Peter Barker
9f556197a0
AP_Mount: use ins singleton
2018-03-16 00:37:35 -07:00
Peter Barker
f0d06e7a9c
AP_Arming: use ins singleton
2018-03-16 00:37:35 -07:00
Peter Barker
1dabcc473d
AP_AHRS: use ins singleton
2018-03-16 00:37:35 -07:00
Peter Barker
2749ee9060
Copter: use ins singleton
2018-03-16 00:37:35 -07:00
Peter Barker
7cc808543f
AC_Precland: use ins singleton
2018-03-16 00:37:35 -07:00
Randy Mackay
feecbe442f
Copter: use multiply instead of divide in param conversion
2018-03-16 13:50:57 +09:00
Randy Mackay
d0e6c4d08d
AC_WPNav: correct LOIT_MAXA param description
2018-03-16 13:50:57 +09:00
Randy Mackay
33f437a72c
AC_AttitudeControl: use multiply instead of divide
2018-03-16 13:50:57 +09:00
Randy Mackay
548a7f8fcf
Plane: add minor comment to quadplane
2018-03-16 13:50:57 +09:00
Leonard Hall
ee745d2cd2
Plane: quad plane uses rate-control control during transitions
2018-03-16 13:50:57 +09:00
Leonard Hall
c53ba22daa
AC_AttitudeControl: add new rate only attitude control
2018-03-16 13:50:57 +09:00
Leonard Hall
a16d4ddad7
Plane: quadplane uses poscontrol instead of loiter
2018-03-16 13:50:57 +09:00
Randy Mackay
d43341c532
Sub: run guided velocity control at main loop rate
2018-03-16 13:50:57 +09:00
Randy Mackay
d7ea8f073f
Copter: run guided velocity control at main loop rate
2018-03-16 13:50:57 +09:00
Randy Mackay
21abe1194e
AC_WPNav: run horizontal position control at main loop rate
2018-03-16 13:50:57 +09:00
Randy Mackay
e9c23b538e
AC_Circle: run horizontal position control at main loop rate
2018-03-16 13:50:57 +09:00
Randy Mackay
ac82a37728
AC_PosControl: run horiz control at main loop rate
2018-03-16 13:50:57 +09:00
Randy Mackay
9e0a57eec7
DataFlash: minor formatting fixes
...
non-functional change
2018-03-16 13:50:57 +09:00
Randy Mackay
c857f8332b
Sub: replace NTUN with PSC logging
2018-03-16 13:50:57 +09:00
Randy Mackay
4a74b1b5e5
Copter: replace NTUN with PSC logging
2018-03-16 13:50:57 +09:00
Randy Mackay
13007e2a07
AC_PosControl: dataflash logging of PSC message
2018-03-16 13:50:57 +09:00
Randy Mackay
c5d838125b
Plane: quadplane logs PSC message
2018-03-16 13:50:57 +09:00
Randy Mackay
5be1020578
AC_WPNav: use multiply instead of divide
...
non-functional change
2018-03-16 13:50:57 +09:00
Randy Mackay
69cfea4057
AC_PosControl: use float for local consts
2018-03-16 13:50:57 +09:00
Randy Mackay
b988a6ca08
AC_AttitudeControl: add units to INPUT_TC param desc
2018-03-16 13:50:57 +09:00
Randy Mackay
0392d2752d
Copter: tuning rc-feel uses multiply instead of divide
2018-03-16 13:50:57 +09:00
Randy Mackay
92b56c2c89
AC_WPNav: init_loiter_target always resets I term
...
This was only used by poshold and this has been removed as part of "new-loiter"
2018-03-16 13:50:57 +09:00
Randy Mackay
1035645f5c
Copter: poshold always resets loiter I term
2018-03-16 13:50:57 +09:00
Randy Mackay
09cad7c59d
Plane: quadplane integrates attitude control inertial_frame_reset
2018-03-16 13:50:57 +09:00
Randy Mackay
03c162432e
Plane: quadplane provides dt to AC_WPNav::set_pilot_desired_acceleration
2018-03-16 13:50:57 +09:00
Randy Mackay
a0a9a68fbc
Plane: quadplane smoothing gain replaced by Q_A_INPUT_TC
...
