dark0707
/
px4-firmware
forked from Archive/PX4-Autopilot
1
0
Fork 0
Code Pull Requests Activity
35,559 Commits 514 Branches 136 Tags 234 MiB
Commit Graph

189 Commits

Author SHA1 Message Date
David Sidrane 62fd132047 boards:Use inttypes 
nxp_ucans32k146:Fix constant

spracing_h7extreme:Use inttypes
 2021-06-16 17:07:47 +02:00
echoG 6bc09138c1
Adding BatMon smart battery as a module and refactoring SMBUS based SBS 1.1 spec to a library 2021-06-09 12:17:45 -04:00
Daniel Agar 5f775b508f boards: enable CONFIG_OTG_ID_GPIO_DISABLE on all F7/H7 2021-06-01 15:19:15 -04:00
David Sidrane 32e92ba817 Revert:Pull downs - bad levels cause motor spins 2021-06-01 15:18:47 -04:00
David Sidrane 3e18fa12d6 px4_fmu-v5x:Remove vcm1193l 2021-05-26 13:41:10 -04:00
David Sidrane 2feb096fb9 vtrantech Rename to match V1.1 vcm5883->vcm1193l 2021-05-26 11:24:11 -04:00
David Sidrane 4acc18ca60 Add VCM5883 Magnetometer 
Fix LSB/G
 2021-05-18 12:57:46 -04:00
Daniel Agar c3884b5bc1
fake_imu (formally fake_gyro) updates for testing gyro filtering 
- fake_imu now publishes sine sweeps over 10 seconds
 - accel is also published so that fake IMU can be selected when the only option
 2021-05-17 20:26:25 -04:00
David Sidrane e87a6c755d px4_fmu-v5x:Add support for Revision 2 FMUM HW using ICM20649 not BMI088 2021-05-10 09:11:50 +02:00
David Sidrane baa37c1143 px4_fmu-v5x: Disable OTG_ID_GPIO 2021-05-05 20:48:06 +02:00
David Sidrane 7dd57d55f6 px4_fmu-v5x: Initalize PWM as input with Pull Downs 2021-05-05 20:48:06 +02:00
Daniel Agar 58b40fbbb9 boards: move testing to dedicated test variants 2021-04-14 09:21:31 +02:00
Daniel Agar ad934b4911
icm20948 i2c passthrough driver for ak09916 magnetometer (Here+ GPS/compass) 
- include icm20948 on most boards by default
 - create more test variants for default boards near flash limit (cuav_nora_test, cuav_x7pro_test, holybro_durandal-v1_test)
 2021-04-04 21:18:16 -04:00
Nico van Duijn 8d3335906a v5x: use low bandwidth mavlink mode 
This changes the default mavlink message set from onboard to
onboard_low_bandwidth, which drastically reduces the bandwidth required to get a
usable connection.
 2021-04-01 07:28:43 +02:00
Daniel Agar 6874e9fba0 boards: NuttX disable all NSH memory debug commands (mb, mh, mw) by default 
- closes https://github.com/PX4/PX4-Autopilot/issues/17062
 2021-03-30 09:23:43 -04:00
Daniel Agar 631d1647d3 boards: minimize unnecessary differences in default variants 2021-03-28 14:46:47 -04:00
dino 6d04a67b02 Moving define to microhal.h files, for each ST architecture. Correct channels were verified with ST_CUBE header files. For the H7 its a simplification for the current used H7x3. Other devices in that family expect the temperarture on channel 18. 
F1: channel 16
F3: channel 16
F4: channel 18
F7: channel 18
H7: channel 17, on STMf32Hx3
 2021-03-18 06:13:24 -07:00
dino 3c77ef7eb3 Fixed adc config, to read internal reference to get cpu temperature 2021-03-18 06:13:24 -07:00
Daniel Agar 4b99bd2077 boards: remove optional external ADIS IMUs to save flash 2021-03-15 13:37:24 -04:00
Daniel Agar edd42cfa86 boards: px4/fmu-v5x disable optional external IMU drivers 2021-03-15 11:16:38 -04:00
Daniel Agar 2257c3767e simple gyro auto calibration module 2021-03-15 09:46:47 +01:00
Daniel Agar f8eaa6e46b ROMFS handle bl_update generically 
- include all available legacy bootloaders
 2021-03-11 00:38:18 +01:00
Daniel Agar 4d288512b5 add board architecture specific init defaults 2021-03-09 19:59:41 +01:00
David Sidrane d94ff14e6b px4_fmu-v5x:Use Auto LSE Drive setting 2021-03-05 15:40:09 -05:00
Daniel Agar 19de1e57e3 gyro_fft promote to modules and include on all boards 2021-03-05 10:56:54 -05:00
garfieldG 3cd9b3c2cf Added support in Mavlink Ethernet channel parameters 
Mavlink Ethernet channel settings such as udp port, remote port and broadcast mode now can be changed dynamically via parameters.
 2021-02-25 08:52:38 -08:00
Beat Küng 7e33d03470 drivers: remove tap_esc 
- it's not used anymore
- it would need a refactoring to use mixer_module
 2021-02-25 09:28:37 -05:00
Daniel Agar 414f9f81d9
move fake GPS to standalone module 2021-02-20 14:13:36 -05:00
Daniel Agar ab0d0fd0be
uORB move to PX4 platform layer 2021-02-17 11:25:56 -05:00
Daniel Agar 44df0fb7a2 Analog Devices ADIS16448 rewrite 
- new IMU driver structure with state machine (no sleeps in bus thread)
 - verify all configured registers and trigger reset on failure
 - detect if DIO1 or DIO2 are actually connected for data ready interrupt usage
 - don't use CRC-16 on burst transfers except for verified lots
 2021-02-16 10:29:07 +01:00
Lorenz Meier 4c9b2c65b5 Support v5X build variants 
This adds support for the different implementation variants of the v5X standard.
 2021-02-14 11:17:28 +01:00
Daniel Agar fb2a199621 delete unmaintaned mkblctrl driver 2021-02-14 10:38:15 +01:00
Daniel Agar a257120e8d boards: use new param default mechanism 2021-02-12 08:27:47 -05:00
Lorenz Meier 80b8e6a48f v5X: Register board variants 
This is needed to properly identify new variants.
 2021-02-11 22:14:02 +01:00
Daniel Agar 8f0918a16b boards: remove unused linker __param section 2021-02-08 23:22:48 -05:00
Lorenz Meier d03d46b8a3 Initialize MAVLink on v5X variants 
This will ensure that the different baseboard configurations are properly accounted for depending on HW variants.
 2021-02-07 17:23:13 +01:00
dino bb37fd2f29 Enabled LSE clock for RTC, set clk drive strength to 3. Else the quarzt on the fmuv5x does not socillate reliabel. 2021-02-02 09:58:47 +01:00
Daniel Agar a2442ffb48 board: enable UAVCAN sensors by default on F7/H7 2021-02-02 09:01:12 +01:00
David Sidrane d22eb76187 Add a simple network manager 
This system command will display, set and save the network
   settings.

