ardupilot/ArduCopter/config.h

646 lines
19 KiB
C
Raw Normal View History

//
#pragma once
//////////////////////////////////////////////////////////////////////////////
//////////////////////////////////////////////////////////////////////////////
//
// WARNING WARNING WARNING WARNING WARNING WARNING WARNING WARNING WARNING
//
// DO NOT EDIT this file to adjust your configuration. Create your own
// APM_Config.h and use APM_Config.h.example as a reference.
//
// WARNING WARNING WARNING WARNING WARNING WARNING WARNING WARNING WARNING
///
//////////////////////////////////////////////////////////////////////////////
//////////////////////////////////////////////////////////////////////////////
//
// Default and automatic configuration details.
//
// Notes for maintainers:
//
// - Try to keep this file organised in the same order as APM_Config.h.example
//
#include "defines.h"
///
/// DO NOT EDIT THIS INCLUDE - if you want to make a local change, make that
/// change in your local copy of APM_Config.h.
///
#include "APM_Config.h"
//////////////////////////////////////////////////////////////////////////////
//////////////////////////////////////////////////////////////////////////////
// HARDWARE CONFIGURATION AND CONNECTIONS
//////////////////////////////////////////////////////////////////////////////
//////////////////////////////////////////////////////////////////////////////
#ifndef CONFIG_HAL_BOARD
#error CONFIG_HAL_BOARD must be defined to build ArduCopter
#endif
//////////////////////////////////////////////////////////////////////////////
// HIL_MODE OPTIONAL
#ifndef HIL_MODE
#define HIL_MODE HIL_MODE_DISABLED
#endif
#define MAGNETOMETER ENABLED
// run at 400Hz on all systems
# define MAIN_LOOP_SECONDS 0.0025f
2014-02-25 18:40:29 -04:00
2016-01-21 22:59:47 -04:00
#ifndef ARMING_DELAY_SEC
# define ARMING_DELAY_SEC 2.0f
#endif
//////////////////////////////////////////////////////////////////////////////
// FRAME_CONFIG
//
#ifndef FRAME_CONFIG
# define FRAME_CONFIG MULTICOPTER_FRAME
#endif
2012-12-08 15:49:38 -04:00
/////////////////////////////////////////////////////////////////////////////////
2013-08-28 01:05:01 -03:00
// TradHeli defaults
2012-12-08 15:49:38 -04:00
#if FRAME_CONFIG == HELI_FRAME
# define RC_FAST_SPEED 125
# define WP_YAW_BEHAVIOR_DEFAULT WP_YAW_BEHAVIOR_LOOK_AHEAD
# define THR_MIN_DEFAULT 0
2014-02-02 03:58:36 -04:00
# define AUTOTUNE_ENABLED DISABLED
#endif
2012-12-08 15:49:38 -04:00
//////////////////////////////////////////////////////////////////////////////
// PWM control
// default RC speed in Hz
#ifndef RC_FAST_SPEED
2012-12-08 15:49:38 -04:00
# define RC_FAST_SPEED 490
#endif
//////////////////////////////////////////////////////////////////////////////
2016-04-27 08:37:04 -03:00
// Rangefinder
//
#ifndef RANGEFINDER_ENABLED
# define RANGEFINDER_ENABLED ENABLED
#endif
2016-04-27 08:37:04 -03:00
#ifndef RANGEFINDER_HEALTH_MAX
# define RANGEFINDER_HEALTH_MAX 3 // number of good reads that indicates a healthy rangefinder
#endif