Q_A_INPUT_TC parameter allows this to be tuned and a single value (which defaults to a value between the two previously used values) is used for all modes
2018-03-16 13:50:57 +09:00
Leonard Hall
aa47b19dea
Plane: remove quadplane calls to multicopter poscontrol's freeze_ff_xy
2018-03-16 13:50:57 +09:00
Randy Mackay
01d1d41302
Sub: integrate attitude control inertial_frame_reset
2018-03-16 13:50:57 +09:00
Randy Mackay
2154d08185
Sub: remove setting of pos-con jerk
2018-03-16 13:50:57 +09:00
Randy Mackay
2697e19513
Sub: guided removes xy mode from calls to pos-con
...
Also always limit angle to maintain altitude
2018-03-16 13:50:57 +09:00
Randy Mackay
da17034a3d
Sub: replace smoothing gain with AC_AttitudeControl::set_input_tc
2018-03-16 13:50:57 +09:00
Leonard Hall
a727305a59
Copter: integrate attitude control EKF inertial-frame-reset
2018-03-16 13:50:57 +09:00
Randy Mackay
f368ff6664
Copter: parameter conversion from RC_FEEL_RP to ATC_INPUT_TC
2018-03-16 13:50:57 +09:00
Leonard Hall
8ac653cabf
Copter: AutoTune integrate renamed use_sqrt_controller
2018-03-16 13:50:57 +09:00
Randy Mackay
853d7ab573
Copter: remove setting of pos-con jerk
2018-03-16 13:50:57 +09:00
Leonard Hall
7511781a7e
Copter: add accel target to NTUN log msg
...
Also rename NTUN column headers from D (meaning Desired) to T (meaning Target)
2018-03-16 13:50:57 +09:00
Leonard Hall
f9acc8a666
Copter: guided removes xy mode in calls to pos-con
...
Also limit angle to hold altitude
2018-03-16 13:50:57 +09:00
Randy Mackay
1a0be015f9
Copter: land, loiter, rtl provide dt to AC_WPNav::set_pilot_desired_acceleration
...
Also fix accelerations/lean-angles for land and rtl-land
2018-03-16 13:50:57 +09:00
Leonard Hall
93de23e7c4
Copter: get-pilot-desired-lean-angles accepts another angle-max
2018-03-16 13:50:57 +09:00
Leonard Hall
1540f98888
Copter: add angle inputs to Loiter
2018-03-16 13:50:57 +09:00
Leonard Hall
9544b1763b
Copter: replace smoothing gain with AC_AttitudeControl::set_input_tc
2018-03-16 13:50:57 +09:00
Leonard Hall
a356cfa529
AC_Circle: init resets desired velocity_xy
2018-03-16 13:50:57 +09:00
Leonard Hall
d104e3a3c0
AC_Circle: remove xy mode and limit angle to maintain alt
2018-03-16 13:50:57 +09:00
Leonard Hall
1c0678226c
AC_WPNav: new loiter including accel ff and braking
...
Includes:
sanity check loiter accel max vs lean angle max
increase loiter aggressiveness
remove loiter calls to pos_con.freeze_ff_xy
use loiter max velocity correction
remove xy mode from loiter
move predictor to angle
add maximum pilot commanded angle to loiter
loiter use alt hold angle limit
set_pilot_desired_acceleration accept dt
Also includes:
remove loiter jerk and setting pos-con jerk
breaking gain is based on VelxyP
Jerk limit Loiter breaking
change breaking parameters use jerk limit
add maximum distance correction in Loiter to 2m
update Loiter parameter defaults
2018-03-16 13:50:57 +09:00
Leonard Hall
c7c3dd561a
AC_WPNav: brake, wp and spline clear desired velocity_xy
2018-03-16 13:50:57 +09:00
