Andrew Tridgell
d952ccf968
Copter: added main_loop_ready() function
...
this tells us when the main loop is ready to run. MAVLink won't send a
message if the main loop could run.
2013-01-07 11:07:34 +11:00
Andrew Tridgell
c48714be16
Copter: enabled PX4 sensors
2013-01-05 20:39:31 +11:00
James Bielman
264db3670e
AP_Baro: Add CONFIG_MS5611_SERIAL option to choose between SPI and I2C.
...
- Update ArduCopter and ArduPlane modules to pass the correct serial
driver to the MS5611 driver.
- Update barometer examples, assuming SPI.
2013-01-03 13:48:06 -08:00
Andrew Tridgell
94e3322e24
Copter: fixed build on px4
2013-01-02 22:09:02 +11:00
Andrew Tridgell
e56a7eacec
Copter: don't pass board version to motors
2013-01-02 15:28:34 +11:00
Andrew Tridgell
ead38f917f
Copter: use GRAVITY_MSS
2013-01-02 14:45:08 +11:00
rmackay9
228ad2198f
ArduCopter: update firmware version to 2.9-rc2
2013-01-02 09:55:37 +11:00
rmackay9
677b38a48e
ArduCopter: first implementation of surface tracking using sonar
...
Note: not yet enabled as part of any flight mode
2013-01-02 09:55:37 +11:00
rmackay9
68b62abd38
ArduCopter with the new Camera and Relay classes for APM1 and APM2.
...
All changes by Sandro Benigno
2013-01-02 09:55:37 +11:00
rmackay9
e850ab7ccd
ArduCopter: add AUTO_VELZ_MIN, AUTO_VELZ_MAX and PILOT_VELZ_MAX to allow better control of climb/descent rate in auto and manual throttle modes
2013-01-02 09:24:31 +11:00
Craig@3DR
0ed25cf719
Global change all references from
...
GPS_PROTOCOL_MTK16
to
GPS_PROTOCOL_MTK19
2013-01-02 09:24:31 +11:00
rmackay9
466097b383
ArduCopter: use inertial nav for current altitude and climb rate
2013-01-02 09:22:51 +11:00
rmackay9
5ba363b007
ArduCopter: move gcs_check function (which sends to ground station) to run when 50hz loop is not running
...
Also removed redundant heartbeat message
2013-01-02 09:21:35 +11:00
rmackay9
bd0e018ca0
ArduCopter: restore auto-trim method but now use AHRS.add_trim
2013-01-02 09:20:08 +11:00
Robert Lefebvre
6e64b1b357
ACM: Precision Loiter RePositioning code.
...
Protected behind a #define
2013-01-02 09:19:39 +11:00
rmackay9
e6519330f4
ArduCopter: remove unused rc_override variables to save 21 bytes
2013-01-02 09:19:17 +11:00
rmackay9
ac8af9a53f
ArduCopter: Leonard Hall's changes to alt hold including adding low pass filter to climb rate
...
get_throttle_rate_stabilized changed to simply update the target altitude instead of talking directly to the rate controller.
get_throttle_althold changed to use sqrt of distance when calculating the desired rate towards the target altitude.
added reset of accel based throttle PID's I term.
unrelated small bug fix from Randy to allow CH6 tuning of throttle rate D term.
2013-01-02 09:19:17 +11:00
rmackay9
d926360e81
ArduCopter: move gcs updates to run only when there are 4ms of spare time before the next 100hz iteration starts
2013-01-02 09:14:31 +11:00
rmackay9
6da68c53a5
ArduCopter: bug fix so AP_Limits does not use up memory if it is disabled
2013-01-02 09:13:42 +11:00
rmackay9
5633164fa0
ArduCopter: bug fix for compass.accumulate check in main loop (millis vs micros issue)
2013-01-02 09:12:40 +11:00
rmackay9
8e032b89ee
ArduCopter: create 2.9 branch and update firmware version
2013-01-02 09:10:40 +11:00
Andrew Tridgell
06357c40f2
Copter: use new functions
2012-12-20 14:53:22 +11:00
Andrew Tridgell
a02f723f3a
Copter: fixed HIL builds
2012-12-20 14:52:37 +11:00
Andrew Tridgell
9e986801c9
Copter: fixed SITL for ArduCopter
2012-12-20 14:52:34 +11:00
Andrew Tridgell
08b1c2d590
Copter: fixed GPS init
2012-12-20 14:52:33 +11:00
Pat Hickey
d5d97be837
ArduCopter: add param loader properly implement parameters
...
* thanks tridge!
2012-12-20 14:52:29 +11:00
Pat Hickey
5e63491994
ArduCopter: fix issues with HAL/HIL mixup and baro/compass instances
2012-12-20 14:52:29 +11:00
Pat Hickey
21d0da84a6
ArduCopter: temporarily disable AP_Param::setup_sketch_results
...
* rebased away tridge's AP_Param changes as they seemed possibly buggy?
