3e905ec750
Ap state updates
2012-11-09 22:15:15 -08:00
af40201b14
ArduCopter: incorporate new version of inertial navigation
...
Moved several navigation functions from ArduCopter.pde to navigation.pde
2012-11-07 19:21:31 +09:00
e2b1cb7e8d
AP_InertialSensor: changes after review with Tridge.
...
sanity checking added to accelerometer calibration routine.
user feedback is sent using gcs_send_text_fmt instead of Serial.printf.
moved ins parameters to new eeprom number to avoid conflicts with older parameters.
other small changes including renaming of functions and parameters.
2012-11-07 19:21:15 +09:00
0868917ff4
ArduCopter: move to use new INS library instead of IMU library
2012-11-07 19:21:09 +09:00
ab86eae860
ArduCopter: changed ACRO_ROLL_STABILIZE and ACRO_PITCH_STABILIZE to parameters
...
Changes on behalf of Leonard Hall
2012-10-23 21:30:50 +09:00
4c7292e6ce
ArduCopter: incremented eeprom format version to force users to accept the new defaults.
...
Particularly important is the roll-pitch I term move from the stabilize to rate controllers.
2012-10-19 16:14:51 +09:00
71c773801a
ArduCopter: added BATT_VOLT_PIN and BATT_CURR_PIN parameters to allow support for new 3DR IV battery voltage and current monitor
2012-10-13 18:40:46 +09:00
770aa0b56b
ArduCopter: BATT_PIN parameter added to allow you to select which pin is used for voltage and current measurements
...
To save a parameter, the current sensor pin is assumed to always be 1 higher than the voltage pin.
2012-10-02 22:16:19 +09:00
2fcc7d3b22
ACM : Params - formatting cleanup
2012-09-10 20:22:11 -07:00
3e6966c33d
ArduCopter: fixes to allow AP_Mount to work on APM1 with original default channels and fix to reenable support for 3-axis gimbals on APM2.
...
Channels 5 to 11 changed to RC_Channel_aux.
Removed channel 9 because APM_RC doesn't support it in any case.
Updated EEPROM format version to 119 because of the change to RC_Channel_aux and because k_param_rc_11 moved to be after k_param_rc_10.
2012-09-02 12:51:23 +09:00
0b2cbbb677
ACM: added TELEM_DELAY to ArduCopter
2012-08-30 09:03:01 +10:00
5dceeed7ce
uncrustify ArduCopter/Parameters.h
2012-08-21 18:57:21 -07:00
95c59fd4a4
ArduCopter: remove RTL_LAND parameter as it's been deprecated in favour of APPROACH_ALT.
...
Updated comments on ALT_HOLD_RTL and APPROACH_ALT to make it a little easier to understand.
2012-08-14 12:14:35 +09:00
f321f5d9c5
Add a second mount instance
2012-08-08 23:07:25 +02:00
d8106cf20f
AP_Param: update ArduCopter core for new AP_Param interface
2012-08-08 12:11:57 +10:00
ff32fed176
ArduCopter: Use generic channel names for AP_Mount servos.
...
This simplifies mission planner, the same code can be used for plane and copter now.
2012-08-06 23:33:51 +02:00
16dd919819
Fix heli compilation
2012-08-06 23:30:02 +02:00
fe4713b46e
RC_Channel: Allow each channel to know who they are, this simplifies the enabling and output function calls.
2012-08-05 23:08:31 +02:00
24d05c171a
Arducopter: Renamed Config define (RTL_HOLD_ALT)
2012-07-19 17:50:15 -07:00
243aa72abe
Arducopters parameter: Adjusted RTL_ALTITUDE units so they reflect comments in config.h
2012-07-19 09:50:57 -07:00
25c3ed6c4b
Oilpan ADC parameters added
...
including a function that configures each Accel Axis
Defaults matching old behavior
Added param group
2012-07-18 22:57:11 -07:00
0dc0e3801c
ArduCopter: reverted channel 5~8 to be regular RC_Channel objects, restored rc_camera_roll and rc_camera_pitch RC_Channels and created new rc_camera_yaw RC_Channel to control the camera mount servos.
...
Defined camera_mount (MNT_) in Parameters.h and Parameters.pde so that it appears in global parameters list.
Removed unused camera_*_gain and camaera_*_continuous parameters.
2012-07-15 16:36:05 +09:00
31fd74d94c
AP_Limits library, provides modular "limits" such as altitude and geo-fencing.
2012-07-14 19:26:17 -07:00
9dfb3c4db9
Added Michael Pursifull's Maxsonar HRLV model support
2012-07-11 18:46:47 -07:00
32e6a6ba8d
Arducopter:Params
...
