0607be8ea5
ArduCopter - removed unused motor pde files including heli.pde, motors_hexa.pde, motors_octa.pde, motors_octa_quad.pde, motors_tri.pde and motors_y6.pde
2012-04-04 23:06:12 +09:00
2128085576
ArduCopter - test.pde - changed references "motor_armed" to "motors.armed()" as part of move to AP_Motors library.
...
Change to ESC initialisation calls to use motors.throttle_pass_through method of AP_Motors class.
2012-04-04 23:05:26 +09:00
2fc3b740c4
ArduCopter - system.pde - changed references to "motor_armed" to "motors.armed()" as part of the move to use AP_Motors library.
2012-04-04 23:03:21 +09:00
5e2147de1f
ArduCopter - setup.pde - changed cli for helicopter to call the new AP_Motors class's parameters instead of the global parameters.
...
changed init_esc to call the AP_Motor's class's "throttle_pass_through" function.
2012-04-04 23:02:29 +09:00
1701cac0b1
ArduCopter - radio.pde - changed motor initialisation to set update rate, frame orientation, min and max throttle to AP_Motors class.
...
Note: perhaps the motors speed at least should be moved to a parameter within the motors class.
output_min function greatly simplified as this is handled by the AP_Motors class.
2012-04-04 23:00:56 +09:00
0f4203a755
ArduCopter - motors.pde - changed references to "motor_armed" to "motors.armed()" because we've moved to using the AP_Motors class.
...
Simplified set_servos_4 function which was responsible for calling "output_motors_armed" or "output_motors_disarmed" as this determination as to whether the motors are armed or not is handled within the AP_Motors class.
2012-04-04 22:58:42 +09:00
00d540bfa9
ArduCopter - leds.pde - changed refrences to "motor_armed" to "motors.armed()"
2012-04-04 22:57:50 +09:00
ffd77f58ab
ArduCopter - removed references to MOT_1 etc as these are now within the AP_Motors class (i.e. MOT_1 has become AP_MOTORS_MOT_1)
2012-04-04 22:56:07 +09:00
929e933b69
ArduCopter - increased firmware version to 118. Removed nearly all heli parameters as these are all created by the AP_MotorHeli class now.
...
Note: we cannot move the heli_servos to the AP_MotorHeli class yet because of a small issue in the parameters class.
2012-04-04 22:55:07 +09:00
acc24291f3
ArduCopter - Log.pde - changed MOT output to dataflash to take values from AP_Motors class's motor_out array instead of the global motor_out array.
2012-04-04 22:53:21 +09:00
86d2a9ffdb
ArduCopter - GCS_Mavlink.pde - changed output to ground station to use new AP_Motor's class motors array inplace of the global "motor_out" array.
2012-04-04 22:52:26 +09:00
23c3f25654
ArduCopter - Attitude.pde - moved heli_get_angle_boost from heli.pde (which will be removed) to Attitude.pde. In fact we should combine heli_get_angle_boost and the regular get_angle_boost.
2012-04-04 22:51:39 +09:00
544237d60a
ArduCopter - add includes for new AP_Motors classes.
...
Remove global motor_filtered and motor_out arrays.
Removed all global heli variables.
replace "motor_armed" with "motors.armed()"
removed output to rc_4 for tri because this is now handled by AP_MotorsTri class
2012-04-04 22:50:43 +09:00
eecadef7dc
APM Planner 1.1.60
...
add stab kd ch6
fix mono/linux serial port list
2012-04-04 06:58:45 +08:00
1450c3f5af
autotest: fixed overshoot due to low resolution log timing
2012-04-03 10:43:05 +10:00
2e11584fb7
autotest: fixed order of startup messages
2012-04-03 09:53:26 +10:00
07f44263ad
Merge branch 'master' of https://code.google.com/p/ardupilot-mega
2012-04-02 12:45:20 -07:00
71ad185238
ArduCopter - AP_Motors library - added new library which has few advantages over current code:
...
1. it's step towards rearchitecting the current code base ahead of a move to RTOS.
2. internally it uses a MatrixTable for the Quad, Octa, OctaQuad, Y6 frames.
3. it implements the missing stability patch for Octa and OctaQuads (still missing for Y6)
Later check-ins will incorporate into the main ArduCopter code.
2012-04-02 17:26:37 +09:00
40d7b07789
MAVLink: port the new adaptive flow control to ArduCopter
...
This allows for arbitrary stream rates, and supports flow control if
you are using a 3DR radio
2012-04-02 11:18:53 +10:00
b38d8c526f
MAVLink: make parameter send use adaptive stream rate
...
this makes it possible to fetch parameters with very low air data
rates
2012-04-02 11:18:53 +10:00
5ce5f3d176
MAVLink: import change to txbuf as a percentage
2012-04-02 11:18:53 +10:00
222009002e
MAVLink: allow for find grained stream rate control
...
streams can now be requested at any multiple of 20ms. So if you ask
for a stream at 7Hz then you will get it at close to 7Hz.
2012-04-02 11:18:53 +10:00
0d19678638
Merge branch 'master' of https://code.google.com/p/ardupilot-mega
2012-04-01 16:23:42 -07:00
8a215c8b55
MAVLink: imported new headers, with RADIO packet
2012-04-01 21:44:44 +10:00
b0c9a25024
ArduCopter - CH6 tuning - changed Roll/Pitch Rate D tuning to use the user supplied tuning range instead of the range / 100.
