Craig3DRobotics
630095adaa
Revert "Copter: Corrected SR0 & SR3 parameter descriptions"
...
This reverts commit 6568234018
.
2013-09-06 09:58:19 -07:00
Craig3DRobotics
f1a674ad26
Copter: Correction on SR0 & SR3 parameter description.
2013-09-05 22:28:34 -07:00
Andrew Tridgell
52f5b1e5a7
Copter: update to GPLv3 license headers
2013-08-30 13:01:39 +10:00
Craig3DRobotics
6568234018
Copter: Corrected SR0 & SR3 parameter descriptions
2013-08-29 12:19:04 -07:00
Randy Mackay
fd047cc968
Copter: AUTO ch7/ch8 option
2013-08-19 18:09:23 +09:00
Randy Mackay
3a5a15a15f
Copter: allow CH6 tuning of sonar gain
2013-08-18 15:44:54 +09:00
Randy Mackay
d000967a76
Copter: pre-arm check for gps hdop < 2
2013-08-15 13:06:36 +09:00
Randy Mackay
6969ab573d
Copter: configurable max lean angle
...
ANGLE_MAX parameter allows limiting the roll and pitch angles during
manual and auto flight modes to anywhere from 10 to 80 degrees
2013-08-11 12:53:22 +09:00
Randy Mackay
74fb500efe
Copter: integrate AC_Sprayer
2013-08-05 21:12:23 +09:00
Randy Mackay
49dbdce89c
Copter: split ACRO_P into ACRO_RP_P and ACRO_YAW_P
2013-08-05 21:05:00 +09:00
Randy Mackay
82082e044c
Copter: remove ACRO's axis enabled parameter
...
Acro is now body frame (with earth frame leveling) while Sport is earth
frame acro
2013-08-05 21:04:57 +09:00
Randy Mackay
786d6824ae
Copter: Acro Trainer added to Ch7/Ch8 switch
2013-08-05 21:04:55 +09:00
Randy Mackay
21e523b9ac
Copter: Acro trainer separated into limited and leveled
2013-08-05 21:04:53 +09:00
Randy Mackay
39ab4f62ef
Copter: add SPORT mode
2013-08-05 21:04:41 +09:00
Randy Mackay
2c48c20088
Copter: generalize 3 pos switch for all ch7/ch8 options
2013-07-29 16:28:04 +09:00
Olivier-ADLER
87d062905e
Copter: 3 positions switch support for CH7 and CH8 - new 3 positions SIMPLE / SUPERSIMPLE mode
...
3 positions modes must use mode number >= 100
pre-arm check correction for CH7 - CH8 check
2013-07-29 15:12:10 +09:00
Randy Mackay
11e7e9eaf1
Copter: WP_YAW_BEHAVIOUR param update for Look Ahead
2013-07-20 15:46:19 +09:00
Randy Mackay
c937fe45e1
Revert "Copter: Remove CH7 & CH8 Enable / Disable of GeoFence"
...
This reverts commit e25b8933f3
.
2013-07-20 15:00:08 +09:00
Craig3DR
e25b8933f3
Copter: Remove CH7 & CH8 Enable / Disable of GeoFence
2013-07-18 17:06:53 +09:00
Andrew Tridgell
0b27bb05d4
Copter: fixed FENCE and WPNAV parameter doc generation
2013-07-18 14:58:24 +10:00
Randy Mackay
aefb38e486
Copter: remove param to disable accel based throttle controller
2013-07-12 22:57:30 +09:00
Randy Mackay
2f4221391e
Copter: set_dead_zone renamed to set_default_dead_zone
...
Dead zones now set as part of rc initialisation instead of only after
eeprom is erased.
Change in use of parameter means value passed in should be 1/2 what it
was previously
2013-07-12 11:44:23 +09:00
Randy Mackay
404cd5f3da
Copter: rename g.pid_throttle to g.pid_throttle_rate
...
Small code clean-up to make throttle rate controller's pid more obvious
2013-06-30 00:04:21 -10:00
Randy Mackay
b3da8a462f
Copter: CH6 tuning definition clean-up
...
