rmackay9
677b38a48e
ArduCopter: first implementation of surface tracking using sonar
...
Note: not yet enabled as part of any flight mode
2013-01-02 09:55:37 +11:00
rmackay9
92e271e517
AP_InertialNav: increase baro delay to 0.5 sec (was 0.2sec) to allow slower baro updates on APM1
2013-01-02 09:55:37 +11:00
rmackay9
d400e5040b
ArduCopter: turn on INERTIAL_NAV_Z in the config.h file so that it takes effect when built for the mission planner
2013-01-02 09:55:37 +11:00
rmackay9
daac540e08
ArduCopter: get_throttle_althold - add check to avoid divide by zero
2013-01-02 09:55:37 +11:00
rmackay9
0decd870dc
ArduCopter: inertial nav - only initialise horizontal position when home is initialised
2013-01-02 09:55:37 +11:00
rmackay9
4c14010029
ArduCopter: update release notes for 2.9-rc1
2013-01-02 09:55:37 +11:00
rmackay9
576af6d487
ArduCopter: bug fix to althold desired rate calculation. Fix from Jonathan.
2013-01-02 09:55:37 +11:00
rmackay9
02bf3ea027
ArduCopter: Battery failsafe triggers RTL only if we are more than 15m from home, otherwise it performs a LAND
2013-01-02 09:55:37 +11:00
rmackay9
ff40fa6aab
ArduCopter: alt hold bug fix - should use 2x linear distance when calculating the desired rate
...
Bug fix from Leonard.
2013-01-02 09:55:37 +11:00
rmackay9
68b62abd38
ArduCopter with the new Camera and Relay classes for APM1 and APM2.
...
All changes by Sandro Benigno
2013-01-02 09:55:37 +11:00
rmackay9
393c893cdb
ArduCopter: bug fix (attempt #2 ) for accel based throttle controller
...
Thanks to Jonathan for this.
2013-01-02 09:25:58 +11:00
rmackay9
e583ade62d
ArduCopter: bug fix to accel based throttle controller (was using m/s instead of cm/s)
2013-01-02 09:24:31 +11:00
rmackay9
e77b54c7dc
ArduCopter: bug fix to GUIDED mode. Now checks that desired altitude was reached before deciding the waypoint is complete.
2013-01-02 09:24:31 +11:00
rmackay9
e850ab7ccd
ArduCopter: add AUTO_VELZ_MIN, AUTO_VELZ_MAX and PILOT_VELZ_MAX to allow better control of climb/descent rate in auto and manual throttle modes
2013-01-02 09:24:31 +11:00
Craig@3DR
0ed25cf719
Global change all references from
...
GPS_PROTOCOL_MTK16
to
GPS_PROTOCOL_MTK19
2013-01-02 09:24:31 +11:00
rmackay9
5526ca204c
ArduCopter: on throttle failsafe, only initiate RTL if we are at least 15m from home
2013-01-02 09:22:51 +11:00
rmackay9
466097b383
ArduCopter: use inertial nav for current altitude and climb rate
2013-01-02 09:22:51 +11:00
rmackay9
5ba363b007
ArduCopter: move gcs_check function (which sends to ground station) to run when 50hz loop is not running
...
Also removed redundant heartbeat message
2013-01-02 09:21:35 +11:00
rmackay9
331a73c4ac
ArduCopter: remove duplicate (?) send of MSG_EXTENDED_STATUS1
2013-01-02 09:20:08 +11:00
rmackay9
6baddf4aee
ArduCopter: remove unused variable last_5hz
2013-01-02 09:20:08 +11:00
rmackay9
1f5fdcdaa8
ArduCopter: remove unnecessary "Initialising APM message..."
