| .. |
|
APM_Config.h
|
Plane: removed HIL_MODE_ATTITUDE
|
2013-04-12 17:44:40 +10:00 |
|
APM_Config.h.reference
|
Plane: updates for new compass API
|
2013-05-02 12:48:14 +10:00 |
|
ArduPlane.pde
|
Plane: update_mount assumes 50Hz, for camera trigger
|
2013-06-25 12:44:26 +10:00 |
|
Attitude.pde
|
Plane: APM2 doesn't have channel 9 PWM output
|
2013-06-24 13:06:54 +10:00 |
|
GCS.h
|
Plane: switch to an array for stream rates
|
2013-02-05 08:20:41 +11:00 |
|
GCS_Mavlink.pde
|
Plane: switch to new AP_Scheduler
|
2013-06-04 13:34:58 +10:00 |
|
Log.pde
|
Plane: switch to new AP_Scheduler
|
2013-06-04 13:34:58 +10:00 |
|
Makefile
|
Plane: use new apm.mk
|
2013-01-02 17:28:21 +11:00 |
|
Parameters.h
|
Plane: enabled RELAY_* parameters
|
2013-06-25 12:44:26 +10:00 |
|
Parameters.pde
|
Plane: enabled RELAY_* parameters
|
2013-06-25 12:44:26 +10:00 |
|
climb_rate.pde
|
uncrustify ArduPlane/climb_rate.pde
|
2012-08-21 18:57:21 -07:00 |
|
command_description.txt
|
Cleanup: rename files with spaces in their names, replace with underscores
|
2012-02-28 16:14:31 -08:00 |
|
commands.pde
|
Plane: set loiter.direction for GUIDED mode
|
2013-04-21 23:46:35 +10:00 |
|
commands_logic.pde
|
Plane: use RC_Channel::rc_channel() instead of rc_ch[]
|
2013-06-03 16:23:48 +10:00 |
|
commands_process.pde
|
Plane: switch to new AP_Scheduler
|
2013-06-04 13:34:58 +10:00 |
|
compat.h
|
ArduPlane: Ported to AP_HAL
|
2012-12-20 14:51:36 +11:00 |
|
compat.pde
|
ArduPlane: Ported to AP_HAL
|
2012-12-20 14:51:36 +11:00 |
|
config.h
|
Plane: use the new airspeed driver interface
|
2013-06-03 11:51:09 +10:00 |
|
control_modes.pde
|
Plane: ignore control mode changes when in throttle failsafe
|
2013-02-21 11:21:39 +11:00 |
|
createTags
|
imported ArduPlane from ArduPilotMega svn
|
2011-09-09 11:29:39 +10:00 |
|
defines.h
|
Plane: fixed remaining places where primary channel ordering was assumed
|
2013-06-03 16:23:48 +10:00 |
|
events.pde
|
Plane: make voltage and battery capacity failsafe settable at runtime
|
2013-05-22 20:33:57 +10:00 |
|
failsafe.pde
|
Plane: fixed remaining places where primary channel ordering was assumed
|
2013-06-03 16:23:48 +10:00 |
|
geofence.pde
|
Plane: use hal.storage for eeprom access
|
2012-12-20 14:51:39 +11:00 |
|
navigation.pde
|
Plane: switch to new AP_Scheduler
|
2013-06-04 13:34:58 +10:00 |
|
nocore.inoflag
|
ArduPlane: Ported to AP_HAL
|
2012-12-20 14:51:36 +11:00 |
|
radio.pde
|
Plane: APM2 doesn't have channel 9 PWM output
|
2013-06-24 13:06:54 +10:00 |
|
sensors.pde
|
Plane: switch to new AP_Scheduler
|
2013-06-04 13:34:58 +10:00 |
|
setup.pde
|
Plane: allow channel mapping of first 4 channels
|
2013-06-03 16:23:48 +10:00 |
|
system.pde
|
Plane: make GPS UART blocking again
|
2013-06-11 18:50:23 +10:00 |
|
test.pde
|
Plane: switch to new AP_Scheduler
|
2013-06-04 13:34:58 +10:00 |
0d3faeda90