Commit Graph

334 Commits

Author SHA1 Message Date
James Bielman 5631f865b2 Update floating point calculations to use floats instead of doubles.
- Allows use of hardware floating point on the Cortex-M4.
- Added "f" suffix to floating point literals.
- Call floating point versions of stdlib math functions.
2013-01-16 13:52:01 +11:00
Randy Mackay fef7569dee Copter: added experimental LOITER_REPOSITIONING #define to config.h
APM_Config.h should be used to overriding the standard parameters but
they still require a definition in config.h or they will be undefined
when built by the mission planner.
2013-01-14 13:34:14 +09:00
Randy Mackay 9ad6f711f8 ArduCopter: replace FS_THR_RTL_MIN_DISTANCE with wp_radius
This effectively means that an RTL kicked off by a failsafe will
immediately switch to LAND mode only if within 2 meters.  Previously the
radius was much wider (15m).
2013-01-13 20:00:47 +11:00
Randy Mackay 12f885c33c ArduCopter: disable ITERM logging by default
This message takes 1ms to write and we are running over our limits on
some loops.
2013-01-13 20:00:39 +11:00
rmackay9 21b6c78d12 ArduCopter: added get_throttle_althold_with_slew to allow slower altitude target changes
Improved surface tracking by using slewed althold controller
Reduced sonar mode filter to just 3 elements to reduce lag but at the possible consequence of allowing sonar noise to creep through for people with margin sonar set-ups.
2013-01-13 19:51:47 +11:00
Randy Mackay 87627d883b ArduCopter: use new logging method for remaining packet types
Additional changes include renaming RAW dataflash type to IMU
2013-01-13 00:17:44 +09:00
James Bielman 7827a4a54a ArduCopter: Add AP_HAL_SMACCM support.
- Added default configuration to "config.h".
- Added main function to run under FreeRTOS with HWF4.
2013-01-09 11:19:51 -08:00
James Bielman ab37f833db MS5611: Fix CONFIG_MS5611_SERIAL definitions.
- Make sure the values are defined as integers.  We were always using
  SPI rather than using I2C when desired.
2013-01-09 11:19:51 -08:00
Andrew Tridgell c48714be16 Copter: enabled PX4 sensors 2013-01-05 20:39:31 +11:00
James Bielman 264db3670e AP_Baro: Add CONFIG_MS5611_SERIAL option to choose between SPI and I2C.
- Update ArduCopter and ArduPlane modules to pass the correct serial
  driver to the MS5611 driver.
- Update barometer examples, assuming SPI.
2013-01-03 13:48:06 -08:00
Andrew Tridgell 94e3322e24 Copter: fixed build on px4 2013-01-02 22:09:02 +11:00
rmackay9 9b2956b377 ArduCopter: increase throttle rate P to 6.0 (was 1.0) and alt hold P to 2.0 (was 1.0) 2013-01-02 09:55:37 +11:00
rmackay9 d400e5040b ArduCopter: turn on INERTIAL_NAV_Z in the config.h file so that it takes effect when built for the mission planner 2013-01-02 09:55:37 +11:00
rmackay9 e850ab7ccd ArduCopter: add AUTO_VELZ_MIN, AUTO_VELZ_MAX and PILOT_VELZ_MAX to allow better control of climb/descent rate in auto and manual throttle modes 2013-01-02 09:24:31 +11:00
rmackay9 5526ca204c ArduCopter: on throttle failsafe, only initiate RTL if we are at least 15m from home 2013-01-02 09:22:51 +11:00
Robert Lefebvre 6e64b1b357 ACM: Precision Loiter RePositioning code.