2013-01-02 09:20:08 +11:00
Jason Short
8b62c4630b
ACM: Restore Multi-mode support
2013-01-02 09:20:08 +11:00
rmackay9
bd0e018ca0
ArduCopter: restore auto-trim method but now use AHRS.add_trim
2013-01-02 09:20:08 +11:00
Craig@3DR
e350bfbba8
Removed 2 more degree symbols from comments
2013-01-02 09:20:08 +11:00
rmackay9
b786cf40f7
ArduCopter: change GPS dataflash message to output unfiltered gps lat and lon
2013-01-02 09:19:39 +11:00
rmackay9
d3cbf733ba
ArduCopter: ensure RTL performs a land if a failsafe has been triggered
2013-01-02 09:19:39 +11:00
Robert Lefebvre
6e64b1b357
ACM: Precision Loiter RePositioning code.
...
Protected behind a #define
2013-01-02 09:19:39 +11:00
rmackay9
0fa6fdf407
ArduCopter: remove unused wait_for_yes function
2013-01-02 09:19:39 +11:00
rmackay9
e6519330f4
ArduCopter: remove unused rc_override variables to save 21 bytes
2013-01-02 09:19:17 +11:00
rmackay9
396024e802
ArduCopter: move scaleLongUp and scaleLongDown initialisation to init_home
2013-01-02 09:19:17 +11:00
rmackay9
7a5e4b8549
ArduCopter: stop unnecessary updates of target altitude and knock-on effect of too many EV message in dataflash log
2013-01-02 09:19:17 +11:00
rmackay9
1b5ff6aac6
ArduCopter: restore initial climb to RTL
2013-01-02 09:19:17 +11:00
rmackay9
52802cb29e
ArduCopter: limit output throttle to 800 only for TRI which does not have the new stability patch
2013-01-02 09:19:17 +11:00
rmackay9
34e18ae12a
ArduCopter: increase accel based throttle PIDs and add D term to rate based throttle
2013-01-02 09:19:17 +11:00
rmackay9
ac8af9a53f
ArduCopter: Leonard Hall's changes to alt hold including adding low pass filter to climb rate
...
get_throttle_rate_stabilized changed to simply update the target altitude instead of talking directly to the rate controller.
get_throttle_althold changed to use sqrt of distance when calculating the desired rate towards the target altitude.
added reset of accel based throttle PID's I term.
unrelated small bug fix from Randy to allow CH6 tuning of throttle rate D term.
2013-01-02 09:19:17 +11:00
rmackay9
f4c50353b9
ArduCopter: allow tuning of the Throttle Rate D term
2013-01-02 09:16:48 +11:00
Robert Lefebvre
9605bd8ee1
ACM: Trying to set a default MPU6K filter rate of 10Hz for TradHeli. Doesn't Work.
2013-01-02 09:14:55 +11:00
rmackay9
d926360e81
ArduCopter: move gcs updates to run only when there are 4ms of spare time before the next 100hz iteration starts
2013-01-02 09:14:31 +11:00
rmackay9
881dae1e27
ArduCopter: remove throttle limit of 800 for quads, hexas and octacopters
...
Note: Y6 and OctaQuads still have the 800 limit because they do not have the latest stability patch
2013-01-02 09:13:42 +11:00
rmackay9
6da68c53a5
ArduCopter: bug fix so AP_Limits does not use up memory if it is disabled
2013-01-02 09:13:42 +11:00
rmackay9
d8e3d5c10c
ArduCopter: allow RTL's yaw mode to be overridden with a #define in APM_Config.h
2013-01-02 09:12:40 +11:00
rmackay9
5633164fa0
ArduCopter: bug fix for compass.accumulate check in main loop (millis vs micros issue)
2013-01-02 09:12:40 +11:00
rmackay9
50d46898fb
ArduCopter: allow GUIDED mode roll-pitch, yaw and throttle control modes to be overridden
2013-01-02 09:12:17 +11:00
rmackay9
ddc578fd18
ArduCopter: restore YAW to default AUTO_YAW mode instead of YAW_LOOK_AT_NEXT_WP mode
2013-01-02 09:12:17 +11:00
rmackay9
0ab82f8c4e
ArduCopter: clear ahrs roll and pitch trims after an accel level command
2013-01-02 09:12:17 +11:00
rmackay9
7ea34d4fb7
ArduCopter: updated accel based throttle to use ahrs's get_accel_ef method
...
