Jacob Walser
|
0223cf70ed
|
Sub: better check and text message for baro calibration failure
|
2018-04-23 15:12:35 -04:00 |
Jacob Walser
|
7caca6a251
|
Sub: reduce default ACRO_YAW_P by 25% to 3.375
|
2018-04-23 15:12:35 -04:00 |
Jacob Walser
|
4fae5cdfcf
|
Sub: disarm motors if failsafe action fails
|
2018-04-23 15:12:35 -04:00 |
Jacob Walser
|
4fe8746a2a
|
Sub: remove arbitrary scalars from manual mode inputs
fix bluerobotics/ardusub#150
|
2018-04-23 15:12:35 -04:00 |
murata
|
3577def8fd
|
AC_Avoid: use elseif because value does not change
|
2018-04-23 19:45:50 +09:00 |
murata
|
29b1a6ed41
|
AC_Avoid: fix comment
|
2018-04-23 19:45:37 +09:00 |
Randy Mackay
|
7f7a588002
|
Tools: add accel and turn-rate max and increase steering angle P
these parameters were added to Rover-3.3
|
2018-04-23 11:06:34 +09:00 |
malcolm churn
|
7718196838
|
HAL_ChibiOS: Fix sparky2 target.
Correct pin mappings, ADC, PWM.
Not working
Flash memory, Logging, external i2c tested with NXP MAG3110.
|
2018-04-22 21:01:14 +10:00 |
Randy Mackay
|
2fff9561a7
|
Copter: 3.6.0-rc1 release notes
|
2018-04-21 09:22:42 +09:00 |
Andrew Tridgell
|
e2fa38968f
|
AP_BoardConfig: fixed build for some boards
for boards that don't have board detection but do have a safety switch
this fixes the build
|
2018-04-21 08:45:34 +10:00 |
Pierre Kancir
|
3be6c0e26b
|
ArduCopter : clean unused definitions
|
2018-04-20 15:26:47 +01:00 |
Jacob Walser
|
c76ff32aa1
|
Sub: Do not report altitude in GLOBAL_POSITION_INT if there is no depth
sensor connected
Fix bluerobotics/ardusub#145
|
2018-04-19 14:58:06 -04:00 |
Patrick José Pereira
|
0878f5044c
|
Sub: Send a clear message if depth sensor is not connected
Fix bluerobotics/ardusub#151
Signed-off-by: Patrick José Pereira <patrickelectric@gmail.com>
|
2018-04-19 07:45:00 -07:00 |
Randy Mackay
|
8fa1700d02
|
Rover: 3.3.0-rc1 release notes
|
2018-04-19 17:20:38 +09:00 |
Randy Mackay
|
87eef9051f
|
Rover: increase default pivot turn angle to 60deg
pivoting at only 30degrees of error could lead to endless twitching back and forth for poorly tuned rovers
|
2018-04-19 16:32:48 +09:00 |
Randy Mackay
|
23ed735304
|
AR_AttitudeControl: reduce default steering I gain to 0.2
Also reduce default filter from 50hz to 10hz
|
2018-04-19 16:29:12 +09:00 |
Randy Mackay
|
e5c0b1814a
|
GCS_MAVLink: remove underscore from method names
|
2018-04-19 13:38:22 +09:00 |
Vince Kurtz
|
2f81747112
|
GCS_MAVLink: fix VISP logging
log VISP messages for the ATT_POS_MOCAP mavlink message as well
|
2018-04-19 13:34:49 +09:00 |
Peter Barker
|
9480572075
|
AP_Notify: ChibiOS: beep on mode change
|
2018-04-19 09:29:41 +10:00 |
Peter Barker
|
557f8cee43
|
AP_HAL_ChibiOS: add mode-change-beeps
|
2018-04-19 09:29:41 +10:00 |
mirkix
|
79f3fd532b
|
AP_HAL_ChibiOS: fix spi clock calculation
|
2018-04-19 08:32:31 +10:00 |
Peter Barker
|
5b03835103
|
Tools: autotest: correct pattern match in get_parameter
|
2018-04-18 20:31:55 +09:00 |
Peter Barker
|
802e4c6315
|
Tools: autotest: add tests for relays
|
2018-04-18 20:31:55 +09:00 |
Peter Barker
|
e7b5978d8d
|
SITL: use a 16-bit mask for GPIO out
|
2018-04-18 20:31:55 +09:00 |
Peter Barker
|
1eecf07e68
|
AP_HAL_SITL: use a 16-bit mask for GPIO out
