- drivers/tone_alarm: move to ModuleBase and purge CDev (/dev/tone_alarm0)
- drivers/tone_alarm: only run on tune_control publication (or scheduled note) rather than continuously
- drivers/tone_alarm: use HRT to schedule tone stop (prevents potential disruption)
- msg/tune_control: add tune_id numbering
- systemcmds/tune_control: add "error" special case tune_id
- move all tune_control publication to new uORB::PublicationQueued<>
- start tone_alarm immediately after board defaults are loaded to fix potential startup issues
- for SITL (or other boards with no TONE output) print common messages (startup, error, etc)
UART is the primary interface for telemetry radio: https://docs.emlid.com/navio2/ardupilot/hardware-setup/#uart-radio
Check first if /dev/ttyUSB0 exists (https://docs.emlid.com/navio2/ardupilot/hardware-setup/#usb-radio); if not, fall back to configuring over UART (/dev/ttyAMA0).
Use stricter check for character special file (-c) rather than just file (-f).
'console=serial0,115200' needs to be removed from /cmdline.txt as additional configuration step. This should be documented in the Navio2 section of docs.px4.io. Presumably, this is already performed as part of the Raspberry Pi OS prebuilt image Emlid spins.
I observed stack overflows when executing `uavcan params list`, so the
stack size probably needs to be increased.
Signed-off-by: Alex Mikhalev <alexmikhalevalex@gmail.com>
Sometimes, the mission_result timestamp is the same as the
internal_state timestamp which would meant that we would not switch to
LOITER even though the takeoff is clearly done at that point.
Track Changes in NuttX stm32h7 flash driver:
The STM32H7 flash driver uses up_progmem_pagesize to
describe minimum write size to satify the block size
requierment for ECC.
Therefore, the image size needs to be padded to a multiple
of up_progmem_pagesize()
sensors having mixer_module creates a dependency on sensors for
the param MOT_SLEW_MAX. Things that do not uses sensors.
IE. PWM only device should not have to include them.
- ecl in PX4/Firmware (2b34fec0844646d13a57f78dbbed44b53813919e): 6b99ea2a60
- ecl current upstream: 4c2355a638
- Changes: 6b99ea2a60...4c2355a6384c2355a 2020-09-25 Daniel Agar - EKF: use GPS to lookup declination from WMM before full GPS checks pass
Motors in Px4 ecosystem are indexed using 1-based indexing (Airframe reference, dshot command, etc.) motor_test command is 0-based. This PR changes motor_test to use 1-based indexing.
This PR refers to Github issue #15721.
* Added buffer length check to SMBus::block_read (triggered hardfault in batt_smbus module by writing beyond buffer end due to device returning longer byte_count than requested/expected)
Co-authored-by: Florian Olbrich <florian.olbrich@scarabot.de>
Co-authored-by: Daniel Agar <daniel@agar.ca>
Co-authored-by: BazookaJoe1900 <BazookaJoe1900@gmail.com>
Co-authored-by: Beat Küng <beat-kueng@gmx.net>
- new sensors work item that subscribes to N x sensor_gps and publishes vehicle_gps_position
- blending is now configurable with SENS_GPS_MASK and SENS_GPS_TAU
Co-authored-by: Jacob Crabill <jacob@volans-i.com>
Co-authored-by: Jacob Dahl <dahl.jakejacob@gmail.com>
Daniel Agar
jaeyoung
blazczak
Beat Küng
Alex Mikhalev
SalimTerryLi
Nicolas MARTIN
CarlOlsson
Julian Oes
David Sidrane
Nicolas Martin
PX4 BuildBot
justas-
flochir
Tanja Baumann
Jacob Dahl