dcb181d2d8
Copter: use new AP_Scheduler library
2013-01-12 12:02:57 +11:00
68b62abd38
ArduCopter with the new Camera and Relay classes for APM1 and APM2.
...
All changes by Sandro Benigno
2013-01-02 09:55:37 +11:00
e850ab7ccd
ArduCopter: add AUTO_VELZ_MIN, AUTO_VELZ_MAX and PILOT_VELZ_MAX to allow better control of climb/descent rate in auto and manual throttle modes
2013-01-02 09:24:31 +11:00
9e986801c9
Copter: fixed SITL for ArduCopter
2012-12-20 14:52:34 +11:00
ada10f6eb2
ArduCopter: change comment references to AP_Var to AP_Param
...
* jsut to clean up the grep for "AP_Var"
2012-12-20 14:51:31 +11:00
2f748f8382
ArduCopter: renamed BATT_FAILSAFE to FS_BATT_ENABLE
2012-12-10 23:47:14 +09:00
d31efebd44
ArduCopter: rename throttle failsafe parameters.
...
Switch to LAND flight mode if throttle failsafe triggers and we do not have a GPS.
THR_FAILSAFE renamed to FS_THR_ENABLE.
THR_FS_VALUE renamed to FS_THR_VALUE.
THR_FS_ACTION removed (action is now controlled by setting FS_THR parameter).
2012-12-10 23:38:43 +09:00
2f1b2b70e6
ArduCopter: added ACRO_TRAINER parameter to allow enabling/disabling the acro training function which will bring the roll back to within +- 45 degrees
2012-12-10 22:27:46 +09:00
dadad8677e
ArduCopter: added descriptions for most parameters that did not have them
...
Renamed loiter_radius to circle_radius to better reflect it's purpose.
Removed some unused parameters including WP_MODE, WP_MUST_INDEX, LOG_LASTFILE, AXIS_P
2012-12-10 21:45:57 +09:00
56ceb230cb
ArduCopter: add YAW_OVR_BEHAVE to allow control of when autopilot takes back control of yaw after pilot overrides it during a mission
2012-12-09 18:04:31 +09:00
39d524212f
ArduCopter: allow accel based throttle controller to be enabled/disabled with the new THR_ACC_ENABLE parameter.
...
When disabled the original velocity based throttle controller is used.
2012-12-06 10:31:57 +09:00
a5bb54e36e
ArduCopter: RTL clean-up and slightly improved landing sensor
...
Consolidated RTL state to be captured by rtl_state variable.
Combined update_RTL_Nav and verify_RTL functions which performed the same function but one was for missions, the other for the RTL flight mode.
Renamed some RTL parameters and global variables to have RTL at the front.
Landing detector now checks accel-throttle's I term and/or a very low throttle value
2012-12-06 10:31:52 +09:00
7b4ed2d227
ArduCopter: restored landing detector to landing throttle mode.
...
Added LAND_SPEED parameter to control the rate of descent for the last 10m of a landing.
Added CH6 tuning for accel based throttle controller.
2012-12-06 10:31:20 +09:00
3cbef57c64
ArduCopter: first merge of leonard's accel based altitude controller plus other changes from Randy
...
Changes include:
New low-level get_throttle_accel function takes target acceleration and compares vs earth-frame Z accelerometer values to produce output to motors.
Higher level throttle controllers modified to call new get_throttle_accel controller
Throttle_rate_stabilized controller added which maintains a desired climb/descent rate
Throttle_land controller added - descends using normal auto throttle controller to 10m then descends at 50cm/s
Multiple throttle modes added including landing mode
Land flight mode no longer needs GPS
Throttle cruise maintenance moved to update_throttle_cruise function
2012-12-06 10:30:49 +09:00
5723021be1
ACM: TradHeli
...
Creating Rate Feed-Forward Parameters
2012-12-04 13:47:38 -05:00
cd07d965a7
Copter: ported RSSI_PIN option from ArduPlane
...
this is useful for OSD users
2012-11-22 20:59:33 +11:00
e92b560df5
ArduCopter: low baterry failsafe
2012-11-15 23:35:41 +09:00
d2a5928c06
Ap state updates
2012-11-09 22:15:15 -08:00
1f801714e8
ArduCopter: incorporate new version of inertial navigation
...
Moved several navigation functions from ArduCopter.pde to navigation.pde
2012-11-07 19:21:31 +09:00
d9b4407e64
AP_InertialSensor: changes after review with Tridge.
...
sanity checking added to accelerometer calibration routine.
user feedback is sent using gcs_send_text_fmt instead of Serial.printf.
moved ins parameters to new eeprom number to avoid conflicts with older parameters.
other small changes including renaming of functions and parameters.
