Randy Mackay
fc0c451b69
Copter: remove #ifdef checks for Atmega1280
2013-04-05 22:48:10 +09:00
Randy Mackay
a9eb626cb8
Copter: update default Rate Yaw P to 0.20 (was 0.25)
2013-04-01 11:49:50 +09:00
Randy Mackay
36834e77b5
Copter: remove support for CLI Slider
2013-03-18 14:07:04 +09:00
Randy Mackay
597a4b912a
Copter: fix to allow building HIL_MODE_SENSORS
2013-03-18 13:41:52 +09:00
Randy Mackay
d1344e8c39
Copter: remove #define for CROSSTRACK_GAIN
...
Note: the cross track is still calculated inside the inertial nav based
loiter and wp controls but it's no longer requires a tunable parameter
2013-03-17 16:56:18 +09:00
Randy Mackay
1b6fcad90a
Copter: remove tilt compensation parameter
...
Note: this idea of feed forward tilt compensation is being incorporated
into the inertial nav based loiter and wp controllers but does not
require a separate tunable parameter
2013-03-17 16:53:32 +09:00
Randy Mackay
fdcb78ccf7
Copter: leonard's smoother alt-hold transition
...
Target altitude when entering alt-hold is based on a projection from
current alt and climb rate
2013-03-17 13:24:49 +09:00
Randy Mackay
150046f2b8
Copter: GPS Failsafe implemented
...
Switches to LAND mode 5 seconds after losing GPS if you're in a flight
mode that requires a GPS
2013-03-16 17:27:46 +09:00
Randy Mackay
a73f50494c
TradHeli: remove duplicate RC_FAST_SPEED definition
2013-03-04 23:45:23 +09:00
Randy Mackay
33bd984a91
Copter: remove unused input_voltage parameter
2013-03-03 23:23:54 +09:00
Randy Mackay
d6ff5ae261
Copter: add roll-pitch slew for auto modes
...
Added reporting of roll, pitch inputs for ACRO, AUTO
2013-02-24 14:42:04 +09:00
Randy Mackay
e297ba7d18
Copter: update default loiter gains for inertial nav
2013-02-24 14:42:00 +09:00
Randy Mackay
cbde042ec5
Copter: remove non-inav loiter and wp controllers
...
lon_speed, lat_speed changed to float
do_takeoff, do_land now set roll-pitch, yaw and nav modes specifically
removed fast_corners functionality (may need to be reimplemented with
new inertial nav controllers)
2013-02-24 14:41:52 +09:00
Randy Mackay
609676e26c
Copter: add logging of compass values
...
Removed rarely used ITERM because we didn't have enough bits in the log
mask
2013-02-24 14:41:48 +09:00
Randy Mackay
67c69a19ee
Copter: remove baro-only alt hold
...
Saves 8 bytes of memory and more importantly simplifies the alt hold
calculations
2013-02-24 14:41:29 +09:00
Randy Mackay
fcf102b2cf
Copter: inertial nav waypoint controller
...
#define added to allow compile time selection of traditional or inav
based loiter and wp controllers
2013-02-24 14:41:09 +09:00
Randy Mackay
8e4c9518ea
Copter: increase low voltage check to 10.5v
...
Change requested by Rob Lefebvre and Richie Wilson
2013-02-23 00:36:51 +09:00
Andrew Tridgell
4c7a1a1806
Copter: change PX4 main baud rate back to 115200
...
we now use USB console
2013-02-22 07:04:23 +11:00
Randy Mackay
06a71af12f
Copter: THR_MID used to scale manual throttle
2013-02-01 22:37:16 +09:00
Randy Mackay
ce370bab0c
Copter: rename CUR and CURR to CURRENT for logging
...
Based on user complaint that enable/disable was using CUR while message
was appearing as CURR
2013-01-26 17:20:41 +09:00
Randy Mackay
b74fe10aa9
Copter: set each flight mode's nav_mode
...
Allow ACRO flight mode's roll, pitch, yaw, throttle and nav mode to be
overwritten
2013-01-25 15:57:55 +09:00
Andrew Tridgell
f303554259
Copter: run serial0 at 57600 on PX4
2013-01-22 09:50:22 +11:00
Robert Lefebvre
dde713aaa5
Arducopter: Backing out my changes for a new Loiter Repositioning mode. Leonard and Jonathan's work will trump this.
2013-01-20 21:32:00 +09:00
Andrew Tridgell
580abf1106
Copter: fixed PX4 mag orientation
2013-01-17 17:23:34 +11:00
James Bielman
5631f865b2
Update floating point calculations to use floats instead of doubles.
...
- Allows use of hardware floating point on the Cortex-M4.
- Added "f" suffix to floating point literals.
- Call floating point versions of stdlib math functions.
2013-01-16 13:52:01 +11:00
Randy Mackay
fef7569dee
Copter: added experimental LOITER_REPOSITIONING #define to config.h
...
