmackay9 9d5d9ce3fc ArduCopter: bug fix to ROI when no camera mount is specific 2012-10-08 12:31:10 +09:00
rmackay9 f88ca4b7e4 ArduCopter: bug fix in earth-frame to body-frame conversion for roll 2012-10-07 19:14:40 +09:00
rmackay9 ae447ad6b6 ArduCopter: fix heli build 2012-10-06 13:46:19 +09:00
rmackay9 ae05bc62f6 ArduCopter: added AP_Semaphore to list of includes 2012-10-06 12:41:58 +09:00
rmackay9 c2b9c695b4 ArduCopter: reduce Stabilize Yaw P term to 4.5 2012-10-03 14:19:49 +09:00
rmackay9 a35543bf96 ArduCopter: prioritise rate controllers, rate controller targets converted to body frame 2012-10-03 14:10:31 +09:00
rmackay9 770aa0b56b ArduCopter: BATT_PIN parameter added to allow you to select which pin is used for voltage and current measurements
To save a parameter, the current sensor pin is assumed to always be 1 higher than the voltage pin.
2012-10-02 22:16:19 +09:00
Michael Oborne 939ee1f4a9 AP,AC Add ability to override an altitude in any auto mode, on the current active target 2012-09-30 07:29:33 +08:00
rmackay9 fc4f4d76c9 ArduCopter: allow DMP to run in parallel with DCM
Parallel DMP can be enabled by #define SECONDARY_DMP_ENABLED in APM_Config.h
New DMP dataflash log type added to allow easy comparison with DCM
2012-09-30 00:25:40 +09:00
rmackay9 1cd4b08fac AP_AHRS: added scheduler parameter to init
Required by the AP_AHRS_MPU6000 class which needs to disable timed processes that could interfere with it's communication with the mpu6000
2012-09-29 13:51:21 +09:00
rmackay9 4bca609b9f AP_InertialSensor_MPU6000: replaced _cs_pin parameter with #define and saved 1 byte of memory
Updated ArduCopter, ArduPlane and example sketches in AP_InertialSensor, AP_IMU and AP_AHRS libraries because they no longer need to pass in cs_pin to the constructor
2012-09-28 19:21:59 +09:00
rmackay9 04c92240c4 ArduCopter: tiny formatting change in defines.h 2012-09-27 17:40:54 +09:00
rmackay9 fec3f3260e ArduCopter: bug fix to display ITERM enabled/disabled properly from cli
Also changed header for this message type to ITERM instead of just IT to make it more clear what it is
2012-09-27 17:40:30 +09:00
rmackay9 ebbf8dc6be ArduCopter: updated version to 2.7.4-Beta 2012-09-25 23:39:15 +09:00
rmackay9 08f203a991 ArduCopter: reduced Loiter Rate I to 0.04 (was 0.08) 2012-09-25 19:08:31 +09:00
rmackay9 15893e719a ArduCopter: increase default Loiter Rate P to 5.0 2012-09-25 12:19:44 +09:00
rmackay9 090a672636 ArduCopter: optical flow initialisation changes now that optical flow library automatically works on APM1, APM2 and APM2.5 2012-09-24 18:39:33 +09:00
rmackay9 12a1f3244b ArduCopter: alt hold bug fix - removed reset next_WP in init_home 2012-09-23 01:00:06 +09:00
rmackay9 5e6951d3f4 ArduCopter: position lead filters modified to use lag which varies by gps 2012-09-20 15:49:09 +09:00
rmackay9 69c29f5196 ArduCopter: allow PID logging of throttle. Make get_angle_boost actually use parameter passed in. 2012-09-18 23:19:23 +09:00
rmackay9 aaab3c08aa ArduCopter: added throttle curve (although disabled by default) for all multicopters 2012-09-18 23:05:08 +09:00
rmackay9 3b5b2eba6e ArduCopter: set fast gains while auto trim is being executed 2012-09-18 09:03:29 +09:00
Andrew Tridgell 14d19ac33d ACM: updates for new GPS detection
a GPS can now be attached after startup
2012-09-17 14:45:47 +10:00
rmackay9 d7a53e67ed ArduCopter: bug fix in Log_Read_Attitude. It was printing two uninitialised variables. 2012-09-17 13:44:29 +09:00
rmackay9 9965dd8b1a HIL: changes to fix HIL for ArduCopter after recent timing changes.
