- always check with state machine before reboot/shutdown
- respect BOARD_HAS_POWER_CONTROL (shutdown from command, low battery, power button)
- px4_shutdown_request add optional delay and always execute from HPWORK
- px4_shutdown_request split out px4_reboot_request
- increase stack sizes to run cleanly under stackcheck
- this is likely overkill for most boards, but using stackcheck to set our minimum ensures we have a very safe margin on regular builds and it's something we can currently afford
- remove holybro_durandal-v1_stackcheck from test rack (there's only one unit)
- this doesn't currently change anything, but gets us ready to start
experimenting with using the small amount of instruction tightly memory
on STM32F7
- the .ramfuncs section works with NuttX CONFIG_ARCH_RAMFUNCS
- interupt pin set active low and latch
- relax retry timeout if configure failed
- improve configured empty rate (sample rate) rounding
- fix RegisterCheck
- check FIFO count as part of full transfer and reset or adjust timing if necessary
- rename DRV_IMU_DEVTYPE_ICM20608 -> DRV_IMU_DEVTYPE_ICM20608G
- update to NuttX with stm32f4 and stm32f7 SPI DMA internal buffers
- remove explicit DMA buffer allocations from new IMU drivers
- restore original BOARD_DMA_ALLOC_POOL_SIZE
- decrease SPI DMA thresholds based on fmu-v2/v3/v4/v5 bench testing
Removes the calibration on startup, as these values were overwritten by
the system calibration values anyway.
So the only difference is that if all calibration scales were equal to 1,
the driver startup would have failed.
* MC_HTE: unitialize with hover_thrust parameter
* MC_HTE: constrain hover thrust setter between 0.1 and 0.9
* MC_HTE: integrate with land detector and velocity controller
* MCHoverThrustEstimator: Always publish an estimate even when not fusing measurements. This is required as the land detector and the position controller need to receive a hover thrust value.
* MC_HTE: use altitude agl threshold to start the estimator
local_position.z is relative to the origin of the EKF while dist_bottom
is above ground
Co-authored-by: bresch <brescianimathieu@gmail.com>
This avoids the need for recalibration, and also cleans up other driver
ID's (merge separate accel/gyro).
The SPI address was previously set to a board-specific (arbitrary) value,
and is now set to 0. This will allow extending for multiple sensors of the
same type on the same bus.
Chip-select and SPI initialization uses the new config, whereas the drivers
still use the existing defines.
The configuration in board_config.h can be removed after all drivers are
updated.
- reduces amount of board configuration required
- removes the cyclic dependency between io_timers_t and timer_io_channels_t
Fixes a bug in the fmuk66-v3 config: the 2. timer has 3 channels associated
not 2.
Fixes a bug in the modelai config: the 2. timer has 4 channels associated.
- it does nothing useful
- increases boot time by 2 seconds on pixhawk 4 due to a poll timeout:
IST8310 on I2C bus 3 at 0x0e (bus: 100 KHz, max: 400 KHz)
WARN [ist8310] ERROR: TIMEOUT 2
- this is a new module for temperature compensation that consolidates the functionality previously handled in the sensors module (calculating runtime thermal corrections) and the events module (online thermal calibration)
- by collecting this functionality into a single module we can optionally disable it on systems where it's not used and save some flash (if disabled at build time) or memory (disabled at run time)
and remove the px4_ prefix, except for px4_config.h.
command to update includes:
for k in app.h atomic.h cli.h console_buffer.h defines.h getopt.h i2c.h init.h log.h micro_hal.h module.h module_params.h param.h param_macros.h posix.h sem.h sem.hpp shmem.h shutdown.h tasks.h time.h workqueue.h; do for i in $(grep -rl 'include <px4_'$k src platforms boards); do sed -i 's/#include <px4_'$k'/#include <px4_platform_common\/'$k/ $i; done; done
for in $(grep -rl 'include <px4_config.h' src platforms boards); do sed -i 's/#include <px4_config.h/#include <px4_platform_common\/px4_config.h'/ $i; done
Transitional headers for submodules are added (px4_{defines,log,time}.h)
On more complicated setups it's still possible to exceed 32 tasks. For example fmu-v5 with mavlink on every telem (+ USB), external spi usage (pmw3901), gimbal (vmount), multiple i2c sensors, and camera feedback is 35 tasks (with top running). This is a fairly extreme case, so I'm only going to increase CONFIG_MAX_TASKS on newer F7 boards.
* adds a work_queue systemcmd that will bring a tree view of all active work queues and work items
* WorkQueues now track attached WorkItems and will shutdown when the last WorkItem is detached
-moved rc.mavlink to the boards optional rc additions (now it's called rc.board_mavlink) to handle board specific mavlink needs (mavlink over usb, ethernet, additional streams, etc.)
-mavlink module will be responsible to usb defaults, therefore less args are needed to be passed to mavlink module if one wants to use mavlink over usb.
-the way to check if connection is usb is by it's designated variable and not by config mode.
David Sidrane
SalimTerryLi
Daniel Agar
mcsauder
Beat Küng
garfieldG
BazookaJoe1900