...
also changed heli_ext_gyro_gain to make it use the tuning range directly.
2012-03-31 09:28:25 +09:00
1e0a2fb0be
MAVLink: don't waste 100 bytes of bandwidth sending 1 byte of information
...
the GPS_STATUS message is a massive waste of bandwidth, but it is the
only message that tells us the number of visible satellites. So only
send it if that information changes.
This makes MAVLink work better at low baud rates
2012-03-30 17:46:20 +11:00
e9773ea09c
APM: use set_blocking_writes(false) when we have done ground start
2012-03-30 17:46:20 +11:00
0985327331
ACM: use set_blocking_writes(false) when we arm motors
2012-03-30 17:46:20 +11:00
08b66e18b7
FastSerial: added set_blocking_writes() interface
...
this allows us to put a serial port into non-blocking mode, so that
writes that don't fit in the transmit buffer are dropped. This will be
used in flight to prevent stray printf() calls from causing large time
delays in the code
2012-03-30 17:46:20 +11:00
36e741b078
MAVLink: raise the serial transmit buffer size to 256 bytes
...
the 128 byte serial transmit buffer was causing significant problems
with queueing of mavlink messages. With 256 bytes we can fit a lot
more messages out in each pass of the code, which makes telemetry more
efficient
As we discussed on the dev call, we now have enough free ram for this
to be worthwhile
2012-03-30 17:46:20 +11:00
c221c91f87
autotest: use the automatic declination code in autotest
2012-03-30 14:25:27 +11:00
c2ff66c9cd
examples: fixed build of some examples with new AP_Declination code
2012-03-30 14:25:27 +11:00
5dbd2a2b60
APM: enable AP_Declination by default
2012-03-30 14:25:27 +11:00
58f539ca35
ACM: removed FORCE_AUTOMATIC_DECLINATION_UPDATE
...
we now have the EEPROM option COMPASS_AUTODEC instead
2012-03-30 14:25:27 +11:00
825340d53d
Compass: added COMPASS_AUTODEC option
...
when this is 1 (which is the default), we will get the declination
automatically via the AP_Declination library
when it is 0 we will use the value configured by the user
2012-03-30 14:25:27 +11:00
a98a092a59
AP_Declination: enabled auto declination by default in APM
2012-03-30 14:25:27 +11:00
e4e052ff91
AP_Declination: save some more memory by putting the declination keys in progmem
...
there was a comment saying this was too slow, but it actually costs
about 30 usec extra, which is trivial given the full auto declination
call costs 680 usec and its only called once per boot
2012-03-30 14:25:27 +11:00
edb627a5c1
AP_Declination: added timing information to declination test
2012-03-30 14:25:27 +11:00
01c4cde14f
AP_Declination: fixed build under SITL
2012-03-30 14:25:27 +11:00
9c414e9573
AP_Declination_test: Updated test with better print messages.
2012-03-30 14:25:26 +11:00
cff189e911
AP_Declination: Update LUT based on the changes that I made in the LUT generation code. This LUT is the final version that has no truncation.
2012-03-30 14:25:26 +11:00
0727955fe3
ArduCopter: Changed implementation of configuration value for automatic declination. There is now a FORCE_AUTOMATIC_DECLINATION_UPDATE that when enabled will update the declination on every GPS 3D fix regardless of whether or not the user saved a value to the EEPROM. By default the declination will only be set by the automatic declination routine if the user has not saved a declination to the EEPROM.
2012-03-30 14:25:06 +11:00
380b9ece44
AP_Declination: Updated comments to reflect new LUT size.
2012-03-30 14:25:06 +11:00
c04e074c89
AP_Declination: Removed trailing zero deltas as they have no impact on the final value and only take up extra bytes.
2012-03-30 14:21:58 +11:00
662f11f801
AP_Declination: Updated compressed lookup value table. Located 9 more failure points due to truncation on the packed LUT.
2012-03-30 14:21:58 +11:00
0178906389
AP_Declination: Found 7 of the 22 failure points and fixed them. The issue with those 7 was the way I originally packed the value array. The last delta values on some rows were getting truncated. The new number of failures is down to 15 - WIP.
2012-03-30 14:21:58 +11:00
08259bb2de
AP_Declination: Updated test to run in 5 degree increments. Changed to only print failures and also print total pass vs total fail.
2012-03-30 14:21:58 +11:00
64c236800c
AP_Declination: Moved check for y index of zero to after the y index is properly transformed.
2012-03-30 14:21:58 +11:00
e99d26cfa3
AP_Declination: The exception signs unpacking logic was incorrect. I was shifting a 1 value left y%8 which would have needed a the signs to be packed right to left. My packed signs byte was packed left to right (left most being the 0 position) so I needed to reverse the shifting.
2012-03-30 14:21:58 +11:00
d9c9e0e608
AP_Declination: In order for the bitwise & operation to work, negative signs need to be represented by 1s instead of 0s. Changed so that negative signs are represented by a 1 in the packed signs array. Updated lookup logic to reflect this change.
2012-03-30 14:21:58 +11:00
rmackay9
Michael Oborne
Andrew Tridgell
Chris Anderson
Adam M Rivera