c3b7e76c28
Plane: added flaperon support
...
this adds FLAPERON_OUTPUT and FLAP_IN_CHANNEL to allow both manual
and auto flap control for both normal flaps and flaperons
2014-02-06 12:38:59 +11:00
6cabca690e
Plane: fixed RSSI_RANGE enum
...
many thanks to Valince for spotting this
2014-01-31 12:14:18 +11:00
3a986474e0
Plane: added RSSI_RANGE parameter
2014-01-30 11:29:35 +11:00
d3adf4c32c
Plane: enable AP_BoardConfig
2014-01-20 17:06:28 +11:00
874110b29d
Plane: make LOG_BITMASK 32 bits
2014-01-14 13:06:52 +11:00
c87d72353f
Plane: Introducing FENCE_RETALT parameter.
2013-12-31 09:48:20 +11:00
b0a0316dd6
Plane: Now using AP_Arming library.
2013-12-11 17:29:23 +11:00
5a0cb5dea4
Plane: added sonar logging to dataflash
2013-11-28 21:49:27 +11:00
8383abc1fe
Plane: added SERIAL2_BAUD and rename SERIAL3_BAUD to SERIAL1_BAUD
2013-11-26 13:00:03 +11:00
2fa5e6310d
Plane: added 3rd telemetry stream on platforms that have it
...
this generalises the gcs object usage
2013-11-23 19:29:22 +11:00
490a061c6f
Plane: added HIL_ERR_LIMIT
...
this allows DCM to recover if HIL attitude drifts too far from true attitude
2013-11-23 18:50:57 +11:00
5bf1463e7a
Plane: added RALLY_LIMIT_KM
...
this will prevent an embarressing use of a rally point from the wrong
airfield
2013-10-06 14:51:13 +11:00
d275f50539
Plane: added GROUND_STEER_ALT and GROUND_STEER_DPS
...
this uses the new AP_SteerController steering controller developed for
the rover code to allow for ground steering of planes
2013-10-05 07:46:27 +10:00
081510d37a
Plane: added ACRO_LOCKING parameter
...
this enables/disables the attitude locking in acro mode, allowing acro
to be a pure rate controller
2013-10-05 07:45:12 +10:00
497c95de8e
Plane: Add support for rally points.
...
Added parameter RALLY_TOTAL.
Added handlers for new MAVLink messages RALLY_POINT and
RALLY_FETCH_POINT.
defines.h modified to make room in EEPROM to store rally points.
rally.pde added and is responsible for ensuring rally points get
stored in the correct spot in EEPROM.
Multiple Rally/RTL point support now done. If rally points have
been defined, then when RTL mode is entered, the closest Rally
point is chosend and the plane loiters at that point.
Note only 10 rally points can be defined; this is to save space in
the APM's EEPROM.
2013-10-03 12:21:08 +10:00
c64d444b5a
Plane: integrate BattMonitor
2013-10-03 11:16:08 +09:00
dd6a69f588
Plane: added WP_MAX_RADIUS parameter
...
useful when using AUTO_FBW_STEER for manual steering in competitions
2013-09-13 17:43:08 +10:00
cc6acac1dd
Plane: added AUTO_FBW_STEER option
...
this is an unusual option that gives FBWA flight control in AUTO
mode. It is being added to support use of APM in an aerial robotics
competition where students need to pilot the plane, but they still
need waypoint triggering of payloads
2013-09-13 14:38:09 +10:00
accfd46633
Plane: update for new APM_Control API
2013-08-14 14:57:41 +10:00
233b033e8c
Plane: removed old speed/altitude control algorithms
...