Protected behind a #define
2013-01-02 09:19:39 +11:00
rmackay9 e6519330f4 ArduCopter: remove unused rc_override variables to save 21 bytes 2013-01-02 09:19:17 +11:00
rmackay9 34e18ae12a ArduCopter: increase accel based throttle PIDs and add D term to rate based throttle 2013-01-02 09:19:17 +11:00
Robert Lefebvre 9605bd8ee1 ACM: Trying to set a default MPU6K filter rate of 10Hz for TradHeli. Doesn't Work. 2013-01-02 09:14:55 +11:00
rmackay9 d8e3d5c10c ArduCopter: allow RTL's yaw mode to be overridden with a #define in APM_Config.h 2013-01-02 09:12:40 +11:00
rmackay9 50d46898fb ArduCopter: allow GUIDED mode roll-pitch, yaw and throttle control modes to be overridden 2013-01-02 09:12:17 +11:00
Andrew Tridgell 9e986801c9 Copter: fixed SITL for ArduCopter 2012-12-20 14:52:34 +11:00
Pat Hickey 5e63491994 ArduCopter: fix issues with HAL/HIL mixup and baro/compass instances 2012-12-20 14:52:29 +11:00
Pat Hickey d93d932831 ArduCopter: defines fixes
Conflicts:

	libraries/AP_Common/Arduino.mk
2012-12-20 14:52:28 +11:00
Pat Hickey 2aa4657315 ArduCopter: changes to use CONFIG_HIL_BOARD 2012-12-20 14:52:28 +11:00
rmackay9 2f748f8382 ArduCopter: renamed BATT_FAILSAFE to FS_BATT_ENABLE 2012-12-10 23:47:14 +09:00
rmackay9 d31efebd44 ArduCopter: rename throttle failsafe parameters.
Switch to LAND flight mode if throttle failsafe triggers and we do not have a GPS.
THR_FAILSAFE renamed to FS_THR_ENABLE.
THR_FS_VALUE renamed to FS_THR_VALUE.
THR_FS_ACTION removed (action is now controlled by setting FS_THR parameter).
2012-12-10 23:38:43 +09:00
rmackay9 2f1b2b70e6 ArduCopter: added ACRO_TRAINER parameter to allow enabling/disabling the acro training function which will bring the roll back to within +- 45 degrees 2012-12-10 22:27:46 +09:00
rmackay9 dadad8677e ArduCopter: added descriptions for most parameters that did not have them
Renamed loiter_radius to circle_radius to better reflect it's purpose.
Removed some unused parameters including WP_MODE, WP_MUST_INDEX, LOG_LASTFILE, AXIS_P
2012-12-10 21:45:57 +09:00
rmackay9 cfe2507c0b ArduCopter: reduce Rate Roll/Pitch P to 0.150 (was 0.175) and increase I to 0.1 (was 0.01) 2012-12-09 18:08:45 +09:00
Robert Lefebvre aa4d4f8c24 ACM: Adding Pre-Compiler Define for Stabilize Throttle Mode. 2012-12-08 20:41:05 -05:00
Robert Lefebvre 1b97a92098 ACM: Code Cleanup 2012-12-08 14:49:38 -05:00
rmackay9 f98a807d36 ArduCopter: remove debug related to yaw mode used for alt hold 2012-12-08 14:24:50 +09:00
rmackay9 9dd978576b ArduCopter: auto yaw changes to allow pilot override of yaw during missions
Added set_yaw_mode to better control of yaw controller changes and variable initialisation.
Replaced AUTO_YAW mode with separate yaw controllers YAW_LOOK_AT_NEXT_WP, YAW_LOOK_AT_LOCATION, YAW_LOOK_AT_HEADING.
Pilot manual override of yaw causes yaw to change to YAW_HOLD (i.e. manual yaw) until next waypoint is reached.
Added get_yaw_slew function to control how quickly autopilot turns copter
Changed YAW_LOOK_AHEAD to use GPS heading and moved to new get_look_ahead_yaw function in Attitude.pde
Renamed variables: target_bearing->wp_bearing, original_target_bearing->original_wp_bearing.
Removed auto_yaw_tracking and auto_yaw variables and update_auto_yaw function as they are no longer needed.
Simplified MAV_CMD_CONDITION_YAW handling (do_yaw).  We lose ability to control direction of turn and ability to do long panorama shots but it now works between waypoints and save 20bytes.
2012-12-08 14:23:32 +09:00
rmackay9 68ca123224 ArduCopter: remove some unused #defines 2012-12-07 15:17:35 +09:00
rmackay9 3a90fc77f9 ArduCopter: add dataflash logging of camera events 2012-12-07 00:57:08 +09:00
rmackay9 a5bb54e36e ArduCopter: RTL clean-up and slightly improved landing sensor
Consolidated RTL state to be captured by rtl_state variable.