This allows Relay pins to be represented (typically pin 13)
|
2018-04-18 20:31:55 +09:00 |
Peter Barker
|
c7327acef7
|
Sub: use AP_ServoRelayEvents singleton
|
2018-04-18 20:31:55 +09:00 |
Peter Barker
|
5cc98a9733
|
Plane: use AP_ServoRelayEvents singleton
|
2018-04-18 20:31:55 +09:00 |
Peter Barker
|
4b5953734d
|
Copter: use AP_ServoRelayEvents singleton
|
2018-04-18 20:31:55 +09:00 |
Peter Barker
|
80f0016951
|
Tracker: use AP_ServoRelayEvents singleton
|
2018-04-18 20:31:55 +09:00 |
Peter Barker
|
d66cb1dda0
|
Rover: use AP_ServoRelayEvents singleton
|
2018-04-18 20:31:55 +09:00 |
Peter Barker
|
682679c68d
|
GCS_MAVLink: use AP_ServoRelayEvents singleton
|
2018-04-18 20:31:55 +09:00 |
Peter Barker
|
544ac03ca6
|
AP_ServoRelayEvents: add singleton
|
2018-04-18 20:31:55 +09:00 |
ChristopherOlson
|
9aa685a6d8
|
AP_Motors:TradHeli - single rotor only - add support for H3-140 swashplates.
Also changes the old definition to H3 for swashplates with fixed control radius and adjustable servo position.
|
2018-04-18 14:24:59 +09:00 |
ChristopherOlson
|
f073c58f68
|
AP_Motors:TradHeli - add support for reverse collective swashplates
|
2018-04-18 14:24:59 +09:00 |
Peter Barker
|
f3c9761901
|
Tracker: GPS now logs its own data
|
2018-04-18 13:50:55 +09:00 |
Peter Barker
|
a10c843e6e
|
Sub: GPS now logs its own data
|
2018-04-18 13:50:55 +09:00 |
Peter Barker
|
5ef417a669
|
Plane: GPS now logs its own data
|
2018-04-18 13:50:55 +09:00 |
Peter Barker
|
04885b127c
|
Copter: GPS now logs its own data
|
2018-04-18 13:50:55 +09:00 |
Peter Barker
|
64a8de42da
|
DataFlash: use singleton for getting hold of gps object
|
2018-04-18 13:50:55 +09:00 |
Peter Barker
|
901ba0034c
|
AP_NavEKF3: do not pass GPS into Log_Write_GPS; it uses singleton
|
2018-04-18 13:50:55 +09:00 |
Peter Barker
|
578facc9ad
|
AP_NavEKF2: do not pass GPS into Log_Write_GPS; it uses singleton
|
2018-04-18 13:50:55 +09:00 |
Peter Barker
|
e73a02343a
|
Rover: GPS now logs its own data
|
2018-04-18 13:50:55 +09:00 |
Peter Barker
|
643e7e039a
|
AP_GPS: log received data
Also log a set of flag values if a driver is deleted
|
2018-04-18 13:50:55 +09:00 |
Peter Barker
|
8648db06b4
|
Copter: create autoyaw.cpp from all the bits of Copter::Mode::AutoYaw
|
2018-04-18 13:27:43 +09:00 |
Peter Barker
|
948b90ed97
|
Copter: rename roi_WP to just roi
A Vector3f is not a waypoint.
This should really be "Point Of Interest" rather than "Region Of
Interest"
|
2018-04-18 13:27:43 +09:00 |
Peter Barker
|
ba8b3e2415
|
Copter: create an AutoYaw helper object to hold auto-yaw state
|
2018-04-18 13:27:43 +09:00 |
Tom Pittenger
|
63e42e194f
|
GCS_MAVLink: send correct mission_ack result type
has no effect since the two typedef enums equated to same value
|
2018-04-18 12:02:43 +09:00 |
Pierre Kancir
|
1f30ae3076
|
ArduCopter: fix float to double warning
|
2018-04-18 10:27:10 +09:00 |
Karthik Desai
|
75ae59c0c8
|
Autotest: Remove frame initialisation.
This will otherwise override the --frame parameter. The init() function takes care of the initialisation
|
2018-04-17 23:00:04 +10:00 |
Pierre Kancir
|
fdfa08c586
|
AP_AHRS: fix include order due to cyclic include
|
2018-04-17 17:21:35 +09:00 |