2018-09-20 12:25:51 -03:00
|
|
|
# hw definition file for processing by chibios_hwdef.py
|
|
|
|
|
# for Furious FPV F35 Lightning type hardware
|
|
|
|
|
|
|
|
|
|
# MCU class and specific type
|
|
|
|
|
MCU STM32F4xx STM32F405xx
|
|
|
|
|
|
|
|
|
|
# board ID for firmware load
|
|
|
|
|
APJ_BOARD_ID 135
|
|
|
|
|
|
|
|
|
|
# crystal frequency
|
|
|
|
|
OSCILLATOR_HZ 8000000
|
|
|
|
|
|
|
|
|
|
# ChibiOS system timer
|
|
|
|
|
STM32_ST_USE_TIMER 5
|
|
|
|
|
|
|
|
|
|
# flash size
|
|
|
|
|
FLASH_SIZE_KB 1024
|
|
|
|
|
FLASH_RESERVE_START_KB 64
|
|
|
|
|
|
|
|
|
|
# console
|
|
|
|
|
#STDOUT_SERIAL SD1
|
|
|
|
|
#STDOUT_BAUDRATE 57600
|
|
|
|
|
|
|
|
|
|
# order of I2C buses
|
|
|
|
|
I2C_ORDER I2C1
|
|
|
|
|
|
|
|
|
|
# order of UARTs (UART3RX used for RCInput, UART4RX and USART6RX not pinned out)
|
2020-04-24 08:10:08 -03:00
|
|
|
SERIAL_ORDER OTG1 USART1 UART5 USART2 EMPTY UART4 USART6
|
2018-09-20 12:25:51 -03:00
|
|
|
|
|
|
|
|
# USB sensing
|
|
|
|
|
#PA9 VBUS INPUT OPENDRAIN
|
|
|
|
|
|
|
|
|
|
# USB
|
|
|
|
|
PA11 OTG_FS_DM OTG1
|
|
|
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
|
|
|
|
|
|
# UART1 (telem1)
|
|
|
|
|
PA9 USART1_TX USART1
|
|
|
|
|
PA10 USART1_RX USART1
|
|
|
|
|
|
|
|
|
|
# UART2 (GPS)
|
|
|
|
|
PA2 USART2_TX USART2
|
|
|
|
|
PA3 USART2_RX USART2
|
|
|
|
|
|
|
|
|
|
# UART3RX (RCInput)
|
2021-10-10 18:28:57 -03:00
|
|
|
PB11 TIM2_CH4 TIM2 RCININT PULLDOWN LOW
|
2018-09-20 12:25:51 -03:00
|
|
|
PA8 SBUS_INVERT_RX OUTPUT
|
|
|
|
|
|
|
|
|
|
# UART4 (user), only TX pinned out
|
|
|
|
|
PA0 UART4_TX UART4
|
|
|
|
|
PC11 UART4_RX UART4
|
|
|
|
|
|
|
|
|
|
# UART5 (telem2)
|
|
|
|
|
PC12 UART5_TX UART5
|
|
|
|
|
PD2 UART5_RX UART5
|
|
|
|
|
|
|
|
|
|
# USART6 (user), only TX pinned out as "SPO" pin with hw inverter
|
|
|
|
|
PC6 USART6_TX USART6
|
|
|
|
|
PC7 USART6_RX USART6
|
|
|
|
|
|
|
|
|
|
# ADCs
|
|
|
|
|
PC1 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
|
|
|
PC2 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
|
PC3 RSSI_IN ADC1 SCALE(2)
|
|
|
|
|
define BOARD_RSSI_ANA_PIN 13
|
|
|
|
|
# also could be used as analog airspeed input
|
|
|
|
|
#PC3 PRESSURE_SENS ADC1 SCALE(2)
|
|
|
|
|
|
|
|
|
|
# VDD sense pin
|
|
|
|
|
#PA4 VDD_5V_SENS ADC1 SCALE(2)
|
|
|
|
|
|
|
|
|
|
# LED
|
|
|
|
|
PC10 LED OUTPUT HIGH GPIO(57)