2012-12-20 14:52:29 +11:00
Pat Hickey
a0151aa66c
ArduCopter: fix cliSerial null ptr, do AP_Param::setup_sketch_defaults
...
* plus make SITL DataFlash available.
2012-12-20 14:52:29 +11:00
Pat Hickey
2aa4657315
ArduCopter: changes to use CONFIG_HIL_BOARD
2012-12-20 14:52:28 +11:00
Pat Hickey
ade7099d75
ArduCopter: add AP_HAL_MAIN
2012-12-20 14:52:28 +11:00
Pat Hickey
5bd7046a95
ArduCopter: sketch cpp builds!
2012-12-20 14:52:28 +11:00
Pat Hickey
7af03127f6
ArduCopter: more work
2012-12-20 14:52:28 +11:00
Pat Hickey
70f4739522
ArduCopter: more fixes
2012-12-20 14:52:28 +11:00
Pat Hickey
f281d9265e
ArduCopter: reworked sonar analog source creation
2012-12-20 14:52:28 +11:00
Pat Hickey
d9e0bbbbab
ArduCopter: first pass at AP_HAL porting
...
* changed all the byte types to uint8_t
* fixed up much of the serial stuff
2012-12-20 14:52:27 +11:00
Pat Hickey
a4f1f6a5db
AP_Progmem: fix dependencies for all sketches touched by AP_HAL_AVR
2012-12-20 14:51:28 +11:00
Pat Hickey
3f1d9d7f69
AP_Param: #include <AP_Param.h> fixups for libraries & sketches
...
* I mostly went through with grep and added an #include <AP_Param.h> below
every #include <AP_Common.h>. Not all of these example sketches might
strictly need AP_Param.
2012-12-20 14:51:19 +11:00
Jason Short
19ae5c30eb
ACM : Formatting
2012-12-13 20:12:39 -08:00
rmackay9
047f848cc7
ArduCopter: remove ThirdOrderCompFilter from list of includes
2012-12-10 09:14:44 +09:00
rmackay9
0f7bb79d89
ArduCopter: add comments to tuning parameters.
...
Use RC_CHANNEL types as defined by RC_Channel library.
Remove unused definitions.
2012-12-09 16:44:42 +09:00
rmackay9
8c2423f618
ArduCopter: code clean-up. Changed update_nav_wp to use a switch statement and relocated to navigation.pde
2012-12-09 15:24:19 +09:00
rmackay9
b4e5176e2a
ArduCopter, AP_InertialSensor: restore mpu6k sample rate to 200hz but keep default filtering at 42hz.
2012-12-09 14:27:33 +09:00
Robert Lefebvre
0eb57bf93d
ACM: TradHeli
...
Fix to make update_throttle_cruise work with stab_throttle scaling.
2012-12-08 15:12:39 -05:00
rmackay9
9dd978576b
ArduCopter: auto yaw changes to allow pilot override of yaw during missions
...
Added set_yaw_mode to better control of yaw controller changes and variable initialisation.
Replaced AUTO_YAW mode with separate yaw controllers YAW_LOOK_AT_NEXT_WP, YAW_LOOK_AT_LOCATION, YAW_LOOK_AT_HEADING.
Pilot manual override of yaw causes yaw to change to YAW_HOLD (i.e. manual yaw) until next waypoint is reached.
Added get_yaw_slew function to control how quickly autopilot turns copter
Changed YAW_LOOK_AHEAD to use GPS heading and moved to new get_look_ahead_yaw function in Attitude.pde
Renamed variables: target_bearing->wp_bearing, original_target_bearing->original_wp_bearing.
Removed auto_yaw_tracking and auto_yaw variables and update_auto_yaw function as they are no longer needed.
Simplified MAV_CMD_CONDITION_YAW handling (do_yaw). We lose ability to control direction of turn and ability to do long panorama shots but it now works between waypoints and save 20bytes.
2012-12-08 14:23:32 +09:00
rmackay9
99b32a39c4
ArduCopter: InertialNav time constant CH6 tuning changed to only update enabled axis
2012-12-07 13:01:40 +09:00
rmackay9
39d524212f
ArduCopter: allow accel based throttle controller to be enabled/disabled with the new THR_ACC_ENABLE parameter.
...
When disabled the original velocity based throttle controller is used.
2012-12-06 10:31:57 +09:00
rmackay9
a5bb54e36e
ArduCopter: RTL clean-up and slightly improved landing sensor
...
Consolidated RTL state to be captured by rtl_state variable.
Combined update_RTL_Nav and verify_RTL functions which performed the same function but one was for missions, the other for the RTL flight mode.
Renamed some RTL parameters and global variables to have RTL at the front.
Landing detector now checks accel-throttle's I term and/or a very low throttle value
2012-12-06 10:31:52 +09:00
rmackay9
072ffec493
ArduCopter: allow INERTIAL_NAV to be enabled separately for horizontal and vertical position
2012-12-06 10:31:41 +09:00
rmackay9
d7f76ebd87
ArduCopter: add tuning of throttle rate controller's I term (THROTTLE_KI)
2012-12-06 10:31:25 +09:00
