Andrew Tridgell
edad43611d
Plane: reset last heartbeat time on startup completion
...
this gives more time for the GCS to send its first heartbeat
2012-12-26 08:46:36 +11:00
Andrew Tridgell
feca411943
Plane: added new TRAINING mode
...
this mode gives manual control when the roll or pitch is within the
set limits (the same limits as FBW mode), and prevents the pilot from
flying beyond those limits, essentially a "attitude limited manual"
mode
2012-12-20 22:41:58 +11:00
Pat Hickey
f8dec9ae4a
ArduPlane: fixes to use CONFIG_HAL_BOARD instead of CONFIG_APM_HARDWARE
2012-12-20 14:51:37 +11:00
Pat Hickey
92b0c302f2
ArduPlane: Ported to AP_HAL
2012-12-20 14:51:36 +11:00
Andrew Tridgell
84300c85d6
APM: make it possible to run the CLI on any serial port
2012-11-21 21:41:34 +11:00
Andrew Tridgell
fcbd3a823b
APM: added a new type of auxilary aileron, with rc input
...
a AileronWithInput assumes you have setup your RC transmitter to give
the right trim and input on the secondary aileron
2012-11-21 13:34:26 +11:00
Andrew Tridgell
c8e84d18a4
APM: tidy up a comment
2012-09-16 15:51:13 +10:00
Andrew Tridgell
feb3fe77ce
APM: simplify radio_trim code
...
this removes the duplicate code. Throttle trim is not changed.
2012-09-09 19:39:09 +10:00
Andrew Tridgell
5c3595e0dc
APM: fixed throttle nudging
...
The nudge value depended on RC3_TRIM, which is not a reliable
value. It tried to only take effect when the throttle stick was above
50%, but if RC3_TRIM was high for some reason (say 1500) then it would
actually depress the throttle by a large amount, which could cause the
plane to stall.
This also adds a boolean option THROTTLE_NUDGE to allow disabling of
throttle nudging
2012-09-09 19:39:04 +10:00
Andrew Tridgell
49468953a3
APM: updated for new RC_Channel_aux API
2012-09-08 15:14:41 +10:00
Andrew Tridgell
fce01464b1
APM: added ALT_CTRL_ALG parameter
...
this allows you to select different altitude control algorithms. The
current choices are for the default (automatic based on if airspeed is
available), or to force a non-airspeed algorithm
The idea is to make it possible to use airspeed for some things (like
wind speed, speed scaling) but not for alt control
2012-08-28 20:18:24 +10:00
uncrustify
43991712be
uncrustify ArduPlane/radio.pde
2012-08-21 19:19:50 -07:00
rmackay9
360c1198a6
ArduPlane: more "int" to "int16_t" and added cast to (int) in printf statements.
...
Also modified dump_log function's last_log_num to be int16_t which matches return type from DataFlash's find_last_log method.
2012-08-18 18:55:14 +09:00
Andrew Tridgell
e2c8ec2c9e
APM: removed THROTTLE_REVERSE option
...
Better to use RC3_REV
2012-08-09 10:04:44 +10:00
Andrew Tridgell
5bfd1200d6
APM: change variables to use _cm, _cd and _ms suffix for units
...
this makes it less likely that we mix up units
2012-08-08 12:12:30 +10:00
Andrew Tridgell
a823c9ceae
APM: removed cli slider and dipswitch options
...
use mavlink/eeprom for all config
2012-08-08 12:12:29 +10:00
Amilcar Lucas
b8c7b8a786
RC_Channel: Allow each channel to know who they are, this simplifies the enabling and output function calls.
2012-08-05 23:08:31 +02:00
Amilcar Lucas
9c1ac2d9e6
More work on ch9, 10 and 11
2012-08-04 19:44:41 +02:00
Amilcar Lucas
bbc4bdb729
More flexible RC support
2012-08-04 18:39:20 +02:00
Andrew Tridgell
d6e370886f
APM: rename airspeed_cruise to airspeed_cruise_cm to make the units clearer
...
it is in cm/s, not m/s
2012-07-19 11:50:41 +10:00
Amilcar Lucas
610fdeacc1
Support up to 11 servos in APM2
...
