Mirror
/
ardupilot
mirror of https://github.com/ArduPilot/ardupilot
5
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
11,250 Commits 71 Branches 509 Tags 763 MiB
Commit Graph

403 Commits

Author SHA1 Message Date
Andrew Tridgell 056e0ca40d Plane: APM2 doesn't have channel 9 PWM output 2013-06-24 13:06:54 +10:00
Andrew Tridgell 641ad6bc63 Plane: increase time allowed for update_alt() 
the altitude tracking code can be quite expensive with TECS
 2013-06-07 08:41:09 +10:00
Andrew Tridgell b27ffdd087 Plane: new plane beta 2.74beta2 2013-06-04 15:10:11 +10:00
Andrew Tridgell c008fa764c Plane: update_commands() can take 7ms if it needs to write a waypoint 2013-06-04 13:42:25 +10:00
Andrew Tridgell 93cd0f9a31 Plane: switch to new AP_Scheduler 
this gives us more accurate task scheduling in ArduPlane, plus better
monitoring of task timing (via SCHED_DEBUG)
 2013-06-04 13:34:58 +10:00
Andrew Tridgell 02d72ffcba Plane: make it possible to change board orientation at runtime 2013-06-03 16:52:44 +10:00
Andrew Tridgell 4c9bc30f58 Plane: make it possible to change control channel ordering without reboot 
this makes configuration a bit easier
 2013-06-03 16:42:38 +10:00
Andrew Tridgell fb9bf21522 Plane: allow channel mapping of first 4 channels 
this makes it easier to support DSM and SBUS radios
 2013-06-03 16:23:48 +10:00
Andrew Tridgell f7697574db Plane: use the new airspeed driver interface 
the choice of analog source is now in the airspeed driver
 2013-06-03 11:51:09 +10:00
Andrew Tridgell bb3171ab5f Plane: zero attitude integrators on the ground 2013-06-01 22:29:38 +10:00
Andrew Tridgell cd55ed45e2 Plane: removed the old roll/pitch/yaw PID controllers 
use the new controllers, with auto parameter conversion
 2013-05-31 14:06:56 +10:00
Andrew Tridgell eba7d6da9a Plane: removed the old crash_timer code 
This code is less relevent with the new L1 navigation, and could cause
issues with the pilot not having control after a long dive.

Thanks to Soren for pointing out the issues

See issue #305
 2013-05-28 11:19:28 +10:00
Andrew Tridgell dd633fcf3f Plane: make voltage and battery capacity failsafe settable at runtime 
this also fixes issue #292
 2013-05-22 20:33:57 +10:00
Andrew Tridgell bd4b7d136f Plane: mark ArduPlane 2.74beta 2013-05-13 17:32:33 +10:00
Andrew Tridgell 001d18b51d Plane: removed scaling of pitot source 2013-05-13 15:19:05 +10:00
Andrew Tridgell 97b6aaac77 Plane: use voltage_average() for RSSI 
this fixes it on PX4
 2013-05-13 15:19:05 +10:00
priseborough 854c50501d Plane: Added a constraint to demanded bank angle during FBW-A mode to prevent roll limits being exceeded 2013-05-07 11:01:05 +10:00
Andrew Tridgell 0cf49308af Plane: mark a 2.73beta release 2013-05-05 22:36:22 +10:00
Andrew Tridgell 0e6a64fc14 Plane: reset roll/pitch integrators for APM_Control in takeoff 
when airspeed is below airspeed minimum. This is consistent with the
previous controllers