Use TECS only. This makes the code a lot simpler and easier to
properly document
2013-07-22 13:28:11 +10:00
74dabad1f3
Plane: added SKIP_GYRO_CAL parameter
...
useful for starting the sim at high altitudes, and for starting planes
without having to hold them still
2013-07-22 12:50:01 +10:00
608345415b
Plane: pass aircraft parameters to attitude controllers
...
also cope with rename of airspeed min/max variables
Pair-Programmed-With: Paul Riseborough <p_riseborough@live.com.au>
2013-07-18 14:53:37 +10:00
f300df5fd1
Plane: added FS_LONG_TIMEOUT and FS_SHORT_TIMEOUT parameters
...
this is to address the issue raised here:
http://diydrones.com/forum/topics/ardupilot-circle-mode
2013-07-12 11:56:04 +10:00
fc67f51901
Plane: added ACRO_ROLL_RATE and ACRO_PITCH_RATE parameters
...
default to 180 degrees/second, which seems reasonable
2013-07-11 09:10:41 +10:00
a5bda3ffef
Plane: changed to using a "aircraft parameters" structure
...
this structure can be passed to libraries to give them easy access to
critical user parameters
2013-07-04 16:56:57 +10:00
d62636d309
Plane: added new TECS altitude controller
...
Includes improvements to takeoff/launch detect logic to support hand
launching for X-8 flight
2013-07-04 16:56:57 +10:00
45f5d05bd2
Plane: enabled RELAY_* parameters
2013-06-25 12:44:26 +10:00
056e0ca40d
Plane: APM2 doesn't have channel 9 PWM output
2013-06-24 13:06:54 +10:00
93cd0f9a31
Plane: switch to new AP_Scheduler
...
this gives us more accurate task scheduling in ArduPlane, plus better
monitoring of task timing (via SCHED_DEBUG)
2013-06-04 13:34:58 +10:00
27bc0cdc2c
Plane: rename old channel_* globals
...
prevent the old "g." names from being used
2013-06-03 16:37:51 +10:00
fb9bf21522
Plane: allow channel mapping of first 4 channels
...
this makes it easier to support DSM and SBUS radios
2013-06-03 16:23:48 +10:00
cd55ed45e2
Plane: removed the old roll/pitch/yaw PID controllers
...
use the new controllers, with auto parameter conversion
2013-05-31 14:06:56 +10:00
c81421e275
Plane: added MIXING_GAIN parameter
...
this allows for the full range of output on both channels, but can
saturate
2013-05-25 18:28:13 +10:00
dd633fcf3f
Plane: make voltage and battery capacity failsafe settable at runtime
...
this also fixes issue #292
2013-05-22 20:33:57 +10:00
4e2b88f6e6
Plane: added ATT_CONTROLLER option to select attitude controller
...
set to 1 for the new APM_Control library
2013-05-05 21:51:09 +10:00
de3fcbc413
Plane: removed the MANUAL_LEVEL option
...
levelling on every startup is far too error prone. This was just
another parameter that everyone changed.
2013-04-29 14:19:53 +10:00
3d7a4d0e6e
Plane: added ELEVON_OUTPUT option
...
this is like the vtail mixer, but for elevons
2013-04-29 12:13:59 +10:00
0b8c2da4df
Plane: support 12 output channels on PX4
2013-04-25 20:10:53 +10:00
78538d0543
Plane: removed old HDNG2RLL PID control
...
not used with L1
2013-04-15 10:52:32 +10:00
70a186464b
Plane: added LEVEL_ROLL_LIMIT parameter
...
this replaces both TKOFF_HEAD_HOLD and RUDDER_STEER, allowing users to
instead select a roll limit for takeoff and landing
2013-04-12 21:59:52 +10:00
11eb0cfce1
Plane: update for new AP_Navigation controller class
...
this switches ArduPlane over to use the L1 navigation controller, via
a generic nav_controller object pointer.