Renamed and reorganised the CH6 #defines and parameter definitions
2013-06-29 23:51:43 -10:00
Robert Gayle
917edcab11
Copter: added FS_THR_ENABLED_ALWAYS_LAND (=3) option: don't attempt RTL, just land
2013-06-27 10:19:38 -10:00
Andrew Tridgell
23eade8f74
Copter: enable RELAY_* parameters
2013-06-25 12:46:53 +10:00
Randy Mackay
a48a7f9775
Copter: minor param definition unit changes
2013-06-23 15:52:46 +09:00
Randy Mackay
acb4907313
Copter: update FS_THR_VALUE parameter description
...
One user was setting FS_THR_VALUE too low, below 900 which means
ArduCopter would not trigger when the ppmencoder pulled ch3 low after
updates from the ppmencoder stopped
2013-06-18 15:56:39 +09:00
Randy Mackay
c42ed1e5eb
Copter: add @Increment to PID parameters descriptions
2013-06-16 21:53:50 +09:00
Andrew Tridgell
3ec381094e
Copter: fix VOLT_DIVIDER docs
2013-06-07 08:40:37 +10:00
Andrew Tridgell
8703d39475
Copter: the INS object is needed for HIL_MODE_SENSORS
...
otherwise we can't level, so can't arm
2013-06-04 18:09:06 +10:00
Randy Mackay
213eaa8db6
Copter: integrate draft RCMapper
2013-06-03 16:23:47 +10:00
Andrew Tridgell
2488c4fdc3
Copter: update docs on volt/current pin
2013-05-31 07:57:15 +10:00
Andrew Tridgell
0e31a2f582
Copter: fixed indent-tabs-mode
2013-05-30 09:55:51 +10:00
Randy Mackay
967aa81e9b
Copter: add XL-EZ4 to SONAR_TYPE parameter description
2013-05-23 09:46:57 +09:00
Randy Mackay
c404c46e5a
Copter: add Fence to CH7/CH8 param description
2013-05-21 16:31:16 +09:00
Andrew Tridgell
4508e645f1
Copter: fixed parameters to pass new script
2013-05-21 17:02:13 +10:00
Randy Mackay
bb3073fab1
Copter: minor parameter description fixes
2013-05-21 15:56:09 +09:00
Randy Mackay
5ee68db6f0
TradHeli: add parameter descriptions
...
small formatting changes too
2013-05-21 15:33:41 +09:00
Randy Mackay
9139fb54ac
Copter: param update for AP_Baro and AP_Scheduler
2013-05-21 14:22:11 +09:00
Dr Gareth Owen
e9d640ced8
added ch7 option to reset yaw back to what it was when quad was armed
2013-05-21 10:40:30 +09:00
Randy Mackay
db552adf02
Copter: typo in LOG_BITMASK param description
2013-05-21 10:30:59 +09:00
Randy Mackay
669850e6d4
Copter: add parameter description for LOG_BITMASK
...
Should allow a dropdown in the GCS so it can be set more easily without
going into the cli
2013-05-21 10:29:40 +09:00
Randy Mackay
bd44c2f73d
Copter: all pre-arm checks to be disabled
...
set ARMING_CHECK parameter to zero to disable
2013-05-20 14:48:04 +09:00
Randy Mackay
9fdab5e8fe
Copter: remove unused AUTO_SLEW_RATE parameter
2013-05-17 16:09:17 +09:00
Randy Mackay
8c99936431
Copter: update CH7_OPT, CH8_OPT to include Multi Mode
2013-05-17 16:07:11 +09:00
Randy Mackay
38239c652a
Copter: ch8 aux switch
...
Ch8 can be used as an aux switch like ch7. Has all the same options as
ch7 and there is a safety check to ensure both switches aren't set to
the same function so as to avoid interfering with each other
2013-05-17 14:42:28 +09:00
Randy Mackay
33d1129904
Copter: remove unused TB_RATIO parameter
2013-05-14 16:56:55 +09:00
Randy Mackay
9824f6c223
Copter: add flight mode strings to Parameter info
2013-05-08 16:41:45 +09:00
Randy Mackay
324200b52c
Copter: disable centrifugal correction when disarmed
2013-05-06 15:32:08 +09:00
Randy Mackay
372ebb602c
Copter: disable centrifugal force correction when disarmed
2013-05-05 16:55:06 +09:00
Randy Mackay
1cfd5900a8
Copter: add support for H-quad frame
...
