ardupilot/ArduPlane/altitude.cpp

773 lines
26 KiB
C++
Raw Normal View History

/*
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
2015-05-13 03:09:36 -03:00
#include "Plane.h"
/*
altitude handling routines. These cope with both barometric control
and terrain following control
*/
/*
adjust altitude target depending on mode
*/
2015-05-13 03:09:36 -03:00
void Plane::adjust_altitude_target()
{
2017-02-14 15:13:11 -04:00
Location target_location;
if (control_mode == &mode_fbwb ||
control_mode == &mode_cruise) {
return;
}
#if OFFBOARD_GUIDED == ENABLED
if (control_mode == &mode_guided && ((guided_state.target_alt_time_ms != 0) || guided_state.target_alt > -0.001 )) { // target_alt now defaults to -1, and _time_ms defaults to zero.
// offboard altitude demanded
uint32_t now = AP_HAL::millis();
float delta = 1e-3f * (now - guided_state.target_alt_time_ms);
guided_state.target_alt_time_ms = now;
// determine delta accurately as a float
float delta_amt_f = delta * guided_state.target_alt_accel;
// then scale x100 to match last_target_alt and convert to a signed int32_t as it may be negative
int32_t delta_amt_i = (int32_t)(100.0 * delta_amt_f);
Location temp {};
temp.alt = guided_state.last_target_alt + delta_amt_i; // ...to avoid floats here,
if (is_positive(guided_state.target_alt_accel)) {
temp.alt = MIN(guided_state.target_alt, temp.alt);
} else {
temp.alt = MAX(guided_state.target_alt, temp.alt);
}
guided_state.last_target_alt = temp.alt;
set_target_altitude_location(temp);
} else
#endif // OFFBOARD_GUIDED == ENABLED
if (control_mode->update_target_altitude()) {
// handled in mode specific code
} else if (landing.is_flaring()) {
// during a landing flare, use TECS_LAND_SINK as a target sink
// rate, and ignores the target altitude
set_target_altitude_location(next_WP_loc);
} else if (landing.is_on_approach()) {
landing.setup_landing_glide_slope(prev_WP_loc, next_WP_loc, current_loc, target_altitude.offset_cm);
landing.adjust_landing_slope_for_rangefinder_bump(rangefinder_state, prev_WP_loc, next_WP_loc, current_loc, auto_state.wp_distance, target_altitude.offset_cm);
2017-02-14 15:13:11 -04:00
} else if (landing.get_target_altitude_location(target_location)) {
set_target_altitude_location(target_location);
#if HAL_SOARING_ENABLED
} else if (g2.soaring_controller.is_active() && g2.soaring_controller.get_throttle_suppressed()) {
// Reset target alt to current alt, to prevent large altitude errors when gliding.
set_target_altitude_location(current_loc);
reset_offset_altitude();
#endif
} else if (reached_loiter_target()) {
// once we reach a loiter target then lock to the final
// altitude target
set_target_altitude_location(next_WP_loc);
} else if (target_altitude.offset_cm != 0 &&
!current_loc.past_interval_finish_line(prev_WP_loc, next_WP_loc)) {
// control climb/descent rate
set_target_altitude_proportion(next_WP_loc, 1.0f-auto_state.wp_proportion);
// stay within the range of the start and end locations in altitude
constrain_target_altitude_location(next_WP_loc, prev_WP_loc);
} else {
set_target_altitude_location(next_WP_loc);
}
altitude_error_cm = calc_altitude_error_cm();
}
/*
setup for a gradual glide slope to the next waypoint, if appropriate
*/
2015-05-13 03:09:36 -03:00
void Plane::setup_glide_slope(void)
{
// establish the distance we are travelling to the next waypoint,
// for calculating out rate of change of altitude
auto_state.wp_distance = current_loc.get_distance(next_WP_loc);
auto_state.wp_proportion = current_loc.line_path_proportion(prev_WP_loc, next_WP_loc);
2016-01-08 20:12:03 -04:00
SpdHgt_Controller->set_path_proportion(auto_state.wp_proportion);
update_flight_stage();
/*
work out if we will gradually change altitude, or try to get to
the new altitude as quickly as possible.