Pair-Programmed-With: Paul Riseborough <p_riseborough@live.com.au>
 2013-05-05 22:03:13 +10:00
Andrew Tridgell 4e2b88f6e6 Plane: added ATT_CONTROLLER option to select attitude controller 
set to 1 for the new APM_Control library
 2013-05-05 21:51:09 +10:00
Andrew Tridgell 3cd52a9689 Plane: fixes for AP_Baro_HIL 2013-05-02 15:09:27 +10:00
Andrew Tridgell 855277fa85 Plane: get ready for 2.72 release 2013-04-28 15:56:30 +10:00
Andrew Tridgell b53e3bb1fc Plane: log GPS messages as they come in 
stops us logging duplicate messages
 2013-04-28 14:56:31 +10:00
Andrew Tridgell 0b8c2da4df Plane: support 12 output channels on PX4 2013-04-25 20:10:53 +10:00
Andrew Tridgell ac7561c5d5 Plane: mark 2.72beta version 2013-04-24 16:19:18 +10:00
Andrew Tridgell 2e5834cc7f Plane: print flight mode as string in logs 2013-04-20 15:18:10 +10:00
Andrew Tridgell 5c553852ed Plane: when logging is disabled don't include DataFlash at all 2013-04-20 13:52:36 +10:00
Andrew Tridgell 0c5b393919 Plane: added compass logging 2013-04-20 13:52:36 +10:00
Andrew Tridgell c8af70a18d Plane: make the plane code compatible with the new logging system 
not actually converted yet
 2013-04-20 13:52:36 +10:00
Andrew Tridgell abe4dba871 Plane: added PX4 flash logging 2013-04-17 21:35:27 +10:00
Andrew Tridgell 42344455c9 Plane: fixed structure init for arduino compiler 2013-04-15 21:59:07 +10:00
Andrew Tridgell 75f4a43e2d Plane: fixed LOITER_TURNS command 
and cleanup more loiter variables
 2013-04-15 21:31:11 +10:00
Andrew Tridgell 82cd391cf8 Plane: use RADIUS_OF_EARTH define 2013-04-15 14:55:58 +10:00
Andrew Tridgell 8f091e70c8 Plane: move elevon variables into a structure 2013-04-15 14:53:56 +10:00
Andrew Tridgell 79c6f32400 Plane: made variables static and remove initial rc overrides 
minor code size savings
 2013-04-15 14:46:01 +10:00
Andrew Tridgell 8d2cf6f3e5 Plane: update author list 2013-04-12 22:01:41 +10:00
priseborough 70a186464b Plane: added LEVEL_ROLL_LIMIT parameter 
this replaces both TKOFF_HEAD_HOLD and RUDDER_STEER, allowing users to
instead select a roll limit for takeoff and landing
 2013-04-12 21:59:52 +10:00
Andrew Tridgell 575f346e85 Plane: removed HIL_MODE_ATTITUDE 
we really need full sensors for HIL with the L1 controller. The flight
is also _much_ better with sensors HIL.
 2013-04-12 17:44:40 +10:00
Andrew Tridgell 11eb0cfce1 Plane: update for new AP_Navigation controller class 
this switches ArduPlane over to use the L1 navigation controller, via
a generic nav_controller object pointer.

Note that the nav_controller controls all types of navigation now,
including level flight and heading hold. This provides a cleaner
abstraction than the old method of special case navigation handling

Pair-Programmed-With: Paul Riseborough <p_riseborough@live.com.au>
 2013-04-12 12:48:09 +10:00
Andrew Tridgell dcbe144c7e Plane: prepare for release of 2.71 2013-04-06 17:27:21 +11:00
Andrew Tridgell c5e2cfcc3e Plane: preparing for 2.71-beta 2013-04-02 09:25:24 +11:00
Andrew Tridgell 7db7d7db77 Plane: change FBWB altitude control algorithm 
this makes FBWB much less sensitive to airframe tuning. When the
elevator stick first goes neutral it locks in the current altitude as
the target altitude. When the elevator stick is off neutral, it moves
the target altitude in proportion to the elevator, at a rate goverened
by the new FBWB_CLIMB_RATE parameter

This prevents the aircraft from slowly drifting in altitude in FBWB,
and gives a more intuitive control mechanism for altitude.

Thanks to Chris Miser from Falcon UAV for help in designing this
change
 2013-03-28 10:27:25 +11:00
Randy Mackay a49fe272ad Plane: replace gps fix with status 
Required to ensure 3d fix is used for initialising home
 2013-03-27 11:42:02 +09:00
Andrew Tridgell f077f54e6a Plane: added TKOFF_HEAD_HOLD option 
this allows control over whether ArduPlane tries to hold heading
during auto takeoff. For hand launches it can be better to hold the
wings level and not attempt to hold heading during takeoff to prevent
the possibility of a stall during the climb out.

