3995381800
Arducopter.pde: Moved gps to 10hz. Changed calc_XY_velocity to calc_GPS_velocity.
2012-04-18 23:07:35 -05:00
c7c6dd70b9
navigation.pde: Added calc_GPS_velocity. Added constraint to x/y error and x/y rate error.
2012-04-18 23:06:15 -05:00
ccb21613b5
ArduCopter - updated firmware version to "2.6 Beta"
2012-04-14 14:26:44 +09:00
33bd558a94
ArduCopter - LEDS - main code to support COPTER_LEDS.
...
Code by Robert Lefebvre
2012-04-12 22:55:44 +09:00
a429c78d20
ArduCopter - LEDS - set new output pins to OUTPUT to support COPTER_LEDS.
...
Code by Robert Lefebvre
2012-04-12 22:55:40 +09:00
663eda6d47
ArduCopter - LEDS - define pins to be used for COPTER_LEDS.
...
Code by Robert Lefebvre
2012-04-12 22:55:36 +09:00
ac9555a3b4
ArduCopter - LEDS - added new COPTER_LEDS definition
...
Code by Robert Lefebvre
2012-04-12 22:55:32 +09:00
d1a5d1f94c
ArduCopter - LEDS - two new parameters to support COPTER_LEDS.
...
Code by Robert Lefebvre.
2012-04-12 22:55:28 +09:00
8f0bc57967
ArduCopter - navigation.pde - added logging of Loiter PID controllers
2012-04-11 23:52:25 +09:00
023378a214
ArduCopter - Parameters.h - changed initialisation order to remove compiler warning (have not changed enum values so shouldn't require eeprom format id update)
2012-04-09 17:37:06 +09:00
c7edd7857c
ArduCopter - added dataflash logging of roll and pitch rate controllers
2012-04-08 10:19:20 +09:00
0607be8ea5
ArduCopter - removed unused motor pde files including heli.pde, motors_hexa.pde, motors_octa.pde, motors_octa_quad.pde, motors_tri.pde and motors_y6.pde
2012-04-04 23:06:12 +09:00
2128085576
ArduCopter - test.pde - changed references "motor_armed" to "motors.armed()" as part of move to AP_Motors library.
...
Change to ESC initialisation calls to use motors.throttle_pass_through method of AP_Motors class.
2012-04-04 23:05:26 +09:00
2fc3b740c4
ArduCopter - system.pde - changed references to "motor_armed" to "motors.armed()" as part of the move to use AP_Motors library.
2012-04-04 23:03:21 +09:00
5e2147de1f
ArduCopter - setup.pde - changed cli for helicopter to call the new AP_Motors class's parameters instead of the global parameters.
...
changed init_esc to call the AP_Motor's class's "throttle_pass_through" function.
2012-04-04 23:02:29 +09:00
1701cac0b1
ArduCopter - radio.pde - changed motor initialisation to set update rate, frame orientation, min and max throttle to AP_Motors class.
...
Note: perhaps the motors speed at least should be moved to a parameter within the motors class.
output_min function greatly simplified as this is handled by the AP_Motors class.
2012-04-04 23:00:56 +09:00
0f4203a755
ArduCopter - motors.pde - changed references to "motor_armed" to "motors.armed()" because we've moved to using the AP_Motors class.
...
Simplified set_servos_4 function which was responsible for calling "output_motors_armed" or "output_motors_disarmed" as this determination as to whether the motors are armed or not is handled within the AP_Motors class.
2012-04-04 22:58:42 +09:00
00d540bfa9
ArduCopter - leds.pde - changed refrences to "motor_armed" to "motors.armed()"
2012-04-04 22:57:50 +09:00
ffd77f58ab
ArduCopter - removed references to MOT_1 etc as these are now within the AP_Motors class (i.e. MOT_1 has become AP_MOTORS_MOT_1)
2012-04-04 22:56:07 +09:00
929e933b69
ArduCopter - increased firmware version to 118. Removed nearly all heli parameters as these are all created by the AP_MotorHeli class now.
...
Note: we cannot move the heli_servos to the AP_MotorHeli class yet because of a small issue in the parameters class.
2012-04-04 22:55:07 +09:00
acc24291f3
ArduCopter - Log.pde - changed MOT output to dataflash to take values from AP_Motors class's motor_out array instead of the global motor_out array.
2012-04-04 22:53:21 +09:00
86d2a9ffdb
ArduCopter - GCS_Mavlink.pde - changed output to ground station to use new AP_Motor's class motors array inplace of the global "motor_out" array.
2012-04-04 22:52:26 +09:00
23c3f25654
ArduCopter - Attitude.pde - moved heli_get_angle_boost from heli.pde (which will be removed) to Attitude.pde. In fact we should combine heli_get_angle_boost and the regular get_angle_boost.
2012-04-04 22:51:39 +09:00
544237d60a
ArduCopter - add includes for new AP_Motors classes.
...
Remove global motor_filtered and motor_out arrays.