2012-11-07 19:21:15 +09:00
a1b4ec6d0e
ArduCopter: move to use new INS library instead of IMU library
2012-11-07 19:21:09 +09:00
5e8043fd9c
ArduCopter: changed ACRO_ROLL_STABILIZE and ACRO_PITCH_STABILIZE to parameters
...
Changes on behalf of Leonard Hall
2012-10-23 21:30:50 +09:00
4395fad6e9
ArduCopter: incremented eeprom format version to force users to accept the new defaults.
...
Particularly important is the roll-pitch I term move from the stabilize to rate controllers.
2012-10-19 16:14:51 +09:00
4a41a3d210
ArduCopter: added BATT_VOLT_PIN and BATT_CURR_PIN parameters to allow support for new 3DR IV battery voltage and current monitor
2012-10-13 18:40:46 +09:00
ea4f256f8e
ArduCopter: BATT_PIN parameter added to allow you to select which pin is used for voltage and current measurements
...
To save a parameter, the current sensor pin is assumed to always be 1 higher than the voltage pin.
2012-10-02 22:16:19 +09:00
a73bc70553
ACM : Params - formatting cleanup
2012-09-10 20:22:11 -07:00
c9d34c1737
ArduCopter: fixes to allow AP_Mount to work on APM1 with original default channels and fix to reenable support for 3-axis gimbals on APM2.
...
Channels 5 to 11 changed to RC_Channel_aux.
Removed channel 9 because APM_RC doesn't support it in any case.
Updated EEPROM format version to 119 because of the change to RC_Channel_aux and because k_param_rc_11 moved to be after k_param_rc_10.
2012-09-02 12:51:23 +09:00
e8d928cca4
ACM: added TELEM_DELAY to ArduCopter
2012-08-30 09:03:01 +10:00
6a893c11c7
uncrustify ArduCopter/Parameters.h
2012-08-21 18:57:21 -07:00
2a83f1eef2
ArduCopter: remove RTL_LAND parameter as it's been deprecated in favour of APPROACH_ALT.
...
Updated comments on ALT_HOLD_RTL and APPROACH_ALT to make it a little easier to understand.
2012-08-14 12:14:35 +09:00
9cc705939a
Add a second mount instance
2012-08-08 23:07:25 +02:00
c2a4d59132
AP_Param: update ArduCopter core for new AP_Param interface
2012-08-08 12:11:57 +10:00
d9f1140278
ArduCopter: Use generic channel names for AP_Mount servos.
...
This simplifies mission planner, the same code can be used for plane and copter now.
2012-08-06 23:33:51 +02:00
e93daca17e
Fix heli compilation
2012-08-06 23:30:02 +02:00
b8c7b8a786
RC_Channel: Allow each channel to know who they are, this simplifies the enabling and output function calls.
2012-08-05 23:08:31 +02:00
ad45012739
Arducopter: Renamed Config define (RTL_HOLD_ALT)
2012-07-19 17:50:15 -07:00
5a73a2b9cd
Arducopters parameter: Adjusted RTL_ALTITUDE units so they reflect comments in config.h
2012-07-19 09:50:57 -07:00
c9d3ab5413
Oilpan ADC parameters added
...
including a function that configures each Accel Axis
Defaults matching old behavior
Added param group
2012-07-18 22:57:11 -07:00
29b6ec0b11
ArduCopter: reverted channel 5~8 to be regular RC_Channel objects, restored rc_camera_roll and rc_camera_pitch RC_Channels and created new rc_camera_yaw RC_Channel to control the camera mount servos.
...
Defined camera_mount (MNT_) in Parameters.h and Parameters.pde so that it appears in global parameters list.
Removed unused camera_*_gain and camaera_*_continuous parameters.
2012-07-15 16:36:05 +09:00
c73f7ef3ab
AP_Limits library, provides modular "limits" such as altitude and geo-fencing.
2012-07-14 19:26:17 -07:00
d4a0cb5db1
Added Michael Pursifull's Maxsonar HRLV model support
2012-07-11 18:46:47 -07:00
0620d86bfd
Arducopter:Params
...
WP_RADIUS_DEFAULT is now stored the same as Arduplane
2012-07-10 21:53:37 -07:00
af5423b863
Toy Mode: High Yaw default
2012-07-10 21:53:37 -07:00
dfe0983e1e
Merge the changes from APM_Camera branch into ArduCopter
...