Thanks to Chris Miser from Falcon UAV for the feedback that led to
this option.
 2013-03-27 10:27:14 +11:00
Andrew Tridgell 1d983b3f2e Plane: fixed X accel triggering of auto 2013-03-22 11:53:45 +11:00
Andrew Tridgell 1ebaa14a99 Plane: prepare for 2.70 release 2013-02-21 09:49:15 +11:00
Andrew Tridgell 2f677acf3b Plane: update firmware version to 2.69 2013-02-11 15:02:08 +11:00
Andrew Tridgell 9f70c6c70d Plane: make CIRCLE mode hold altitude 
this will prevent us losing a lot of altitude during the initial
failsafe phase
 2013-02-11 13:52:25 +11:00
Jochen Tuchbreiter c5f19f5df8 Plane: Implement issue 80: counterclockwise loiter 
- libraries/AP_Common/AP_Common.h: Use bit 2 of Location.options to store
  loiter direction
- ArduPlane/defines.h: New bitmask MASK_OPTIONS_LOITER_DIRECTION for struct
  Location bit 2
- ArduPlane/ArduPlane.pde: New variable loiter_direction
- ArduPlane/GCS_Mavlink.pde: For mavlink loiter-commands use sign of param3 to
  detemine direction. Set Location.option flag accordingly
- ArduPlane/commands.pde: Make sure loiter-directions get saved into EEPROM
  correctly
- ArduPlane/commands_logic.pde: Set loiter_direction on all loiter-actions
  as well as RTL/instant loiter
- ArduPlane/navigation.pde: Yield loiter_direction in update_loiter
 2013-02-05 10:29:31 +11:00
Andrew Tridgell ebb7f27962 Plane: minor signed/type fixups 2013-01-27 13:16:26 +11:00
Andrew Tridgell 3caaa27526 Plane: fixed build errors in logging 2013-01-27 12:58:50 +11:00
Randy Mackay 7297a1ff83 Plane: renamed RAW dataflash message to IMU 2013-01-26 17:29:29 +09:00
Randy Mackay e674626fd6 Plane: rename CUR and CURR to CURRENT for logging 
Based on user complaint that log was enabled/disabled using CUR while
message that appeared in log was CURR.
 2013-01-26 17:19:42 +09:00
Randy Mackay 6f46f4a7d0 Plane: logging changes to use new faster packet method 
also RAW message renamed to IMU
 2013-01-26 17:07:21 +09:00
Randy Mackay d2767b911c AP_Math: switch get_distance_cm to return uint32_t 
Includes changes required on ArduCopter and ArduPlane side as well
 2013-01-26 17:04:12 +09:00
Andrew Tridgell 4d9a74d742 Plane: cleanup driver declaration 
remove a lot of the #if nesting
 2013-01-21 16:08:55 +11:00
Andrew Tridgell 4deee014d6 Plane: setup PX4 airspeed analog port 2013-01-21 13:56:28 +11:00
Andrew Tridgell 92c9a4c1ce Plane: start update logging for new API 2013-01-13 17:31:42 +11:00
Andrew Tridgell bea9a9d558 Plane: move memcheck_init() earlier in setup() 2013-01-11 10:25:09 +11:00
James Bielman ab37f833db MS5611: Fix CONFIG_MS5611_SERIAL definitions. 
- Make sure the values are defined as integers.  We were always using
  SPI rather than using I2C when desired.
 2013-01-09 11:19:51 -08:00
Andrew Tridgell 38f56be2c4 Plane: enable hardware sensors on PX4 2013-01-04 21:07:56 +11:00
James Bielman 264db3670e AP_Baro: Add CONFIG_MS5611_SERIAL option to choose between SPI and I2C. 
- Update ArduCopter and ArduPlane modules to pass the correct serial
  driver to the MS5611 driver.
- Update barometer examples, assuming SPI.
 2013-01-03 13:48:06 -08:00
Andrew Tridgell 4cdb3cd390 Plane: use GRAVITY_MSS 2013-01-02 14:45:08 +11:00
Andrew Tridgell 1a49549e3e Plane: start port of main ArduPlane code to AP_HAL_PX4 2013-01-02 14:45:08 +11:00
Andrew Tridgell b6295c12e1 Plane: fixes for new AP_Relay interface 2013-01-02 10:18:45 +11:00
Craig@3DR 0ed25cf719 Global change all references from 
GPS_PROTOCOL_MTK16
to
GPS_PROTOCOL_MTK19
 2013-01-02 09:24:31 +11:00
Andrew Tridgell edad43611d Plane: reset last heartbeat time on startup completion 
this gives more time for the GCS to send its first heartbeat
 2012-12-26 08:46:36 +11:00
Andrew Tridgell d54c6989ab Plane: fixed the last build warnings 
we now build with no warnings for APM1, APM2 and SITL. Yay!
 2012-12-20 22:46:48 +11:00
Andrew Tridgell feca411943 Plane: added new TRAINING mode 
this mode gives manual control when the roll or pitch is within the
set limits (the same limits as FBW mode), and prevents the pilot from
flying beyond those limits, essentially a "attitude limited manual"
mode
 2012-12-20 22:41:58 +11:00
Andrew Tridgell 9a2e77b797 Plane: fully disable relay and mount code on APM1-1280 
this saves some more flash space
 2012-12-20 14:53:23 +11:00
Andrew Tridgell cf18534163 Plane: use new functions 2012-12-20 14:53:22 +11:00
