---------------------------------------------
- New improved fail-safe detection and handeling for single or multible signal loss and receiver malfuntion
- Improved LED status for APM 2.x
- Improved jitter performance (PPM output using nested interrupts)
-------------------------------------------------------------
ARDUPPM OPERATIONAL DESCRIPTION
-------------------------------------------------------------
APM 2.x LED STATUS:
-------------------
RX - OFF = No input signal detected
RX - SLOW TOGGLE = Input signal OK
RX - FAST TOGGLE = Invalid input signal(s) detected
RX - ON = Input signal(s) lost during flight and fail-safe activated
TX - OFF = PPM output disabled
TX - FAST TOGGLE = PPM output enabled
TX - SLOW TOGGLE = PPM pass-trough mode
SERVO INPUT (PWM) MODE:
-----------------------
- PPM output will not be enabled unless a input signal has been detected and verified
- Verified inputs are lost during operaton (lose servo wire or receiver malfunction):
+ The PPM output channel for the lost input will be set to the default fail-safe value
+ PPM throttle output (ch3) will be permanently set to fail-safe (900us)
- Lost channel signal is restored:
+ PPM output for the restored channel will be updated with the valid signal
+ PPM throttle output (ch3) will not be restored, and will continue to output fail-safe (900us)
PPM PASS-THROUGH MODE (signal pin 2&3 shorted):
-----------------------------------------------
- PPM output will not be enabled unless a input signal has been detected
- Active signal on input channel 1 has been detected:
+ Any input level changes will be passed directly to the PPM output (PPM pass-trough)
+ If no input level changes are detected withing 250ms:
+ PPM output is enabled and default fail-safe values for all eight channels transmitted
+ Input level change detected again, PPM fail-safe output is terminated and normal PPM pass-through operation is restored
fix airspeed error scale and min ground speed
modify mount options
add german lang
fix terminal baud rate issue
msi mod- single msi for x86 and x64 and all win os's
PPM polarity reversing was not working when changing the Output PPM pin level before timer 1 / output compare init. The compare generator initialization was reverting the pin to low level. Instead of that a force match compare is used after timer / compare generator init to set the PPM output to high level.
workaround for global_pos_int problem
fix 3dr iv sensor pin selection
add ability to disable dist to home on flight data screen
remove traces of crom.controls (mono)
fix arm/disarm button
fix hud battery text overlaying
tweak hud resize
tweak main switcher
fix quickview text scaleing
fix dist to mav.
added french translation thanks oliver
change tooltip time
add 3dr iv
add distance to home
dataflashlog update
Reworked the PPM decoder (i did forget the sync symbol pre-pulse)
Splitted pre-pulse and pulse width variable for better reliability and easier processing
Base algorithm added for channel count auto detection in the decoder himself.
Replaced the #define for PPM_CHx_CHANNELS by PPM_CHx_MAX_CHANNELS.
Channel count #define was not needed anymore thanks to the channel count auto detection.
Channel detection post processing to do.
Work in progress on a new Redundancy dual PPM sum mode for PPM encoder.
- New library PPM_Encoder_v3.h and new manual manual_v3.txt
- New format conversion capability between input and output PPM frame timings and channel count.
This will be experimental until heavily tested. The main goal is to allow the use of low cost satellite receivers in a high safety setup, and allow a new teacher / student RC mode without link between the two pilot transmitters.
remove some mavlink 0.9 code
add arm/disarm button. Not yet implemented AC and AP Side.
modify heli setup screen
modify failsafe screen
fix old firmware under mono
workaround mono crash.
modify planner wp storage
tweak log dl screen
add change alt button
modify tlog wp extractor, multiple extractions
speed up srtm reading
fix lang edit.
add arduino chip detect
fix apm2,2.5 dialog test
add write timeout. this will stop planner hangs on bad serial devices.
change quickview decimal places to 0.00
fix map clicking issue.
fix wind direction wrapping
add airspeed use
modify firmware screen from Marooned
major flightdata tab change.
add save/load polygon from file
add some error handling dialogs
add useritems to HUD
change hdop scale
fix posible follow me bug (, vs .)
fix posible friendly params bug (, vs .)
tweak flightdata log playback timming
fix gridv2 bug. if no waypoint had been done, the grid wold fail
tweak some mission upload potential issues
add ability to get param list from a log (from startup)
add ability to get the first wp list in a log, if wps where received in that log.
tweak video capture library timing
add est distance traveled
add est flight time
AP_Mount now updated
add expermental firmware options.