2016-04-27 08:37:04 -03:00
#ifndef RANGEFINDER_GAIN_DEFAULT
# define RANGEFINDER_GAIN_DEFAULT 0.8f // gain for controlling how quickly rangefinder range adjusts target altitude (lower means slower reaction)
#endif
#ifndef THR_SURFACE_TRACKING_VELZ_MAX
2016-04-27 08:37:04 -03:00
# define THR_SURFACE_TRACKING_VELZ_MAX 150 // max vertical speed change while surface tracking with rangefinder
#endif
2016-04-27 08:37:04 -03:00
#ifndef RANGEFINDER_TIMEOUT_MS
# define RANGEFINDER_TIMEOUT_MS 1000 // desired rangefinder alt will reset to current rangefinder alt after this many milliseconds without a good rangefinder alt
#endif
#ifndef RANGEFINDER_WPNAV_FILT_HZ
# define RANGEFINDER_WPNAV_FILT_HZ 0.25f // filter frequency for rangefinder altitude provided to waypoint navigation class
#endif
2016-04-27 08:37:04 -03:00
#ifndef RANGEFINDER_TILT_CORRECTION // by disable tilt correction for use of range finder data by EKF
2016-04-28 00:32:46 -03:00
# define RANGEFINDER_TILT_CORRECTION ENABLED
#endif
#ifndef RANGEFINDER_GLITCH_ALT_CM
# define RANGEFINDER_GLITCH_ALT_CM 200 // amount of rangefinder change to be considered a glitch
#endif
#ifndef RANGEFINDER_GLITCH_NUM_SAMPLES
# define RANGEFINDER_GLITCH_NUM_SAMPLES 3 // number of rangefinder glitches in a row to take new reading
#endif
//////////////////////////////////////////////////////////////////////////////
// Proximity sensor
//
#ifndef PROXIMITY_ENABLED
# define PROXIMITY_ENABLED ENABLED
#endif
#ifndef MAV_SYSTEM_ID
2012-08-21 23:19:50 -03:00
# define MAV_SYSTEM_ID 1
#endif
//////////////////////////////////////////////////////////////////////////////
// Battery monitoring
//
2013-10-01 10:34:44 -03:00
#ifndef FS_BATT_VOLTAGE_DEFAULT
# define FS_BATT_VOLTAGE_DEFAULT 10.5f // default battery voltage below which failsafe will be triggered
#endif
2013-10-01 10:34:44 -03:00
#ifndef FS_BATT_MAH_DEFAULT
# define FS_BATT_MAH_DEFAULT 0 // default battery capacity (in mah) below which failsafe will be triggered
2011-09-18 21:12:28 -03:00
#endif
#ifndef BOARD_VOLTAGE_MIN
# define BOARD_VOLTAGE_MIN 4.3f // min board voltage in volts for pre-arm checks
#endif
#ifndef BOARD_VOLTAGE_MAX
# define BOARD_VOLTAGE_MAX 5.8f // max board voltage in volts for pre-arm checks
#endif
// prearm GPS hdop check
2013-08-15 01:04:43 -03:00
#ifndef GPS_HDOP_GOOD_DEFAULT
# define GPS_HDOP_GOOD_DEFAULT 140 // minimum hdop that represents a good position. used during pre-arm checks if fence is enabled
2013-08-15 01:04:43 -03:00
#endif
2013-04-29 09:30:22 -03:00
// GCS failsafe
#ifndef FS_GCS
# define FS_GCS DISABLED
#endif
#ifndef FS_GCS_TIMEOUT_MS
# define FS_GCS_TIMEOUT_MS 5000 // gcs failsafe triggers after 5 seconds with no GCS heartbeat
#endif
// Radio failsafe while using RC_override
#ifndef FS_RADIO_RC_OVERRIDE_TIMEOUT_MS
# define FS_RADIO_RC_OVERRIDE_TIMEOUT_MS 1000 // RC Radio failsafe triggers after 1 second while using RC_override from ground station
#endif
// Radio failsafe
#ifndef FS_RADIO_TIMEOUT_MS