H-quads are like X quads but the motors spin in the opposite direction.
Having the motors reversed seems to help with yaw authority because of
the slight flex in bodies
2013-05-03 23:13:40 +09:00
Michael Oborne
743d7f2b74
Fix Param description
2013-05-02 09:49:21 +10:00
Randy Mackay
bab9fa25e5
Copter: add GCS failsafe
2013-04-29 21:30:22 +09:00
Randy Mackay
58d1da2d80
Copter: integrate AC_Fence in place of limits
...
Lesser functionality than limits but saves more than 150 bytes and it
works
2013-04-27 11:14:07 +09:00
Andrew Tridgell
300a8d2bbc
Copter: support all 12 channels on PX4
...
last 4 channels are on the FMU pins
2013-04-25 20:10:53 +10:00
Randy Mackay
745df9b13c
Copter: add SONAR_GAIN to tune reaction to sonar
...
Some users report the response to sonar is too violent, this allows that
reaction to be reduced
2013-04-20 15:58:36 +09:00
Randy Mackay
a53e5f747b
Copter: add fourth yaw behaviour, look-at-home
...
Added get_wp_yaw_mode to remove duplication of checks of the
WP_YAW_BEHAVIOR parameter
2013-04-20 15:36:24 +09:00
Randy Mackay
37abfdc65a
Copter: make CIRCLE_RATE a tunable parameter
...
Also bug fix to check of how many time it has rotated during a loiter
turns mission command
2013-04-20 12:03:55 +09:00
Randy Mackay
0fc9c8739e
Copter: add WP_YAW_BEHAVE parameter
...
Allows user to control whether nose points towards next waypoint and/or
home when RTLing.
Replaces YAW_OVR_BEHAVE which had a very similar purpose. Almost nobody
ever knew about or used this parameter.
2013-04-18 15:30:18 +09:00
Randy Mackay
f5955d8915
Copter: auto climb and descent params removed
...
These params now reside in the AC_WPNav library
2013-04-18 14:52:21 +09:00
Randy Mackay
b8974dec99
Copter: compass learn off by default
2013-04-16 18:47:39 +09:00
Randy Mackay
b48864e1ad
Copter: allow CH6 tuning of compass declination
2013-04-15 21:50:44 +09:00
Randy Mackay
629d23b7e2
Copter: remove WP_SPEED and WP_RADIUS parameters
...
AC_WPNav library has equivalent params with very similar names
2013-04-14 13:27:37 +09:00
Randy Mackay
bffe4fa412
Copter: remove NAV_LAT and NAV_LON
...
Loiter and navigation controllers now combined
2013-04-14 12:09:45 +09:00
Randy Mackay
2db8365c90
Copter: add AC_WPNav to parameters list
2013-04-14 10:39:02 +09:00
Randy Mackay
0be23c8090
Copter: fix THR_ALT_P documentation
2013-04-03 22:38:34 +09:00
Randy Mackay
1b6fcad90a
Copter: remove tilt compensation parameter
...
Note: this idea of feed forward tilt compensation is being incorporated
into the inertial nav based loiter and wp controllers but does not
require a separate tunable parameter
2013-03-17 16:53:32 +09:00
Randy Mackay
61e29173e3
Copter: remove unused crosstrack variables and parameters
...
Cross track is still calculated internally to the wpnav controller so we
should move this to a library and still report it to the ground station
2013-03-17 16:46:31 +09:00
Randy Mackay
150046f2b8
Copter: GPS Failsafe implemented
...
Switches to LAND mode 5 seconds after losing GPS if you're in a flight
mode that requires a GPS
2013-03-16 17:27:46 +09:00
Randy Mackay
33bd984a91
Copter: remove unused input_voltage parameter
2013-03-03 23:23:54 +09:00
Randy Mackay
cb84ec9d9b
Copter: add current based compass compensation
2013-03-03 23:02:36 +09:00
Randy Mackay
d6ff5ae261
Copter: add roll-pitch slew for auto modes
...
