we only accept a lidar if it changes by 5% of its full range, and we
reject a lidar again if the correction between barometric and lidar
range changes by more than 30m
This allows us to cope with faulty lidars which may give a constant
reading
when aborting a landing via mode change, check if NAV_CONTINUE_AND_CHANGE_ALT is after LAND. If so, go ahead and execute it. Else, normal behavior or check do_land_start else decrement mission index
- previously we only kept track of starting flying while in auto which gets reset when switching in and out of auto and on takeoff/land. Now we keep track of a "global" one that will track the is_flying flag regardless of the flight mode.
fixes https://github.com/diydrones/ardupilot/issues/2778
When executing a takeoff, and the throttle is suppressed, but we're already flying, we should unsuppress the throttle. We can get into this situation if we reset the mission in-flight.
- enabled via new param LAND_ABORT_THR default is 0 (disabled)
- Triggered via 95% throttle during landing, a landing abort will take place.
- This copies all takeoff params for right now, we can make this better later if needed
- added mission item command to NAV_LAND which is the abort takeoff altitude. If 0 then use last takeoff if available, else use 30m
- hold heading, just like takeoff, until altitude is reached
- pitch is constrained to takeoff pitch, or else 10deg if not available
- After abort altitude is reached, the normal landing restart happens (DO_LAND_START or decrement mission)
- restart landing by jumping to DO_LAND_START or decrement mission on mode change
Use waypoint bearing if available, otherwise use gps projected ahead 1km else yaw
Perform update before making decision to finish cmd so it always executes
We don't need those comments anymore, now that we log the task name. Also,
keeping the comments means that we need to fix them when tasks are added in the
middle, not to mention the problem with tasks that are added selectively (i.e.,
guarded by preprocessor directives).
* Retains ability to read from Analog Pin
* Adds ability to read RSSI from PWM channel value as is done in OpenLRSng, EazyUHF, and various other LRS.
* Handles any type of RSSI that provides RSSI values inverted - i.e. when the low value is the best signal and the high value is the worst signal.
* Has different key names from all existing RSSI parameters to provide for a clean break and easier distinguishing.
* Existing parameters are marked as obsolete
This behavior is excessively paranoid about clearing the flag so now it's extra sticky. You can only clear the is_crashed flag when:
- changing modes
- starting to execute a takeoff wp (if mission/index gets reset while still in auto)
- while in takeoff and throttle is suppressed it's held false
behavior that was removed:
- clear flag when starting to execute any nav cmd (reached next wp)
- if while crashed, you "start flying again" (non-sticky)
due to zero-ish vibration in SITL, the is_flying check thinks you're not flying, and this thinks you crashed. This is a SITL specific problem but it brings to light that *if* someone actually had a very low vibration aircraft we don't want to crash them. So, the vibe test has been removed for now. A better test is a variance on the accel
add crash detection, allow disengage via param CRASH_DETECT
improved is_flying behavior
take off, landing and hard-landing improvements
add stillness check to is_flying and log it
minimum airspeed is determined ARSPD_FBW_MIN*0.75
Param 1 of CONTINUE_AND_CHANGE_ALT now denotes which direction the
user expects the plane to travel when changing altitude:
0 = no expectation, command completes when within 5 m of altitude.
1 = climb expected, command completes at or above altitude.
2 = descent expected, command completes at or below altitude.
this fixes a bug where a mode switch change during an AUTO mission
which does not change the flight mode would cause cross tracking to be
reset, so the plane will not correctly follow the desired track
Many thanks to Michael Du Breuil for the log that showed this bug
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
If someone mistakenly puts all 0's in their LAND command then
total_distance will be calculated as 0 and cause a divide by 0 error
below thus crashing ArduPilot. Lets avoid that.
Whenever next waypoint is within the loiter radius, maintaining loiter would prevent us from ever pointing toward the next waypoint. Hence for very close waypoints loiter_to_alt becomes verified by the altitude only.
Andrew Tridgell
Randy Mackay
Stewart Loving-Gibbard
squilter
Grant Morphett
Peter Barker
Staroselskii Georgii
Tom Pittenger
Siddharth Bharat Purohit
Peter Barker
Gustavo Jose de Sousa
André Kjellstrup
ziltoid2
Michael Day
Przemek Lekston
pepevalbe
Lucas De Marchi