Also removed slow low pass filter meant to correct for accelerometer calibration. This is no longer required now that we have the improved calibration method.
2013-01-02 09:11:25 +11:00
rmackay9
4dfe3a2d73
ArduCopter: remove weird character from navigation.pde
2013-01-02 09:11:25 +11:00
Robert Lefebvre
ab95f04a91
ACM: TradHeli
...
Change name of attitude rate feed-forward parameters.
2013-01-02 09:10:40 +11:00
rmackay9
8e032b89ee
ArduCopter: create 2.9 branch and update firmware version
2013-01-02 09:10:40 +11:00
Andrew Tridgell
cf8e648558
CLI: fixed accel setup
...
disable mavlink callback in CLI
2012-12-24 08:51:33 +11:00
Andrew Tridgell
9931009db2
Math: use pythagorous2() in some more places
2012-12-20 15:16:18 +11:00
Andrew Tridgell
78d98023f4
Copter: remove use of 'byte'
2012-12-20 14:58:07 +11:00
Pat Hickey
1878290510
ArduCopter: fixes for AP_InertialSenor_UserInteract
2012-12-20 14:53:23 +11:00
Andrew Tridgell
3c0440b0b4
Math: use common degrees() and radians() functions
2012-12-20 14:53:22 +11:00
Andrew Tridgell
06357c40f2
Copter: use new functions
2012-12-20 14:53:22 +11:00
Pat Hickey
2ad4fed8cd
Rover/Copter/Plane: change from vsnprintf to vsnprintf_P
2012-12-20 14:52:38 +11:00
Pat Hickey
54b98c0a7c
ArduPlane: use hal's vsnprintf
2012-12-20 14:52:37 +11:00
Andrew Tridgell
a02f723f3a
Copter: fixed HIL builds
2012-12-20 14:52:37 +11:00
Andrew Tridgell
2e8e84ba8b
Copter: switch to using targets.mk
2012-12-20 14:52:36 +11:00
Pat Hickey
eb530b86e8
move Arduino.mk to /mk/Arduino.mk
2012-12-20 14:52:35 +11:00
Andrew Tridgell
9e986801c9
Copter: fixed SITL for ArduCopter
2012-12-20 14:52:34 +11:00
Andrew Tridgell
08b1c2d590
Copter: fixed GPS init
2012-12-20 14:52:33 +11:00
Pat Hickey
9a28ed2df6
ArduCopter: refactor Makefile targets in terms of Arduino.mk targets
2012-12-20 14:52:31 +11:00
Andrew Tridgell
7d27e420ae
AP_HAL: remove unnecessary Arduino.h includes
2012-12-20 14:52:30 +11:00
Pat Hickey
22ac39a4ef
ArduCopter: disable and remove InertialNav defines from APM_Config
...
* We're not going to have the RAM available to support those in general release
2012-12-20 14:52:29 +11:00
Pat Hickey
d5d97be837
ArduCopter: add param loader properly implement parameters
...
* thanks tridge!
2012-12-20 14:52:29 +11:00
Pat Hickey
5e63491994
ArduCopter: fix issues with HAL/HIL mixup and baro/compass instances
2012-12-20 14:52:29 +11:00
Pat Hickey
21d0da84a6
ArduCopter: temporarily disable AP_Param::setup_sketch_results
...
* rebased away tridge's AP_Param changes as they seemed possibly buggy?
2012-12-20 14:52:29 +11:00
Pat Hickey
a0151aa66c
ArduCopter: fix cliSerial null ptr, do AP_Param::setup_sketch_defaults
...
* plus make SITL DataFlash available.
