dark0707
/
px4-firmware
forked from Archive/PX4-Autopilot
1
0
Fork 0
Code Pull Requests Activity
35,481 Commits 514 Branches 136 Tags 234 MiB
Commit Graph

107 Commits

Author SHA1 Message Date
Daniel Agar e788fe45b6
systemcmds/manual_control: command line stick input for testing 2021-06-02 09:30:22 -04:00
Daniel Agar 5f775b508f boards: enable CONFIG_OTG_ID_GPIO_DISABLE on all F7/H7 2021-06-01 15:19:15 -04:00
David Sidrane 32e92ba817 Revert:Pull downs - bad levels cause motor spins 2021-06-01 15:18:47 -04:00
Daniel Agar c3884b5bc1
fake_imu (formally fake_gyro) updates for testing gyro filtering 
- fake_imu now publishes sine sweeps over 10 seconds
 - accel is also published so that fake IMU can be selected when the only option
 2021-05-17 20:26:25 -04:00
David Sidrane 50d3af1ba1 mro_ctrl-zero-f7: Initalize PWM as input with Pull Downs 2021-05-05 20:48:06 +02:00
Daniel Agar 58b40fbbb9 boards: move testing to dedicated test variants 2021-04-14 09:21:31 +02:00
Daniel Agar 6874e9fba0 boards: NuttX disable all NSH memory debug commands (mb, mh, mw) by default 
- closes https://github.com/PX4/PX4-Autopilot/issues/17062
 2021-03-30 09:23:43 -04:00
Daniel Agar 631d1647d3 boards: minimize unnecessary differences in default variants 2021-03-28 14:46:47 -04:00
Ryan Johnston bffa83bd47 Reverting LAZYFPU for v1.12 beta1 Compatibility 
Without reverting this a constant boot loop occurs.

Prior to merging, why this occurs on some F7 boards and not this one should be looked at.

With LazyFPU enabled, v1.12.0 beta1 will not boot but without it removed it works fine.
 2021-03-17 06:10:02 +01:00
Daniel Agar 2257c3767e simple gyro auto calibration module 2021-03-15 09:46:47 +01:00
Daniel Agar 4d288512b5 add board architecture specific init defaults 2021-03-09 19:59:41 +01:00
Ryan Johnston 9d0a8928bd Update chip type 
Update chip type from NI to II.
 2021-03-05 21:28:36 +01:00
Daniel Agar 19de1e57e3 gyro_fft promote to modules and include on all boards 2021-03-05 10:56:54 -05:00
Ryan Johnston bc8d9af23e Add Lazy FPU 
Reported that LAZYFPU  interact with the MTD (FRAM) driver.

https://github.com/PX4/PX4-Autopilot/issues/16548
 2021-03-03 14:43:40 -05:00
Beat Küng 7e33d03470 drivers: remove tap_esc 
- it's not used anymore
- it would need a refactoring to use mixer_module
 2021-02-25 09:28:37 -05:00
Daniel Agar 414f9f81d9
move fake GPS to standalone module 2021-02-20 14:13:36 -05:00
Daniel Agar ab0d0fd0be
uORB move to PX4 platform layer 2021-02-17 11:25:56 -05:00
Daniel Agar fb2a199621 delete unmaintaned mkblctrl driver 2021-02-14 10:38:15 +01:00
Daniel Agar a257120e8d boards: use new param default mechanism 2021-02-12 08:27:47 -05:00
Daniel Agar 8f0918a16b boards: remove unused linker __param section 2021-02-08 23:22:48 -05:00
Daniel Agar a2442ffb48 board: enable UAVCAN sensors by default on F7/H7 2021-02-02 09:01:12 +01:00
Ryan Johnston d22eef9396
boards: mRo Control Zero F7 fix for voltage/current sensing 
* Rename GPIO_nVDD_BRICK1v to GPIO_VDD_BRICK1
 2021-01-19 15:48:17 -05:00
Ryan Johnston cea8ad4236 Control Zero F7 - RSSI Fix - SBUS Only/PPM Partial 
This fixes RSSI for the Control Zero F7 but I have noticed that while this works perfectly for SBUS receivers, for PPM receivers it does not decrease the RSSI visual value in QGC when removing the RC transmitter connection.

When a PPM receiver is connected and the connection is lost the autopilot goes into RC Scan Mode (in the RC Update Module) to determine what is connected (even though something already is connected).

The main issue with this is that PPM receivers don't go into RC Failsafe but I don't think it is an issue with this autopilot. It looks to be an issue with the RC Update Module and how it is handled at the module level for non I/O coprocessor autopilots. 


