The entire logic did not work for the case when the throttle channel is
reversed because then QGC sets trim = max for that channel and
the result is only half the throttle range.
This adds support for the TI LP5562 RGB LED driver.
Things to note:
- The driver is initialized in simple PWM mode using its internal clock,
for R,G,B, but not for W(hite).
- The chip doesn't have a WHO_AM_I or DEVICE_ID register to check.
Instead we read the W_CURRENT register that we're generally not using
and therefore doesn't get changed.
- The current is left at the default 17.5 mA but could be changed using
the command line argument.
Datasheet:
https://www.ti.com/lit/ds/symlink/lp5562.pdf
Signed-off-by: Julian Oes <julian@oes.ch>
* Removed obsolete voxl2-io directory
* Updated support for ModalAI FC v2 board
* Added UAVCAN back in and removed local position estimator and attitude estimator Q that are no longer supported.
* Removed unneeded IMU drivers
set_vtol_transition_item sets the params of the mission item directly
to values that make sense for NAV_CMD_DO_VTOL_TRANSITION, but don't
for other NAV_CMDs. So make sure that whenever we use it, we then in
the next step reset the touched mission_item fields.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Our serial_test showed only ~84kB/s with the default 256 RX buffer size
with significant ~2.5ms periods of the flow control RTS pin being
asserted. Increasing size to 600 (same as FMU-v5x) brings the throughput
only to ~190kB/s, while a size of >1500 achieves ~350kB/s. Larger RX
buffers do not increase throughput anymore, while the theoretical
maximum is 375kB/s.
Transmit buffer size is increased to 10kB same as on FMUv5x to prevent
any future differences in queue behavior and throughput. serial_test
showed ~350kB/s throughput at 3kB TX buffer size, so this is just a
precaution.
* refactored uncommanded descend quadchute
- use fixed altitude error threshold
- compute error relative to higest altitude the vehicle has achieved
since it has flown below the altitude reference (setpoint)
* disabled altitude loss quadchute by default
* altitude loss quadchute: added protection against invalid local z
---------
Signed-off-by: RomanBapst <bapstroman@gmail.com>
- ArmingStatus DroneCAN message STATUS field is only set to true based on
arming_status.armed
- Cannode prearm state is set to true always when ArmingStatus DroneCan
message is received
- Instead we disable interrups on Nuttx where needed
- No lock is held during param export. Params can be changed
concurrently and we rely on the fact that another export will be
triggered in that case.
5s is a more reasobale time for tailsitters, which rely differently on this param
than other VTOL types. Tailsitters will ramp the pitch up withing this time,
while for other VTOLS types its only the max transitiont time.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
This is now using the advanced lift drag plugin.
The important step was to enable airmode for yaw, otherwise yaw gets
saturated at low throttle and we can barely roll.
The other trick was to raise airspeed a little bit to avoid operating
too much at the lower end of throttle where control authority is low.
Signed-off-by: Julian Oes <julian@oes.ch>
* RateControl: rename setGains to setPidGains to be more precise
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
* FW Rate controller: only allow to disable Yaw in Acro, not roll and pitch
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
---------
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
mcsauder
oneWayOut
Matthias Grob
Julian Oes
Eric Katzfey
bresch
Ramon Roche
Giacomo Bertelli
Silvan Fuhrer
Niklas Hauser
Roman Bapst
henrykotze
Beat Küng
Thomas Debrunner
alexklimaj
JaeyoungLim
Daniel Agar
Junwoo Hwang