- publish wind estimate only from EKF, and wind speeds from airspeed selector to new separate topic (airspeed_wind)
- rename message wind_estimate to wind
- publish wind from currently used ekf instance (ekf2selector)
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
We should be using gimbal_manager_information and not
gimbal_device_information. Plus, this updates the fields and flags
according to the MAVLink changes.
- add command to request a message
- add gimbal attitude message
mavlink_receiver handle GIMBAL_MANAGER_SET_ATTITUDE
first implementation of new vmount input MavlinkGimbalV2
- setup class
- decode gimbal_manager_set_attitude in ControlData
add gimbal information message
add gimbal manager information and vehicle command ack
mavlink messages: add stream for GIMBAL_MANAGER_INFORMATION
mavlink_receiver: handle GIMBAL_DEVICE_INFORMATION
remove mavlink cmd handling from vmount input MavlinkGimbalV2
complete gimbal manager:
- send out fake gimbal_device_information for dummy gimbals
- complete ROI handling with nudging
small fixes
fix typos
cleanup
- gimbal device information
- flags lock
- check sanity of string
add support for CMD_DO_GIMBAL_MANAGER_ATTITUDE
stream GimbalDeviceAttitudeStatus for dummy gimbals
- add uROB gimbal_attitude_status
- fill status in vmount output_rc for dummy gimbals not able to send the
status themselves
- stream mavlink GimbalDeviceAttitudeStatus
better handle the request for gimbal infomation request
clean up
bring gimbal information back on vmount init
add new gimbal message to mavlink normal stream
fix publication of gimbal device information
rename gimbal_attitude_status to gimbal_device_attitude_status
stream gimbal_manager_status at 5Hz
mavlink: send information only on request
Sending the information message once on request should now work and we
don't need to keep publishing it.
mavlink: debug output for now
make sure to copy over control data
mavlink: add missing copyright header, pragma once
mavlink: address review comments
mavlink: handle stream not updated
Our answer does not just depend on whether the stream was found but
whether we actually were able to send out an update.
mavlink: remove outdated comment
vmount: add option for yaw stabilization only
The stabilize flag is used for gimbals which do not have an internal IMU
and need the autopilot's attitude in order to do stabilization. These
gimbals are probably quite rare by now but it makes sense to keep the
functionality given it can e.g. be used by simple servo gimbals for
sensors other than highres cameras.
The stabilize flag can also be re-used for gimbals which are capable of
stabilizing pitch and roll but not absolute yaw (e.g. locked to North).
For such gimbals we can now set the param MNT_DO_STAB to 2.
We still support configuring which axes are stabilized by the
MAVLink command DO_MOUNT_CONFIGURE, however, this is generally not
recommended anymore.
vmount: fix incorrect check for bit flag
mavlink_messages: remove debug message
Signed-off-by: Claudio Micheli <claudio@auterion.com>
use device id
remove debug print
gimbal attitude fix mistake
clang tidy fix
split:
- gimbal_attitude -> gimbal_device_set_attitude, gimbal_manager_set_attitude
- gimbal_information -> gimbal_device_informatio, gimbal_manager_information
add gimbal protocol messages to rtps msg ids
support set attitude for gimbal directly speaking mavlink
clean up gimbal urob messages
vmount: address a few small review comments
vmount: split output into v1 and v2 protocol
This way we can continue to support the MAVLink v1 protocol. Also, we
don't send the old vehicle commands when actually using the new v2
protocol.
vmount: config via ctor instead of duplicate param
vmount: use loop to poll all topics
Otherwise we might give up too soon and miss some data, or run too fast
based on commands that have nothing to do with the gimbal.
typhoon_h480: use gimbal v2 protocol, use yaw stab
Let's by default use the v2 protocol with typhoon_h480 and enable yaw
lock mode by stabilizing yaw.
- new heater_status logging message
- run continously at low rate until configured sensor is found
- fix px4io fd bugs (fd open/close/ioctl must be same thread)
Instead of directly doing the link loss reaction which by default is RTL a delay
can be configured such that the drone first switches to hold and waits
for the link to be regained.
For some usecases like starting video recording on a companion computer or triggering a ROS based (offboard control) mission control execution the status of RC channel is needed in ROS(2). This allows the user to start/stop such functionalities from the RC transmitter.
Therefore InputRc to be changed accordingly.
add 'Set send: true' for id: 30
Add new DeviceBusType_SERIAL to Device::DeviceId union
Add DRV_DIST_DEVTYPE's for all distance sensors
Change distance_sensor_s.id to distance_sensor_s.device_id
Modify all distance_sensor drivers to apply 'proper' device_id
- control allocation module with multirotor, VTOL standard, and tiltrotor support
- angular_velocity_controller
- See https://github.com/PX4/PX4-Autopilot/pull/13351 for details
Co-authored-by: Silvan Fuhrer <silvan@auterion.com>
Co-authored-by: Roman Bapst <bapstroman@gmail.com>
- commander preflightcheck use estimator_sensor_bias message instead of EKF state index magic number
- ekf2 publish estimated bias limits in estimator_sensor_bias
- preflightcheck only error if bias estimate exceeds half of configured limit (delete COM_ARM_EKF_AB and COM_ARM_EKF_GB parameters)
- handle saving the mag bias per sensor (across all estimator instances using that mag) in sensors/vehicle_magnetometer
- this is now saving back to the actual mag calibration CAL_MAGn_OFF{X,Y,Z}
- ekf2 reset mag mag bias on any magnetometer or calibration change
- use Kalman filter scheme to update stored mag bias parameters using all available bias estimates for that sensor
Co-authored-by: Paul Riseborough <gncsolns@gmail.com>
Silvan Fuhrer
jciberlin
Daniel Agar
Julian Oes
Julian Kent
Martina Rivizzigno
Ildar Sadykov
Matthias Grob
Antonio Sanjurjo Cortés
Gerald
TSC21
Claudio Micheli
JacobCrabill
David Sidrane
TheLegendaryJedi
Mathieu Bresciani
Beat Küng
Julien Lecoeur
RomanBapst