Added reporting of roll, pitch inputs for ACRO, AUTO
2013-02-24 14:42:04 +09:00
Randy Mackay
67c69a19ee
Copter: remove baro-only alt hold
...
Saves 8 bytes of memory and more importantly simplifies the alt hold
calculations
2013-02-24 14:41:29 +09:00
Randy Mackay
06a71af12f
Copter: THR_MID used to scale manual throttle
2013-02-01 22:37:16 +09:00
Michael Oborne
74e3d64e62
AC Fix BATT_CURR_PIN number
2013-01-20 06:33:29 +08:00
Randy Mackay
5418827f22
Copter: update parameter descriptions for FRAME and CH7_OPT
2013-01-14 15:49:26 +09:00
Randy Mackay
98f5e27dc3
Copter: small correction to RTL_ALT_FINAL param description
2013-01-14 15:21:19 +09:00
Andrew Tridgell
dcb181d2d8
Copter: use new AP_Scheduler library
2013-01-12 12:02:57 +11:00
Andrew Tridgell
21e979910f
Copter: improved 'FRAME' docs
2013-01-10 15:44:13 +11:00
rmackay9
ed79e8c954
ArduCopter: correct TRIM_THROTTLE parameter comments
2013-01-03 00:39:18 +09:00
rmackay9
ba8e9c8f9e
ArduCopter: revert path for reading gcs parameter descriptions
2013-01-02 23:51:27 +09:00
rmackay9
d56e9cc701
ArduCopter: change path for GCS_Mavlink parameter descriptions
2013-01-02 23:42:05 +09:00
rmackay9
4ef7e7b1c6
ArduCopter: add parameter descriptions for GCS_Mavlink objects
2013-01-02 23:36:48 +09:00
rmackay9
886329898c
ArduCopter: minor fixup to a few parameter descriptions
2013-01-02 18:50:25 +09:00
rmackay9
ac028cca74
ArduCopter: remove spaces to allow MP to parse RC Channel parameter descriptions
2013-01-02 18:40:59 +09:00
rmackay9
42a5d183da
ArduCopter: added parameter descriptions for optflow, throttle and loiter pid controllers
2013-01-02 18:32:11 +09:00
rmackay9
ffa923981c
ArduCopter: added parameter description for navigation and some throttle controllers
2013-01-02 17:44:21 +09:00
rmackay9
4a975d35ce
ArduCopter: add parameter descriptions for loiter's lat and lon rate controllers
2013-01-02 17:20:58 +09:00
rmackay9
c595a1e9a2
ArduCopter: updated parameters for roll, pitch and yaw rate controllers.
...
Also added reference to AP_Motors_Class.cpp so that parameter descriptions can be seen in mission planner.
2013-01-02 17:05:57 +09:00
Robert Lefebvre
b9594e7123
Parameters: Fixing a typo
2013-01-01 20:13:00 -05:00
rmackay9
68b62abd38
ArduCopter with the new Camera and Relay classes for APM1 and APM2.
...
All changes by Sandro Benigno
2013-01-02 09:55:37 +11:00
rmackay9
e850ab7ccd
ArduCopter: add AUTO_VELZ_MIN, AUTO_VELZ_MAX and PILOT_VELZ_MAX to allow better control of climb/descent rate in auto and manual throttle modes
2013-01-02 09:24:31 +11:00
rmackay9
6da68c53a5
ArduCopter: bug fix so AP_Limits does not use up memory if it is disabled
2013-01-02 09:13:42 +11:00
Robert Lefebvre
ab95f04a91
ACM: TradHeli
...
Change name of attitude rate feed-forward parameters.
2013-01-02 09:10:40 +11:00
Andrew Tridgell
9e986801c9
Copter: fixed SITL for ArduCopter
2012-12-20 14:52:34 +11:00
rmackay9
af77425636
ArduCopter: fix Failed to Init Optflow message at startup
2012-12-11 00:09:45 +09:00
rmackay9
2f748f8382
ArduCopter: renamed BATT_FAILSAFE to FS_BATT_ENABLE
2012-12-10 23:47:14 +09:00
rmackay9
d31efebd44
ArduCopter: rename throttle failsafe parameters.
