* Navigator: DO_CHANGE_SPEED: only store sinlge cruising_speed_current_mode
This stored cruising speed setpoint is reset on mode change and
after a VTOL transition.
* Navigator Mission: replay DO_CHANGE_SPEED items when resuming mission
* Navigator: remove cruising_speed_sp_update()
Speed changes in a mission are handled directly in the position controllers,
and no longer in Navigator.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Increased size for ORB_ID from uint8_t to uint16_t
Created a type: orb_id_size_t = uint16_t.
There are still a couple of places where the size
of the ORB_ID is assumed to be less than 16-bits.
The places that I have found are commented regarding
this and can be found with a search on orb_id_size_t.
- split mag_3d into new standalone mag fusion and mag fusion allowed to update all states (full mag_3d)
- new dedicated control logic for mag/mag_3d fusion and standalone mag heading fusion
- if WMM available use for mag_I and mag_B init
- mag states reset if external yaw reset (yaw estimator, GPS yaw, etc)
- mag reset if declination changed (eliminate _mag_yaw_reset_req)
- mag fusion (but not mag_hdg or mag_3d) can be active during gps_yaw or ev_yaw (if yaw aligned north)
Co-authored-by: bresch <brescianimathieu@gmail.com>
- simplify vehicle_status.arming_state down to just armed and disarmed
- ARMING_STATE_INIT doesn't matter
- ARMING_STATE_STANDBY is effectively pre_flight_checks_pass
- ARMING_STATE_STANDBY_ERROR not needed
- ARMING_STATE_SHUTDOWN effectively not used (all the poweroff/shutdown calls loop forever in place)
- ARMING_STATE_IN_AIR_RESTORE doesn't exist anymore
- collapse ArmStateMachine into commander
- all requests already go through Commander::arm() and Commander::dismarm()
- other minor changes
- VEHICLE_CMD_DO_FLIGHTTERMINATION undocumented (unused?) test command (param1 > 1.5f) removed
- switching to NAVIGATION_STATE_TERMINATION triggers parachute command centrally (only if armed)
---------
Co-authored-by: Matthias Grob <maetugr@gmail.com>
* ekf2-test: remove outdated codegen comparison
The definition of states changed so the comparison with the old
derivation cannot work anymore.
---------
Co-authored-by: bresch <brescianimathieu@gmail.com>
Some system are able to dead-reckon for a while after losing GPS or
other sources providing positional feedback. If the estimated position
error grows above the failsafe threshold, the system enters a failsafe
mode. As the position error estimate is growing linerly over time, and
it is recommended to take action before entering the failsafe, we here
warn the user about the imminent failsafe and propose to take manual
control.
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* [not-working] add a gz-omnicopter model
* Fix axis directions on omnicopter model
The omnicopter joint axis directions had to be adapted for sdf 1.9 as it has different conventions for joint axis definitions.
* include model from gz-fuel & remove mesh files
* Fix omnicopter model using fuel
---------
Co-authored-by: Jaeyoung Lim <jalim@ethz.ch>
If at the last powercycle one mission was uploaded, the counter in dataman was 1. On the next powercycle the mavlink mission counter was reset to zero and on first mission upload updated to 1 again. Other modules check, if the mission was changed based on the counter, like the mission.cpp loaded the mission counter from the dataman. On a new mission, the comparison of the counters failed, because both were the same value even if the mission was completely different.
This can be useful if using a full EV + GNSS setup and you start indoors, then fly outside. Once GPS is good and the only missing requirement is yaw alignment the yaw estimator reset is performed and EV yaw will automatically stop itself.
There is no reason to contrsain the position uncertainty, estpecially
when flying with velocitiy aiding only.
Note that all the variances are already contrained to sane values at the
end of the covariance prediction
- set vision attitude error filter uninitialized if vision data stops
- ev error filter is only compiled when ev config is selected
Co-authored-by: bresch <brescianimathieu@gmail.com>
bresch
Silvan Fuhrer
Beat Küng
hskrieg
Christian Rauch
Dusan Zivkovic
Daniel Agar
alexklimaj
Roman Dvorak
PX4 BuildBot
Julian Oes
Ayham Alharbat
Konrad
Beniamino Pozzan
bazooka Joe
Junwoo Hwang