f740f6e94d
APM: removed some config file cruft
...
these options are now settable via MAVLink
2012-03-18 13:34:40 +11:00
80b356367e
update AP version to 2.30
2012-03-18 10:27:49 +08:00
a203282779
correct small typos in comments
2012-03-11 21:30:09 +01:00
1e47ab26f2
AP_Declination: disable library when AUTOMATIC_DECLINATION is not ENABLED
...
unfortunately this library was causing avrdude to fail to load the hex
to my APM2. Until we work out why, it's disabled.
2012-03-11 21:46:41 +11:00
2e1cacd67f
AP_Declination: Added call to compass.set_initial_location if the compass is enabled when the 3D fix is obtained.
...
Signed-off-by: Andrew Tridgell <tridge@samba.org>
2012-03-11 20:59:47 +11:00
566bbed7ad
AP_Declination: Added new config value to allow the user to have the declination overwritten on every 3D fix.
...
Signed-off-by: Andrew Tridgell <tridge@samba.org>
2012-03-11 20:59:47 +11:00
f39d8dbde8
GCS: get_integrator() is now get_gyro_drift() in DCM
2012-03-10 10:34:33 +11:00
4f739ea28f
make 'ENABLE' and 'ENABLED' mean the same things
...
users get this wrong far too often!
2012-03-10 10:34:33 +11:00
d17a7e81e3
APM: removed quaternion special cases
2012-03-10 10:34:32 +11:00
3239a00b23
APM: avoid fetching the DCM matrix twice
...
also no special case for quaternions
2012-03-10 10:34:32 +11:00
04826065ef
Quaternion: show "Quaternion test" on startup if enabled
2012-03-10 10:34:29 +11:00
aa4beb9753
APM: make it possible to build ArduPlane with quaternion support
2012-03-10 10:34:29 +11:00
a54d6f744e
HWSTATUS: if we don't know the voltage, report it as zero
...
this will tell us if board_voltage() is really working
2012-03-10 10:34:28 +11:00
8e162ec35b
APM: fixed reset of control switch when short_fs_action is disabled
...
When FS_SHORT_ACTN is 0, we should not re-read the control switch
unless we changed mode on the initial short fs action
2012-03-10 10:34:28 +11:00
46c91fa0c4
APM: added logging of DCM, HWSTATUS and SIMSTATE
2012-03-10 10:34:27 +11:00
82dd1cd7ce
APM: added board_voltage() function
2012-03-02 15:48:27 +11:00
00180e7084
Cleanup: rename files with spaces in their names, replace with underscores
...
* Skipped /Tools/ArdupilotMegaPlanner/Resources/new...
and /archive/Configurator/Source/Utilities/TDMS/G...
because I don't want to mess with that.
2012-02-28 16:14:31 -08:00
630de04bd1
ArduPlane - updated to use new filter library
2012-02-28 21:03:04 +09:00
4501c488b4
ArduPlane - added Filter.h to unbreak the build!
2012-02-26 17:05:56 +09:00
6363da2829
ArduPlane - switch sonar to use new mode filter from filter library
2012-02-26 15:35:42 +09:00
3fe5b3151b
allow MAG_ENABLE to be changed in flight
...
this disables the compass in DCM if MAG_ENABLE is changed in
flight. Without this we would use a fixed yaw once the compass is
disabled
This also makes sure we don't pass the compass to DCM till we have
done a read. This ensures we have a good compass fix for the initial
DCM heading
2012-02-25 14:51:09 +11:00
17718720b1
GCS: force scalar type in copy_name()
...
this enables access to compass offsets over MAVLink
2012-02-25 11:37:20 +11:00
b231112957
DCM: renorm_sqrt_count is now called renorm_range_count
2012-02-23 08:16:08 +11:00
1fc24b506e
AP_Param: update users of AP_Param for ParamToken
2012-02-19 17:05:28 +11:00
b6fdf626e4
APM: expanded parameter area to match ACM
...
this ensures waypoints and basic eeprom layout remain in sync
2012-02-18 10:51:57 +11:00
6b357fc66b
AP_Param: fixed saving of sensor calibration
...
this fixes the saving of the accel and gyro calibration to EEPROM,
which was initially broken by the AP_Param conversion
2012-02-18 10:51:57 +11:00
8355823bc7
APM: use set_and_save_ifchanged() for GCS stream rates
...
this avoids a lot of EEPROM scan operations when the groundstation
updates the stream rates
2012-02-18 10:51:57 +11:00
f8ed9f0e8d
APM: Fix rudder in elevon mode.