APM_Config.h should be used to overriding the standard parameters but
they still require a definition in config.h or they will be undefined
when built by the mission planner.
2013-01-14 13:34:14 +09:00
Randy Mackay
9ad6f711f8
ArduCopter: replace FS_THR_RTL_MIN_DISTANCE with wp_radius
...
This effectively means that an RTL kicked off by a failsafe will
immediately switch to LAND mode only if within 2 meters. Previously the
radius was much wider (15m).
2013-01-13 20:00:47 +11:00
Randy Mackay
12f885c33c
ArduCopter: disable ITERM logging by default
...
This message takes 1ms to write and we are running over our limits on
some loops.
2013-01-13 20:00:39 +11:00
rmackay9
21b6c78d12
ArduCopter: added get_throttle_althold_with_slew to allow slower altitude target changes
...
Improved surface tracking by using slewed althold controller
Reduced sonar mode filter to just 3 elements to reduce lag but at the possible consequence of allowing sonar noise to creep through for people with margin sonar set-ups.
2013-01-13 19:51:47 +11:00
Randy Mackay
87627d883b
ArduCopter: use new logging method for remaining packet types
...
Additional changes include renaming RAW dataflash type to IMU
2013-01-13 00:17:44 +09:00
James Bielman
7827a4a54a
ArduCopter: Add AP_HAL_SMACCM support.
...
- Added default configuration to "config.h".
- Added main function to run under FreeRTOS with HWF4.
2013-01-09 11:19:51 -08:00
James Bielman
ab37f833db
MS5611: Fix CONFIG_MS5611_SERIAL definitions.
...
- Make sure the values are defined as integers. We were always using
SPI rather than using I2C when desired.
2013-01-09 11:19:51 -08:00
Andrew Tridgell
c48714be16
Copter: enabled PX4 sensors
2013-01-05 20:39:31 +11:00
James Bielman
264db3670e
AP_Baro: Add CONFIG_MS5611_SERIAL option to choose between SPI and I2C.
...
- Update ArduCopter and ArduPlane modules to pass the correct serial
driver to the MS5611 driver.
- Update barometer examples, assuming SPI.
2013-01-03 13:48:06 -08:00
Andrew Tridgell
94e3322e24
Copter: fixed build on px4
2013-01-02 22:09:02 +11:00
rmackay9
9b2956b377
ArduCopter: increase throttle rate P to 6.0 (was 1.0) and alt hold P to 2.0 (was 1.0)
2013-01-02 09:55:37 +11:00
rmackay9
d400e5040b
ArduCopter: turn on INERTIAL_NAV_Z in the config.h file so that it takes effect when built for the mission planner
2013-01-02 09:55:37 +11:00
rmackay9
e850ab7ccd
ArduCopter: add AUTO_VELZ_MIN, AUTO_VELZ_MAX and PILOT_VELZ_MAX to allow better control of climb/descent rate in auto and manual throttle modes
2013-01-02 09:24:31 +11:00
rmackay9
5526ca204c
ArduCopter: on throttle failsafe, only initiate RTL if we are at least 15m from home
2013-01-02 09:22:51 +11:00
Robert Lefebvre
6e64b1b357
ACM: Precision Loiter RePositioning code.
...
Protected behind a #define
2013-01-02 09:19:39 +11:00
rmackay9
e6519330f4
ArduCopter: remove unused rc_override variables to save 21 bytes
2013-01-02 09:19:17 +11:00
rmackay9
34e18ae12a
ArduCopter: increase accel based throttle PIDs and add D term to rate based throttle
2013-01-02 09:19:17 +11:00
Robert Lefebvre
9605bd8ee1
ACM: Trying to set a default MPU6K filter rate of 10Hz for TradHeli. Doesn't Work.
2013-01-02 09:14:55 +11:00
rmackay9
d8e3d5c10c
ArduCopter: allow RTL's yaw mode to be overridden with a #define in APM_Config.h
2013-01-02 09:12:40 +11:00
rmackay9
50d46898fb
ArduCopter: allow GUIDED mode roll-pitch, yaw and throttle control modes to be overridden
2013-01-02 09:12:17 +11:00
Andrew Tridgell
9e986801c9
Copter: fixed SITL for ArduCopter
2012-12-20 14:52:34 +11:00
Pat Hickey
5e63491994
ArduCopter: fix issues with HAL/HIL mixup and baro/compass instances
2012-12-20 14:52:29 +11:00
Pat Hickey
d93d932831
ArduCopter: defines fixes
...
Conflicts:
libraries/AP_Common/Arduino.mk
2012-12-20 14:52:28 +11:00
Pat Hickey
2aa4657315
ArduCopter: changes to use CONFIG_HIL_BOARD
2012-12-20 14:52:28 +11:00
rmackay9
2f748f8382
ArduCopter: renamed BATT_FAILSAFE to FS_BATT_ENABLE
2012-12-10 23:47:14 +09:00