Andrew Tridgell 62d7fd1a26 Plane: fixed HIL builds 2012-12-20 14:52:37 +11:00
Andrew Tridgell 761ab5c3e8 Plane: use AP_HAL_BOARD_DRIVER 2012-12-20 14:52:33 +11:00
Andrew Tridgell 73f70cc596 Plane: moved to new GPS init syntax 2012-12-20 14:52:32 +11:00
Andrew Tridgell 678947c65d Plane: more fixes for SITL and new AP_Param startup 2012-12-20 14:52:29 +11:00
Andrew Tridgell e82deca305 Plane: updates to support AP_HAL SITL 2012-12-20 14:51:40 +11:00
Pat Hickey f8dec9ae4a ArduPlane: fixes to use CONFIG_HAL_BOARD instead of CONFIG_APM_HARDWARE 2012-12-20 14:51:37 +11:00
Pat Hickey a14621534c ArduPlane: port from hal.dataflash to old DataFlash api 2012-12-20 14:51:36 +11:00
Pat Hickey 92b0c302f2 ArduPlane: Ported to AP_HAL 2012-12-20 14:51:36 +11:00
Pat Hickey a4f1f6a5db AP_Progmem: fix dependencies for all sketches touched by AP_HAL_AVR 2012-12-20 14:51:28 +11:00
Pat Hickey 3f1d9d7f69 AP_Param: #include <AP_Param.h> fixups for libraries & sketches 
* I mostly went through with grep and added an #include <AP_Param.h> below
  every #include <AP_Common.h>. Not all of these example sketches might
  strictly need AP_Param.
 2012-12-20 14:51:19 +11:00
Andrew Tridgell e4949291e5 Plane: preparing for 2.68 release 2012-12-04 11:24:24 +11:00
Andrew Tridgell 805a340350 Plane: enable attitude and raw logging in HIL modes 2012-12-04 11:13:33 +11:00
Andrew Tridgell 24e1af1c82 Plane: fixed sensors and attitude HIL 
we now use the Stub version of the InertialSensor driver. In sensors
HIL we can now correctly drive the AHRS code.
 2012-12-03 23:26:39 +11:00
Andrew Tridgell 1104287aa2 Plane: use enum FlightMode in more places 2012-12-01 08:15:48 +11:00
Andrew Tridgell a6d8dbeac2 Plane: update ArduPlane for new ins interface 2012-11-30 07:15:18 +11:00
Andrew Tridgell f8a95e4084 APM: preparing for 2.67 release 2012-11-21 22:28:30 +11:00
Andrew Tridgell 84300c85d6 APM: make it possible to run the CLI on any serial port 2012-11-21 21:41:34 +11:00
rmackay9 2df7a407da ArduPlane: fix HIL build 2012-11-07 21:23:07 +09:00
rmackay9 ef727bbb3c ArduPlane: move to use new INS library instead of IMU library 2012-11-07 19:21:03 +09:00
Andrew Tridgell 8652bfee8d APM: added RSSI_PIN option for receiver RSSI 
this allows you to configure the pin for receiver RSSI without
recompiling
 2012-11-06 22:04:41 +11:00
Andrew Tridgell aa236c43f8 APM: prepare for 2.66 2012-10-31 13:25:19 +11:00
Pat Hickey d4bb8a10d7 Update ArduCopter and ArduPlane dependencies on AP_Menu 2012-10-18 20:53:39 -07:00
rmackay9 f695db61ea ArduPlane: added AP_Semaphore.h to list of includes 2012-10-06 13:14:28 +09:00
rmackay9 41fbb19cf5 AP_InertialSensor_MPU6000: replaced _cs_pin parameter with #define and saved 1 byte of memory 
Updated ArduCopter, ArduPlane and example sketches in AP_InertialSensor, AP_IMU and AP_AHRS libraries because they no longer need to pass in cs_pin to the constructor
 2012-09-28 19:21:59 +09:00
Andrew Tridgell 51aeb2dd4c APM: prepare for 2.65 2012-09-24 07:14:30 +10:00
Andrew Tridgell a4c3c5973d APM: prepare for 2.64 release 2012-09-23 19:32:56 +10:00
Andrew Tridgell cebb67e1df APM: removed the unused sonar code 
when we start supporting a sonar we'll add a AP_Sonar library, like
AP_Airspeed
 2012-09-19 19:35:22 +10:00
Andrew Tridgell 2324997e16 APM: added ALT_OFFSET parameter 
useful to adjust for barometric pressure changes during a long flight
 2012-09-19 16:23:25 +10:00
Andrew Tridgell 37cb56f3e1 APM: save another few bytes 2012-09-18 13:58:50 +10:00
Andrew Tridgell df962d25a8 APM: fixed a comment 2012-09-18 13:58:49 +10:00
Andrew Tridgell 12dc2e79cf APM: save 100 bytes of memory 
remove flight_mode_strings array
 2012-09-18 13:58:49 +10:00
Andrew Tridgell 86face0a03 APM: preparing for 2.63 release 2012-09-17 17:32:13 +10:00
Andrew Tridgell 7e8ef0ae95 APM: fixed handling of DO_REPEAT_SERVO and DO_REPEAT_RELAY 2012-09-17 14:45:47 +10:00
Andrew Tridgell b55e7903aa APM: prepare for 2.62 release 2012-09-13 12:02:18 +10:00
Andrew Tridgell b1408008c9 APM: allow for landing pitch control until final stage 2012-09-12 13:09:16 +10:00
Andrew Tridgell 05e72c6e68 APM: fixed roll in landing approach 2012-09-12 11:53:17 +10:00
Andrew Tridgell 5f3ffe4839 APM: switch to Randys new IMU rate control method 
this drives the speed of the 50Hz loop by the number of samples
accumulated in the IMU. This should give much more consistent timing
in DCM.