2012-12-20 14:52:29 +11:00
Pat Hickey
1e48d0fc69
Makefile Targets rewritten to use per-target extension style
2012-12-20 14:52:29 +11:00
Pat Hickey
524e52f449
ArduCopter: changed makefile to inherit environments properly
2012-12-20 14:52:29 +11:00
Pat Hickey
d93d932831
ArduCopter: defines fixes
...
Conflicts:
libraries/AP_Common/Arduino.mk
2012-12-20 14:52:28 +11:00
Pat Hickey
2aa4657315
ArduCopter: changes to use CONFIG_HIL_BOARD
2012-12-20 14:52:28 +11:00
Pat Hickey
ade7099d75
ArduCopter: add AP_HAL_MAIN
2012-12-20 14:52:28 +11:00
Pat Hickey
5bd7046a95
ArduCopter: sketch cpp builds!
2012-12-20 14:52:28 +11:00
Pat Hickey
8b49208771
ArduCopter: some fixes
2012-12-20 14:52:28 +11:00
Pat Hickey
13c044ab3e
ArduCopter: fixes to radio.pde
2012-12-20 14:52:28 +11:00
Pat Hickey
7af03127f6
ArduCopter: more work
2012-12-20 14:52:28 +11:00
Pat Hickey
b90889dd11
ArduCopter: add ArduPlane's compat.h & compat.pde
2012-12-20 14:52:28 +11:00
Pat Hickey
70f4739522
ArduCopter: more fixes
2012-12-20 14:52:28 +11:00
Pat Hickey
4b84e99f85
remove dumb user hooks comments
2012-12-20 14:52:28 +11:00
Pat Hickey
901c692ee3
arducopter: type fix
2012-12-20 14:52:28 +11:00
Pat Hickey
f281d9265e
ArduCopter: reworked sonar analog source creation
2012-12-20 14:52:28 +11:00
Pat Hickey
d9e0bbbbab
ArduCopter: first pass at AP_HAL porting
...
* changed all the byte types to uint8_t
* fixed up much of the serial stuff
2012-12-20 14:52:27 +11:00
Pat Hickey
b7a7eceef8
ArduCopter: add nocore.inoflag and Arduino.h
2012-12-20 14:51:40 +11:00
Pat Hickey
ada10f6eb2
ArduCopter: change comment references to AP_Var to AP_Param
...
* jsut to clean up the grep for "AP_Var"
2012-12-20 14:51:31 +11:00
Pat Hickey
a4f1f6a5db
AP_Progmem: fix dependencies for all sketches touched by AP_HAL_AVR
2012-12-20 14:51:28 +11:00
Pat Hickey
3f1d9d7f69
AP_Param: #include <AP_Param.h> fixups for libraries & sketches
...
* I mostly went through with grep and added an #include <AP_Param.h> below
every #include <AP_Common.h>. Not all of these example sketches might
strictly need AP_Param.
2012-12-20 14:51:19 +11:00
Jason Short
0419dc8dfd
ACM: Simplified control mode code
2012-12-14 13:30:48 -08:00
Jason Short
19ae5c30eb
ACM : Formatting
2012-12-13 20:12:39 -08:00
rmackay9
52177c63f7
ArduCopter: only attempt to change settings of optical flow sensor if it has been successfully initialised
2012-12-11 00:14:29 +09:00
rmackay9
af77425636
ArduCopter: fix Failed to Init Optflow message at startup
2012-12-11 00:09:45 +09:00
rmackay9
2f748f8382
ArduCopter: renamed BATT_FAILSAFE to FS_BATT_ENABLE
2012-12-10 23:47:14 +09:00
rmackay9
d31efebd44
ArduCopter: rename throttle failsafe parameters.
...
Switch to LAND flight mode if throttle failsafe triggers and we do not have a GPS.
THR_FAILSAFE renamed to FS_THR_ENABLE.
THR_FS_VALUE renamed to FS_THR_VALUE.