   netman show   - Displays the current settings.

   netman update - Will check for a net.cfg file on the SD card.
                   If present, it will update the paramaters,
                   delete the file, and reboot. Using the new settings.

   netman save - Saves the current settings to net.cfg on the SD card.
                 This file shoulf be renamed to preserver it across
                 reboots or editited to chech networkin paramates.

   File format is name<space>value:

   echo DEVICE=eth0           > /fs/microsd/net.cfg
   echo BOOTPROTO=fallback    >> /fs/microsd/net.cfg
   echo IPADDR=192.168.0.4    >> /fs/microsd/net.cfg
   echo NETMASK=255.255.255.0 >>/fs/microsd/net.cfg
   echo ROUTER=192.168.0.254  >>/fs/microsd/net.cfg
   echo DNS=192.168.0.254     >>/fs/microsd/net.cfg

   Valid values for `proto` are `dhcp`, `static`, `falback`
   Both will try dhcp for CONFIG_NETINIT_FALLBACK times
   and fall back to the static address.

   NETMASK - is the network mask.
   IPADDR  - this nodes ip address for static or fall back.
   ROUTER  - The default route.
   DNS     - The address of the dns server.
 2021-01-31 14:42:09 +01:00
David Sidrane ed996e2dd1 fmu-v5x:Add net monitoring an DHCP 
px4_fmu-v5x:Use Bin Net settigns
 2021-01-31 14:42:09 +01:00
Daniel Agar 1ec10bfcc6
boards: disable CONFIG_ARMV7M_LAZYFPU again (#16573) 
- this was causing hard faults on the CUAV Nora and possibly other boards, disabling everywhere until we fully understand the root cause
 2021-01-17 22:40:21 -05:00
Beat Küng e2337a34eb system_power: add comp_5v_valid and can1_gps1_5v_valid 
And fill it in from the v5x GPIO expander.
 2021-01-15 10:57:20 -05:00
Beat Küng 88fe047556 px4/v5x: enable mcp23009 GPIO driver 2021-01-15 10:57:20 -05:00
Beat Küng 26e8c231b0 v5x,v6x: move mtd_caldata after mtd_id partition 
to avoid losing factory calibration params on existing setups
 2021-01-15 10:57:20 -05:00
Beat Küng 9f5dee2ecf v5x/v6x: update IMU sensors (remove ISM330DLC) 2021-01-12 09:55:59 -05:00
Daniel Agar cb74cb8692 boards: enable CONFIG_ARMV7M_LAZYFPU everywhere 2021-01-12 09:04:38 +01:00
Daniel Agar 763c3b8fda boards: start enabling multi-EKF by default on F7/H7 2021-01-10 17:56:34 +01:00
Matthias Grob 7545249215 Add flight_mode_manager to all targets with mc_pos_control 2020-12-30 10:25:08 -05:00
David Sidrane 22bc176885 Added mft for queries 2020-12-02 20:40:23 -05:00
David Sidrane a60df85a09 px4_fmu-v5x:Use px4_platform_configure 2020-12-02 20:40:23 -05:00