- vehicle_angular_velocity: ESC RPM notch filters minimize filter resets
- only allow one filter init per axis per cycle
- "park" ESC notch filters at min frequency instead of full disable
- relax timeout before a notch filter is disabled
- add new parameter IMU_GYRO_DNF_MIN for configuring the minimum notch filter frequency
- new modules/simulation directory to collect all simulators and related modules
- new Tools/simulation directory to collect and organize scattered simulation submodules, scripts, etc
- simulation module renamed to simulator_mavlink
- sih renamed to simulator_sih (not a great name, but I wanted to be clear it was a simulator)
- ignition_simulator renamed to simulator_ignition_bridge
- large sitl_target.cmake split by simulation option and in some cases pushed to appropriate modules
- sitl targets broken down to what's actually available (eg jmavsim only has 1 model and 1 world)
- new Gazebo consistently referred to as Ignition for now (probably the least confusing thing until we fully drop Gazebo classic support someday)
- new static notch filter configured via IMU_GYRO_NF1_FRQ and IMU_GYRO_NF1_BW
- existing notch parameters IMU_GYRO_NF_FREQ and IMU_GYRO_NF_BW become
IMU_GYRO_NF0_FRQ and IMU_GYRO_NF0_BW
- when estimating the peak frequency the magnitude of side buckets will
be factored in, so it doesn't make sense to potentially treat them as
separatey detected peaks
- initial frequency peak tracking SNR increased from 10->15 db
- after initial detection the threshold decreases to SNR 5db
- gyro_fft large method refactored into smaller pieces
- sensors/vehicle_angular_velocity: dynamic notch FFT make sample rate
check a percentage and relax lower bound safety threshold
Using mixers on the IO side had a remote benefit of being able to
override all control surfaces with a radio remote on a fixed wing.
This ended up not being used that much and since the original design
10 years ago (2011) we have been able to convince ourselves that the
overall system stability is at a level where this marginal benefit,
which is not present on multicopters, is not worth the hazzle.
Co-authored-by: Beat Küng <beat-kueng@gmx.net>
Co-authored-by: Daniel Agar <daniel@agar.ca>
- change default FFT length (1024 -> 512)
- this doubles the update rate because half the number of samples are required for each
- decrease number of peaks (4 -> 3)
- so far 3 seems to be sufficient on most vehicles
- increase median filter window (3 -> 5)
- decrease SNR requirement (likely needs to be configurable)
- always check with state machine before reboot/shutdown
- respect BOARD_HAS_POWER_CONTROL (shutdown from command, low battery, power button)
- px4_shutdown_request add optional delay and always execute from HPWORK
- px4_shutdown_request split out px4_reboot_request
* MC_HTE: unitialize with hover_thrust parameter
* MC_HTE: constrain hover thrust setter between 0.1 and 0.9
* MC_HTE: integrate with land detector and velocity controller
* MCHoverThrustEstimator: Always publish an estimate even when not fusing measurements. This is required as the land detector and the position controller need to receive a hover thrust value.
* MC_HTE: use altitude agl threshold to start the estimator
local_position.z is relative to the origin of the EKF while dist_bottom
is above ground
Co-authored-by: bresch <brescianimathieu@gmail.com>
- this is one of the last pieces of the system that still depend on DriverFramework
- add new SIM_GPS_NOISE_X parameter for optionally increasing the GPS noise multiplier (was previously a gpssim command line option)
- add SIM_x_BLOCK parameters to block sensor publication
- SIM_GPS_BLOCK
- SIM_ACCEL_BLOCK
- SIM_GYRO_BLOCK
- SIM_MAG_BLOCK
- SIM_BARO_BLOCK
- SIM_DPRES_BLOCK
This new airspeed module does:
-runns an airspeed validator for every airspeed sensor present, which checks measurement validity and estimates an airspeed scale
-selects another airspeed sensor if for the current one a failure is detected
-estimates airspeed with groundspeed-windspeed if no valid airspeed sensor is present
-outputs airspeed_validated topic
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
- move posix-configs/SITL/init/{rcS,10016_iris,6011_typhoon_h480} to ROMFS/px4fmu_common/init.d-posix
allows for easier unification, only one symlink is required.
- rcS: add AUTOCNF support. Update scripts to match with behavior of PX4
master (parameter values, some sitl driver got removed)
- add alias to allow 'set variable value' syntax in scripts to px4-alias.sh
- use px4_getopt
- use separate argument for the test_data directory
- append PATH from within the px4 binary: this simplifies the usage
w/o the sitl_run.sh script.
- add 'source px4-alias.sh' to all existing sitl startup scripts
- move sitl mixers to ROMFS/px4fmu_common/mixers-sitl
makes it easier to use existing mixers and sitl-specific ones.
- remove unused rcS_gazebo_delta_wing
- move to ModuleBase
- strip down to PWM 8 and 16 modes only
- remove all dead code
- implement missing pwm ioctls (current value, rates, etc)
- default rate 50Hz -> 400Hz
Thomas Stastny
Konrad
Daniel Agar
garfieldG
Matthias Grob
Beat Küng
Silvan Fuhrer
Mara Bos