Combined update_RTL_Nav and verify_RTL functions which performed the same function but one was for missions, the other for the RTL flight mode.
Renamed some RTL parameters and global variables to have RTL at the front.
Landing detector now checks accel-throttle's I term and/or a very low throttle value
2012-12-06 10:31:52 +09:00
rmackay9 072ffec493 ArduCopter: allow INERTIAL_NAV to be enabled separately for horizontal and vertical position 2012-12-06 10:31:41 +09:00
rmackay9 bdb47c449a ArduCopter: pass linear altitude error to throttle rate controllers.
Previously the requested rate used the square root of the altitude error.

Scale pilot's desired vertical rate and acceleration based on ACCELERATION_MAX_Z and VELOCITY_MAX_Z #defines
2012-12-06 10:31:31 +09:00
rmackay9 7b4ed2d227 ArduCopter: restored landing detector to landing throttle mode.
Added LAND_SPEED parameter to control the rate of descent for the last 10m of a landing.
Added CH6 tuning for accel based throttle controller.
2012-12-06 10:31:20 +09:00
rmackay9 560bb1d738 ArduCopter: removed unused AUTO_THROTTLE_HOLD #define 2012-12-06 10:31:15 +09:00
rmackay9 3cbef57c64 ArduCopter: first merge of leonard's accel based altitude controller plus other changes from Randy
Changes include:
New low-level get_throttle_accel function takes target acceleration and compares vs earth-frame Z accelerometer values to produce output to motors.
Higher level throttle controllers modified to call new get_throttle_accel controller
Throttle_rate_stabilized controller added which maintains a desired climb/descent rate
Throttle_land controller added - descends using normal auto throttle controller to 10m then descends at 50cm/s
Multiple throttle modes added including landing mode
Land flight mode no longer needs GPS
Throttle cruise maintenance moved to update_throttle_cruise function
2012-12-06 10:30:49 +09:00
Andrew Tridgell 6fbf5ec8f2 Copter: update ArduCopter for new ins interface 2012-11-30 07:15:18 +11:00
Robert Lefebvre 6b8c39dd10 ACM: Creating Yaw_Look_Ahead yaw mode.
This function is not fully tested yet.
2012-11-26 21:37:13 -05:00
Robert Lefebvre 6ffc115236 Changes to get_throttle_rate()
Commented out a bit of code that is not used currently
Change the output constrains to #defines so they can be easily changed, particularly for use in TradHeli.
2012-11-21 17:11:38 -05:00
Andrew Tridgell dafaa2efc8 SITL: disable optical flow on the desktop build
it doesn't work yet, as no sensor emulator is available
2012-11-19 09:04:03 +11:00
rmackay9 07a7a1acd8 ArduCopter: replaced digitalRead and digitalWrite with faster calls
improved performance logging to dataflash
2012-11-19 01:16:07 +09:00
rmackay9 e92b560df5 ArduCopter: low baterry failsafe 2012-11-15 23:35:41 +09:00
Jason Short 9735a0eff1 ACM: Allow for user defined roll and pitch input max 2012-11-11 18:00:10 -08:00
rmackay9 e212744f4c ArduCopter: failsafe improvements
resolves momentary throttle drop to zero before failsafe engages
resolves motor cut after 30seconds if flying in stabilize without GPS (now switches to ALT_HOLD with target altitude zero)
disables motors if throttle was zero before failsafe event
2012-11-11 22:11:12 +09:00
Jason Short 129ec35c35 ACM crosstrack min distance 2012-11-09 22:15:16 -08:00
Jason Short 4d7b9137fe ACM: Added max RTL altitude 2012-11-09 22:15:15 -08:00
rmackay9 1f801714e8 ArduCopter: incorporate new version of inertial navigation
Moved several navigation functions from ArduCopter.pde to navigation.pde
2012-11-07 19:21:31 +09:00
Jason Short 73bc90f9b8 ACM: config.h cleanup
Added LOG_ITERM default to enabled
2012-10-27 09:59:57 -07:00
rmackay9 5e8043fd9c ArduCopter: changed ACRO_ROLL_STABILIZE and ACRO_PITCH_STABILIZE to parameters
Changes on behalf of Leonard Hall
2012-10-23 21:30:50 +09:00
rmackay9 78316adf75 ArduCopter: replace Serial.print with Serial.print_P to save memory.
