// @Description: When enabled, after an autoland and auto-disarm via LAND_DISARMDELAY happens then set all servos to neutral. This is helpful when an aircraft has a rough landing upside down or a crazy angle causing the servos to strain.
Reverse thrust for controlled landings, even with much steeper approach slopes. This is achieved by allowing throttle demand to go negative to maintain a target airspeed. A Pre-Flare stage was added, triggered by an altitude, to allow for a slower airspeed just before land. That lower airspeed can be near stall.
new params LAND_PF_ALT, LAND_PF_SEC, LAND_PF_ARSPD, USE_REV_THRUST
@Description: X-Axis deceleration threshold to notify the crash detector that there was a possible impact which helps disarm the motor quickly after a crash. This value should be much higher than normal negative x-axis forces during normal flight, check flight log files to determine the average IMU.x values for your aircraft and motor type. Higher value means less sensative (triggers on higher impact). For electric planes that don't vibrate much during fight a value of 25 is good (that's about 2.5G). For petrol/nitro planes you'll want a higher value. Set to 0 to disable the collision detector.
- parse MAVLINK_MSG_ADSB_VEHICLE msg
- new 1Hz adsb_update task to compare list against for threat detection
- perform object avoidance via loiter or loiter_and_descend. More methods are welcome!
Now variables don't have to be declared with PROGMEM anymore, so remove
them. This was automated with:
git grep -l -z PROGMEM | xargs -0 sed -i 's/ PROGMEM / /g'
git grep -l -z PROGMEM | xargs -0 sed -i 's/PROGMEM//g'
The 2 commands were done so we don't leave behind spurious spaces.
AVR-specific places were not changed.
The PSTR is already define as a NOP for all supported platforms. It's
only needed for AVR so here we remove all the uses throughout the
codebase.
This was automated with a simple python script so it also converts
places which spans to multiple lines, removing the matching parentheses.
AVR-specific places were not changed.
- enabled via new param LAND_ABORT_THR default is 0 (disabled)
- Triggered via 95% throttle during landing, a landing abort will take place.
- This copies all takeoff params for right now, we can make this better later if needed
- added mission item command to NAV_LAND which is the abort takeoff altitude. If 0 then use last takeoff if available, else use 30m
- hold heading, just like takeoff, until altitude is reached
- pitch is constrained to takeoff pitch, or else 10deg if not available
- After abort altitude is reached, the normal landing restart happens (DO_LAND_START or decrement mission)
- restart landing by jumping to DO_LAND_START or decrement mission on mode change
* Retains ability to read from Analog Pin
* Adds ability to read RSSI from PWM channel value as is done in OpenLRSng, EazyUHF, and various other LRS.
* Handles any type of RSSI that provides RSSI values inverted - i.e. when the low value is the best signal and the high value is the worst signal.
* Has different key names from all existing RSSI parameters to provide for a clean break and easier distinguishing.
* Existing parameters are marked as obsolete
add crash detection, allow disengage via param CRASH_DETECT
improved is_flying behavior
take off, landing and hard-landing improvements
add stillness check to is_flying and log it
minimum airspeed is determined ARSPD_FBW_MIN*0.75
Andrew Tridgell
Lucas De Marchi
Don Gagne
Tom Pittenger
squilter
pepevalbe
Peter Barker
Andre Kjellstrup
Caio Marcelo de Oliveira Filho
Randy Mackay
Grant Morphett
Stewart Loving-Gibbard
Michael Oborne