Note that the nav_controller controls all types of navigation now,
including level flight and heading hold. This provides a cleaner
abstraction than the old method of special case navigation handling
Pair-Programmed-With: Paul Riseborough <p_riseborough@live.com.au>
2013-04-12 12:48:09 +10:00
406921faf1
Plane: added VTAIL_OUTPUT option
...
this allows for software vtail mixing
2013-04-05 15:22:11 +11:00
dfb14d760b
Plane: added HIL_SERVOS option
...
this allows for real servo output in HIL
2013-03-30 14:38:43 +11:00
7db7d7db77
Plane: change FBWB altitude control algorithm
...
this makes FBWB much less sensitive to airframe tuning. When the
elevator stick first goes neutral it locks in the current altitude as
the target altitude. When the elevator stick is off neutral, it moves
the target altitude in proportion to the elevator, at a rate goverened
by the new FBWB_CLIMB_RATE parameter
This prevents the aircraft from slowly drifting in altitude in FBWB,
and gives a more intuitive control mechanism for altitude.
Thanks to Chris Miser from Falcon UAV for help in designing this
change
2013-03-28 10:27:25 +11:00
f077f54e6a
Plane: added TKOFF_HEAD_HOLD option
...
this allows control over whether ArduPlane tries to hold heading
during auto takeoff. For hand launches it can be better to hold the
wings level and not attempt to hold heading during takeoff to prevent
the possibility of a stall during the climb out.
Thanks to Chris Miser from Falcon UAV for the feedback that led to
this option.
2013-03-27 10:27:14 +11:00
0a385cc0ff
Plane: added TKOFF_THR_MINACC option
...
this is used for triggering auto takeoff with a hand launched plane
2013-03-09 14:41:04 +11:00
9697ff5d6d
Plane: Added extra parameter to specify at what speed in auto-takeoff throttle should engage
...
This adds TKOFF_THR_MINSPD in m/s
2013-03-09 14:19:48 +11:00
e0e22b63a7
Plane: removed INPUT_VOLTS parameter
...
no longer needed
2013-03-08 10:01:33 +11:00
86f667f6cc
Plane: added new SERIAL0_BAUD parameter
...
this is useful on PX4
2013-01-13 07:39:40 +11:00
b6295c12e1
Plane: fixes for new AP_Relay interface
2013-01-02 10:18:45 +11:00
f8dec9ae4a
ArduPlane: fixes to use CONFIG_HAL_BOARD instead of CONFIG_APM_HARDWARE
2012-12-20 14:51:37 +11:00
92cd631ce5
Plane: added THR_PASS_STAB parameter
...
this allows direct passthru of throttle in STABILIZE and FBWA, which
is useful for nitro planes wher you have a throttle cut switch that
drops the throttle below normal minimum.
2012-11-26 23:33:05 +11:00
8f108e2eb3
APM: added AMP_OFFSET option
...
thanks to Alexey Kozin!
2012-11-21 13:34:27 +11:00
3aeaf2ece6
APM: k_param_imu is now unused
2012-11-20 18:32:27 +11:00
d9b4407e64
AP_InertialSensor: changes after review with Tridge.
...
sanity checking added to accelerometer calibration routine.
user feedback is sent using gcs_send_text_fmt instead of Serial.printf.
moved ins parameters to new eeprom number to avoid conflicts with older parameters.
other small changes including renaming of functions and parameters.
2012-11-07 19:21:15 +09:00
8652bfee8d
APM: added RSSI_PIN option for receiver RSSI
...
this allows you to configure the pin for receiver RSSI without
recompiling
2012-11-06 22:04:41 +11:00
07c291bb73
APM: fixed a comment typo
2012-10-16 17:21:04 +11:00
775489d658
ArduPlane: added BATT_VOLT_PIN and BATT_CURR_PIN parameters to allow support for new 3DR IV battery monitor
2012-10-13 20:51:41 +09:00
6bae5ecd51
APM: added THR_SUPP_MAN option
...
this allows for manual throttle control during auto throttle
suppression. This is useful for keeping a petrol engine idling before
takeoff
2012-09-22 20:17:06 +10:00
cebb67e1df
APM: removed the unused sonar code
...
when we start supporting a sonar we'll add a AP_Sonar library, like
AP_Airspeed
2012-09-19 19:35:22 +10:00
2324997e16
APM: added ALT_OFFSET parameter
...
useful to adjust for barometric pressure changes during a long flight
2012-09-19 16:23:25 +10:00
5c3595e0dc
APM: fixed throttle nudging
...