Conflicts:
ArduPlane/ArduPlane.pde
2012-07-18 22:01:19 +02:00
Andrew Tridgell
de3c9ce56d
Airspeed: change APM to use new AP_Airspeed library
...
the next step is AHRS dead reckoning
2012-07-16 11:21:50 +10:00
Andrew Tridgell
b3aa704c49
AirSpeed: added parameter ARSPD_USE
...
setting ARSPD_ENABLE to 1 and ARSPD_USE to 0 allows the airspeed
sensor to be initialised and logged without it being used for flight
control. This is very useful when initially testing an airspeed sensor
in a new plane. It also makes it possible to enable/disable the use of
the airspeed sensor during a flight at any time.
2012-05-22 20:02:23 +10:00
Phil
9242c157ee
APM: Fix rudder in elevon mode.
...
elevon planes can have rudders too
2012-02-16 14:43:24 +11:00
Pat Hickey
dfece8e3ff
ArduPlane: Call APM_RC.enable_out for all channels in init_rc_out.
2012-01-22 12:03:11 -08:00
Pat Hickey
4015cb0a40
purple: fixed APM_RC.Init() to add isr_registry parameter
2011-11-25 20:00:17 -08:00
Jason Short
326cfef808
Dead Zone fix - Now the range is full instead of clipped. Should make the Yaw much more smooth.
2011-09-26 22:12:39 -07:00
Amilcar Lucas
dca013965a
Fix issue #285
2011-09-25 11:36:31 +02:00
Andrew Tridgell
4437ff1046
get rid of the last active uses of the SendDebug macros
...
please use gcs_send_text*() from now on, to ensure serial queueing
2011-09-19 11:04:02 +10:00
Amilcar Lucas
1f29197771
Revert more of 6dcbc7f44bc0.
...
Fix an issue with initialization of channels that on-line changed their function.
For the curious people that the code size overhead of having any aux channel do any function (with this code) is 44 bytes.
To see wich code I'm talking about, do a git diff 05057ac2d455..this_commit (replace this commit with the commit hash of this commit)
2011-09-13 14:01:35 +02:00
Amilcar Lucas
5406991831
Added support for routing any function to any of the aux. servos.
...
This is a manual merge from the APM_Camera branch.
It reverts the stuff that Oliver did not menat to do with his commit 6dcbc7f44bc0
2011-09-13 01:24:06 +02:00
Doug Weibel
f05f56f83f
Correct bug in initialization of auxiliary channels
...
The value of aux_servo_function[CH_x] was not being set before the radio init_rc_in() function was setting channel angle/range.
2011-09-12 20:21:12 +02:00
Amilcar Lucas
77c798abd5
Use G_RC_AUX macro to simplify accessing the auxiliary servos
2011-09-12 00:02:47 +02:00
Amilcar Lucas
ce010b4e38
Moved update_aux_servo_function() to the RC_Channel_aux.* files.
...
This simplifies code sharing between ArduCopter and Arduplane at the expense of 48bytes.
Moved CH_x defines out of the defines.h file and into the library where they belong
2011-09-11 23:07:30 +02:00
Amilcar Lucas
93cbe664d6
Only run camera code if camera support is enabled
2011-09-11 17:41:18 +02:00
Amilcar Lucas
b36d0352f3
Added a comment about lower half of the array
2011-09-10 23:58:25 +02:00
Amilcar Lucas
d3280bdd16
Added comments explaining when should the function be used
2011-09-10 23:36:47 +02:00
Amilcar Lucas
59cbb8ec6f
Moved a camera mount function call, out of the servos update function
2011-09-10 13:47:09 +02:00
Amilcar Lucas
f4998c3673
Moved a function from radio.pde to the RC_Channel_aux library. Now its more readable and reusable
2011-09-10 13:26:29 +02:00
Amilcar Lucas
b7a0d8836a
This is the real HEAD of the APM_Camera branch. Seams that lots of changes got lost in the SVN to GIT port
2011-09-09 16:18:38 +02:00
Andrew Tridgell
609ae8359d
import APM_Camera branch from SVN
2011-09-09 11:45:13 +10:00
Andrew Tridgell
e0dc1271d6
imported ArduPlane from ArduPilotMega svn
2011-09-09 11:29:39 +10:00