*/
switch (control_mode->mode_number()) {
case Mode::Number::RTL:
case Mode::Number::AVOID_ADSB:
case Mode::Number::GUIDED:
/* glide down slowly if above target altitude, but ascend more
rapidly if below it. See
2016-03-25 06:47:03 -03:00
https://github.com/ArduPilot/ardupilot/issues/39
*/
if (above_location_current(next_WP_loc)) {
set_offset_altitude_location(next_WP_loc);
} else {
reset_offset_altitude();
}
break;
case Mode::Number::AUTO:
// we only do glide slide handling in AUTO when above 20m or
// when descending. The 20 meter threshold is arbitrary, and
// is basically to prevent situations where we try to slowly
// gain height at low altitudes, potentially hitting
// obstacles.
if (adjusted_relative_altitude_cm() > 2000 || above_location_current(next_WP_loc)) {
set_offset_altitude_location(next_WP_loc);
} else {
reset_offset_altitude();
}
break;
default:
reset_offset_altitude();
break;
}
}
/*
return RTL altitude as AMSL cm
*/
int32_t Plane::get_RTL_altitude_cm() const
{
if (g.RTL_altitude_cm < 0) {
return current_loc.alt;
}
return g.RTL_altitude_cm + home.alt;
}
/*
return relative altitude in meters (relative to terrain, if available,
or home otherwise)
*/
float Plane::relative_ground_altitude(bool use_rangefinder_if_available)
{
if (use_rangefinder_if_available && rangefinder_state.in_range) {
return rangefinder_state.height_estimate;
}
if (use_rangefinder_if_available && quadplane.in_vtol_land_final() &&
rangefinder.status_orient(ROTATION_PITCH_270) == RangeFinder::Status::OutOfRangeLow) {
// a special case for quadplane landing when rangefinder goes
// below minimum. Consider our height above ground to be zero
return 0;
}
#if AP_TERRAIN_AVAILABLE
float altitude;
if (target_altitude.terrain_following &&
terrain.status() == AP_Terrain::TerrainStatusOK &&
terrain.height_above_terrain(altitude, true)) {
return altitude;
}
#endif
if (quadplane.in_vtol_land_descent() &&
!(quadplane.options & QuadPlane::OPTION_MISSION_LAND_FW_APPROACH)) {
// when doing a VTOL landing we can use the waypoint height as
// ground height. We can't do this if using the
// LAND_FW_APPROACH as that uses the wp height as the approach
// height
return height_above_target();
}
return relative_altitude;
}
/*
set the target altitude to the current altitude. This is used when
setting up for altitude hold, such as when releasing elevator in
CRUISE mode.
*/
2015-05-13 03:09:36 -03:00
void Plane::set_target_altitude_current(void)
{
// record altitude above sea level at the current time as our
// target altitude
target_altitude.amsl_cm = current_loc.alt;
// reset any glide slope offset
reset_offset_altitude();
#if AP_TERRAIN_AVAILABLE
// also record the terrain altitude if possible
float terrain_altitude;
if (terrain_enabled_in_current_mode() && terrain.height_above_terrain(terrain_altitude, true) && !terrain_disabled()) {
target_altitude.terrain_following = true;
target_altitude.terrain_alt_cm = terrain_altitude*100;
} else {
// if terrain following is disabled, or we don't know our
// terrain altitude when we set the altitude then don't
// terrain follow
target_altitude.terrain_following = false;
}
#endif
}
/*
set the target altitude to the current altitude, with ALT_OFFSET adjustment
*/
2015-05-13 03:09:36 -03:00
void Plane::set_target_altitude_current_adjusted(void)
{
set_target_altitude_current();
// use adjusted_altitude_cm() to take account of ALTITUDE_OFFSET
target_altitude.amsl_cm = adjusted_altitude_cm();
}
/*
set target altitude based on a location structure
*/
2015-05-13 03:09:36 -03:00
void Plane::set_target_altitude_location(const Location &loc)
{
target_altitude.amsl_cm = loc.alt;
if (loc.relative_alt) {
target_altitude.amsl_cm += home.alt;
}
#if AP_TERRAIN_AVAILABLE
/*
if this location has the terrain_alt flag set and we know the
terrain altitude of our current location then treat it as a
terrain altitude
*/
float height;
if (loc.terrain_alt && terrain.height_above_terrain(height, true)) {
target_altitude.terrain_following = true;
target_altitude.terrain_alt_cm = loc.alt;
if (!loc.relative_alt) {
// it has home added, remove it
target_altitude.terrain_alt_cm -= home.alt;
}
} else {
target_altitude.terrain_following = false;
}
#endif
}
/*
return relative to home target altitude in centimeters. Used for
altitude control libraries
*/
2015-05-13 03:09:36 -03:00
int32_t Plane::relative_target_altitude_cm(void)
{
#if AP_TERRAIN_AVAILABLE
float relative_home_height;
if (target_altitude.terrain_following &&
terrain.height_relative_home_equivalent(target_altitude.terrain_alt_cm*0.01f,
relative_home_height, true)) {
// add lookahead adjustment the target altitude
target_altitude.lookahead = lookahead_adjustment();
relative_home_height += target_altitude.lookahead;
// correct for rangefinder data
relative_home_height += rangefinder_correction();
// we are following terrain, and have terrain data for the
// current location. Use it.