Conflicts:
ArduCopter/Camera.pde
ArduCopter/Parameters.pde
2012-07-11 00:39:13 +02:00
038116f521
Airspeed patch:
...
pre-calculated airspeed resistance pitches copter automatically to gain a certain speed allowing the speed controller to work off of a better set point - similar to Alt hold.
added param tilt_comp with a default of 54 which equals 19.5° of pitch to go 6m/s
upped Z and Y target speeds to int32_t for speed squared calculation
2012-07-09 13:13:32 -07:00
6e93ab6af6
Parameters: Added flag for camera pitch/roll servos (continuous or regular)
2012-07-04 21:06:21 -05:00
3a3966736c
Params
...
Added Tilt_Compensation to Params,
deprecated RTL_Land_Enabeled
RTL_Approach_alt is not int16_t, -1 means do noting. 0 means land, >1 means hover to that altitude after timeout.
2012-07-03 17:33:03 -07:00
e35fb9ecd7
Parameters
...
removed unused parameters for retro loiter
2012-07-01 13:40:12 -07:00
49401bffae
Params: Added toy_yate_rate
2012-06-29 21:20:27 -07:00
55092c25a6
SITL: enable the SIM_* parameters in ArduCopter and ArduPlane
2012-06-29 15:10:52 +10:00
839b8865aa
Parameters.h: throttle_min and throttle_max now have defaults from Config.h
2012-06-20 15:02:00 -07:00
15aea320cb
Added note to remove this unused param
2012-06-03 11:13:50 -07:00
9d92602188
changed WP radius to AP_Int16
2012-05-28 22:39:29 -07:00
c8fb9a6635
More CopterLEDS changes.
...
Merged CopterLEDS and Piezo functions to eliminate pin conflict on APM2. Created new Parameter bit to turn piezo function on and off from MP. Moved GPS and Aux pin assignments to allow commonality between APM1 and 2. Set LED_Mode parameter default to 9 in order to make CopterLEDS completely backwards compatible with old Motor LEDS and Piezo code. Legacy users should see no difference.
2012-05-15 12:00:21 -04:00
60c347e23b
Parameters: Added g.retro_loiter which is configurable by the user via the MP.
2012-04-23 00:17:52 -05:00
f9affb3295
Merge branch 'master' of https://code.google.com/p/ardupilot-mega into auto-approach
...
Conflicts:
ArduCopter/Parameters.h
2012-04-16 10:23:01 -05:00
a366bb2f81
Parameters: Changed rtl_approach_alt to float to support more granular altitudes
2012-04-16 10:06:29 -05:00
95cb35c7bb
AHRS: enable AHRS_ group in ArduCopter
2012-04-16 20:55:14 +10:00
7ba8c291bd
Parameters: Added new APPROACH_ALT params (g.rtl_approach_alt) which stored the users desired target altitude after RTL is complete.
2012-04-15 16:51:41 -05:00
0a3bc9a66a
ArduCopter - LEDS - two new parameters to support COPTER_LEDS.
...
Code by Robert Lefebvre.
2012-04-12 22:55:28 +09:00
f8210b164c
ArduCopter - Parameters.h - changed initialisation order to remove compiler warning (have not changed enum values so shouldn't require eeprom format id update)
2012-04-09 17:37:06 +09:00
ee308ea06c
ArduCopter - increased firmware version to 118. Removed nearly all heli parameters as these are all created by the AP_MotorHeli class now.
...
Note: we cannot move the heli_servos to the AP_MotorHeli class yet because of a small issue in the parameters class.
2012-04-04 22:55:07 +09:00
a480b32400
Added support for TradHeli H1 swashplate type. Added new param heli_h1_swash_enabled.
...
Signed-off-by: Robert Lefebvre <robert.lefebvre@gmail.com>
2012-03-03 08:14:14 -05:00
e213f6780e
ACM: added RC_SPEED MAVLink parameter
...
this will set the speed for APM_RC.SetFastOutputChannels()
2012-03-02 17:57:08 +11:00
f781bd735b
ACM: fixed Parameters.h to avoid duplicate keys
...
unfortunately everyone needs to reload
2012-03-02 15:48:28 +11:00
b76c4ecb22
added stab_d gain scheduling
2012-02-28 20:16:40 -08:00
04b70ffdc2
added Axis_Lock params
2012-02-18 21:13:06 -08:00
232359186e
TradHeli - fixed small parameter bug affecting helis. The servo parameters were declared as GSCALAR instead of GGROUP in Parameters.pde.