THR_FS_ACTION removed (action is now controlled by setting FS_THR parameter).
2012-12-10 23:38:43 +09:00
rmackay9
2f1b2b70e6
ArduCopter: added ACRO_TRAINER parameter to allow enabling/disabling the acro training function which will bring the roll back to within +- 45 degrees
2012-12-10 22:27:46 +09:00
rmackay9
dadad8677e
ArduCopter: added descriptions for most parameters that did not have them
...
Renamed loiter_radius to circle_radius to better reflect it's purpose.
Removed some unused parameters including WP_MODE, WP_MUST_INDEX, LOG_LASTFILE, AXIS_P
2012-12-10 21:45:57 +09:00
rmackay9
f522ef078e
ArduCopter: remove unused functions do_target_yaw, do_loiter_at_location, get_altitude_error and clear_new_altitude
2012-12-10 17:30:50 +09:00
rmackay9
047f848cc7
ArduCopter: remove ThirdOrderCompFilter from list of includes
2012-12-10 09:14:44 +09:00
rmackay9
154e3c33f7
ArduCopter, AP_InertialNav: consolidated ThirdOrderComplementaryFilter into AP_InertialNav to save about 200bytes of RAM
2012-12-10 00:43:11 +09:00
rmackay9
cfe2507c0b
ArduCopter: reduce Rate Roll/Pitch P to 0.150 (was 0.175) and increase I to 0.1 (was 0.01)
2012-12-09 18:08:45 +09:00
rmackay9
56ceb230cb
ArduCopter: add YAW_OVR_BEHAVE to allow control of when autopilot takes back control of yaw after pilot overrides it during a mission
2012-12-09 18:04:31 +09:00
rmackay9
0f7bb79d89
ArduCopter: add comments to tuning parameters.
...
Use RC_CHANNEL types as defined by RC_Channel library.
Remove unused definitions.
2012-12-09 16:44:42 +09:00
rmackay9
9a05d3bd36
ArduCopter: add comments at the top of many navigation functions
2012-12-09 15:50:50 +09:00
rmackay9
8c2423f618
ArduCopter: code clean-up. Changed update_nav_wp to use a switch statement and relocated to navigation.pde
2012-12-09 15:24:19 +09:00
rmackay9
b36eb406d4
ArduCopter: allow alt hold to be engaged with alt < 1m because sometimes we get baro drift.
...
Also initialisation of target altitude is done in set_throttle_mode function.
2012-12-09 14:48:01 +09:00
rmackay9
b4e5176e2a
ArduCopter, AP_InertialSensor: restore mpu6k sample rate to 200hz but keep default filtering at 42hz.
2012-12-09 14:27:33 +09:00
Robert Lefebvre
aa4d4f8c24
ACM: Adding Pre-Compiler Define for Stabilize Throttle Mode.
2012-12-08 20:41:05 -05:00
Robert Lefebvre
0eb57bf93d
ACM: TradHeli
...
Fix to make update_throttle_cruise work with stab_throttle scaling.
2012-12-08 15:12:39 -05:00
Robert Lefebvre
1b97a92098
ACM: Code Cleanup
2012-12-08 14:49:38 -05:00
rmackay9
f98a807d36
ArduCopter: remove debug related to yaw mode used for alt hold
2012-12-08 14:24:50 +09:00
rmackay9
9dd978576b
ArduCopter: auto yaw changes to allow pilot override of yaw during missions
...
Added set_yaw_mode to better control of yaw controller changes and variable initialisation.
Replaced AUTO_YAW mode with separate yaw controllers YAW_LOOK_AT_NEXT_WP, YAW_LOOK_AT_LOCATION, YAW_LOOK_AT_HEADING.
Pilot manual override of yaw causes yaw to change to YAW_HOLD (i.e. manual yaw) until next waypoint is reached.