Includes replacing flight_mode_strings with print_flight_mode function.
SendDebug macro replaced with direct Serial.print_P calls.
2012-10-22 16:45:24 +09:00
Robert Lefebvre bfade7d0ed Fixed that last commit
#define Stupid_Mistake
2012-10-18 16:50:42 -04:00
Robert Lefebvre 592f4040fd Changed RLT Yaw Mode for TradHeli. Also a few comment cleanups. 2012-10-18 16:39:05 -04:00
rmackay9 583f2e49a3 ArduCopter: integrated Leonard Hall's improved ACRO mode 2012-10-18 23:24:34 +09:00
rmackay9 7d7de976c3 ArduCopter: reduced optical flow's I and IMAX terms 2012-10-17 17:47:43 +09:00
LeonardTHall d7b7e1cefa New Yaw controller using rate feed forward and stabilize.
Signed-off-by: LeonardTHall <LeonardTHall@gmail.com>
2012-10-15 11:37:49 +09:00
rmackay9 ee5dab9647 ArduCopter: enable ACRO mode's AXIS_LOCK by default 2012-10-14 19:50:45 +09:00
rmackay9 997fe85880 ArduCopter: fixed acro mode
Changes included:
Removing earth frame roll_rate_trim, pitch_rate_trim and yaw_rate_trim.
Switch ACRO mode to use YAW_ACRO instead of YAW_HOLD.
Changed YAW_ACRO to use stabilize yaw when axis_enabled.
Reset ACRO roll, pitch and yaw targets to current attitude when first entering ACRO.
2012-10-14 17:47:46 +09:00
rmackay9 4a41a3d210 ArduCopter: added BATT_VOLT_PIN and BATT_CURR_PIN parameters to allow support for new 3DR IV battery voltage and current monitor 2012-10-13 18:40:46 +09:00
Robert Lefebvre dae81d2068 Added #define for Tilt_Compensation.
Also added some detail to WP_Speed_Max parameter.
2012-10-12 14:51:31 -04:00
rmackay9 03933df5b7 ArduCopter: set default rate roll and pitch I terms to 0.010, and rate yaw to 0.015
Updated after discussing with Marco
2012-10-11 17:25:01 +09:00
rmackay9 35fa50234f ArduCopter: move I terms from stabilize to rate controllers 2012-10-11 17:20:05 +09:00
rmackay9 af1d6a9b82 ArduCopter: reduce Stabilize Yaw P term to 4.5 2012-10-03 14:19:49 +09:00
rmackay9 ea4f256f8e ArduCopter: BATT_PIN parameter added to allow you to select which pin is used for voltage and current measurements
To save a parameter, the current sensor pin is assumed to always be 1 higher than the voltage pin.
2012-10-02 22:16:19 +09:00
rmackay9 95763e610b ArduCopter: allow DMP to run in parallel with DCM
Parallel DMP can be enabled by #define SECONDARY_DMP_ENABLED in APM_Config.h
New DMP dataflash log type added to allow easy comparison with DCM
2012-09-30 00:25:40 +09:00
rmackay9 41fbb19cf5 AP_InertialSensor_MPU6000: replaced _cs_pin parameter with #define and saved 1 byte of memory
Updated ArduCopter, ArduPlane and example sketches in AP_InertialSensor, AP_IMU and AP_AHRS libraries because they no longer need to pass in cs_pin to the constructor
2012-09-28 19:21:59 +09:00
rmackay9 fff5d51694 ArduCopter: reduced Loiter Rate I to 0.04 (was 0.08) 2012-09-25 19:08:31 +09:00
rmackay9 a71aa21514 ArduCopter: increase default Loiter Rate P to 5.0 2012-09-25 12:19:44 +09:00
rmackay9 9e66b555cb ArduCopter: removed INSTANT_PWM from ArduCopter and AP_Motors library 2012-09-13 21:31:13 +09:00
rmackay9 42406c827a ArduCopter: added NUM_IMU_SAMPLES_FOR_XYZHZ definitions for MPU6000 and Oilpan to allow more syncing of the mainloop with the arrival of data from the IMU. 2012-09-10 11:37:48 +09:00
