Andrew Tridgell
fe3943e686
Plane: faster startup
...
make it less likely to send wrong INS_PRODUCT_ID, plus don't waste as
much time
2013-11-02 21:41:11 +11:00
Andrew Tridgell
035ac3800a
Plane: use G_Dt for acro angle integration
...
also cleanup some other uses of performance timing
2013-10-12 13:30:27 +11:00
Andrew Tridgell
eef693f243
Plane: removed some compat code
...
fixes warnings
2013-09-30 21:06:43 +10:00
Andrew Tridgell
444d053dc2
Plane: enable Oilpan and BMP085 on Linux
2013-09-29 01:02:05 +10:00
Andrew Tridgell
b28a4f21f2
Plane: fixed uartA baud rates for APM1
2013-09-21 09:30:29 +10:00
Andrew Tridgell
21a4da0d29
Plane: removed flash_leds() calls
2013-09-19 18:38:28 +10:00
Andrew Tridgell
4bd6b2f428
Plane: use new usb_connected() function
2013-09-19 16:23:58 +10:00
Andrew Tridgell
fe5a4ab710
Plane: fixed Vcc
2013-09-12 13:26:27 +10:00
Andrew Tridgell
f6688582a6
Plane: added FENCE_ACTION=3 behaviour
...
this makes it safer to enable the geofence as a receiver failsafe
mode. It retains manual throttle control, so if it triggers on the
ground due to the receiver losing signal from the transmitter then the
throttle can be kept low, preventing an unexpected takeoff.
2013-09-08 07:31:10 +10:00
Andrew Tridgell
4a8c9a7765
Plane: support reboot to bootloader
2013-09-04 11:59:16 +10:00
Andrew Tridgell
a93f7c39a9
Plane: updates for new notify API
2013-08-30 13:01:35 +10:00
Randy Mackay
ad8bd16725
Plane: integrate AP_Notify
2013-08-30 13:01:35 +10:00
Andrew Tridgell
accfd46633
Plane: update for new APM_Control API
2013-08-14 14:57:41 +10:00
Andrew Tridgell
74dabad1f3
Plane: added SKIP_GYRO_CAL parameter
...
useful for starting the sim at high altitudes, and for starting planes
without having to hold them still
2013-07-22 12:50:01 +10:00
Andrew Tridgell
c8a83e17d0
Plane: remove old AIR_START code
...
this was never used or tested
2013-07-22 12:50:01 +10:00
Andrew Tridgell
51b9cf3e76
Plane: move failsafe variables into a structure
...
this makes the logic a bit easier to follow
2013-07-22 12:50:00 +10:00
Andrew Tridgell
113bc20f8a
Plane: added a new CRUISE flight mode
...
See
http://diydrones.com/group/apmusergroup/forum/topics/feature-request-hold-heading-mode
this fixes issue #438
2013-07-13 21:45:58 +10:00
Andrew Tridgell
826ad6c086
Plane: unlock roll and pitch when we enter ACRO mode
2013-07-13 12:34:34 +10:00
Andrew Tridgell
f300df5fd1
Plane: added FS_LONG_TIMEOUT and FS_SHORT_TIMEOUT parameters
...
this is to address the issue raised here:
http://diydrones.com/forum/topics/ardupilot-circle-mode
2013-07-12 11:56:04 +10:00
Andrew Tridgell
608007361b
Plane: added initial implementation of ACRO mode
...
rate based control with attitude locking
2013-07-11 09:10:41 +10:00
Andrew Tridgell
d30dd7c3f1
Plane: only run TECS when in an auto-throttle mode
...
this prevents integrator buildup in user controlled modes
2013-07-05 14:55:22 +10:00
Andrew Tridgell
4a0c90246e
Plane: make GPS UART blocking again
2013-06-11 18:50:23 +10:00
Andrew Tridgell
93cd0f9a31
Plane: switch to new AP_Scheduler
...
this gives us more accurate task scheduling in ArduPlane, plus better
monitoring of task timing (via SCHED_DEBUG)
2013-06-04 13:34:58 +10:00
Andrew Tridgell
4c9bc30f58
Plane: make it possible to change control channel ordering without reboot
...
this makes configuration a bit easier
2013-06-03 16:42:38 +10:00
Andrew Tridgell
fb9bf21522
Plane: allow channel mapping of first 4 channels
...
this makes it easier to support DSM and SBUS radios
2013-06-03 16:23:48 +10:00
Andrew Tridgell
515d726ee0
Plane: use RC_Channel::rc_channel() instead of rc_ch[]
2013-06-03 16:23:48 +10:00
Andrew Tridgell
f7697574db
Plane: use the new airspeed driver interface
...
the choice of analog source is now in the airspeed driver
2013-06-03 11:51:09 +10:00
Andrew Tridgell
d9bcfd913a
Plane: reset attitude integrators on mode change
2013-06-01 22:29:38 +10:00
Andrew Tridgell
eba7d6da9a
Plane: removed the old crash_timer code
...