...
Switch to LAND flight mode if throttle failsafe triggers and we do not have a GPS.
THR_FAILSAFE renamed to FS_THR_ENABLE.
THR_FS_VALUE renamed to FS_THR_VALUE.
THR_FS_ACTION removed (action is now controlled by setting FS_THR parameter).
2012-12-10 23:38:43 +09:00
rmackay9
2f1b2b70e6
ArduCopter: added ACRO_TRAINER parameter to allow enabling/disabling the acro training function which will bring the roll back to within +- 45 degrees
2012-12-10 22:27:46 +09:00
rmackay9
dadad8677e
ArduCopter: added descriptions for most parameters that did not have them
...
Renamed loiter_radius to circle_radius to better reflect it's purpose.
Removed some unused parameters including WP_MODE, WP_MUST_INDEX, LOG_LASTFILE, AXIS_P
2012-12-10 21:45:57 +09:00
rmackay9
56ceb230cb
ArduCopter: add YAW_OVR_BEHAVE to allow control of when autopilot takes back control of yaw after pilot overrides it during a mission
2012-12-09 18:04:31 +09:00
rmackay9
9dd978576b
ArduCopter: auto yaw changes to allow pilot override of yaw during missions
...
Added set_yaw_mode to better control of yaw controller changes and variable initialisation.
Replaced AUTO_YAW mode with separate yaw controllers YAW_LOOK_AT_NEXT_WP, YAW_LOOK_AT_LOCATION, YAW_LOOK_AT_HEADING.
Pilot manual override of yaw causes yaw to change to YAW_HOLD (i.e. manual yaw) until next waypoint is reached.
Added get_yaw_slew function to control how quickly autopilot turns copter
Changed YAW_LOOK_AHEAD to use GPS heading and moved to new get_look_ahead_yaw function in Attitude.pde
Renamed variables: target_bearing->wp_bearing, original_target_bearing->original_wp_bearing.
Removed auto_yaw_tracking and auto_yaw variables and update_auto_yaw function as they are no longer needed.
Simplified MAV_CMD_CONDITION_YAW handling (do_yaw). We lose ability to control direction of turn and ability to do long panorama shots but it now works between waypoints and save 20bytes.
2012-12-08 14:23:32 +09:00
rmackay9
4ca27defb3
ArduCopter: update comments related to CH7 switch options
2012-12-06 17:40:36 +09:00
rmackay9
39d524212f
ArduCopter: allow accel based throttle controller to be enabled/disabled with the new THR_ACC_ENABLE parameter.
...
When disabled the original velocity based throttle controller is used.
2012-12-06 10:31:57 +09:00
rmackay9
a5bb54e36e
ArduCopter: RTL clean-up and slightly improved landing sensor
...
Consolidated RTL state to be captured by rtl_state variable.
Combined update_RTL_Nav and verify_RTL functions which performed the same function but one was for missions, the other for the RTL flight mode.
Renamed some RTL parameters and global variables to have RTL at the front.
Landing detector now checks accel-throttle's I term and/or a very low throttle value
2012-12-06 10:31:52 +09:00
rmackay9
072ffec493
ArduCopter: allow INERTIAL_NAV to be enabled separately for horizontal and vertical position
2012-12-06 10:31:41 +09:00
rmackay9
7b4ed2d227
ArduCopter: restored landing detector to landing throttle mode.
...
Added LAND_SPEED parameter to control the rate of descent for the last 10m of a landing.
Added CH6 tuning for accel based throttle controller.
2012-12-06 10:31:20 +09:00
rmackay9
3cbef57c64
ArduCopter: first merge of leonard's accel based altitude controller plus other changes from Randy
...
Changes include:
New low-level get_throttle_accel function takes target acceleration and compares vs earth-frame Z accelerometer values to produce output to motors.
