Transitions in Stabilized mode are done manually, the pilot controls the pitch angle
and if it's above the threshold the transition is declared finished (plus airspeed
check for front transition). Thus we can't have fixed thresholds but need to link
them to the actual max pitch angle in Stabilized mode.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
We currently fuse 0 as airspeed rate measurement, and thus simply low-pass
filter the airspeed measurements. Testing has shown that the current default
on the airspeed rate measurement noise is set to low, and thus the airspeed
mesurement is filtered too much.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
A VTOL plane in MC mode has no yaw setpoint during takeoff because of
weather-vane. To align for the front transition, the yaw target jumps
and caused a step in the controller, making it reach saturation.
With this commit, the previous yaw setpoint is set to the current yaw
when no yaw setpoint is sent in order to create a smooth yaw trajectory
starting at the current orientation when yaw target is suddenly finite.
The yawspeed filter also now contains the yaw speed instead of dyaw in
order to prevent chattering due to dt jitter.
The API is cleaner if the control_data is const reference and the device
compid is an explicit output argument.
Signed-off-by: Julian Oes <julian@oes.ch>
The resets in the modes (eg Loiter mode) are not active yet, so manually
set rep->current.cruising_speed = -1.f if not already in the same flight mode.
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
When flow control is used together with DMA, we need to add a pulldown
to CTS. Without it, it assumes flow control and gets stuck when
CTS is not connected.
Signed-off-by: Julian Oes <julian@oes.ch>
When we fall back to another link, we are already doing a uORB copy when
checking the data. Therefore, we should further down use/send that data
instead of overwriting it immediately.
Signed-off-by: Julian Oes <julian@oes.ch>
I don't think it makes sense to slow down switching RTCM injection to
once every 5 seconds. If we don't have corrections, we should check and
use whatever we get as soon as possible.
Signed-off-by: Julian Oes <julian@oes.ch>
We need to reset the instance after looping through all instances.
Otherwise, we are left with the last instance if none is valid but have
not updated the _selected_rtcm_instance which is what is logged.
Therefore, this change fixes the logged RTCM instance.
Signed-off-by: Julian Oes <julian@oes.ch>
- sitl_gazebo-classic in PX4/Firmware (4bb4bc185b): 1c5818e56c
- sitl_gazebo-classic current upstream: 3f2b9678af
- Changes: 1c5818e56c...3f2b9678af
3f2b967 2023-04-11 JaeyoungLim - Ignore sdf validation for land_pad (#977)
a91e4fd 2023-04-11 Jonas Perolini - Add support for camera and new land pad in irlock simulation (#950)
8fcd3cf 2023-04-10 JaeyoungLim - Remove bionic related tests (#974)
It turns out that I had omitted implementing the gimbal_device_id which
is the component ID of the gimbal device that the gimbal manager (in
this case PX4) is responsible for.
Signed-off-by: Julian Oes <julian@oes.ch>
bresch
Silvan Fuhrer
Alejandro Hernández Cordero
JaeyoungLim
Daniel Agar
Morten Fyhn Amundsen
Thomas Debrunner
PX4 BuildBot
Julian Oes
muramura
alexklimaj
Beniamino Pozzan
David Sidrane
SalimTerryLi