#define FS_RADIO_TIMEOUT_MS 500 // RC Radio Failsafe triggers after 500 miliseconds with No RC Input
#endif
2016-04-22 08:37:48 -03:00
// missing terrain data failsafe
#ifndef FS_TERRAIN_TIMEOUT_MS
#define FS_TERRAIN_TIMEOUT_MS 5000 // 5 seconds of missing terrain data will trigger failsafe (RTL)
#endif
#ifndef PREARM_DISPLAY_PERIOD
# define PREARM_DISPLAY_PERIOD 30
#endif
// pre-arm baro vs inertial nav max alt disparity
#ifndef PREARM_MAX_ALT_DISPARITY_CM
# define PREARM_MAX_ALT_DISPARITY_CM 100 // barometer and inertial nav altitude must be within this many centimeters
#endif
2014-07-21 07:07:15 -03:00
//////////////////////////////////////////////////////////////////////////////
// EKF Failsafe
#ifndef FS_EKF_ACTION_DEFAULT
# define FS_EKF_ACTION_DEFAULT FS_EKF_ACTION_LAND // EKF failsafe triggers land by default
#endif
#ifndef FS_EKF_THRESHOLD_DEFAULT
# define FS_EKF_THRESHOLD_DEFAULT 0.8f // EKF failsafe's default compass and velocity variance threshold above which the EKF failsafe will be triggered
2014-07-21 07:07:15 -03:00
#endif
#ifndef EKF_ORIGIN_MAX_DIST_M
# define EKF_ORIGIN_MAX_DIST_M 50000 // EKF origin and waypoints (including home) must be within 50km
#endif
//////////////////////////////////////////////////////////////////////////////
// MAGNETOMETER
#ifndef MAGNETOMETER
2012-08-21 23:19:50 -03:00
# define MAGNETOMETER ENABLED
#endif
#ifndef COMPASS_CAL_STICK_GESTURE_TIME
#define COMPASS_CAL_STICK_GESTURE_TIME 2.0f // 2 seconds
#endif
#ifndef COMPASS_CAL_STICK_DELAY
#define COMPASS_CAL_STICK_DELAY 5.0f
#endif
//////////////////////////////////////////////////////////////////////////////
2017-03-01 07:18:11 -04:00
// OPTICAL_FLOW & VISUAL ODOMETRY
#ifndef OPTFLOW
# define OPTFLOW ENABLED
#endif
2017-03-01 07:18:11 -04:00
#ifndef VISUAL_ODOMETRY_ENABLED
# define VISUAL_ODOMETRY_ENABLED ENABLED
#endif
//////////////////////////////////////////////////////////////////////////////
// Auto Tuning
2014-02-02 03:58:36 -04:00
#ifndef AUTOTUNE_ENABLED
# define AUTOTUNE_ENABLED ENABLED
#endif
2013-08-04 11:20:21 -03:00
//////////////////////////////////////////////////////////////////////////////
// Crop Sprayer
#ifndef SPRAYER
# define SPRAYER ENABLED
2013-08-04 11:20:21 -03:00
#endif
//////////////////////////////////////////////////////////////////////////////
// Precision Landing with companion computer or IRLock sensor
#ifndef PRECISION_LANDING
# define PRECISION_LANDING ENABLED
#endif
2016-10-28 19:08:22 -03:00
//////////////////////////////////////////////////////////////////////////////
// gripper
#ifndef GRIPPER_ENABLED
# define GRIPPER_ENABLED ENABLED
#endif
2014-04-02 12:19:54 -03:00
//////////////////////////////////////////////////////////////////////////////
// Parachute release
#ifndef PARACHUTE
# define PARACHUTE ENABLED
2014-04-02 12:19:54 -03:00
#endif
2015-11-27 00:53:08 -04:00
//////////////////////////////////////////////////////////////////////////////
// ADSB support
#ifndef ADSB_ENABLED
# define ADSB_ENABLED ENABLED
#endif