Added get_yaw_slew function to control how quickly autopilot turns copter
Changed YAW_LOOK_AHEAD to use GPS heading and moved to new get_look_ahead_yaw function in Attitude.pde
Renamed variables: target_bearing->wp_bearing, original_target_bearing->original_wp_bearing.
Removed auto_yaw_tracking and auto_yaw variables and update_auto_yaw function as they are no longer needed.
Simplified MAV_CMD_CONDITION_YAW handling (do_yaw). We lose ability to control direction of turn and ability to do long panorama shots but it now works between waypoints and save 20bytes.
2012-12-08 14:23:32 +09:00
rmackay9
85c8bdce15
ArduCopter: removed unused and out-of-date #defines from APM_Config.h
2012-12-08 13:38:39 +09:00
rmackay9
68ca123224
ArduCopter: remove some unused #defines
2012-12-07 15:17:35 +09:00
rmackay9
99b32a39c4
ArduCopter: InertialNav time constant CH6 tuning changed to only update enabled axis
2012-12-07 13:01:40 +09:00
rmackay9
cca9f9dbce
ArduCopter: do_set_servo fix to resolve -1 being assigned to uint8_t
2012-12-07 12:58:44 +09:00
rmackay9
3a90fc77f9
ArduCopter: add dataflash logging of camera events
2012-12-07 00:57:08 +09:00
rmackay9
d74cf54b5d
ArduCopter: allow triggering of camera from a mission
2012-12-06 23:48:30 +09:00
rmackay9
d3de77f74c
ArduCopter: fix do_set_servo so that it works again
2012-12-06 20:18:33 +09:00
rmackay9
653535b9a1
ArduCopter: added CH7 option to trigger camera
...
Restructured reading of channel 7 into a switch statement.
2012-12-06 17:47:01 +09:00
rmackay9
4ca27defb3
ArduCopter: update comments related to CH7 switch options
2012-12-06 17:40:36 +09:00
rmackay9
75401756f2
ArduCopter: maintain loiter control even below 1m while landing
2012-12-06 12:40:53 +09:00
rmackay9
2dd4694eef
ArduCopter: adjusted pid_throttle_accel dt to 0.01 (100hz)
2012-12-06 10:32:12 +09:00
rmackay9
269e02ee93
ArduCopter: bug fix - initialise inertial nav
2012-12-06 10:32:07 +09:00
rmackay9
8d682b9812
ArduCopter: disable INERTIAL_NAV_XY by default
2012-12-06 10:32:02 +09:00
rmackay9
39d524212f
ArduCopter: allow accel based throttle controller to be enabled/disabled with the new THR_ACC_ENABLE parameter.
...
When disabled the original velocity based throttle controller is used.
2012-12-06 10:31:57 +09:00
rmackay9
a5bb54e36e
ArduCopter: RTL clean-up and slightly improved landing sensor
...
Consolidated RTL state to be captured by rtl_state variable.
Combined update_RTL_Nav and verify_RTL functions which performed the same function but one was for missions, the other for the RTL flight mode.
Renamed some RTL parameters and global variables to have RTL at the front.
Landing detector now checks accel-throttle's I term and/or a very low throttle value
2012-12-06 10:31:52 +09:00
rmackay9
6da07ef1d2
ArduCopter: increase CONTROL_SWITCH_COUNTER so that flight mode switch must be changed for at least 1/10th of a second
2012-12-06 10:31:46 +09:00
rmackay9
072ffec493
ArduCopter: allow INERTIAL_NAV to be enabled separately for horizontal and vertical position
2012-12-06 10:31:41 +09:00
rmackay9
aa5e7e63a0
ArduCopter: switch on INS in APM_Config.h (i.e. on by default for users uploading through Arduino IDE)
2012-12-06 10:31:36 +09:00
rmackay9
bdb47c449a
ArduCopter: pass linear altitude error to throttle rate controllers.
...
Previously the requested rate used the square root of the altitude error.