|
|
|
|
|
define HAL_GPIO_A_LED_PIN 57
|
|
|
|
|
|
|
|
|
|
# SPI
|
|
|
|
|
PA5 SPI1_SCK SPI1
|
|
|
|
|
PA6 SPI1_MISO SPI1
|
|
|
|
|
PA7 SPI1_MOSI SPI1
|
|
|
|
|
|
|
|
|
|
PB13 SPI2_SCK SPI2
|
|
|
|
|
PB14 SPI2_MISO SPI2
|
|
|
|
|
PB15 SPI2_MOSI SPI2
|
|
|
|
|
|
|
|
|
|
PB3 SPI3_SCK SPI3
|
|
|
|
|
PB4 SPI3_MISO SPI3
|
|
|
|
|
PB5 SPI3_MOSI SPI3
|
|
|
|
|
|
|
|
|
|
# CS pins
|
|
|
|
|
PC0 MPU9250_CS CS
|
|
|
|
|
PA4 OSD_CS CS
|
|
|
|
|
PC5 BMP280_CS CS
|
|
|
|
|
#PB12 SDCARD_CS CS
|
|
|
|
|
|
|
|
|
|
PC4 MPU9250_DRDY INPUT
|
|
|
|
|
|
|
|
|
|
# These are the pins for SWD debugging with a STlinkv2 or black-magic probe.
|
|
|
|
|
#PA13 JTMS-SWDIO SWD
|
|
|
|
|
#PA14 JTCK-SWCLK SWD
|
|
|
|
|
|
|
|
|
|
# passive buzzer disabled, optional timers 2 and 5 used for RCinput and STM32
|
|
|
|
|
# PA1 TIM2_CH2 TIM2 GPIO(77) ALARM
|
|
|
|
|
|
|
|
|
|
# use active buzzer instead
|
|
|
|
|
PA1 BUZZER OUTPUT GPIO(80) LOW
|
|
|
|
|
define HAL_BUZZER_PIN 80
|
2023-04-22 18:11:08 -03:00
|
|
|
|
2023-04-21 10:26:50 -03:00
|
|
|
|
2018-09-20 12:25:51 -03:00
|
|
|
|
|
|
|
|
# I2C
|
|
|
|
|
PB6 I2C1_SCL I2C1
|
|
|
|
|
PB7 I2C1_SDA I2C1
|
|
|
|
|
|
|
|
|
|
# PWM pins S1-S6
|
|
|
|
|
PC8 TIM8_CH3 TIM8 PWM(1) GPIO(50)
|
|
|
|
|
PC9 TIM8_CH4 TIM8 PWM(2) GPIO(51)
|
|
|
|
|
PB8 TIM4_CH3 TIM4 PWM(3) GPIO(52)
|
|
|
|
|
PB9 TIM4_CH4 TIM4 PWM(4) GPIO(53)
|
|
|
|
|
PB0 TIM3_CH3 TIM3 PWM(5) GPIO(54)
|
|
|
|
|
PB1 TIM3_CH4 TIM3 PWM(6) GPIO(55)
|
|
|
|
|
|
2020-09-01 02:43:56 -03:00
|
|
|
# SPI device table, note that the 9250 is not reliable at 8MHz on this board
|
|
|
|
|
SPIDEV mpu9250 SPI3 DEVID1 MPU9250_CS MODE3 4*MHZ 4*MHZ
|
2018-09-20 12:25:51 -03:00
|
|
|
SPIDEV bmp280 SPI3 DEVID2 BMP280_CS MODE3 1*MHZ 8*MHZ
|
|
|
|
|
SPIDEV osd SPI1 DEVID1 OSD_CS MODE0 10*MHZ 10*MHZ
|
|
|
|
|
#SPIDEV sdcard SPI2 DEVID1 SDCARD_CS MODE0 400*KHZ 25*MHZ
|
|
|
|
|
|
2019-05-29 23:17:50 -03:00
|
|
|
# one IMU
|
|
|
|
|
IMU Invensense SPI:mpu9250 ROTATION_YAW_90
|
2018-09-20 12:25:51 -03:00
|
|
|
|
2019-05-29 23:17:50 -03:00
|
|
|
# one baro
|
|
|
|
|
BARO BMP280 SPI:bmp280
|
|
|
|
|
|
2019-09-01 21:09:00 -03:00
|
|
|
# probe external compasses plus one in 9250
|
|
|
|
|
COMPASS AK8963:probe_mpu9250 0 ROTATION_YAW_90
|
2018-09-20 12:25:51 -03:00
|
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
|
|
|
define HAL_I2C_INTERNAL_MASK 0
|
|
|
|
|
|
|
|
|
|
# no onboard SD, filesystem support disabled until flash logging implemented
|
|
|
|
|
#define HAL_OS_FATFS_IO 1
|
|
|
|
|
|
|
|
|
|
# OSD support
|
2019-12-20 13:46:24 -04:00
|
|
|
define OSD_ENABLED 1
|
2018-10-31 21:10:21 -03:00
|
|
|
define HAL_OSD_TYPE_DEFAULT 1
|
2018-09-20 12:25:51 -03:00
|
|
|
ROMFS_WILDCARD libraries/AP_OSD/fonts/font*.bin
|
|
|
|
|
|
|
|
|
|
# available storage
|
|
|
|
|
define HAL_STORAGE_SIZE 15360
|
2021-10-27 02:32:43 -03:00
|
|
|
STORAGE_FLASH_PAGE 1
|
2018-09-20 12:25:51 -03:00
|
|
|
|
|
|
|
|
# defaults for battery monitoring
|
2018-10-31 07:26:09 -03:00
|
|
|
define HAL_BATT_MONITOR_DEFAULT 4
|
2018-09-20 12:25:51 -03:00
|
|
|
define HAL_BATT_VOLT_PIN 11
|
|
|
|
|
define HAL_BATT_CURR_PIN 12
|
|
|
|
|
define HAL_BATT_VOLT_SCALE 11
|
2018-10-23 11:42:35 -03:00
|
|
|
define HAL_BATT_CURR_SCALE 25
|
2020-08-18 15:47:39 -03:00
|
|
|
|
2020-09-01 02:43:56 -03:00
|
|
|
# enable IMU fast sampling
|
|
|
|
|
define HAL_DEFAULT_INS_FAST_SAMPLE 1
|
2023-07-07 05:11:17 -03:00
|
|
|
|
2023-10-18 11:17:06 -03:00
|
|
|
# no space for bootloader in firmware image:
|
2023-10-25 05:25:43 -03:00
|
|
|
include ../include/minimize_fpv_osd.inc
|
2023-10-18 11:17:06 -03:00
|
|
|
include ../include/no_bootloader_DFU.inc
|