The nudge value depended on RC3_TRIM, which is not a reliable
value. It tried to only take effect when the throttle stick was above
50%, but if RC3_TRIM was high for some reason (say 1500) then it would
actually depress the throttle by a large amount, which could cause the
plane to stall.
This also adds a boolean option THROTTLE_NUDGE to allow disabling of
throttle nudging
2012-09-09 19:39:04 +10:00
164c60d25f
APM: added RUDDER_STEER option
...
when enabled, this uses only the rudder to steer during takeoff and
landing, using aileron only for levelling
2012-09-08 10:07:03 +10:00
96ea350143
APM: added XTRK_MIN_DIST option
...
this allows you to disable crosstrack correction on short legs
2012-09-08 10:06:44 +10:00
f6c3197cd2
APM: added new TELEM_DELAY parameter
...
number of seconds to delay telemetry
2012-08-30 08:59:39 +10:00
fce01464b1
APM: added ALT_CTRL_ALG parameter
...
this allows you to select different altitude control algorithms. The
current choices are for the default (automatic based on if airspeed is
available), or to force a non-airspeed algorithm
The idea is to make it possible to use airspeed for some things (like
wind speed, speed scaling) but not for alt control
2012-08-28 20:18:24 +10:00
c9cf483822
APM: added XTRK_USE_WIND parameter
...
when enabled this will use the wind estimation code to adjust the
navigation bearing, allowing the navigation code to cope with much
higher levels of wind while using a compass
2012-08-25 17:49:26 +10:00
d445482ace
APM: added optional use of new APM_Control library
...
thanks to Jon Challinger for the new controllers!
2012-08-22 12:45:14 +10:00
70048f3d6f
uncrustify ArduPlane/Parameters.h
2012-08-21 19:19:51 -07:00
5e690d5680
APM: added parameter FBWB_ELEV_REV
...
this fixes issue 343
2012-08-17 15:04:53 +10:00
ad73c229ab
APM: added LAND_FLARE_ALT and LAND_FLARE_SEC
...
these allow you to configure the altitude and time before touchdown to
flare the plane and lock the heading. Useful on larger planes.
2012-08-15 18:11:16 +10:00
1252ddfe0c
APM: rename RDRSTEER to WHEELSTEER
...
thanks to Jon for the suggestion
2012-08-15 16:28:59 +10:00
e26e8b3b67
APM: added RDRSTEER_ PID for steering on ground
...
this allows for rolling takeoff with steering, and use of rudder in
landing
2012-08-15 12:39:35 +10:00
2865434d02
APM: added 'OBC' failsafe module for ArduPlane
...
this adds FS_* parameters for setting up APM to follow the outback
challenge failsafe rules.
This includes:
- manual pin
- heartbeat pin
- waypoint for heartbeat failure
- waypoint for GPS failure
2012-08-15 12:39:34 +10:00
5498d347f3
APM: Added RST_MISSION_CH option
...
this allows a pilot to reset the mission using a transmitter
switch. Very useful for repeating a mission during testing
2012-08-09 10:33:16 +10:00
e133900c68
APM: Added STICK_MIXING option
...
this replaces the compile time option. Disabling during long distance
flights when the transmitter may be out of range is useful.
2012-08-09 08:53:29 +10:00
d34549f386
Add an optional second mount to ArduPlane and ArduCopter
2012-08-08 23:22:24 +02:00
5bfd1200d6
APM: change variables to use _cm, _cd and _ms suffix for units
...
this makes it less likely that we mix up units
2012-08-08 12:12:30 +10:00
a823c9ceae
APM: removed cli slider and dipswitch options
...
use mavlink/eeprom for all config
2012-08-08 12:12:29 +10:00
12cd6b68ff
AP_Param: update ArduPlane core for new AP_Param interface
2012-08-08 12:11:57 +10:00
b8c7b8a786
RC_Channel: Allow each channel to know who they are, this simplifies the enabling and output function calls.