Thanks to Randy for introducing this scheme in ArduCopter!
 2012-09-11 16:39:36 +10:00
Andrew Tridgell 7e672628ea APM: removed the GPS_enabled flag 
this fixes using GPS_PROTOCOL to specify a specific GPS with a GPS
that takes a few updates before it works (eg. needing baud rate
changes).

This makes it easier to use an APM1-1280 with more features enabled
 2012-09-11 13:37:34 +10:00
Andrew Tridgell cb88681914 APM: added support for MAV_CMD_PREFLIGHT_REBOOT_SHUTDOWN 
this allows for remote reboot of APM
 2012-09-10 11:42:30 +10:00
Andrew Tridgell 657dd5969f APM: preparing for 2.61 release 2012-09-08 18:36:17 +10:00
Andrew Tridgell dec12c7370 APM: use ahrs.airspeed_estimate() in two more places 
this applies the wind constraint
 2012-09-08 11:37:11 +10:00
Andrew Tridgell 164c60d25f APM: added RUDDER_STEER option 
when enabled, this uses only the rudder to steer during takeoff and
landing, using aileron only for levelling
 2012-09-08 10:07:03 +10:00
Andrew Tridgell 68705fe7e6 APM: accumulate mag readings during spare cycles in ArduPlane 
With this change we average over 100 mag readings per compass.read()
call, which means we are reading the compass at over 1kHz instead of
10Hz. The noise reduction is huge.
 2012-09-08 10:05:58 +10:00
Andrew Tridgell 83153eebd4 APM: obey pitch limits in FBWA as well 
this means pitch limits are constrained by LIM_PITCH_MIN and
LIM_PITCH_MAX
 2012-08-30 20:15:42 +10:00
Andrew Tridgell e2b8817a89 APM: added the ability to forcibly crash the plane on OBC failsafe breach 
this allows a user to setup the OBC failsafe system to forcibly crash
the plane (surfaces at limits, zero throttle) when the failsafe system
triggers. This is to allow APM to be used in the Outback Challenge. In
the OBC an external failsafe board also does this using the heartbeat
control pin, so this is an extra safety mechanism.

To prevent users accidentially triggering a crash, this code only
activates if FS_TERM_ACTION is set to to the magic value 42.
 2012-08-28 20:18:24 +10:00
Andrew Tridgell fce01464b1 APM: added ALT_CTRL_ALG parameter 
this allows you to select different altitude control algorithms. The
current choices are for the default (automatic based on if airspeed is
available), or to force a non-airspeed algorithm

The idea is to make it possible to use airspeed for some things (like
wind speed, speed scaling) but not for alt control
 2012-08-28 20:18:24 +10:00
Andrew Tridgell dcbd0fbd44 APM: cleanup throttle suppression code and don't use airspeed to unsupress 
this removes the throttle suppression when any of the conditions are
met once, as otherwise flying slow below 10m could zero the throttle.

It also removes the use of airspeed for disabling throttle
supression. Otherwise a strong gust of wind can cause ArduPlane to
try to takeoff!
 2012-08-28 20:18:23 +10:00
Andrew Tridgell c730d9072e APM: prepare for ArduPlane 2.60 2012-08-22 16:28:38 +10:00
Andrew Tridgell 2d8f99433c APM: removed factor of 0.5 in non-airspeed takeoff pitch 
this limited the pitch far below the specified target pitch
 2012-08-22 16:28:38 +10:00
Andrew Tridgell 6ab2a861f7 APM: added RSSI to RC_CHANNELS_RAW as well 
and prevent double read
 2012-08-22 13:58:25 +10:00
Andrew Tridgell c0c0b8c976 APM: added RECEIVER_RSSI_PIN option 
this allows for the receiver RSSI to be sent over MAVLink