Higher level throttle controllers modified to call new get_throttle_accel controller
Throttle_rate_stabilized controller added which maintains a desired climb/descent rate
Throttle_land controller added - descends using normal auto throttle controller to 10m then descends at 50cm/s
Multiple throttle modes added including landing mode
Land flight mode no longer needs GPS
Throttle cruise maintenance moved to update_throttle_cruise function
2012-12-06 10:30:49 +09:00
Robert Lefebvre
5723021be1
ACM: TradHeli
...
Creating Rate Feed-Forward Parameters
2012-12-04 13:47:38 -05:00
Andrew Tridgell
cd07d965a7
Copter: ported RSSI_PIN option from ArduPlane
...
this is useful for OSD users
2012-11-22 20:59:33 +11:00
Andrew Tridgell
bcae83c4f6
ACM: make it possible to run CLI on radio port in ArduCopter
2012-11-21 21:41:34 +11:00
Michael Oborne
0c84b8abf1
fix unit max. and unit type
2012-11-21 07:42:53 +08:00
Andrew Tridgell
c008ca7560
ACM: fixed documentation of disabling voltage/current pins for ArduCopter
2012-11-20 20:26:14 +11:00
rmackay9
e92b560df5
ArduCopter: low baterry failsafe
2012-11-15 23:35:41 +09:00
Jason Short
d2a5928c06
Ap state updates
2012-11-09 22:15:15 -08:00
rmackay9
b13264c884
AP_InertialNav: reanme AP_InertialNav and ThirdOrderCompFilter classes to resolve desktop build compiler errors
2012-11-07 22:24:00 +09:00
rmackay9
1f801714e8
ArduCopter: incorporate new version of inertial navigation
...
Moved several navigation functions from ArduCopter.pde to navigation.pde
2012-11-07 19:21:31 +09:00
rmackay9
a1b4ec6d0e
ArduCopter: move to use new INS library instead of IMU library
2012-11-07 19:21:09 +09:00
rmackay9
5e8043fd9c
ArduCopter: changed ACRO_ROLL_STABILIZE and ACRO_PITCH_STABILIZE to parameters
...
Changes on behalf of Leonard Hall
2012-10-23 21:30:50 +09:00
Jason Short
a0752dc7dc
ACM Acceleration management
...
removed unused waypoint_radius var
removed slow_wp
updated speed management system to maintain a constant acceleration or deceleration of 1m/s
changed version to 2.8.1a
2012-10-21 14:32:39 -07:00
Robert Lefebvre
063cb41a11
Adding some comments to parameters.
2012-10-15 09:37:02 -04:00
rmackay9
240b0b43fd
ArduCopter: small comment fixes related to battery monitoring
2012-10-13 20:52:14 +09:00
rmackay9
4a41a3d210
ArduCopter: added BATT_VOLT_PIN and BATT_CURR_PIN parameters to allow support for new 3DR IV battery voltage and current monitor
2012-10-13 18:40:46 +09:00
Robert Lefebvre
dae81d2068
Added #define for Tilt_Compensation.
...
Also added some detail to WP_Speed_Max parameter.
2012-10-12 14:51:31 -04:00
Robert Lefebvre
4e649a381c
Added comment detail for Tilt_Comp Parameter.
...
Reduced parameter default value for TradHeli.
2012-10-11 13:17:39 -04:00
rmackay9
ea4f256f8e
ArduCopter: BATT_PIN parameter added to allow you to select which pin is used for voltage and current measurements
...
To save a parameter, the current sensor pin is assumed to always be 1 higher than the voltage pin.
2012-10-02 22:16:19 +09:00
rmackay9
95763e610b
ArduCopter: allow DMP to run in parallel with DCM
...
Parallel DMP can be enabled by #define SECONDARY_DMP_ENABLED in APM_Config.h
New DMP dataflash log type added to allow easy comparison with DCM
2012-09-30 00:25:40 +09:00
Michael Oborne
c1235c55d5
Fix Approach Altitude min
2012-09-06 17:43:58 +08:00
rmackay9
c9d34c1737
ArduCopter: fixes to allow AP_Mount to work on APM1 with original default channels and fix to reenable support for 3-axis gimbals on APM2.
...
Channels 5 to 11 changed to RC_Channel_aux.
Removed channel 9 because APM_RC doesn't support it in any case.