2012-08-05 23:08:31 +02:00
6bcfe913f7
APM: added a SCALING_SPEED parameter
...
this allows users to adjust the base speed used for scaling roll/pitch
PIDs. This can be used to make PIDs work for both airspeed and
non-airspeed control
2012-07-26 11:30:23 +10:00
98237a0e00
Added Oilpan INS group object param
2012-07-18 23:07:50 -07:00
d02655ac56
APM: Fixed bug where landing_pitch wasnt initialized properly
...
this adds a new LAND_PITCH_CD parameter to control the landing pitch
when an airspeed sensor is not being used
2012-07-19 13:59:30 +10:00
d6e370886f
APM: rename airspeed_cruise to airspeed_cruise_cm to make the units clearer
...
it is in cm/s, not m/s
2012-07-19 11:50:41 +10:00
610fdeacc1
Support up to 11 servos in APM2
...
Conflicts:
ArduPlane/ArduPlane.pde
2012-07-18 22:01:19 +02:00
de3c9ce56d
Airspeed: change APM to use new AP_Airspeed library
...
the next step is AHRS dead reckoning
2012-07-16 11:21:50 +10:00
99b11e4f19
Mount: enable mount control via eeprom parameters
...
this enables MNT_* parameter control of the camera mount code. It also
fixes the conversion of calculated angles between degrees and
integers, and fixes stabilised mount control when yaw control is not
available.
2012-07-03 10:21:01 +10:00
55092c25a6
SITL: enable the SIM_* parameters in ArduCopter and ArduPlane
2012-06-29 15:10:52 +10:00
5bccfbd94c
Barometer: fixed airstart for APM
...
we need to re-load the ground pressure and temperature from eeprom on
and airstart
2012-06-27 16:01:50 +10:00
619bcc00d9
APM: parameter enums should not be conditionally compiled
2012-06-15 11:57:00 +10:00
0900751bcd
APM: added longer comment on k_format_version
2012-06-15 11:55:09 +10:00
6d2ac62006
Let's keep the same format version until CAMERA is activated by default
2012-06-13 21:28:13 +02:00
1906e06b69
Added camera trigger functionality
2012-06-13 21:00:20 +02:00
37d8f86d33
Added missing Manual Level initializer
2012-06-10 13:08:22 -07:00
5766afa6c8
ArduPlane: Increment format number in Parameters.h
...
* Force all users to reconfigure to take advantage of elevon patch
( 669e6867 )
2012-05-28 20:51:12 -07:00
b3aa704c49
AirSpeed: added parameter ARSPD_USE
...
setting ARSPD_ENABLE to 1 and ARSPD_USE to 0 allows the airspeed
sensor to be initialised and logged without it being used for flight
control. This is very useful when initially testing an airspeed sensor
in a new plane. It also makes it possible to enable/disable the use of
the airspeed sensor during a flight at any time.
2012-05-22 20:02:23 +10:00
d07b77237e
AHRS: enable AHRS_ group in ArduPlane
2012-04-16 20:55:13 +10:00
4c4c38f69a
APM: Added MANUAL_LEVEL option
...
when MANUAL_LEVEL is set to 1, we don't do accelerometer levelling at
startup, and instead used the values saved in the EEPROM. This makes
it easier to do levelling on the bench, or once for a series of
flights for the day
2012-03-29 12:39:53 +11:00
718a5b70e3
AP_Param: fixed saving of sensor calibration
...
this fixes the saving of the accel and gyro calibration to EEPROM,
which was initially broken by the AP_Param conversion
2012-02-18 10:51:57 +11:00
Andrew Tridgell
Michael Day
Randy Mackay
Paul Riseborough
Michael Warren
Pat Hickey
uncrustify
Amilcar Lucas
Jason Short
Jeff Taylor