//////////////////////////////////////////////////////////////////////////////
// Nav-Guided - allows external nav computer to control vehicle
#ifndef NAV_GUIDED
# define NAV_GUIDED ENABLED
#endif
//////////////////////////////////////////////////////////////////////////////
// RADIO CONFIGURATION
//////////////////////////////////////////////////////////////////////////////
//////////////////////////////////////////////////////////////////////////////
//////////////////////////////////////////////////////////////////////////////
// FLIGHT_MODE
//
#ifndef FLIGHT_MODE_1
2012-08-21 23:19:50 -03:00
# define FLIGHT_MODE_1 STABILIZE
#endif
#ifndef FLIGHT_MODE_2
2012-08-21 23:19:50 -03:00
# define FLIGHT_MODE_2 STABILIZE
#endif
#ifndef FLIGHT_MODE_3
2012-08-21 23:19:50 -03:00
# define FLIGHT_MODE_3 STABILIZE
#endif
#ifndef FLIGHT_MODE_4
2012-08-21 23:19:50 -03:00
# define FLIGHT_MODE_4 STABILIZE
#endif
#ifndef FLIGHT_MODE_5
2012-08-21 23:19:50 -03:00
# define FLIGHT_MODE_5 STABILIZE
#endif
#ifndef FLIGHT_MODE_6
2012-08-21 23:19:50 -03:00
# define FLIGHT_MODE_6 STABILIZE
#endif
//////////////////////////////////////////////////////////////////////////////
// Throttle Failsafe
//
#ifndef FS_THR_VALUE_DEFAULT
# define FS_THR_VALUE_DEFAULT 975
#endif
//////////////////////////////////////////////////////////////////////////////
// Takeoff
//
#ifndef PILOT_TKOFF_ALT_DEFAULT
# define PILOT_TKOFF_ALT_DEFAULT 0 // default final alt above home for pilot initiated takeoff
#endif
//////////////////////////////////////////////////////////////////////////////
// Landing
//
#ifndef LAND_SPEED
# define LAND_SPEED 50 // the descent speed for the final stage of landing in cm/s
#endif
#ifndef LAND_START_ALT
# define LAND_START_ALT 1000 // altitude in cm where land controller switches to slow rate of descent
#endif
#ifndef LAND_REPOSITION_DEFAULT
2014-08-30 22:44:09 -03:00
# define LAND_REPOSITION_DEFAULT 1 // by default the pilot can override roll/pitch during landing
#endif
#ifndef LAND_WITH_DELAY_MS
# define LAND_WITH_DELAY_MS 4000 // default delay (in milliseconds) when a land-with-delay is triggered during a failsafe event
#endif
#ifndef LAND_CANCEL_TRIGGER_THR
# define LAND_CANCEL_TRIGGER_THR 700 // land is cancelled by input throttle above 700
#endif
#ifndef LAND_RANGEFINDER_MIN_ALT_CM
#define LAND_RANGEFINDER_MIN_ALT_CM 200
#endif
//////////////////////////////////////////////////////////////////////////////
// Landing Detector
//
#ifndef LAND_DETECTOR_TRIGGER_SEC
# define LAND_DETECTOR_TRIGGER_SEC 1.0f // number of seconds to detect a landing
#endif
#ifndef LAND_DETECTOR_MAYBE_TRIGGER_SEC
# define LAND_DETECTOR_MAYBE_TRIGGER_SEC 0.2f // number of seconds that means we might be landed (used to reset horizontal position targets to prevent tipping over)
#endif
#ifndef LAND_DETECTOR_ACCEL_LPF_CUTOFF
# define LAND_DETECTOR_ACCEL_LPF_CUTOFF 1.0f // frequency cutoff of land detector accelerometer filter
#endif
#ifndef LAND_DETECTOR_ACCEL_MAX