WP_RADIUS_DEFAULT is now stored the same as Arduplane
2012-07-10 21:53:37 -07:00
492809098b
Toy Mode: High Yaw default
2012-07-10 21:53:37 -07:00
8e14ebbc10
Merge the changes from APM_Camera branch into ArduCopter
...
Conflicts:
ArduCopter/Camera.pde
ArduCopter/Parameters.pde
2012-07-11 00:39:13 +02:00
9e796899e4
Airspeed patch:
...
pre-calculated airspeed resistance pitches copter automatically to gain a certain speed allowing the speed controller to work off of a better set point - similar to Alt hold.
added param tilt_comp with a default of 54 which equals 19.5° of pitch to go 6m/s
upped Z and Y target speeds to int32_t for speed squared calculation
2012-07-09 13:13:32 -07:00
278e215a21
Parameters: Added flag for camera pitch/roll servos (continuous or regular)
2012-07-04 21:06:21 -05:00
69fe7feb54
Params
...
Added Tilt_Compensation to Params,
deprecated RTL_Land_Enabeled
RTL_Approach_alt is not int16_t, -1 means do noting. 0 means land, >1 means hover to that altitude after timeout.
2012-07-03 17:33:03 -07:00
44e12c6d2d
Parameters
...
removed unused parameters for retro loiter
2012-07-01 13:40:12 -07:00
eb06320559
Params: Added toy_yate_rate
2012-06-29 21:20:27 -07:00
1cb96e14a9
SITL: enable the SIM_* parameters in ArduCopter and ArduPlane
2012-06-29 15:10:52 +10:00
95f3041d25
Parameters.h: throttle_min and throttle_max now have defaults from Config.h
2012-06-20 15:02:00 -07:00
f2edc87797
Added note to remove this unused param
2012-06-03 11:13:50 -07:00
996cfc5c96
changed WP radius to AP_Int16
2012-05-28 22:39:29 -07:00
a9349a6e87
More CopterLEDS changes.
...
Merged CopterLEDS and Piezo functions to eliminate pin conflict on APM2. Created new Parameter bit to turn piezo function on and off from MP. Moved GPS and Aux pin assignments to allow commonality between APM1 and 2. Set LED_Mode parameter default to 9 in order to make CopterLEDS completely backwards compatible with old Motor LEDS and Piezo code. Legacy users should see no difference.
2012-05-15 12:00:21 -04:00
ec06638db6
Parameters: Added g.retro_loiter which is configurable by the user via the MP.
2012-04-23 00:17:52 -05:00
8128fb2d5f
Merge branch 'master' of https://code.google.com/p/ardupilot-mega into auto-approach
...
Conflicts:
ArduCopter/Parameters.h
2012-04-16 10:23:01 -05:00
2d096c401f
Parameters: Changed rtl_approach_alt to float to support more granular altitudes
2012-04-16 10:06:29 -05:00
5a9ad6ddbb
AHRS: enable AHRS_ group in ArduCopter
2012-04-16 20:55:14 +10:00
f5e0b002ba
Parameters: Added new APPROACH_ALT params (g.rtl_approach_alt) which stored the users desired target altitude after RTL is complete.
2012-04-15 16:51:41 -05:00
d1a5d1f94c
ArduCopter - LEDS - two new parameters to support COPTER_LEDS.
...
Code by Robert Lefebvre.
2012-04-12 22:55:28 +09:00
023378a214
ArduCopter - Parameters.h - changed initialisation order to remove compiler warning (have not changed enum values so shouldn't require eeprom format id update)
2012-04-09 17:37:06 +09:00
929e933b69
ArduCopter - increased firmware version to 118. Removed nearly all heli parameters as these are all created by the AP_MotorHeli class now.
...
Note: we cannot move the heli_servos to the AP_MotorHeli class yet because of a small issue in the parameters class.
2012-04-04 22:55:07 +09:00
a7e0fc7774
Added support for TradHeli H1 swashplate type. Added new param heli_h1_swash_enabled.
...
Signed-off-by: Robert Lefebvre <robert.lefebvre@gmail.com>
2012-03-03 08:14:14 -05:00
bfca928211
ACM: added RC_SPEED MAVLink parameter
...
this will set the speed for APM_RC.SetFastOutputChannels()
2012-03-02 17:57:08 +11:00
1e2b57410c
ACM: fixed Parameters.h to avoid duplicate keys
...
unfortunately everyone needs to reload
2012-03-02 15:48:28 +11:00
6ca8aeecf3
added stab_d gain scheduling
2012-02-28 20:16:40 -08:00
83ad721b73
added Axis_Lock params
2012-02-18 21:13:06 -08:00
Jason Short
rmackay9
Andrew Tridgell
uncrustify
Amilcar Lucas
Andreas M. Antonopoulos
Adam M Rivera
Robert Lefebvre