This code is less relevent with the new L1 navigation, and could cause
issues with the pilot not having control after a long dive.
Thanks to Soren for pointing out the issues
See issue #305
2013-05-28 11:19:28 +10:00
Andrew Tridgell
a22f5e3bc4
Plane: enable wind estimation
2013-05-24 11:21:42 +10:00
Andrew Tridgell
fdd509a7c1
Plane: move baro init earlier in startup
...
this ensures it is initialised when CLI takeover by MP happens
Thanks to Prof Avi Levi for reporting this bug
2013-05-06 10:57:57 +10:00
Andrew Tridgell
4e2b88f6e6
Plane: added ATT_CONTROLLER option to select attitude controller
...
set to 1 for the new APM_Control library
2013-05-05 21:51:09 +10:00
Andrew Tridgell
5ba171af9a
Plane: fixed mavlink levelling
...
this was broken by a recent commit (after 2.72 was released)
2013-05-02 13:38:28 +10:00
Andrew Tridgell
a019e3740e
Plane: updates for new compass API
2013-05-02 12:48:14 +10:00
Andrew Tridgell
de3fcbc413
Plane: removed the MANUAL_LEVEL option
...
levelling on every startup is far too error prone. This was just
another parameter that everyone changed.
2013-04-29 14:19:53 +10:00
Andrew Tridgell
2e5834cc7f
Plane: print flight mode as string in logs
2013-04-20 15:18:10 +10:00
Andrew Tridgell
c56f338fe0
Plane: convert to new logging system
2013-04-20 13:52:36 +10:00
Andrew Tridgell
79c6f32400
Plane: made variables static and remove initial rc overrides
...
minor code size savings
2013-04-15 14:46:01 +10:00
Andrew Tridgell
575f346e85
Plane: removed HIL_MODE_ATTITUDE
...
we really need full sensors for HIL with the L1 controller. The flight
is also _much_ better with sensors HIL.
2013-04-12 17:44:40 +10:00
Andrew Tridgell
11eb0cfce1
Plane: update for new AP_Navigation controller class
...
this switches ArduPlane over to use the L1 navigation controller, via
a generic nav_controller object pointer.
Note that the nav_controller controls all types of navigation now,
including level flight and heading hold. This provides a cleaner
abstraction than the old method of special case navigation handling
Pair-Programmed-With: Paul Riseborough <p_riseborough@live.com.au>
2013-04-12 12:48:09 +10:00
Andrew Tridgell
dfb14d760b
Plane: added HIL_SERVOS option
...
this allows for real servo output in HIL
2013-03-30 14:38:43 +11:00
Andrew Tridgell
7db7d7db77
Plane: change FBWB altitude control algorithm
...
this makes FBWB much less sensitive to airframe tuning. When the
elevator stick first goes neutral it locks in the current altitude as
the target altitude. When the elevator stick is off neutral, it moves
the target altitude in proportion to the elevator, at a rate goverened
by the new FBWB_CLIMB_RATE parameter
This prevents the aircraft from slowly drifting in altitude in FBWB,
and gives a more intuitive control mechanism for altitude.
Thanks to Chris Miser from Falcon UAV for help in designing this
change
2013-03-28 10:27:25 +11:00
Randy Mackay
c2055557f5
Plane: add support for GPS fix type 2D
2013-03-27 11:41:51 +09:00
Andrew Tridgell
87c6545ac6
Plane: don't trigger GCS failsafe if GCS never connected
...
The we have never received a heartbeat message from the GCS then don't
use the lack of heartbeat to trigger a failsafe event
2013-03-09 13:48:39 +11:00
Andrew Tridgell
0a0b51cc63
Plane: reset AHRS trim after a level operation
2013-02-20 11:56:02 +11:00
Andrew Tridgell
9f70c6c70d
Plane: make CIRCLE mode hold altitude
...
this will prevent us losing a lot of altitude during the initial
failsafe phase
2013-02-11 13:52:25 +11:00
Andrew Tridgell
28352b3548
Plane: ensure ahrs.init() is called
2013-01-13 17:32:48 +11:00
Andrew Tridgell
86f667f6cc
Plane: added new SERIAL0_BAUD parameter
...
this is useful on PX4
2013-01-13 07:39:40 +11:00
Andrew Tridgell
9e0096ddb5
Plane: fix handling of sensors HIL startup
2013-01-04 12:34:35 +11:00
Andrew Tridgell
b6295c12e1
Plane: fixes for new AP_Relay interface
2013-01-02 10:18:45 +11:00
Andrew Tridgell
edad43611d
Plane: reset last heartbeat time on startup completion
...
this gives more time for the GCS to send its first heartbeat
2012-12-26 08:46:36 +11:00
Andrew Tridgell
cf8e648558
CLI: fixed accel setup
...
disable mavlink callback in CLI
2012-12-24 08:51:33 +11:00
Andrew Tridgell
d54c6989ab
Plane: fixed the last build warnings
...
we now build with no warnings for APM1, APM2 and SITL. Yay!
