68ae91a729
APM: added AMP_OFFSET option
...
thanks to Alexey Kozin!
2012-11-21 13:34:27 +11:00
9e3ae301b1
ArduPlane: move to use new INS library instead of IMU library
2012-11-07 19:21:03 +09:00
efc2324666
APM: added RSSI_PIN option for receiver RSSI
...
this allows you to configure the pin for receiver RSSI without
recompiling
2012-11-06 22:04:41 +11:00
e151d3735a
ArduPlane: added BATT_VOLT_PIN and BATT_CURR_PIN parameters to allow support for new 3DR IV battery monitor
2012-10-13 20:51:41 +09:00
4bca609b9f
AP_InertialSensor_MPU6000: replaced _cs_pin parameter with #define and saved 1 byte of memory
...
Updated ArduCopter, ArduPlane and example sketches in AP_InertialSensor, AP_IMU and AP_AHRS libraries because they no longer need to pass in cs_pin to the constructor
2012-09-28 19:21:59 +09:00
41a4490c5a
APM: tweak the default options for an APM1 1280 board
...
this allows a few more things to fit in
2012-09-19 19:36:19 +10:00
7d84666b9d
APM: removed the unused sonar code
...
when we start supporting a sonar we'll add a AP_Sonar library, like
AP_Airspeed
2012-09-19 19:35:22 +10:00
77926a6965
APM: switch to Randys new IMU rate control method
...
this drives the speed of the 50Hz loop by the number of samples
accumulated in the IMU. This should give much more consistent timing
in DCM.
Thanks to Randy for introducing this scheme in ArduCopter!
2012-09-11 16:39:36 +10:00
88f4a3bc4a
APM: allow serial buffer size to be configured
...
very useful for packet forwarding setups
2012-09-08 10:06:35 +10:00
332ad921cc
APM: added new TELEM_DELAY parameter
...
number of seconds to delay telemetry
2012-08-30 08:59:39 +10:00
3403e1b78d
Arducopter: increased MAVLINK delay to 6s to reduce the chance of xBee bricking
...
Arduplane: increased MAVLINK delay to 6s to reduce the chance of xBee bricking
Ardurover: increased MAVLINK delay to 6s to reduce the chance of xBee bricking
2012-08-28 20:09:10 -07:00
90aa5f2004
ArduPlane: Fix 1280 builds
...
Added fine-granular features in the AP_Mount class to reduce code size on 1280 chips
Remove camera trigger support on 1280 chips
2012-08-27 01:33:45 +02:00
25916e9a92
Improve comments, no functional changes
2012-08-27 01:32:27 +02:00
e74dab122a
APM: added RECEIVER_RSSI_PIN option
...
this allows for the receiver RSSI to be sent over MAVLink
Thanks to Burt Green for the suggestion
2012-08-22 13:33:12 +10:00
2bc2460c07
APM: optional build with new controller libs
2012-08-22 12:39:07 +10:00
e4badcccab
uncrustify ArduPlane/config.h
2012-08-21 19:19:51 -07:00
5d29d5e5a1
APM: removed DMP support from ArduPlane
...
Without centripetal correction the DMP code will almost certainly
crash a plane
2012-08-22 11:46:35 +10:00
bd6581c523
AHRS: removed Quaternion build support from APM/ACM/rover
2012-08-22 10:42:21 +10:00
93f45f232f
APM: added 'OBC' failsafe module for ArduPlane
...
this adds FS_* parameters for setting up APM to follow the outback
challenge failsafe rules.
This includes:
- manual pin
- heartbeat pin
- waypoint for heartbeat failure
- waypoint for GPS failure
2012-08-15 12:39:34 +10:00
54f97bb9e7
APM: removed THROTTLE_REVERSE option
...
Better to use RC3_REV
2012-08-09 10:04:44 +10:00
6e46db39a1
APM: Added STICK_MIXING option
...
this replaces the compile time option. Disabling during long distance
flights when the transmitter may be out of range is useful.
2012-08-09 08:53:29 +10:00
9a8fd4738e
Add an optional second mount to ArduPlane and ArduCopter
2012-08-08 23:22:24 +02:00
5e19c0cf04
AP_Airspeed: removed values passed to constructor
2012-08-08 16:38:39 +10:00
7d9e4a7559
APM: fixed default flap speed
...
the default of 255 translates to -1 as a AP_Int8, so use zero to mean
no flaps
2012-08-08 13:04:21 +10:00
b366205172
APM: removed cli slider and dipswitch options
...
use mavlink/eeprom for all config
2012-08-08 12:12:29 +10:00
813e3ad229
Enable camera triggering by default
2012-08-04 16:32:47 +02:00
8f836b2fd6
ATmega1280 does not have enough memory for mount support so disable AUTO GPS support, to allow mount support to fit.