Changes include using AP_PeriodicProcess and calling imu.init even in HIL mode
2012-09-15 18:42:56 +09:00
rmackay9 94d4305cf3 ArduCopter: print firmware version of code instead of zero. 2012-09-13 21:49:11 +09:00
rmackay9 54d07f6d04 ArduCopter: removed INSTANT_PWM from ArduCopter and AP_Motors library 2012-09-13 21:31:13 +09:00
Jason Short e4ec96e12f ACM : better debugging text 2012-09-12 23:06:06 -07:00
Jason Short ecf7e0e8bf ACM l Prevent pre-mature finish of mission 2012-09-12 23:06:06 -07:00
Jason Short b56dc44e61 ACM : Fix enduf 2012-09-10 21:25:53 -07:00
Jason Short 24f80c632c ACM : forced setup_show to dump params during log dump for better analysis. 2012-09-10 20:52:30 -07:00
Jason Short 65dc4ccc6d ACM : Added centralized Iterm logging at a lower rate. Logs all iterms. 2012-09-10 20:26:48 -07:00
Jason Short 63aec7510e ACM Mavlink - fixed comparison of unsigned to signed int by casting to uint8_t 2012-09-10 20:22:57 -07:00
Jason Short 2fcc7d3b22 ACM : Params - formatting cleanup 2012-09-10 20:22:11 -07:00
Andrew Tridgell ea78121f1b ACM: use spare CPU cycles to read the magnetometer 2012-09-10 11:38:18 +09:00
rmackay9 7a0189fb2c ArduCopter: modified mainloop timing to be in sync with the arrival of new data from the IMU.
This reduces the maximum delay between when new sensor data arrives and when it is actually used by about 5ms.
2012-09-10 11:37:53 +09:00
rmackay9 4e85e545bf ArduCopter: added NUM_IMU_SAMPLES_FOR_XYZHZ definitions for MPU6000 and Oilpan to allow more syncing of the mainloop with the arrival of data from the IMU. 2012-09-10 11:37:48 +09:00
rmackay9 8f993cde2b ArduCopter: bug fix for ROI not working if user did not have a camera mount
Changed verify_nav_roi command to attempt to point at the target if our camera mount type is not pan_tilt nor pan_tilt_roll
2012-09-10 02:03:32 +09:00
Andrew Tridgell 1fecd135ef ACM: use compass.accumulate() in ArduCopter
this gives us a much less noisy magnetometer
2012-09-08 10:06:04 +10:00
Michael Oborne 1d0d45a95f Fix Approach Altitude min 2012-09-06 17:43:58 +08:00
Pat Hickey b52738662a APM_Config.h for ArduCopter/ArduPlane: better descr of APM2_BETA_HARDWARE 2012-09-05 15:36:57 -07:00
rmackay9 af2502c739 ArduCopter: upgraded firmware version to 2.7.3 2012-09-02 12:58:16 +09:00
rmackay9 3e6966c33d ArduCopter: fixes to allow AP_Mount to work on APM1 with original default channels and fix to reenable support for 3-axis gimbals on APM2.
Channels 5 to 11 changed to RC_Channel_aux.
Removed channel 9 because APM_RC doesn't support it in any case.
Updated EEPROM format version to 119 because of the change to RC_Channel_aux and because k_param_rc_11 moved to be after k_param_rc_10.
2012-09-02 12:51:23 +09:00
rmackay9 6c1bd815c1 ArduCopter: remove unnecessary references to CH_CAM_PITCH, CH_CAM_ROLL, CH_CAM_YAW 2012-09-02 12:47:27 +09:00
Craig Elder c83d1402fb Arducopter: Release 2.7.2 2012-08-31 19:18:10 -07:00
Andrew Tridgell 0b2cbbb677 ACM: added TELEM_DELAY to ArduCopter 2012-08-30 09:03:01 +10:00
Jason Short 0ab8b85a78 ACM Log.pde : whitespace clean up 2012-08-28 21:22:07 -07:00
Jason Short 91bc3705c1 ACM : revert back to the 2.6 climb rate calc
The current filter is outputting wild oscillations.
2012-08-28 21:22:07 -07:00
Craig Elder 3403e1b78d Arducopter: increased MAVLINK delay to 6s to reduce the chance of xBee bricking
Arduplane:  increased MAVLINK delay to 6s to reduce the chance of xBee bricking
Ardurover:  increased MAVLINK delay to 6s to reduce the chance of xBee bricking
2012-08-28 20:09:10 -07:00
rmackay9 4978e0c23f ArduCopter: increased Stabilize Roll and Pitch I term to 0.05 (was 0.01) based on feedback from Jason 2012-08-29 11:34:53 +09:00
Craig Elder 94957b3529 Arducopter: Preparing for 2.7.2 Release 2012-08-28 18:30:41 -07:00
Jason Short b757c7130d ACM : Logging updates 2012-08-28 15:40:08 -07:00
Jason Short 52def45ba0 ACM: Altitude Adjust 2012-08-28 15:40:08 -07:00