Updated EEPROM format version to 119 because of the change to RC_Channel_aux and because k_param_rc_11 moved to be after k_param_rc_10.
2012-09-02 12:51:23 +09:00
Andrew Tridgell
e8d928cca4
ACM: added TELEM_DELAY to ArduCopter
2012-08-30 09:03:01 +10:00
uncrustify
2438cd32fc
uncrustify ArduCopter/Parameters.pde
2012-08-21 19:19:50 -07:00
Andrew Tridgell
bf2319a0fc
AHRS: fixed reference to AHRS var_info for APM and ACM
2012-08-21 15:58:32 +10:00
Michael Oborne
b2b73cc6cb
AC fix some Parameter units
2012-08-18 08:30:16 +08:00
rmackay9
36f947acb9
ArduCopter: changed all "int" to "int16_t" and a few "long"s to "int32_t".
...
Also moved "simple_counter" variable from global scope to the "update_simple_mode" function which is the only place that it's actually used.
2012-08-16 20:04:46 +09:00
rmackay9
2a83f1eef2
ArduCopter: remove RTL_LAND parameter as it's been deprecated in favour of APPROACH_ALT.
...
Updated comments on ALT_HOLD_RTL and APPROACH_ALT to make it a little easier to understand.
2012-08-14 12:14:35 +09:00
Andrew Tridgell
3bdc7d41be
INS: disable INS AP_Param table when not on APM1 hardware
...
this could cause overwriting of memory with default values
2012-08-11 22:06:03 +10:00
Andrew Tridgell
c2dc920d02
ACM: allow users to set the AHRS_YAW_P and AHRS_RP_P
...
the forced set left users with parameters they couldn't use
2012-08-11 08:35:10 +10:00
Amilcar Lucas
d34549f386
Add an optional second mount to ArduPlane and ArduCopter
2012-08-08 23:22:24 +02:00
Amilcar Lucas
9cc705939a
Add a second mount instance
2012-08-08 23:07:25 +02:00
Andrew Tridgell
03714fc695
ACM: make it possible to set AHRS_GPS_GAIN on ArduCopter
...
this was affected by the AP_Param change, in particular the
constructor ordering. To ensure a user can set AHRS_GPS_GAIN to 1.0 if
they want to, we need to do a set_and_save() if the value isn't in
EEPROM
2012-08-08 17:36:01 +10:00
Andrew Tridgell
c2a4d59132
AP_Param: update ArduCopter core for new AP_Param interface
2012-08-08 12:11:57 +10:00
Amilcar Lucas
d9f1140278
ArduCopter: Use generic channel names for AP_Mount servos.
...
This simplifies mission planner, the same code can be used for plane and copter now.
2012-08-06 23:33:51 +02:00
rmackay9
a5b5f6a619
ArduCopter: bug fix to global var_info parameter list for ahrs object.
2012-08-01 10:52:27 +09:00
rmackay9
f97257830b
ArduCopter: changes in arducopter to support moving AHRS var_info from AP_AHRS to AP_AHRS_DCM
2012-07-28 14:18:31 +09:00
Jason Short
c9d3ab5413
Oilpan ADC parameters added
...
including a function that configures each Accel Axis
Defaults matching old behavior
Added param group
2012-07-18 22:57:11 -07:00
Michael Oborne
636fcadde4
fix rc libray param gen
2012-07-18 07:03:39 +08:00
Andreas M. Antonopoulos
0e5345d17b
AP_Limits: documentation bug (which uncovered a param_parser bug - the irony burns)
2012-07-16 23:35:11 -07:00
Michael Oborne
e632ad6aa4
AC fix limits param gen header
2012-07-15 18:23:06 +08:00
rmackay9
29b6ec0b11
ArduCopter: reverted channel 5~8 to be regular RC_Channel objects, restored rc_camera_roll and rc_camera_pitch RC_Channels and created new rc_camera_yaw RC_Channel to control the camera mount servos.
...
Defined camera_mount (MNT_) in Parameters.h and Parameters.pde so that it appears in global parameters list.
Removed unused camera_*_gain and camaera_*_continuous parameters.
2012-07-15 16:36:05 +09:00