# define LAND_DETECTOR_ACCEL_MAX 1.0f // vehicle acceleration must be under 1m/s/s
#endif
//////////////////////////////////////////////////////////////////////////////
// CAMERA TRIGGER AND CONTROL
//
#ifndef CAMERA
# define CAMERA ENABLED
#endif
//////////////////////////////////////////////////////////////////////////////
// MOUNT (ANTENNA OR CAMERA)
//
#ifndef MOUNT
# define MOUNT ENABLED
#endif
//////////////////////////////////////////////////////////////////////////////
2014-02-03 08:07:30 -04:00
// Flight mode definitions
//
// Acro Mode
2014-02-03 08:07:30 -04:00
#ifndef ACRO_RP_P
# define ACRO_RP_P 4.5f
#endif
2014-02-03 08:07:30 -04:00
#ifndef ACRO_YAW_P
# define ACRO_YAW_P 4.5f
#endif
2013-08-04 05:46:04 -03:00
#ifndef ACRO_LEVEL_MAX_ANGLE
# define ACRO_LEVEL_MAX_ANGLE 3000
#endif
2014-02-03 08:07:30 -04:00
#ifndef ACRO_BALANCE_ROLL
#define ACRO_BALANCE_ROLL 1.0f
#endif
2014-02-03 08:07:30 -04:00
#ifndef ACRO_BALANCE_PITCH
#define ACRO_BALANCE_PITCH 1.0f
#endif
#ifndef ACRO_RP_EXPO_DEFAULT
#define ACRO_RP_EXPO_DEFAULT 0.3f
#endif
#ifndef ACRO_Y_EXPO_DEFAULT
#define ACRO_Y_EXPO_DEFAULT 0.0f
#endif
#ifndef ACRO_THR_MID_DEFAULT
#define ACRO_THR_MID_DEFAULT 0.0f
2014-08-12 23:25:59 -03:00
#endif
2012-02-15 13:09:42 -04:00
// RTL Mode
#ifndef RTL_ALT_FINAL
2013-08-29 22:34:23 -03:00
# define RTL_ALT_FINAL 0 // the altitude the vehicle will move to as the final stage of Returning to Launch. Set to zero to land.
#endif
#ifndef RTL_ALT
# define RTL_ALT 1500 // default alt to return to home in cm, 0 = Maintain current altitude
2012-02-15 13:09:42 -04:00
#endif
#ifndef RTL_ALT_MIN
# define RTL_ALT_MIN 200 // min height above ground for RTL (i.e 2m)
#endif
#ifndef RTL_CLIMB_MIN_DEFAULT
# define RTL_CLIMB_MIN_DEFAULT 0 // vehicle will always climb this many cm as first stage of RTL
#endif
2016-01-06 03:00:29 -04:00
#ifndef RTL_ABS_MIN_CLIMB
# define RTL_ABS_MIN_CLIMB 250 // absolute minimum initial climb
2016-01-06 03:00:29 -04:00
#endif
#ifndef RTL_CONE_SLOPE_DEFAULT
# define RTL_CONE_SLOPE_DEFAULT 3.0f // slope of RTL cone (height / distance). 0 = No cone
2016-01-06 03:00:29 -04:00
#endif
#ifndef RTL_MIN_CONE_SLOPE
# define RTL_MIN_CONE_SLOPE 0.5f // minimum slope of cone
#endif
#ifndef RTL_LOITER_TIME
2016-05-12 14:24:23 -03:00
# define RTL_LOITER_TIME 5000 // Time (in milliseconds) to loiter above home before beginning final descent
2012-11-10 01:45:02 -04:00
#endif
2014-02-03 08:07:30 -04:00
// AUTO Mode
#ifndef WP_YAW_BEHAVIOR_DEFAULT
# define WP_YAW_BEHAVIOR_DEFAULT WP_YAW_BEHAVIOR_LOOK_AT_NEXT_WP_EXCEPT_RTL
#endif
2014-02-03 08:07:30 -04:00
#ifndef AUTO_YAW_SLEW_RATE
# define AUTO_YAW_SLEW_RATE 60 // degrees/sec
2011-10-27 15:55:13 -03:00
#endif
#ifndef YAW_LOOK_AHEAD_MIN_SPEED
# define YAW_LOOK_AHEAD_MIN_SPEED 100 // minimum ground speed in cm/s required before copter is aimed at ground course
#endif
2014-02-03 08:07:30 -04:00
// Super Simple mode
#ifndef SUPER_SIMPLE_RADIUS
# define SUPER_SIMPLE_RADIUS 1000
#endif
2011-10-27 15:55:13 -03:00