return relative_home_height*100;
}
#endif
int32_t relative_alt = target_altitude.amsl_cm - home.alt;
relative_alt += mission_alt_offset()*100;
relative_alt += rangefinder_correction() * 100;
return relative_alt;
}
/*
change the current target altitude by an amount in centimeters. Used
to cope with changes due to elevator in CRUISE or FBWB
*/
2015-05-13 03:09:36 -03:00
void Plane::change_target_altitude(int32_t change_cm)
{
target_altitude.amsl_cm += change_cm;
#if AP_TERRAIN_AVAILABLE
if (target_altitude.terrain_following && !terrain_disabled()) {
target_altitude.terrain_alt_cm += change_cm;
}
#endif
}
/*
change target altitude by a proportion of the target altitude offset
(difference in height to next WP from previous WP). proportion
should be between 0 and 1.
When proportion is zero we have reached the destination. When
proportion is 1 we are at the starting waypoint.
Note that target_altitude is setup initially based on the
destination waypoint
*/
2015-05-13 03:09:36 -03:00
void Plane::set_target_altitude_proportion(const Location &loc, float proportion)
{
set_target_altitude_location(loc);
proportion = constrain_float(proportion, 0.0f, 1.0f);
change_target_altitude(-target_altitude.offset_cm*proportion);
//rebuild the glide slope if we are above it and supposed to be climbing
if(g.glide_slope_threshold > 0) {
if(target_altitude.offset_cm > 0 && calc_altitude_error_cm() < -100 * g.glide_slope_threshold) {
set_target_altitude_location(loc);
set_offset_altitude_location(loc);
change_target_altitude(-target_altitude.offset_cm*proportion);
//adjust the new target offset altitude to reflect that we are partially already done
if(proportion > 0.0f)
target_altitude.offset_cm = ((float)target_altitude.offset_cm)/proportion;
}
}
}
/*
constrain target altitude to be between two locations. Used to
ensure we stay within two waypoints in altitude
*/
2015-05-13 03:09:36 -03:00
void Plane::constrain_target_altitude_location(const Location &loc1, const Location &loc2)
{
if (loc1.alt > loc2.alt) {
target_altitude.amsl_cm = constrain_int32(target_altitude.amsl_cm, loc2.alt, loc1.alt);
} else {
target_altitude.amsl_cm = constrain_int32(target_altitude.amsl_cm, loc1.alt, loc2.alt);
}
}
/*
return error between target altitude and current altitude
*/
2015-05-13 03:09:36 -03:00
int32_t Plane::calc_altitude_error_cm(void)
{
#if AP_TERRAIN_AVAILABLE
float terrain_height;
if (target_altitude.terrain_following &&
terrain.height_above_terrain(terrain_height, true)) {
return target_altitude.lookahead*100 + target_altitude.terrain_alt_cm - (terrain_height*100);
}
#endif
return target_altitude.amsl_cm - adjusted_altitude_cm();
}
/*
check for FBWB_min_altitude_cm violation
*/
void Plane::check_fbwb_minimum_altitude(void)
{
if (g.FBWB_min_altitude_cm == 0) {
return;
}
#if AP_TERRAIN_AVAILABLE
if (target_altitude.terrain_following) {
// set our target terrain height to be at least the min set
if (target_altitude.terrain_alt_cm < g.FBWB_min_altitude_cm) {
target_altitude.terrain_alt_cm = g.FBWB_min_altitude_cm;
}
return;
}
#endif
if (target_altitude.amsl_cm < home.alt + g.FBWB_min_altitude_cm) {
target_altitude.amsl_cm = home.alt + g.FBWB_min_altitude_cm;
}
}
/*
reset the altitude offset used for glide slopes
*/
2015-05-13 03:09:36 -03:00
void Plane::reset_offset_altitude(void)
{
target_altitude.offset_cm = 0;
}
/*
reset the altitude offset used for glide slopes, based on difference
between altitude at a destination and current altitude. If
destination is above the current altitude then the result is
positive.