Thanks to Burt Green for the suggestion
 2012-08-22 13:33:12 +10:00
Andrew Tridgell 9e926eae51 APM: optional build with new controller libs 2012-08-22 12:39:07 +10:00
uncrustify 0e8a76ccdd uncrustify ArduPlane/ArduPlane.pde 2012-08-21 19:19:51 -07:00
Andrew Tridgell 343f7d2de0 APM: removed DMP support from ArduPlane 
Without centripetal correction the DMP code will almost certainly
crash a plane
 2012-08-22 11:46:35 +10:00
Andrew Tridgell 6d11940ada AHRS: removed Quaternion build support from APM/ACM/rover 2012-08-22 10:42:21 +10:00
rmackay9 6d489947cf ArduPlane: replaced many "int" with "int16_t", "long" with "int32_t" 2012-08-18 18:26:13 +09:00
Andrew Tridgell 5e690d5680 APM: added parameter FBWB_ELEV_REV 
this fixes issue 343
 2012-08-17 15:04:53 +10:00
Andrew Tridgell df3c8a5bc0 APM: when land_complete is true, use land_pitch 
this gives a flare on final landing
 2012-08-15 12:39:35 +10:00
Andrew Tridgell 47be6d8ad1 AP_Airspeed: remove airspeed filter and run at 10Hz 
this saves on the filter memory, and gives just as good a result
 2012-08-15 12:39:35 +10:00
Andrew Tridgell 8cb55eb75a APM: keep the time of the last heartbeat message 
this will be used for failsafe processing
 2012-08-15 12:39:34 +10:00
Andrew Tridgell 2865434d02 APM: added 'OBC' failsafe module for ArduPlane 
this adds FS_* parameters for setting up APM to follow the outback
challenge failsafe rules.

This includes:

 - manual pin
 - heartbeat pin
 - waypoint for heartbeat failure
 - waypoint for GPS failure
 2012-08-15 12:39:34 +10:00
Andrew Tridgell 93f1d5645b APM: fixed LOITER_TIME and LOITER_TURNS 
These now follow the mavlink spec. Loiter time is in seconds, and
loiter turns is now 32 bit angle, so can handle larger numbers of
turns.
 2012-08-15 12:39:34 +10:00
Andrew Tridgell d9b09d2c93 APM: allow for navigation by dead-reckoning 
we now ask AHRS if we have a position estimate, and use that if
available
 2012-08-11 12:01:08 +10:00
Amilcar Lucas d34549f386 Add an optional second mount to ArduPlane and ArduCopter 2012-08-08 23:22:24 +02:00
Andrew Tridgell dcc50b5705 AP_Airspeed: removed values passed to constructor 2012-08-08 16:38:39 +10:00
Andrew Tridgell 5bfd1200d6 APM: change variables to use _cm, _cd and _ms suffix for units 
this makes it less likely that we mix up units
 2012-08-08 12:12:30 +10:00
Andrew Tridgell a823c9ceae APM: removed cli slider and dipswitch options 
use mavlink/eeprom for all config
 2012-08-08 12:12:29 +10:00
Andrew Tridgell 12cd6b68ff AP_Param: update ArduPlane core for new AP_Param interface 2012-08-08 12:11:57 +10:00
Amilcar Lucas f14237126a Add me :) 2012-08-06 00:40:12 +02:00
Amilcar Lucas b8c7b8a786 RC_Channel: Allow each channel to know who they are, this simplifies the enabling and output function calls. 2012-08-05 23:08:31 +02:00
Amilcar Lucas 4ba847c449 The mount type must be updated periodically 2012-08-04 18:44:08 +02:00
Andrew Tridgell 301ab00c5b APM: added control switch debouncer 
this adds a switch debouncer, similar to the one used in
ArduCopter. I'm adding this after a flight on the weekend where noise
on the control mode channel caused a mode change away from auto.

To prevent this change adding excessive mode switch latency, it also
moves the reading of the control switch to the 10Hz loop, away from
the 3.3Hz loop. That gives us 0.2s delay in mode switch changes and
allows for spikes in the control mode for 0.1 seconds without changing
mode.
 2012-08-01 13:59:37 +10:00
rmackay9 06e35820e5 ArduPlane: allow MPU6000's DMP to be used for attitude estimation. 
Enable by adding this line to APM_Config.h:
#define DMP_ENABLED ENABLED
 2012-07-28 19:50:40 +09:00
Andrew Tridgell 9eb05a2e1a APM: update version for 2.50 release 2012-07-26 11:36:17 +10:00
Andrew Tridgell 7e697e4abd APM: switch back to old nav_roll calculation 
the old nav_roll will be used for the 2.50 release to prevent the need
for re-tuning. For the release after that we will use the new
calculation
 2012-07-26 10:03:36 +10:00
Michael Oborne 39ad8b5eec AP fix sitl hil attitude mode. 2012-07-24 07:18:25 +08:00
Jeff Taylor d02655ac56 APM: Fixed bug where landing_pitch wasnt initialized properly 
this adds a new LAND_PITCH_CD parameter to control the landing pitch
when an airspeed sensor is not being used
 2012-07-19 13:59:30 +10:00
Andrew Tridgell d6e370886f APM: rename airspeed_cruise to airspeed_cruise_cm to make the units clearer 
it is in cm/s, not m/s
 2012-07-19 11:50:41 +10:00
Amilcar Lucas 610fdeacc1 Support up to 11 servos in APM2 
Conflicts:

	ArduPlane/ArduPlane.pde
 2012-07-18 22:01:19 +02:00
Andrew Tridgell de3c9ce56d Airspeed: change APM to use new AP_Airspeed library 
the next step is AHRS dead reckoning
 2012-07-16 11:21:50 +10:00
Andrew Tridgell c80a88766f APM: added credit for FBW altitude limit code 
thanks Yuri!
 2012-07-10 08:36:50 +10:00
Andrew Tridgell f6d7d1bc59 APM: changed PID library to do automatic deltat calculation 
this fixes a problem with the HDNG2RLL PID, which was using the wrong
time base and prevents similar bugs from happening in the future
 2012-07-06 19:59:18 +10:00
Andrew Tridgell 58fd91165f APM: fixed some build warnings and type errors 2012-07-06 19:59:18 +10:00
Andrew Tridgell 6ee9f1ae97 APM: use new location functions 2012-07-04 12:42:46 +10:00
Andrew Tridgell 99b11e4f19 Mount: enable mount control via eeprom parameters 
this enables MNT_* parameter control of the camera mount code. It also
fixes the conversion of calculated angles between degrees and
integers, and fixes stabilised mount control when yaw control is not
available.
 2012-07-03 10:21:01 +10:00
Andrew Tridgell 55092c25a6 SITL: enable the SIM_* parameters in ArduCopter and ArduPlane 2012-06-29 15:10:52 +10:00
Andrew Tridgell 3a2594fa1a APM: ArduPlane updates for new compass interface 2012-06-27 16:01:50 +10:00
Andrew Tridgell 6639294c72 APM: update for new barometer interface 
the barometer can now calibrate and return altitude values.

A 0.3 low pass filter is used on altitude to match the previous code
 2012-06-27 16:01:50 +10:00
Andrew Tridgell 4a50686c3e APM: prepare for 2.40 release 2012-06-16 10:11:26 +10:00
Amilcar Lucas 1906e06b69 Added camera trigger functionality 2012-06-13 21:00:20 +02:00
Amilcar Lucas a32b7c200b Add "3 axis camera stabilization" and "point camera to 3D point" functionality 
Patch by Gregory Fletcher and reviewed by me
 2012-06-13 20:55:19 +02:00
Amilcar Lucas 5ffd489d87 Spellcheck 2012-06-13 20:44:35 +02:00
Jason Short c804860243 Cosmetic changes only. 2012-06-10 13:10:07 -07:00
Andrew Tridgell 99b39aef93 APM: ready for 2.40-beta 2012-06-08 18:03:21 +10:00
Andrew Tridgell 25c17a5425 re-enable the AP_Mount build 2012-06-04 19:32:11 +10:00
Andrew Tridgell 3af29bd84e AP_Mount: disable AP_Mount until it works with MAVLINK10 2012-06-04 13:14:51 +10:00
Andrew Tridgell b3aa704c49 AirSpeed: added parameter ARSPD_USE 
setting ARSPD_ENABLE to 1 and ARSPD_USE to 0 allows the airspeed
sensor to be initialised and logged without it being used for flight
control. This is very useful when initially testing an airspeed sensor
in a new plane. It also makes it possible to enable/disable the use of
the airspeed sensor during a flight at any time.
 2012-05-22 20:02:23 +10:00
Andrew Tridgell 3ae1c6f9e0 APM: prepare for 2.34 2012-05-14 14:29:59 +10:00
Andrew Tridgell f43f5900bc Telemetry: make it possible to use UART2 on APM2 
building with TELEMETRY_UART2=ENABLED allows you to use the solder
bridge on the APM2 to enable telemetry on UART2. This allows both USB
telemetry and a radio at the same time.
 2012-05-04 10:39:44 +10:00
Andrew Tridgell b6a475f6a5 MAVLink: make APM build with MAVLink 1.0 possible with arduino GUI 2012-04-24 22:24:58 +10:00
Andrew Tridgell 85ba978a65 ready for 2.33 release 2012-04-09 18:16:49 +10:00
Andrew Tridgell 7b50724f60 MAVLink: allow for find grained stream rate control 
streams can now be requested at any multiple of 20ms. So if you ask
for a stream at 7Hz then you will get it at close to 7Hz.
 2012-04-02 11:18:53 +10:00
Andrew Tridgell 86cc7a5e1d APM: enable AP_Declination by default 2012-03-30 14:25:27 +11:00
Andrew Tridgell 9d193f06c9 APM: Change version to 2.32 2012-03-29 12:50:12 +11:00
Andrew Tridgell 1c934dc7ef APM: increase ArduPlane version to 2.31 2012-03-27 16:13:29 +11:00
Andrew Tridgell 989304fb47 APM: enable the new offset nulling in APM 2012-03-27 15:37:24 +11:00
Andrew Tridgell 8afd196907 APM: adapt ArduPlane for AHRS framework 2012-03-19 17:29:02 +11:00
Michael Oborne 3944c1e665 update AP version to 2.30 2012-03-18 10:27:49 +08:00
Andrew Tridgell 2a03a0584f AP_Declination: disable library when AUTOMATIC_DECLINATION is not ENABLED 
unfortunately this library was causing avrdude to fail to load the hex
to my APM2. Until we work out why, it's disabled.
 2012-03-11 21:46:41 +11:00
Adam M Rivera d3667faef4 AP_Declination: Added call to compass.set_initial_location if the compass is enabled when the 3D fix is obtained. 
Signed-off-by: Andrew Tridgell <tridge@samba.org>
 2012-03-11 20:59:47 +11:00
Andrew Tridgell 371677610d APM: avoid fetching the DCM matrix twice 
also no special case for quaternions
 2012-03-10 10:34:32 +11:00
Andrew Tridgell e39c3cb9d2 APM: make it possible to build ArduPlane with quaternion support 2012-03-10 10:34:29 +11:00
rmackay9 02cf07bb6b ArduPlane - updated to use new filter library 2012-02-28 21:03:04 +09:00
rmackay9 e1114bf7f7 ArduPlane - added Filter.h to unbreak the build! 2012-02-26 17:05:56 +09:00
rmackay9 21d7a77009 ArduPlane - switch sonar to use new mode filter from filter library 2012-02-26 15:35:42 +09:00
Andrew Tridgell 0248b48d30 allow MAG_ENABLE to be changed in flight 
this disables the compass in DCM if MAG_ENABLE is changed in
flight. Without this we would use a fixed yaw once the compass is
disabled