2012-12-20 22:46:48 +11:00
Andrew Tridgell
feca411943
Plane: added new TRAINING mode
...
this mode gives manual control when the roll or pitch is within the
set limits (the same limits as FBW mode), and prevents the pilot from
flying beyond those limits, essentially a "attitude limited manual"
mode
2012-12-20 22:41:58 +11:00
Andrew Tridgell
18db7b2efd
GPS: move _port setting to init()
...
this is needed to avoid constructor ordering dependencies
2012-12-20 14:52:32 +11:00
Pat Hickey
c441f02426
ArduPlane: init DataFlash obj
2012-12-20 14:51:37 +11:00
Pat Hickey
a14621534c
ArduPlane: port from hal.dataflash to old DataFlash api
2012-12-20 14:51:36 +11:00
Pat Hickey
92b0c302f2
ArduPlane: Ported to AP_HAL
2012-12-20 14:51:36 +11:00
Andrew Tridgell
1104287aa2
Plane: use enum FlightMode in more places
2012-12-01 08:15:48 +11:00
Andrew Tridgell
a6d8dbeac2
Plane: update ArduPlane for new ins interface
2012-11-30 07:15:18 +11:00
Andrew Tridgell
a87394fff2
Plane: don't do accel calibration in HIL mode
...
this should fix the hang on startup
2012-11-25 21:53:37 +11:00
Andrew Tridgell
56e4cbfb1d
Plane: allow reboot on APM1, and add reboot to main CLI menu
2012-11-24 18:20:37 +11:00
Andrew Tridgell
84300c85d6
APM: make it possible to run the CLI on any serial port
2012-11-21 21:41:34 +11:00
Michael Oborne
a5e3ce4655
remove cli planner mode - no longer used
2012-11-21 07:45:45 +08:00
rmackay9
ef727bbb3c
ArduPlane: move to use new INS library instead of IMU library
2012-11-07 19:21:03 +09:00
rmackay9
8c6fd340d7
AP_AHRS: added scheduler parameter to init
...
Required by the AP_AHRS_MPU6000 class which needs to disable timed processes that could interfere with it's communication with the mpu6000
2012-09-29 13:51:21 +09:00
Andrew Tridgell
37cb56f3e1
APM: save another few bytes
2012-09-18 13:58:50 +10:00
Andrew Tridgell
12dc2e79cf
APM: save 100 bytes of memory
...
remove flight_mode_strings array
2012-09-18 13:58:49 +10:00
Andrew Tridgell
4d4a95501f
APM: updates for new GPS detection
2012-09-17 14:45:47 +10:00
Michael Oborne
94f956a0ca
fix AP attitude hil - with randys help
2012-09-15 16:47:18 +08:00
Andrew Tridgell
7e672628ea
APM: removed the GPS_enabled flag
...
this fixes using GPS_PROTOCOL to specify a specific GPS with a GPS
that takes a few updates before it works (eg. needing baud rate
changes).
This makes it easier to use an APM1-1280 with more features enabled
2012-09-11 13:37:34 +10:00
Andrew Tridgell
0812fc4890
APM: reboot only works on the APM2
2012-09-10 11:50:48 +10:00
Andrew Tridgell
cb88681914
APM: added support for MAV_CMD_PREFLIGHT_REBOOT_SHUTDOWN
...
this allows for remote reboot of APM
2012-09-10 11:42:30 +10:00
Andrew Tridgell
a446a7a9ed
APM: allow serial buffer size to be configured
...
very useful for packet forwarding setups
2012-09-08 10:06:35 +10:00
Andrew Tridgell
dcbd0fbd44
APM: cleanup throttle suppression code and don't use airspeed to unsupress
...
this removes the throttle suppression when any of the conditions are
met once, as otherwise flying slow below 10m could zero the throttle.
It also removes the use of airspeed for disabling throttle
supression. Otherwise a strong gust of wind can cause ArduPlane to
try to takeoff!
2012-08-28 20:18:23 +10:00
Andrew Tridgell
d445482ace
APM: added optional use of new APM_Control library
...
thanks to Jon Challinger for the new controllers!