*/
2015-05-13 03:09:36 -03:00
void Plane::set_offset_altitude_location(const Location &loc)
{
target_altitude.offset_cm = loc.alt - current_loc.alt;
#if AP_TERRAIN_AVAILABLE
2014-07-24 20:07:45 -03:00
/*
if this location has the terrain_alt flag set and we know the
terrain altitude of our current location then treat it as a
terrain altitude
*/
float height;
if (loc.terrain_alt &&
2014-07-24 20:07:45 -03:00
target_altitude.terrain_following &&
terrain.height_above_terrain(height, true)) {
2014-07-24 20:07:45 -03:00
target_altitude.offset_cm = target_altitude.terrain_alt_cm - (height * 100);
}
#endif
if (flight_stage != AP_Vehicle::FixedWing::FLIGHT_LAND) {
// if we are within GLIDE_SLOPE_MIN meters of the target altitude
// then reset the offset to not use a glide slope. This allows for
// more accurate flight of missions where the aircraft may lose or
// gain a bit of altitude near waypoint turn points due to local
// terrain changes
if (g.glide_slope_min <= 0 ||
labs(target_altitude.offset_cm)*0.01f < g.glide_slope_min) {
target_altitude.offset_cm = 0;
}
}
}
/*
return true if current_loc is above loc. Used for glide slope
calculations.
"above" is simple if we are not terrain following, as it just means
the pressure altitude of one is above the other.
When in terrain following mode "above" means the over-the-terrain
current altitude is above the over-the-terrain alt of loc. It is
quite possible for current_loc to be "above" loc when it is at a
lower pressure altitude, if current_loc is in a low part of the
terrain
*/
2015-05-13 03:09:36 -03:00
bool Plane::above_location_current(const Location &loc)
{
#if AP_TERRAIN_AVAILABLE
float terrain_alt;
if (loc.terrain_alt &&
terrain.height_above_terrain(terrain_alt, true)) {
float loc_alt = loc.alt*0.01f;
if (!loc.relative_alt) {
loc_alt -= home.alt*0.01f;
}
return terrain_alt > loc_alt;
}
#endif
float loc_alt_cm = loc.alt;
if (loc.relative_alt) {
loc_alt_cm += home.alt;
}
return current_loc.alt > loc_alt_cm;
}
/*
modify a destination to be setup for terrain following if
TERRAIN_FOLLOW is enabled
*/
void Plane::setup_terrain_target_alt(Location &loc) const
{
2014-07-24 19:02:19 -03:00
#if AP_TERRAIN_AVAILABLE
if (terrain_enabled_in_current_mode()) {
loc.change_alt_frame(Location::AltFrame::ABOVE_TERRAIN);
}
2014-07-24 19:02:19 -03:00
#endif
}
/*
return current_loc.alt adjusted for ALT_OFFSET
This is useful during long flights to account for barometer changes
from the GCS, or to adjust the flying height of a long mission
*/
2015-05-13 03:09:36 -03:00
int32_t Plane::adjusted_altitude_cm(void)
{
return current_loc.alt - (mission_alt_offset()*100);
}
/*
return home-relative altitude adjusted for ALT_OFFSET This is useful
during long flights to account for barometer changes from the GCS,
or to adjust the flying height of a long mission
*/
2015-05-13 03:09:36 -03:00
int32_t Plane::adjusted_relative_altitude_cm(void)
{
return (relative_altitude - mission_alt_offset())*100;
}
/*
return the mission altitude offset. This raises or lowers all
mission items. It is primarily set using the ALT_OFFSET parameter,
but can also be adjusted by the rangefinder landing code for a
NAV_LAND command if we have aborted a steep landing
*/
float Plane::mission_alt_offset(void)
{
float ret = g.alt_offset;
if (control_mode == &mode_auto &&
(flight_stage == AP_Vehicle::FixedWing::FLIGHT_LAND || auto_state.wp_is_land_approach)) {
// when landing after an aborted landing due to too high glide
// slope we use an offset from the last landing attempt
ret += landing.alt_offset;
}
return ret;
}
/*
return the height in meters above the next_WP_loc altitude
*/
2015-05-13 03:09:36 -03:00
float Plane::height_above_target(void)
{
float target_alt = next_WP_loc.alt*0.01;