fix hud avi record framerate
add 2 direction wp circle
tweak gridv2
add tracker location option.
fix current sensor screen
add more right click flight planner options.
make some connecting error messages more detailed.
add partial microdrones protocol output
add experimental antenna tracker find
add new apparam eeprom reader
add ground alt display to hud
mod stats
modify guided mode alt selection.
test flight planner tab on flight data tab
move some functions to the right click menu
add xplanes data in/out setup to be automatic.
add better mission upload handeling.
these were moved to the main sketches to allow for compile time
selection of MAVLink 0.9 vs 1.0. We no longer support 0.9, so we can
move it back, which simplifies some test sketches
add enable/disable to mavlinkcheckbox
modify my button to curved
add delay to progress reporter dialog. to ensure correct parent
Fix Mount screen for AP
Fix Hardware screen Text
display roi difrently
modify HIL/Quad Hil
update dataflashlog format (thanks randy)
update mavcmd format for roi
Convert to IActivate, IDeactivate scheme, thanks andrew
add support for rfcomm* interfaces on linux
fix guage off screen draw mono issue.
remove use of BackStageViewContentPanel
andrews spacer changes - not using dues to screen space issue
change configpanel constructor to load xml directly
remove IMavlink Interface
fix hsi off screen draw issue on mono
modify hud to use sprite fonts, instead of drawing via GDI+
modify progress reporter to use a 10hz timer to update screen, using invoke/begininvoke fails on mono at 50hz (over 100ms per call).
fix targetalt and target airspeed jumping issue.
lots of cleanup on tab switching, ie stoping timers/other
3dr radio status led update
update ardurover car icon
speedup georef image screen. tested on over 1000 images.
Modify BackStage View - will change again soon
modify target alt calc
change order on param lists
remove old firmware selection dialog
add hil mod flag to hil connect
implement main switcher - will change again soon
change some invokes to async, to prevent other threads slowing.
fix mavlink log graphing error
modify help text
general mono for mac fixs - still combating https://bugzilla.xamarin.com/show_bug.cgi?id=3124
add toy Mode
fix some mono issues
fix opengl hud issue
change config font size
modify mylabel for mono
modify default telem rates
add extra sonar option
remove 0 home alt check
fix terminal hang issue
remove application idle call, causes 100% cpu on mono
update gimbal icons
modify graph line thinkness
autotest: unit testing for jenkins
- parameterized unit testing
- modular python test modules
- test groups by directory
- select tests individual or by group
- skip tests individually or by group
arducopter.py: parameterized several functions to allow throttle settings and timeouts
test modules: extracted and copied 8 tests from Tridge's autotest into modules
junit.xml: xml template for unit test reporting to jenkins
fix config panel value change detection
add loiter_ to AC config screen
Add praram name to Friendly param, and exception ignoring.
fix param file note line
intergrate andrews gimbal config.
fix any possible log appending issues
remove old cli planner on connect
modify speech to not crash on windows mono
Fix Issue 668 - typo
Fix issue 666 - now defaults to mav 1.0 planner
Fix Issue 665 - mavlink 1.0 is now default
Fix Issue 663 - increase timeout from 6 seconds to 12 seconds
Fix Issue 662 - now reads sat count for mav 1.0
Partial Issue 654 - added current to status, hud still wip
Fix Issue 648 - add validation to value
Fix Issue 638 - add delay
Fix Issue 636 - check for version.txt in app directory
Fix config panel null bug
Add more Ardurover config options
Add Exceptions handling to video format selection
Add FORMAT_VERSION to param file ignore list
Fix NOTE param file line
Add APMRover hidden firmware upload (control-R) on firmware screen.
fix possible speach engine exception
add dataflashlog for apmrover
add popouts in config/setup
add more text to hud heading nw,ne,sw,se
add 5 m filter to antenna tracker
add refresh param buttons
remove the word old, as people still want it.
modify telem playback interface with slider bars
add posible fix to bad grid spacing
move mavlink code.
work on opengltest
fix last missing param
fix com port selection on connecting to bad comport
add convert to csv. entire log
add log caching to image georef. for tlog and logs
add srtm data caching
Modify Hud center
add 3dr snr's and snr based distance estimate
display current frame type
fix disapearing window
add base xml level to param xml (xml standard)
add georef kml refrence
this includes adams new dynamic params
implement new arducopter pid tuning screen
included old for crossover.
add map rotation - follow plane
modify setup screen to show diffrent things based on ap software