2012-08-22 12:45:14 +10:00
uncrustify
a8e5900624
uncrustify ArduPlane/system.pde
2012-08-21 19:19:51 -07:00
Andrew Tridgell
6d11940ada
AHRS: removed Quaternion build support from APM/ACM/rover
2012-08-22 10:42:21 +10:00
Andrew Tridgell
c960db7af5
APM: allow for separate calibration of airspeed/barometer
...
this is useful just before takeoff, to account for temperature changes
2012-08-15 19:49:09 +10:00
Andrew Tridgell
9fea3e3ac1
APM: pass airspeed sensor to AHRS
2012-08-11 08:57:44 +10:00
Andrew Tridgell
dc47074dbd
MAVLink: removed the need for Mavlink_compat.h
...
we have now fully transitioned to MAVLink 1.0, so we no longer need
the compatibility layer and the old names in the code
2012-08-09 12:22:46 +10:00
Andrew Tridgell
a823c9ceae
APM: removed cli slider and dipswitch options
...
use mavlink/eeprom for all config
2012-08-08 12:12:29 +10:00
rmackay9
06e35820e5
ArduPlane: allow MPU6000's DMP to be used for attitude estimation.
...
Enable by adding this line to APM_Config.h:
#define DMP_ENABLED ENABLED
2012-07-28 19:50:40 +09:00
Andrew Tridgell
de3c9ce56d
Airspeed: change APM to use new AP_Airspeed library
...
the next step is AHRS dead reckoning
2012-07-16 11:21:50 +10:00
Andrew Tridgell
58fd91165f
APM: fixed some build warnings and type errors
2012-07-06 19:59:18 +10:00
Andrew Tridgell
82ede937e7
AnalogSource: convert analogRead() calls to the new API
...
this should give us much better analog values, plus save a bunch of
CPU time
2012-07-01 15:01:05 +10:00
Andrew Tridgell
3a2594fa1a
APM: ArduPlane updates for new compass interface
2012-06-27 16:01:50 +10:00
Andrew Tridgell
2934b4173b
APM: set_centripetal() is now set_fly_forward()
...
this controls more than just centripetal correction
2012-06-27 16:01:49 +10:00
Andrew Tridgell
940d994efb
GPS: Use appropiate GPS_ENGINE settings in APM, ACM and rover
2012-06-10 16:36:18 +10:00
Andrew Tridgell
a684bddbda
GPS: open the GPS serial port with a 256 byte buffer
...
the UBLOX needs more than 128 bytes for reliable parsing
2012-06-08 16:42:03 +10:00
Andrew Tridgell
87ed39ea46
APM: use set_blocking_writes(false) when we have done ground start
2012-03-30 17:46:20 +11:00
Andrew Tridgell
b4107d35e8
MAVLink: raise the serial transmit buffer size to 256 bytes
...
the 128 byte serial transmit buffer was causing significant problems
with queueing of mavlink messages. With 256 bytes we can fit a lot
more messages out in each pass of the code, which makes telemetry more
efficient
As we discussed on the dev call, we now have enough free ram for this
to be worthwhile
2012-03-30 17:46:20 +11:00
Andrew Tridgell
4c4c38f69a
APM: Added MANUAL_LEVEL option
...
when MANUAL_LEVEL is set to 1, we don't do accelerometer levelling at
startup, and instead used the values saved in the EEPROM. This makes
it easier to do levelling on the bench, or once for a series of
flights for the day
2012-03-29 12:39:53 +11:00
Andrew Tridgell
8afd196907
APM: adapt ArduPlane for AHRS framework
2012-03-19 17:29:02 +11:00
Andrew Tridgell
7a9b3d3388
Quaternion: show "Quaternion test" on startup if enabled
2012-03-10 10:34:29 +11:00
Andrew Tridgell
367947fd33
HWSTATUS: if we don't know the voltage, report it as zero
...
this will tell us if board_voltage() is really working
2012-03-10 10:34:28 +11:00
Andrew Tridgell
b20084af7d
APM: added board_voltage() function
2012-03-02 15:48:27 +11:00
Andrew Tridgell
0248b48d30
allow MAG_ENABLE to be changed in flight
...
this disables the compass in DCM if MAG_ENABLE is changed in
flight. Without this we would use a fixed yaw once the compass is
disabled
This also makes sure we don't pass the compass to DCM till we have
done a read. This ensures we have a good compass fix for the initial
DCM heading
2012-02-25 14:51:09 +11:00
Andrew Tridgell
95ef9206dc
DCM: renorm_sqrt_count is now called renorm_range_count
2012-02-23 08:16:08 +11:00
Andrew Tridgell
bc0ed62aa9
adapt mainline APM code to AP_Param
2012-02-13 16:22:51 +11:00