nxp/rt117x:Fix Pin IRQ
nxp/rt117x:Support 4 i2c busses
nxp/rt117x:Add px4io_serial support
nxp/imxrt:Expand ToneAlarmInterface to GPT 3 & 4
px4_fmu-6xrt:Using imxrt_flexspi_nor_octal
px4_fmu-6xrt:Entry is start
px4_fmu-6xrt:Add Proper MTD
px4_fmu-6xrt:Set I2C Buses
px4_fmu-6xrt:Proper SPI usage
px4_fmu-6xrt:Adjust memory Map to use the 2 MB
px4_fmu-6xrt:Bring in ROMAPI
px4_fmu-6xrt:Push FLASH to 200Mhz
px4_fmu-6xrt:Use BOARD_I2C_LATEINIT
px4_fmu-6xrt:Clock Config remove unused devices
px4_fmu-6xrt:Remove EVK SDRAM IO
px4_fmu-6xrt:Enable SE550 using HW_VER_REV_DRIVE
px4_fmu-6xrt:Use MTD to mount FRAM on Flex SPI
px4_fmu-6xrt:Manifest
px4_fmu-6xrt:Restore board_peripheral_reset
px4_fmu-6xrt:Set I2C buss Interna/Externa and startup
nxp/rt117x:Set 6 I2C busses
px4_fmu-6xrt:Correct Clock Sources and Freqency Settings
px4_fmu-6xrt:Correct ADC Settings
px4_fmu-6xrt:Tune FlexSPI config and sync header with debug variant Linker prep for rodata ahb partitioning
px4_fmu-6xrt:FlexSPI prefetch partition split .text and .rodata
Current config
1KB Prefetch .rodata
3KB Prefetch .text
px4_fmu-6xrt:Run imxrt_flash_setup_prefetch_partition from ram with barriers
px4_fmu-6xrt:Use All OCTL setting from FLASH g_flash_config SANS lookupTable
px4_fmu-6xrt:Octal spi boot/debug problem bypass
px4_fmu-6xrt:Add PWM test
px4_fmu-6xrt:Fix clockconfig and USB vbus sense
px4_fmu-6xrt: Use TCM
px4_fmu-6xrt: Ethernet bringup
imxrt: use unique_id register for board_identity
px4_fmu-6xrt: update ITCM mapping, todo proper trap on pc hitting 0x0
px4_fmu-6xrt:correct rotation icm42688p onboard imu
rt117x: Add SSARC HP RAM driver for memory dumps
px4_fmu-6xrt: Enable hardfault_log
px4_fmu-6xrt: Enable DMA pool
px4_fmu-6xrt: fix uart mapping
px4_fmu-6xrt: enable SocketCAN & DroneCAN
px4_fmu-6xrt:Command line history TAB completion
px4_fmu-6xrt:Fix pinning duplication
px4_fmu-6xrt:Support conditional PHY address based on selected PHY
px4_fmu-6xrt:Add Pull Downs on CTS, use GPIO for RTS
px4_fmu-6xrt:Set TelemN TX Slew rate and Drive Strenth to max
px4_fmu-6xrt::Set TELEM Buffers add HW HS
px4_fmu-6xrt:Turn off DMA poll
px4_fmu-6xrt:RC_SERIAL_PORT needed to be px4io to disable rc_input using TELEM2!
px4_fmu-6xrt: bootloader (#22228)
* imxrt:Add bootloader support
* bootloader:imxrt clear BOOT_RTC_SIGNATURE
* px4_fmu-6xrt:Add bootloader
* px4_fmu-6xrt:bootloader removed ADC
* px4_fmu-6xrt:bootloader base bootloader script off of script.ld
* px4_fmu-6xrt:add _bootdelay_signature & change entry from 0x30000000 to 0x30040000
* px4_fmu-6xrt:hw_config Bootloader has to have 12 bytes
px4_fmu-6xrt:Default to use LAN8742A PHY
px4_fmu-v6xrt:VID Set to Drone Code
board_reset:Enable ability to write RTC GP regs
px4_fmu-6xrt:Fix CMP0079 error
rt117x:micro_hal Add a PX4_MAKE_GPIO_PULLED_INPUT
px4_fmu-v6xrt:Set CTS High before VDD_5V applided to ports to avoid radios fro entering bootloaders
fmu-v6xrt: increase 5v down time
fmu-v6xrt:Ready for Release DEBUGASSERTS off and Console 57600,
Bootloder updated.
imxrt:board_hw_rev_ver Rework for 3.893V Ref
px4_fmu-v6xrt:Move ADC to Port3
also for the other linux target builds. It's a follow up to
e5503480e3
I wasn't aware that there are multiple different
container versions used for almost the same build.
- update all msgs to be directly compatible with ROS2
- microdds_client improvements
- timesync
- reduced code size
- add to most default builds if we can afford it
- lots of other little changes
- purge fastrtps (I tried to save this multiple times, but kept hitting roadblocks)
SD is on SPI3 - correct pin mapping
Fix DMA Mapping for all SPI and RX DMA on U[S]ART RX
Fix Memory MAP SRAM size
Removed unused GPIO
Used proper I2C definitions
Ensure Watchdog is configured for debugging
Fixed FLASH param definitions
Removed unedded SPI init
matek_gnss-m9n-f4:Correct Board ID and Size
Build order SJF
Added Support for F40x
- include icm20948 on most boards by default
- create more test variants for default boards near flash limit (cuav_nora_test, cuav_x7pro_test, holybro_durandal-v1_test)