...
also renamed heli parameters from _coll_ to the more descriptive _collective_
2012-02-18 20:57:51 +09:00
718a5b70e3
AP_Param: fixed saving of sensor calibration
...
this fixes the saving of the accel and gyro calibration to EEPROM,
which was initially broken by the AP_Param conversion
2012-02-18 10:51:57 +11:00
3d63bb6cd4
Added acro_p to the params
2012-02-15 11:29:25 -08:00
91edeeeef2
added RTL_land_enabled
...
added auto_pilot slew rate
2012-02-15 09:10:14 -08:00
aa0662008b
Added new params for CH6 Tuning
...
moved enums to give more room for additional PIDs for Loiter
added new Acro_P gain
added auto_land_enabled option
added pi_loiter_lon and pi_loiter_lat for separate tuning of loiter
2012-02-15 09:10:14 -08:00
bf1eb670e3
update main parameter code for AP_Param in ACM
2012-02-13 16:22:52 +11:00
31614c39dd
Cosmetic
2012-01-30 21:13:03 -08:00
974c825f4a
Optflow - minor fix to D term defaulting
2012-01-29 21:06:41 +09:00
7833cea9d4
2.2B6 - Please verify Heli still functions properly.
...
Added AC_PID lib
Updated landing code
bug fixes
2012-01-28 22:00:05 -08:00
2c906b7b27
OpticalFlow - replaced PI controller with PID controller.
...
Modified optical flow hold to use aggregated position instead of speed.
2012-01-25 21:55:14 +09:00
aace39e65c
Converted distance gains to CM
...
added loiter_d for rate control, equal to old Nav_P gain
2012-01-21 22:13:57 -08:00
5180592913
Added Auto_land_timeout to params
2012-01-20 22:52:30 -08:00
19053bb725
Updated Firmware version
2012-01-20 22:52:30 -08:00
1bebb9452b
AC sync battery code with arduplane
2012-01-21 06:29:09 +08:00
ed9f7cb1b6
Update battery monitoring code for ArduCopter
...
Fixes compatibility for APM2. Also a significant update to the battery monitoring code: We previously had monitoring modes for individual cell voltages for 3 and 4 cell lipos. These have been removed as they were never really supported (the cell voltages were computed but were not reported or recorded anywhere). Also, some clean-up/prep work was done for supporting monitoring 2 separate battery packs. The CLI battery and current monitoring tests were consolidated into 1 test.
changed
2012-01-15 17:10:02 -07:00
f68d23d91e
ArduCopter - added ROLL_PITCH_STABLE_OF (i.e. Stabilised Roll/Pitch + adjustments based on optical flow)
...
Removed optical flow from regular loiter for now until it's tested.
2012-01-09 13:53:54 +09:00
26267f75b2
Reverted to Crosstrack like in Arduplane, requires Degrees * 100
2011-12-30 23:48:04 -08:00
f41835d546
Added Stabilize_D parameter
2011-12-29 23:02:02 -08:00
07041c2149
TradHeli - modified the default collective min/max values to restrict movement to about half the full range.
2011-12-26 16:59:01 +09:00
72605f846c
renamed super simple
2011-12-15 20:51:41 -08:00
88b3708dcf
added altitude to circle mission
2011-12-15 20:51:40 -08:00
8b78c4a4c5
Changes to logging file system to avoid problems with 0 and 1 page logs
2011-12-13 20:09:07 -07:00
e4559bbf5c
Added param option for Simple mode reset
2011-12-12 17:47:45 -08:00
67855b207d
Arducopter, RangeFinder - added SONAR_TYPE parameter and properly support the XL (default), LV and long distance XL (aka XLL) sonar types
2011-12-11 16:40:59 +09:00
1621f3a638
allow CH7 to be set via params
2011-11-26 16:39:28 -08:00
556db68d2d
Made loiter rad smaller in storage
2011-11-20 00:22:53 -08:00
d1c161ecd0
Upped version
...
added new logging params
added crosstrack gain
re-ordered param inits
2011-11-19 14:00:23 -08:00
fed5c0b204
Mission Scripting updates
2011-11-16 00:22:23 -08:00
70aadd4afc
TradHeli - added two parameters to improve heli control.
...
heli_phase_angle allows pilot roll/pitch command to be translated into mixed roll and pitch.
heli_coll_yaw_effect mixes some collective into the yaw so tail can counter act collective movements more easily.
2011-11-13 22:20:57 +09:00
04491d66db
Fixed scaling issue with Circle mode
2011-11-13 00:24:25 -08:00
7dd737ad90
Merge branch 'master' of https://code.google.com/p/ardupilot-mega
...
Conflicts:
Tools/autotest/autotest.py
2011-11-12 21:53:08 -08:00
b3747ab10f
fix loiter radius
2011-11-13 08:24:56 +08:00
be3edc19f8
Fixed type error in params
2011-11-12 15:15:33 -08:00
Andrew Tridgell
rmackay9
Pat Hickey
Robert Lefebvre
Jason Short
uncrustify
Amilcar Lucas
Andreas M. Antonopoulos
Adam M Rivera
Michael Oborne
Doug Weibel
Jason Short