Removed all global heli variables.
replace "motor_armed" with "motors.armed()"
removed output to rc_4 for tri because this is now handled by AP_MotorsTri class
2012-04-04 22:50:43 +09:00
40d7b07789
MAVLink: port the new adaptive flow control to ArduCopter
...
This allows for arbitrary stream rates, and supports flow control if
you are using a 3DR radio
2012-04-02 11:18:53 +10:00
b0c9a25024
ArduCopter - CH6 tuning - changed Roll/Pitch Rate D tuning to use the user supplied tuning range instead of the range / 100.
...
also changed heli_ext_gyro_gain to make it use the tuning range directly.
2012-03-31 09:28:25 +09:00
1e0a2fb0be
MAVLink: don't waste 100 bytes of bandwidth sending 1 byte of information
...
the GPS_STATUS message is a massive waste of bandwidth, but it is the
only message that tells us the number of visible satellites. So only
send it if that information changes.
This makes MAVLink work better at low baud rates
2012-03-30 17:46:20 +11:00
0985327331
ACM: use set_blocking_writes(false) when we arm motors
2012-03-30 17:46:20 +11:00
36e741b078
MAVLink: raise the serial transmit buffer size to 256 bytes
...
the 128 byte serial transmit buffer was causing significant problems
with queueing of mavlink messages. With 256 bytes we can fit a lot
more messages out in each pass of the code, which makes telemetry more
efficient
As we discussed on the dev call, we now have enough free ram for this
to be worthwhile
2012-03-30 17:46:20 +11:00
58f539ca35
ACM: removed FORCE_AUTOMATIC_DECLINATION_UPDATE
...
we now have the EEPROM option COMPASS_AUTODEC instead
2012-03-30 14:25:27 +11:00
0727955fe3
ArduCopter: Changed implementation of configuration value for automatic declination. There is now a FORCE_AUTOMATIC_DECLINATION_UPDATE that when enabled will update the declination on every GPS 3D fix regardless of whether or not the user saved a value to the EEPROM. By default the declination will only be set by the automatic declination routine if the user has not saved a declination to the EEPROM.
2012-03-30 14:25:06 +11:00
a12a7a7d87
ArduCopter - added CH6_STABILIZE_KD tuning value
2012-03-29 21:09:41 +09:00
2cc87af180
Added multiple new tuning parameters to the inflight channel 6 tuning feature:
...
#define CH6_YAW_KI 24
#define CH6_ACRO_KP 25
#define CH6_YAW_RATE_KD 26
#define CH6_LOITER_KI 27
#define CH6_LOITER_RATE_KI 28
2012-03-28 23:58:58 +09:00
8ccf3a05f0
Mavlink: fixed warnings about limits on int32 values
2012-03-27 15:37:25 +11:00
409c147ce3
ACM: fixed heli build
2012-03-27 15:37:25 +11:00
5d7c571fb1
ACM: fixed the build on the 1280
2012-03-27 15:37:24 +11:00
4821eb4807
ACM: enable the new compass offset nulling in ACM
2012-03-27 15:37:24 +11:00
441413f1c6
ArduCopter - added PID log type. Implemented for Yaw stabilize and rate controllers.
2012-03-25 16:09:08 +09:00
eb55234809
ArduCopter - updated firmware version to 2.5.3
2012-03-25 09:13:51 +09:00
1f253c5217
ArduCopter - altitude hold - ensure throttle_avg is initialised from g.throttle_cruise parameter
2012-03-23 23:48:24 +09:00
19981d4864
ArduCopter - updated to firmware version to 2.5.2 to avoid confusion with post 2.5.1 versions posted to downloads area
2012-03-23 23:12:49 +09:00
872ec65afa
Fix Auto_Trim to allow it to actually be called when setup on Ch7 pulldown menu in MP.
2012-03-23 09:17:58 -04:00
74893f6959
Throttle_hold was in APM_Config - which is ignored by the Mission planner Hex generator
2012-03-22 10:01:24 -07:00
be22deb56f
ArduCopter - motors_quad.pde - corrected test sequence for + configuration
2012-03-21 22:04:50 +09:00
7dc18b53ad
ArduCopter - navigation - corrected comment in check_missed_wp function to clarify that you've passed the waypoint when the direction to the way point is more than 100 degrees off (not 10 degrees off) from your original bearing towards the waypoint
2012-03-20 17:11:22 +09:00
198ac97914
ArduCopter - updated version to 2.5.1
2012-03-20 17:08:18 +09:00
0ba48a8556
ArduCopter - increased default THROTTLE_CRUISE to 450
2012-03-20 16:34:07 +09:00
ce6b1ccc75
ArduCopter - Navigation.pde - corrected comment re wp_distance and get_distance to clarify that they are in cm (not meters!)
2012-03-20 16:13:38 +09:00
dc71191f25
MAVLink: constrain variable changes to the datatype range
...
if someone tries to set a AP_Int16 to a value of 300000, they now get
32767 instead of -27678
2012-03-19 17:29:02 +11:00
690ad58a64
AHRS: adapt ArduCopter for new AHRS framework
2012-03-19 17:29:02 +11:00
Adam M Rivera
rmackay9
Andrew Tridgell
Robert Lefebvre
Jason Short