Craig Elder 274b2e2143 Arducopter: Release 2.7.2 2012-08-31 19:18:10 -07:00
Andrew Tridgell e8d928cca4 ACM: added TELEM_DELAY to ArduCopter 2012-08-30 09:03:01 +10:00
Craig Elder 4ad516c445 Arducopter: increased MAVLINK delay to 6s to reduce the chance of xBee bricking
Arduplane:  increased MAVLINK delay to 6s to reduce the chance of xBee bricking
Ardurover:  increased MAVLINK delay to 6s to reduce the chance of xBee bricking
2012-08-28 20:09:10 -07:00
rmackay9 2ad6dcb7c4 ArduCopter: increased Stabilize Roll and Pitch I term to 0.05 (was 0.01) based on feedback from Jason 2012-08-29 11:34:53 +09:00
rmackay9 b4b394e67e ArduCopter: reduced Rate Roll and Pitch PID values
RATE_ROLL_P, RATE_PITCH_P reduced to 0.165 (was 0.185)
RATE_ROLL_D, RATE_PITCH_D reduced to 0.004 (was 0.008)
2012-08-26 10:45:45 +09:00
uncrustify 429c41155c uncrustify ArduCopter/config.h 2012-08-21 19:19:50 -07:00
Andrew Tridgell 6d11940ada AHRS: removed Quaternion build support from APM/ACM/rover 2012-08-22 10:42:21 +10:00
rmackay9 1d32e03f61 ArduCopter: added ACCEL_ALT_HOLD and INERTIAL_NAV to config.h and commented out of APM_Config.h.
Reduces possibility of difference between arduino ide compiled code and script built code (i.e. autotester, mission planner)
2012-08-19 12:31:02 +09:00
Jason Short 3ee2fd3fb6 ACM: Config.h - added default for toy mixer 2012-08-16 15:40:28 -07:00
Jason Short 9a568385b0 ACM increase the minimum speed at WP 2012-08-10 10:01:40 -07:00
Jason Short 3e57f8afd8 ACM: config.h = updated default gains
More yaw rate control
2012-08-09 16:59:43 -07:00
Amilcar Lucas d34549f386 Add an optional second mount to ArduPlane and ArduCopter 2012-08-08 23:22:24 +02:00
Amilcar Lucas 9cc705939a Add a second mount instance 2012-08-08 23:07:25 +02:00
Amilcar Lucas aa3cc63b15 ArduCopter: Make the code fit in a 1280 chip again
Even allows to control a camera/antenna mount, if the user explicitly wants to.
2012-08-06 00:23:48 +02:00
Amilcar Lucas 0106c133cf Default CLI_SLIDER_ENABLED to DISABLED
Chris asked for this on the mailing list
2012-08-06 00:22:33 +02:00
Amilcar Lucas afd96025a7 ArduCopter: Save more space in APM1280 2012-08-05 23:05:52 +02:00
Amilcar Lucas d29f7023cc Merge from ArduPlane 2012-08-04 18:38:50 +02:00
rmackay9 77b1785bc6 ArduCopter: reduce stabilize roll, pitch and rate yaw IMAX values 2012-07-30 11:01:45 +09:00
rmackay9 014f5aae99 ArduCopter: added DMP_ENABLE #define and CH6 tuning value for AHRS_KP 2012-07-28 14:21:07 +09:00
Jason Short 96aabb7712 ACM: Lowered default Alt hold P 2012-07-21 16:45:00 -07:00
Jason Short 3b496ff229 Arducopter: Upped D rate to .005 by default 2012-07-19 22:35:21 -07:00
Jason Short 49c7579079 Arducopter: Config.h defaults adjustments 2012-07-19 17:48:48 -07:00
Jason Short 3401bd3583 Arducopter: Clarified units in comment 2012-07-19 09:49:13 -07:00
Jason Short dcf9f9dab1 Arducopter
for rate altitude changes
2012-07-18 22:57:10 -07:00
Andreas M. Antonopoulos a976a59c88 AP_Limits: Configuration defaults moved to config.h. Fixed AP_LIMITS==DISABLED handling. 2012-07-16 11:46:43 -07:00