Having "BIT" in the name gives the impression we are using the macro is
the bit position; however they have the values for those actions, not
the bit position. Rename BIT to VAL to be less confusing.
This is the equivalent of sleep and wait for the conversion time,
after had triggered a new sample request. However it also has the added
benefits of sharing a thread with other sensors on the same bus.
Now we don't read the status register anymore since we have a guaranteed
wait time.
- Make sure device is reset while initializing.
- Give better names to register macros
- Average X, Y and Z by 16: sensor is internally running at 200 sps
(theoretical, ~160 pratical). The wait time is ~6msec averaging
by 16. We do 10msec.
- Inline code that needs to take and release the lock in init()
function, just like other drivers
- Minor changes to coding style and renames to be similar to other
drivers
This compass has been proved to work better on Navio boards. Users also
don't like high offsets (even though, they don't really mean much in
this context) reported by AK8963 in MPU9250 on Navio 2.
this makes the HMC5843 use single-shot mode, which makes it more
robust to bus resets. It also adds WHOAMI checking and enables
automatic temperature compensation.
Unfortunately this makes existing calibration values incompatible, so
a re-cal is required. The device ID has been changed to reflect the
driver change.
RC_Channel: To nullptr from NULL.
AC_Fence: To nullptr from NULL.
AC_Avoidance: To nullptr from NULL.
AC_PrecLand: To nullptr from NULL.
DataFlash: To nullptr from NULL.
SITL: To nullptr from NULL.
GCS_MAVLink: To nullptr from NULL.
DataFlash: To nullptr from NULL.
AP_Compass: To nullptr from NULL.
Global: To nullptr from NULL.
Global: To nullptr from NULL.
Summary of significant changes:
-Autsave doesn't depend on STREAM_EXTRA3
-Don't risk only saving one compass on copter if CAL_ALWAYS_REBOOT is set
-Only calibrate compasses that are both health and marked for use (there was a inconsistency in handling the mask)
-Fix incorrect failure reporting on DO_ACCEPT_MAG_CAL with a mask of 0 if a channel was specifically not started
-Fix not starting the buzzer if the delay is set to 0 seconds
-Always send MAG_CAL_REPORT until its acknowledged
-Correct the field in MAG_CAL_REPORT for autosave to indicate if the compass had actually been saved, rather then being scheduled to be saved
-Remmove unused public interfaces
We currently check examples are buildable with waf which doesn't need
the libraries to be specified in a make.inc file. Having the makefiles
there is misleading since people try to build and realize the build is
broken.
The minimum version for gcc was supposed to be 4.9 for any platform.
However our build instructions are outdated. Remove the problematic
parts that use the sparse-endian.h header while we don't fix the setup
for windows.
- Correctly sort includes and add missing AP_Math.h
- Use anonymous struct for trim_registers in _load_trim_values,
renaming its members so they don't start with underscore
- Don't change _dig* values when we failed to read from sensor
- Add some blank lines
- Make _dig_* members be inside a _dig struct
- Use constrain_int32 instead of if/else chain
- s/time_us/time_usec/
- Construct raw_field with a single constructor in _update()
- Add missing copyright notice
- Group methods together in declaration
In addition:
- bbbmini, navio and navio2 can force HMC5843 backend to
be external.
- there was a typo in the backend name that's now fixed:
AK8953 vs AK8963
Minlure has an onboard compass (HMC5883L) as slave of MPU-6000, but also
allows the use of an external HMC5883L compass, which should be
connected to the lure's I2C port.
That rotation is done because of the "arrow" pointing the sensor direction in
3DR GPS+Compass kit (which isn't natural to the sensor orientation, by the
way). Thus, do that rotation only for external HMC5883L compasses.
That rotation is set for AP_COMPASS_TYPE_HMC5883L, because it's usually
the compass from 3DR GPS+Compass kit, which has an arrow pointing the
"correct" direction. That rotation should be done before rotate_field()
as it represents the "standard" position for the kit.
This patch also makes published values consistent with respect to rotation.
Before this, raw fields used in calibration were published with a
rotation different from the filtered field when _product_id is
AP_COMPASS_TYPE_HMC5883L.
And to the detection probe() method. That way we don't need to use a board
`#ifdef` inside the class code. Additionally, we make raspilot board use it.
Initialization was also changed a little bit so we don't try to
initialize 25 times. We rather use the same methods as in the
AP_InertialSensor drivers.
Also move up the call to is_zero() in read_raw so we don't set
_mag_[x|y|z] in case of failure.
These are not used. The only place where raw fields are used are in the
compass calibrator and we don't need to store them.
Additionally remove duplicated documentation about the meaning of the
functions to avoid them getting out of sync.
We still need the BusDriver (in some places called SerialBus) interface
since this driver can also be used on an AuxiliaryBus and that has a
different interface.
- Capitalize and rename constants
- Make clear what gain is applied in calibration and what is the
"normal" gain
- Make the separation between HMC5883L and HMC5843 explicit when it
makes sense to improve readability
- Remove spurious delay in calibrate function
We still need the BusDriver (in some places called SerialBus) interface
since this driver can also be used on an AuxiliaryBus and that has a
different interface.
Besides the usual conversion some more improvements:
- Use generic function to convert endianness
- Minor cleanups
- Reorder per-board ifdefs in compass instantiation: distinguish when
there's a default compass to when it should probe other compasses
In file included from /home/lucas/p/dronecode/ardupilot/libraries/AP_Compass/Compass.h:6:
/home/lucas/p/dronecode/ardupilot/libraries/AP_Compass/CompassCalibrator.h:86:5: warning: struct 'param_t' was previously declared as a class [-Wmismatched-tags]
struct param_t _params;
^
/home/lucas/p/dronecode/ardupilot/libraries/AP_Compass/CompassCalibrator.h:44:11: note: previous use is here
class param_t {
^
/home/lucas/p/dronecode/ardupilot/libraries/AP_Compass/CompassCalibrator.h:86:5: note: did you mean class here?
struct param_t _params;
^~~~~~
Not having data ready during initialization is normal. Don't print error
message since it can mislead people to think the compass was not
initialized successfully.
This is the only driver doing this, using the system_initializing() from
scheduler to log selectively. Remove the check together with removal of
unused wrapper methods to semaphore.
Dr.-Ing. Amilcar Do Carmo Lucas
murata
Peter Barker
Andrew Tridgell
Eugene Shamaev
Pierre Kancir
Lucas De Marchi
Tom Pittenger
Jacob Walser
Randy Mackay
Georgii Staroselskii
Alexey Bulatov
Siddharth Bharat Purohit
Michael du Breuil
Mathieu OTHACEHE
Andy Little
Jonathan Challinger
José Roberto de Souza
Gustavo Jose de Sousa
Matt
dgrat
Ricardo de Almeida Gonzaga
mirkix
Víctor Mayoral Vilches
Julien BERAUD