...
This should almost have no side effects, because the most users use MTK anyways.
If the user defined a GPS protocol, than we will NOT overwrite it
2012-08-04 16:32:20 +02:00
717d0d25d4
ArduPlane: allow MPU6000's DMP to be used for attitude estimation.
...
Enable by adding this line to APM_Config.h:
#define DMP_ENABLED ENABLED
2012-07-28 19:50:40 +09:00
6243cf77a8
APM: added a SCALING_SPEED parameter
...
this allows users to adjust the base speed used for scaling roll/pitch
PIDs. This can be used to make PIDs work for both airspeed and
non-airspeed control
2012-07-26 11:30:23 +10:00
7bc724d118
APM: changed PID library to do automatic deltat calculation
...
this fixes a problem with the HDNG2RLL PID, which was using the wrong
time base and prevents similar bugs from happening in the future
2012-07-06 19:59:18 +10:00
fe54329de2
MAVLink: remove MAVLink 0.9 protocol support
...
this simplifies the code a lot. We're not going back to 1.0
2012-07-05 13:00:46 +10:00
2cebd44313
With CLI and MOUNT active, the linker says: region `text' overflowed by 3858 bytes
...
So disable CLI when MOUNT is active. Sorry I did not detect it before, but the APM_Camera branch worked in a different way.
2012-06-13 21:08:09 +02:00
a12cb8fd9a
Added camera trigger functionality
2012-06-13 21:00:20 +02:00
1eb2d0e485
Added missing Manual_level config
2012-06-10 13:08:48 -07:00
7d2532450a
enable mavlink10 by default
2012-06-04 08:02:08 +08:00
78d273fa34
Telemetry: make it possible to use UART2 on APM2
...
building with TELEMETRY_UART2=ENABLED allows you to use the solder
bridge on the APM2 to enable telemetry on UART2. This allows both USB
telemetry and a radio at the same time.
2012-05-04 10:39:44 +10:00
1017b0f6a3
APM-nav: set NAV I value defaults to 0.1
...
a small I value is good on most planes, so I think this is a better
default than 0. Thanks to Chris for asking about this.
2012-04-30 12:27:30 +10:00
0a38e2b8d4
Updated ArduPlane/ArduCopter cmake options.
2012-04-18 15:16:02 -04:00
5dbd2a2b60
APM: enable AP_Declination by default
2012-03-30 14:25:27 +11:00
a98a092a59
AP_Declination: enabled auto declination by default in APM
2012-03-30 14:25:27 +11:00
a203282779
correct small typos in comments
2012-03-11 21:30:09 +01:00
566bbed7ad
AP_Declination: Added new config value to allow the user to have the declination overwritten on every 3D fix.
...
Signed-off-by: Andrew Tridgell <tridge@samba.org>
2012-03-11 20:59:47 +11:00
4f739ea28f
make 'ENABLE' and 'ENABLED' mean the same things
...
users get this wrong far too often!
2012-03-10 10:34:33 +11:00
aa4beb9753
APM: make it possible to build ArduPlane with quaternion support
2012-03-10 10:34:29 +11:00
c6f3f7065c
APM: the CLI fits nicely on the 1280 again now
...
I find the CLI very useful for testing, so enable it by default on the
1280. Logging is still off by default.
2012-02-14 08:33:49 +11:00
3b2196354f
Stashing some battery monitoring ratio values in the comments for future use.
2012-01-15 16:35:46 -07:00
17b31d0b5b
Fix airspeed sensor support for APM2.
...
Airspeed sensor should be attached to Analog input 0
2012-01-15 16:12:08 -07:00
fd8dc84fac
Update battery monitoring code for ArduPlane
...
Fixes compatibility for APM2. Also a significant update to the battery monitoring code: We previously had monitoring modes for individual cell voltages for 3 and 4 cell lipos. These have been removed as they were never really supported (the cell voltages were computed but were not reported or recorded anywhere). Also, some clean-up/prep work was done for supporting monitoring 2 separate battery packs. The CLI battery and current monitoring tests were consolidated into 1 test.
2012-01-15 16:10:28 -07:00
5d5800ee1f
fix relay on apm 1 AP
2012-01-05 07:51:01 +08:00
968ad78df0
APM2: default magnetometer to enabled
...
all APM2s have a MAG at the moment
thanks to Chris for the suggestion
2011-12-22 17:51:14 +11:00
Andrew Tridgell
rmackay9
Craig Elder
Amilcar Lucas
uncrustify
Jason Short
Michael Oborne
James Goppert
Adam M Rivera
Doug Weibel