Tested with an X8R (SBUS) and a Dragonlink (PPM) as well as a Dragonlink set to SBUS as the output. SBUS worked as intended. See screenshots below.
 2021-01-19 20:42:28 +01:00
Daniel Agar 1ec10bfcc6
boards: disable CONFIG_ARMV7M_LAZYFPU again (#16573) 
- this was causing hard faults on the CUAV Nora and possibly other boards, disabling everywhere until we fully understand the root cause
 2021-01-17 22:40:21 -05:00
Daniel Agar 7f5fae91b0 boards: mro ctrl zero f7 fix default power module calibration 2021-01-12 16:51:05 -05:00
Daniel Agar cb74cb8692 boards: enable CONFIG_ARMV7M_LAZYFPU everywhere 2021-01-12 09:04:38 +01:00
Daniel Agar 763c3b8fda boards: start enabling multi-EKF by default on F7/H7 2021-01-10 17:56:34 +01:00
Matthias Grob 7545249215 Add flight_mode_manager to all targets with mc_pos_control 2020-12-30 10:25:08 -05:00
David Sidrane 22bc176885 Added mft for queries 2020-12-02 20:40:23 -05:00
David Sidrane 5703070974 mro_ctrl-zero-f7: Use px4_platform_configure 2020-12-02 20:40:23 -05:00
Daniel Agar c60743b306 boards: NuttX increase file name max 32 -> 40 2020-11-08 12:51:59 -05:00
Daniel Agar 233949a377 NuttX upgrade to 10.0.0+ defconfig changes 2020-10-28 14:25:25 -04:00
Daniel Agar 1bf0218c87 boards: mRo Control Zero F7 fix RC input and cleanup sensors init 2020-10-04 22:23:47 -04:00
Tanja Baumann b5ebdb8e41
add system command to get and set system time 
* add system_time command for all boards
 2020-09-26 13:09:01 -04:00
David Sidrane 1e55ce0839 mro_ctrl-zero-f7: Updates for NuttX 9.1.0+ External schedule_note 2020-09-16 21:32:04 -04:00
David Sidrane 2550d6f7c1 mro_ctrl-zero-f7 Updates for NuttX 9.1.0- 
mro_ctrl-zero-f7: defconfig MMCSD enable multiblock
 2020-09-16 21:32:04 -04:00
David Sidrane e8e463b875 cubepilot_cubeyellow Updates for NuttX 9.1.0- 
cubepilot_cubeyellow: defconfig MMCSD enable multiblock
 2020-09-16 21:32:04 -04:00
SalimTerryLi c037dbef21
Rename and move src/drivers/adc to src/drivers/adc/board_adc 2020-09-07 23:09:20 -04:00
Daniel Agar 2c3441aa90 boards: reduce CONFIG_NFILE_DESCRIPTORS 15 -> 12 
- reduced now that calibration uses uORB::Subscription
 - can likely be reduced further (perhaps < 8) with additional testing
 2020-08-21 10:12:13 -04:00
Daniel Agar e3d31a881e boards: NuttX disable posix message queues 2020-07-17 17:00:21 -04:00
Daniel Agar 13e34b32e6 new Bosch BMI088 IMU driver using FIFOs and DRDY 2020-06-11 12:25:13 -04:00
Daniel Agar 6f6efd60b7 boards: centralize optional external I2C sensor start 
- configured with new parameter SENS_EXT_I2C_PRB
 2020-06-10 09:04:13 -04:00
Daniel Agar 5e7d2e830d boards: delete old board.h boilerplate 2020-06-08 19:10:33 -04:00
Daniel Agar d1c12ac7cf boards: mRo Control Zero fix IMU rotations 2020-06-04 11:34:31 -04:00
Daniel Agar 951969ba00
drivers/imu/invensense: new ICM20948 driver on SPI with AK09916 mag 2020-05-22 00:09:30 -04:00
Daniel Agar 746a8f5cf9 commander: reboot/shutdown usability fixes 
- always check with state machine before reboot/shutdown
 - respect BOARD_HAS_POWER_CONTROL (shutdown from command, low battery, power button)
 - px4_shutdown_request add optional delay and always execute from HPWORK
 - px4_shutdown_request split out px4_reboot_request
 2020-05-06 13:53:54 -04:00
Daniel Agar 28d2aca699 boards: include all procfs entries on boards that aren't flash constrained 2020-05-01 20:59:57 -04:00
Daniel Agar 8d0c92003a boards: remove all CONFIG_NXFONTS_DISABLE* 2020-05-01 20:59:57 -04:00
Daniel Agar 06478d9997 delete obsolete SENSORIOCSPOLLRATE/SENSORIOCRESET and systemcmds/config 2020-04-15 23:33:41 -04:00
mcsauder 6548fde024 Whitespace cleanup to quiet new blank line at EOF git hook. 2020-04-15 23:00:39 -04:00