If the GPS receiver selection changes and we are using GPS for height, the
vertical position will be reset to the new GPS height measurement.
correct output observer history when doing a GPS height reset
Fixes a bug that allows the last reported reset time to to wind back and an out of date reset delta to be reported if a switch to a core that has previously been reset occurs.
Allows multiple consumers provided they access on the same frame.
Fixes a bug that allows the last reported reset time to to wind back and an out of date reset delta to be reported if a switch to a core that has previously been reset occurs.
Allows multiple consumers provided they access on the same frame.
Fixes a bug that allows the last reported reset time to to wind back and an out of date reset delta to be reported if a switch to a core that has previously been reset occurs.
Allows multiple consumers provided they access on the same frame
1) Do not switch to a core until its states have been updated.
2) Distinguish between mandated switches required for health failure and optional switches required due to innovation checks failing.
3) Apply hyseresis to innovation check levels
RC_Channel: To nullptr from NULL.
AC_Fence: To nullptr from NULL.
AC_Avoidance: To nullptr from NULL.
AC_PrecLand: To nullptr from NULL.
DataFlash: To nullptr from NULL.
SITL: To nullptr from NULL.
GCS_MAVLink: To nullptr from NULL.
DataFlash: To nullptr from NULL.
AP_Compass: To nullptr from NULL.
Global: To nullptr from NULL.
Global: To nullptr from NULL.
This can improve position hold performance where it is not practical to have the IMU located at the centroid.
Although this enables the effect of IMU position offsets to be corrected, users will still need to be instructed to place the IMU as close to the vehicle c.g. as practical as correcting for large offsets makes the velocity estimates noisy.
Correction requires the body rates averaged across the flow sensor sampling interval. This data has been added to the sensor buffer.
The body rate data from the flow sensor driver does not contain the Z component, so an equivalent value sampled from the navigation IMU has been used instead.
The variable omegaAcrossFlowTime has been moved out of the class and into the only function that uses it.
A specialised takeoff check is now always performed when we receive new flow data as the default behaviour is to try and use flow data whenever it is received, rather than limit its use to a use to a flow-only mode of operation that had to be selected via user parameter.
Enables simultaneous use of GPS and optical flow data with automatic fallback to relative position mode if GPS is lost and automatic switch-up to absolute position status if GPS gained/re-gained.
Revert "AP_NavEKF2: Fix bug in published yaw reset value found during code review"
commit 175faf1e41.
Revert "AP_NavEKF2: use a struct for all yaw step class variables"
commit 77fad065d1.
Partially revert "AP_NavEKF2: Handle yaw jumps due to core switches"
commit 885bfd1b4e.
The EK2_RNG_USE_HGT parameter sets the height (expressed as a percentage of the maximum range of the range finder as set by the RNGFND_MAX_CM parameter) below which the range finder will be used as the primary height source when the vehicle is moving slowly.
When using a height reference other than GPS, the height datum can drift due to air pressure changes if using baro, or due to terrain height changes if using range finder as the primary height source. To ensure that a consistent height datum is available when switching between altitude sources, the WGS-84 height estimate of the EKF's local positi norigin is updated using a
single state Bayes estimator,
If rngfinder or gps height data is lost whilst being used, there will be a fall-back to baro data.
When switching over to a back up magnetometer, ensure that the earth field estimate are reset. other wise mag earth field estimates due to the previous failed mag could cause data from the new mag to be rejected.
This bug created a race condition whereby if the EKF had to reset the yaw to the GPS ground course to recover from a bad magnetometer, the new heading could be over-written by the bad magnetic heading when the plane reached the height for the scheduled reset.
If the GPS receiver was disconnected and no data received, then then the gpsGoodToAlign check did not get a chance to run and becasue it was previously true the EKF would switch back into aiding.
This prevents this by ensuring that gpsGoodToAlign defaults to false when the check is not being performed.
An additional check has also been dded to ensure that there is GPS data to fuse before we declare ready to use GPS.
Switching in and out of aiding modes was being performed in more than one place and was using two variables.
The reversion out of GPS mode due to prolonged loss of GPS was not working.
This consolidates the logic and ensures that PV_AidingMode is only changed by the setAidingMode function.
priseborough
Andrew Tridgell
Randy Mackay
Jonathan Challinger
Jacob Walser
Michael du Breuil
Dr.-Ing. Amilcar Do Carmo Lucas
Francisco Ferreira
murata
Mathieu OTHACEHE