This also makes sure we don't pass the compass to DCM till we have
done a read. This ensures we have a good compass fix for the initial
DCM heading
 2012-02-25 14:51:09 +11:00
Andrew Tridgell 330ff5dc8b APM: added some comments related to hold_course 
hold_course is either -1 (for disabled) or a course to hold for
takeoff/landing. This makes the code a bit clearer.

It also resets hold_course in all non-auto modes, to ensure it isn't
used
 2012-02-15 08:50:45 +11:00
Andrew Tridgell bc0ed62aa9 adapt mainline APM code to AP_Param 2012-02-13 16:22:51 +11:00
Michael Oborne 9ca6668c1b fix SITL attitude hil 2012-01-20 16:04:49 +08:00
analoguedevices 418f5ea31e Increment version number in anticipation of a firmware hex push. 2012-01-16 22:48:46 +00:00
Doug Weibel 797e0e27a9 Additional commenting on global variables 
First pass done.
 2012-01-16 10:28:03 -07:00
Doug Weibel b4e58b50ee Additional commenting on global variables 2012-01-16 09:45:42 -07:00
Doug Weibel 0306bf97a0 Just a little more commenting work on global variables 2012-01-15 16:11:02 -07:00
Doug Weibel 69c7598db2 Update battery monitoring code for ArduPlane 
Fixes compatibility for APM2.  Also a significant update to the battery monitoring code:  We previously had monitoring modes for individual cell voltages for 3 and 4 cell lipos.  These have been removed as they were never really supported (the cell voltages were computed but were not reported or recorded anywhere).  Also, some clean-up/prep work was done for supporting monitoring 2 separate battery packs.  The CLI battery and current monitoring tests were consolidated into 1 test.
 2012-01-15 16:10:28 -07:00
Doug Weibel 892f24ac5c Adding comments for global variables 2012-01-11 12:37:43 -07:00
Doug Weibel 4de2155845 Tweak to FBW min altitude 
Patch from Yury
 2011-12-31 15:44:40 -07:00
Andrew Tridgell cd3729d993 APM: added error checking on barometer read 
if the barometer is dead and the GPS has a fix, use the GPS for
altitude
 2011-12-28 20:41:53 +11:00
Andrew Tridgell 98353b7ba8 APM: added error checking on compass read 2011-12-28 20:41:53 +11:00
Andrew Tridgell 3cb96fb8af APM: convert to new I2C library 2011-12-28 20:41:53 +11:00