...
elevon planes can have rudders too
2012-02-16 14:43:24 +11:00
2dcb594f4a
APM: changed hold_course for landing to be based on yaw_sensor
...
when we are in the final stages of a landing (less than 2 seconds from
landing waypoint, or less than 3m above landing altitude) we switch
the navigation to use a fixed course. The code previously used the
crosstrack_bearing for this, but this can lead to a large nav_roll in
this final stage of the approach, which can put a wing into the
runway. In autotest we were seeing a nav_roll value of -45 degrees as
we crossed the transition point for the landing, which often led to a
crash.
This changes the code to use the current yaw_sensor value instead,
which is much less likely to lead to large rolls in the final landing
stages.
2012-02-15 08:50:45 +11:00
c6b6320b43
APM: report the nav_bearing as hold_course when enabled
...
this gives a more accurate view of the navigation code, as when
hold_course is not -1 it overrides nav_bearing
2012-02-15 08:50:45 +11:00
252a2d0c9b
APM: added some comments related to hold_course
...
hold_course is either -1 (for disabled) or a course to hold for
takeoff/landing. This makes the code a bit clearer.
It also resets hold_course in all non-auto modes, to ensure it isn't
used
2012-02-15 08:50:45 +11:00
c93dedc955
when setting airspeed and groundspeed in a mission, don't save to EEPROM
...
If you include airspeed, throttle or groundspeed changes in a mission
then those should not be saved to EEPROM, as otherwise if you restart
and re-fly the mission you will be starting with different parameters
to the ones you used for the first flight.
This is particularly important for setting the target airspeed when
coming in for a landing. You typically set a low target, but if you
fly again the next day I think it would be a real surprise to find
that your loiter airspeed has then changed to the value from the
landing part of your last mission.
This one can be argued either way, but I think that not saving these
changes is the more conservative choice, and better fits the
'principal of least surprise'
2012-02-14 15:20:44 +11:00
df2ef6ff47
APM: fixed some build warnings
2012-02-14 08:58:56 +11:00
3907cf81f8
Mavlink: report the corrected pitch via MAVLink
...
this subtracts the TRIM_PITCH_CD from the pitch reported via
MAVLink. That gives a better indication of the true pitch in the tlog
2012-02-14 08:58:56 +11:00
da16ccf993
fixed some printf casts
2012-02-14 08:34:10 +11:00
c6f3f7065c
APM: the CLI fits nicely on the 1280 again now
...
I find the CLI very useful for testing, so enable it by default on the
1280. Logging is still off by default.
2012-02-14 08:33:49 +11:00
153575a01c
token is 16 bits now
2012-02-13 16:22:53 +11:00
16a5b5c3ee
added AP_Param::show_all()
...
this moves the logic into common code
2012-02-13 16:22:52 +11:00
781617cae0
token size for first()/next() is now 16 bits
2012-02-13 16:22:52 +11:00
50f9d12ad5
go back to 1024 bytes for variables in EEPROM
2012-02-13 16:22:52 +11:00
f5f6e2d4ec
added group indexes to GCS_MAVLINK class
2012-02-13 16:22:52 +11:00
a8140d9524
expand parameter area for ArduPlane
...
this ensures all parameters can be saved without overflow
2012-02-13 16:22:52 +11:00
bbc876fcdf
tidy up a comment
2012-02-13 16:22:52 +11:00
9fe8c079e7
fixed two parameter names
2012-02-13 16:22:51 +11:00
922139b824
expose mavlink stream rates as parameters
2012-02-13 16:22:51 +11:00
edfb8fe0b7
imported new Parameters code to APM
2012-02-13 16:22:51 +11:00
c4bd17052e
import new Parameters.h for AP_Param to APM
2012-02-13 16:22:51 +11:00
ab057d9801
implement dump of all vars in CLI using AP_Param
2012-02-13 16:22:51 +11:00
faa098b2b6
adapt mainline APM code to AP_Param
2012-02-13 16:22:51 +11:00
3932e8b2a1
Battery monitor type 3 cannot calculate battery remaining properly, due it uses only voltage reading. This path set battery_remaining to a value out-of-band for that type of monitoring. It informs to external devices to not show that info.
2012-02-11 21:01:13 -02:00
Andrew Tridgell
Michael Oborne
Amilcar Lucas
Adam M Rivera
Pat Hickey
rmackay9
Phil
Sandro Benigno