//////////////////////////////////////////////////////////////////////////////
// Stabilize Rate Control
//
#ifndef ROLL_PITCH_YAW_INPUT_MAX
# define ROLL_PITCH_YAW_INPUT_MAX 4500 // roll, pitch and yaw input range
#endif
#ifndef DEFAULT_ANGLE_MAX
# define DEFAULT_ANGLE_MAX 4500 // ANGLE_MAX parameters default value
#endif
#ifndef ANGLE_RATE_MAX
# define ANGLE_RATE_MAX 18000 // default maximum rotation rate in roll/pitch axis requested by angle controller used in stabilize, loiter, rtl, auto flight modes
#endif
2014-02-03 08:07:30 -04:00
//////////////////////////////////////////////////////////////////////////////
// Loiter position control gains
//
#ifndef POS_XY_P
# define POS_XY_P 1.0f
#endif
2015-04-22 18:10:30 -03:00
//////////////////////////////////////////////////////////////////////////////
// Stop mode defaults
//
2015-06-05 03:29:00 -03:00
#ifndef BRAKE_MODE_SPEED_Z
# define BRAKE_MODE_SPEED_Z 250 // z-axis speed in cm/s in Brake Mode
#endif
2015-05-17 00:22:20 -03:00
#ifndef BRAKE_MODE_DECEL_RATE
# define BRAKE_MODE_DECEL_RATE 750 // acceleration rate in cm/s/s in Brake Mode
2015-04-22 18:10:30 -03:00
#endif
2012-02-15 13:09:42 -04:00
//////////////////////////////////////////////////////////////////////////////
// Velocity (horizontal) gains
2012-02-15 13:09:42 -04:00
//
#ifndef VEL_XY_P
# define VEL_XY_P 1.0f
2012-02-15 13:09:42 -04:00
#endif
#ifndef VEL_XY_I
# define VEL_XY_I 0.5f
2012-02-15 13:09:42 -04:00
#endif
#ifndef VEL_XY_IMAX
# define VEL_XY_IMAX 1000
2012-02-15 13:09:42 -04:00
#endif
#ifndef VEL_XY_FILT_HZ
# define VEL_XY_FILT_HZ 5.0f
2015-03-03 23:47:05 -04:00
#endif
2012-02-15 13:09:42 -04:00
2014-04-11 05:15:09 -03:00
//////////////////////////////////////////////////////////////////////////////
2014-07-11 02:08:09 -03:00
// PosHold parameter defaults
2014-04-11 05:15:09 -03:00
//
2014-07-11 02:08:09 -03:00
#ifndef POSHOLD_ENABLED
# define POSHOLD_ENABLED ENABLED // PosHold flight mode enabled by default
#endif
2014-07-11 02:08:09 -03:00
#ifndef POSHOLD_BRAKE_RATE_DEFAULT
# define POSHOLD_BRAKE_RATE_DEFAULT 8 // default POSHOLD_BRAKE_RATE param value. Rotation rate during braking in deg/sec
2014-04-11 05:15:09 -03:00
#endif
2014-07-11 02:08:09 -03:00
#ifndef POSHOLD_BRAKE_ANGLE_DEFAULT
# define POSHOLD_BRAKE_ANGLE_DEFAULT 3000 // default POSHOLD_BRAKE_ANGLE param value. Max lean angle during braking in centi-degrees
2014-04-11 05:15:09 -03:00
#endif
//////////////////////////////////////////////////////////////////////////////
// Throttle control gains
//
#ifndef THR_DZ_DEFAULT
# define THR_DZ_DEFAULT 100 // the deadzone above and below mid throttle while in althold or loiter
#endif
#ifndef ALT_HOLD_P
# define ALT_HOLD_P 1.0f
#endif
// Velocity (vertical) control gains
#ifndef VEL_Z_P
# define VEL_Z_P 5.0f
#endif
// Accel (vertical) control gains
#ifndef ACCEL_Z_P
# define ACCEL_Z_P 0.50f
#endif
#ifndef ACCEL_Z_I
# define ACCEL_Z_I 1.00f
#endif
#ifndef ACCEL_Z_D
# define ACCEL_Z_D 0.0f
#endif
#ifndef ACCEL_Z_IMAX