Scale pilot's desired vertical rate and acceleration based on ACCELERATION_MAX_Z and VELOCITY_MAX_Z #defines
2012-12-06 10:31:31 +09:00
rmackay9
d7f76ebd87
ArduCopter: add tuning of throttle rate controller's I term (THROTTLE_KI)
2012-12-06 10:31:25 +09:00
rmackay9
7b4ed2d227
ArduCopter: restored landing detector to landing throttle mode.
...
Added LAND_SPEED parameter to control the rate of descent for the last 10m of a landing.
Added CH6 tuning for accel based throttle controller.
2012-12-06 10:31:20 +09:00
rmackay9
560bb1d738
ArduCopter: removed unused AUTO_THROTTLE_HOLD #define
2012-12-06 10:31:15 +09:00
rmackay9
7035529953
ArduCopter: remove unused get_desired_climb_rate function
2012-12-06 10:31:09 +09:00
rmackay9
a94826f182
ArduCopter: add set_throttle_mode to better control initialisation of variables
2012-12-06 10:31:04 +09:00
rmackay9
1036b35128
ArduCopter: added back in angle boost and recombined for heli and multicopter
2012-12-06 10:30:55 +09:00
rmackay9
3cbef57c64
ArduCopter: first merge of leonard's accel based altitude controller plus other changes from Randy
...
Changes include:
New low-level get_throttle_accel function takes target acceleration and compares vs earth-frame Z accelerometer values to produce output to motors.
Higher level throttle controllers modified to call new get_throttle_accel controller
Throttle_rate_stabilized controller added which maintains a desired climb/descent rate
Throttle_land controller added - descends using normal auto throttle controller to 10m then descends at 50cm/s
Multiple throttle modes added including landing mode
Land flight mode no longer needs GPS
Throttle cruise maintenance moved to update_throttle_cruise function
2012-12-06 10:30:49 +09:00
Robert Lefebvre
8c18a60766
ACM: Small fix to Yaw Look Ahead
2012-12-04 14:50:14 -05:00
Robert Lefebvre
1d589c0b7d
ACM: TradHeli
...
Fixes for Attitude rate controllers.
2012-12-04 14:42:04 -05:00
Robert Lefebvre
5723021be1
ACM: TradHeli
...
Creating Rate Feed-Forward Parameters
2012-12-04 13:47:38 -05:00
Robert Lefebvre
3e65dd3ded
ACM: TradHeli APM_Config.h changes
2012-12-04 13:32:40 -05:00
Robert Lefebvre
315a7e8000
ACM: Yaw Look Ahead Changes
2012-12-04 13:26:41 -05:00
Robert Lefebvre
9130045298
ACM: Code Cleanup
2012-11-30 17:05:12 -05:00
rmackay9
8141f0b600
ArduCopter: bug fix - increase mpu6k sample rate to 100hz
2012-11-30 23:49:18 +09:00
Andrew Tridgell
6fbf5ec8f2
Copter: update ArduCopter for new ins interface
2012-11-30 07:15:18 +11:00
Michael Oborne
68aa5e4682
AC add ability to start new accel_scale via mavlink
2012-11-28 21:38:58 +08:00
Andrew Tridgell
2949d58b71
Copter: re-enable sending of GLOBAL_POSITION_INT message
...
this gives important raw GPS velocity information, plus relative and
absolute height
2012-11-28 11:26:19 +11:00
Robert Lefebvre
07d7d90882
ACM: TradHeli
...
Bringing in Low Pass Filter for Rate Controllers
2012-11-26 21:51:23 -05:00
Robert Lefebvre
6b8c39dd10
ACM: Creating Yaw_Look_Ahead yaw mode.
...
This function is not fully tested yet.
2012-11-26 21:37:13 -05:00
Robert Lefebvre
3f0e8dd358
ACM: TradHeli
...
Bringing in Low Pas Filter
Commented out because it does not build.
Needs updates to Low Pass Filter Lib
2012-11-26 21:21:12 -05:00