# define ACCEL_Z_IMAX 800
#endif
#ifndef ACCEL_Z_FILT_HZ
# define ACCEL_Z_FILT_HZ 20.0f
2015-03-03 23:47:05 -04:00
#endif
// default maximum vertical velocity and acceleration the pilot may request
#ifndef PILOT_VELZ_MAX
# define PILOT_VELZ_MAX 250 // maximum vertical velocity in cm/s
#endif
#ifndef PILOT_ACCEL_Z_DEFAULT
# define PILOT_ACCEL_Z_DEFAULT 250 // vertical acceleration in cm/s/s while altitude is under pilot control
#endif
// max distance in cm above or below current location that will be used for the alt target when transitioning to alt-hold mode
#ifndef ALT_HOLD_INIT_MAX_OVERSHOOT
# define ALT_HOLD_INIT_MAX_OVERSHOOT 200
#endif
// the acceleration used to define the distance-velocity curve
#ifndef ALT_HOLD_ACCEL_MAX
# define ALT_HOLD_ACCEL_MAX 250 // if you change this you must also update the duplicate declaration in AC_WPNav.h
#endif
#ifndef AUTO_DISARMING_DELAY
# define AUTO_DISARMING_DELAY 10
#endif
//////////////////////////////////////////////////////////////////////////////
// Throw mode configuration
//
#ifndef THROW_HIGH_SPEED
# define THROW_HIGH_SPEED 500.0f // vehicle much reach this total 3D speed in cm/s (or be free falling)
#endif
#ifndef THROW_VERTICAL_SPEED
# define THROW_VERTICAL_SPEED 50.0f // motors start when vehicle reaches this total 3D speed in cm/s
#endif
//////////////////////////////////////////////////////////////////////////////
// Dataflash logging control
//
#ifndef LOGGING_ENABLED
2012-08-21 23:19:50 -03:00
# define LOGGING_ENABLED ENABLED
#endif
2015-03-13 03:25:08 -03:00
// Default logging bitmask
#ifndef DEFAULT_LOG_BITMASK
# define DEFAULT_LOG_BITMASK \
MASK_LOG_ATTITUDE_MED | \
MASK_LOG_GPS | \
MASK_LOG_PM | \
MASK_LOG_CTUN | \
MASK_LOG_NTUN | \
MASK_LOG_RCIN | \
MASK_LOG_IMU | \
MASK_LOG_CMD | \
MASK_LOG_CURRENT | \
MASK_LOG_RCOUT | \
2014-12-07 22:16:53 -04:00
MASK_LOG_OPTFLOW | \
MASK_LOG_COMPASS | \
MASK_LOG_CAMERA | \
MASK_LOG_MOTBATT
#endif
//////////////////////////////////////////////////////////////////////////////
// Fence, Rally and Terrain and AC_Avoidance defaults
//
2016-02-03 20:55:07 -04:00
// Enable/disable Fence
#ifndef AC_FENCE
#define AC_FENCE ENABLED
#endif
2014-04-06 22:18:43 -03:00
#ifndef AC_RALLY
#define AC_RALLY ENABLED
2014-04-06 22:18:43 -03:00
#endif
#ifndef AC_TERRAIN
#define AC_TERRAIN ENABLED
#endif
#if AC_TERRAIN && !AC_RALLY
#error Terrain relies on Rally which is disabled
#endif
#ifndef AC_AVOID_ENABLED
#define AC_AVOID_ENABLED ENABLED
#endif
#if AC_AVOID_ENABLED && !PROXIMITY_ENABLED
#error AC_Avoidance relies on PROXIMITY_ENABLED which is disabled
#endif
#if AC_AVOID_ENABLED && !AC_FENCE
#error AC_Avoidance relies on AC_FENCE which is disabled
#endif
//////////////////////////////////////////////////////////////////////////////
// Developer Items
//
//use this to completely disable FRSKY TELEM
#ifndef FRSKY_TELEM_ENABLED
# define FRSKY_TELEM_ENABLED ENABLED
#endif
#ifndef ADVANCED_FAILSAFE
2016-08-25 10:22:10 -03:00
# define ADVANCED_FAILSAFE DISABLED
#endif