if (!next_WP_loc.relative_alt) {
target_alt -= ahrs.get_home().alt*0.01f;
}
#if AP_TERRAIN_AVAILABLE
// also record the terrain altitude if possible
float terrain_altitude;
if (next_WP_loc.terrain_alt &&
terrain.height_above_terrain(terrain_altitude, true)) {
return terrain_altitude - target_alt;
}
#endif
2014-08-13 19:04:06 -03:00
return (adjusted_altitude_cm()*0.01f - ahrs.get_home().alt*0.01f) - target_alt;
}
/*
work out target altitude adjustment from terrain lookahead
*/
2015-05-13 03:09:36 -03:00
float Plane::lookahead_adjustment(void)
{
#if AP_TERRAIN_AVAILABLE
int32_t bearing_cd;
int16_t distance;
// work out distance and bearing to target
if (control_mode == &mode_fbwb) {
// there is no target waypoint in FBWB, so use yaw as an approximation
bearing_cd = ahrs.yaw_sensor;
distance = g.terrain_lookahead;
} else if (!reached_loiter_target()) {
bearing_cd = nav_controller->target_bearing_cd();
distance = constrain_float(auto_state.wp_distance, 0, g.terrain_lookahead);
} else {
// no lookahead when loitering
bearing_cd = 0;
distance = 0;
}
if (distance <= 0) {
// no lookahead
return 0;
}
float groundspeed = ahrs.groundspeed();
if (groundspeed < 1) {
// we're not moving
return 0;
}
// we need to know the climb ratio. We use 50% of the maximum
// climb rate so we are not constantly at 100% throttle and to
// give a bit more margin on terrain
float climb_ratio = 0.5f * SpdHgt_Controller->get_max_climbrate() / groundspeed;
if (climb_ratio <= 0) {
// lookahead makes no sense for negative climb rates
return 0;
}
// ask the terrain code for the lookahead altitude change
float lookahead = terrain.lookahead(bearing_cd*0.01f, distance, climb_ratio);
if (target_altitude.offset_cm < 0) {
// we are heading down to the waypoint, so we don't need to
// climb as much
lookahead += target_altitude.offset_cm*0.01f;
}
// constrain lookahead to a reasonable limit
return constrain_float(lookahead, 0, 1000.0f);
2014-08-08 00:54:05 -03:00
#else
return 0;
#endif
}
/*
correct target altitude using rangefinder data. Returns offset in
meters to correct target altitude. A positive number means we need
to ask the speed/height controller to fly higher
*/
2015-05-13 03:09:36 -03:00
float Plane::rangefinder_correction(void)
{
if (millis() - rangefinder_state.last_correction_time_ms > 5000) {
// we haven't had any rangefinder data for 5s - don't use it
return 0;
}
// for now we only support the rangefinder for landing
bool using_rangefinder = (g.rangefinder_landing && flight_stage == AP_Vehicle::FixedWing::FLIGHT_LAND);
if (!using_rangefinder) {
return 0;
}
return rangefinder_state.correction;
}
/*
correct rangefinder data for terrain height difference between
NAV_LAND point and current location
*/
void Plane::rangefinder_terrain_correction(float &height)
{
#if AP_TERRAIN_AVAILABLE
if (!g.rangefinder_landing ||
flight_stage != AP_Vehicle::FixedWing::FLIGHT_LAND ||
!terrain_enabled_in_current_mode()) {
return;
}
float terrain_amsl1, terrain_amsl2;
if (!terrain.height_amsl(current_loc, terrain_amsl1, false) ||
!terrain.height_amsl(next_WP_loc, terrain_amsl2, false)) {
return;
}
float correction = (terrain_amsl1 - terrain_amsl2);
height += correction;
auto_state.terrain_correction = correction;
#endif
}
/*
update the offset between rangefinder height and terrain height
*/
2015-05-13 03:09:36 -03:00
void Plane::rangefinder_height_update(void)
{
float distance = rangefinder.distance_cm_orient(ROTATION_PITCH_270)*0.01f;
if ((rangefinder.status_orient(ROTATION_PITCH_270) == RangeFinder::Status::Good) && ahrs.home_is_set()) {
if (!rangefinder_state.have_initial_reading) {
rangefinder_state.have_initial_reading = true;
rangefinder_state.initial_range = distance;
}
// correct the range for attitude (multiply by DCM.c.z, which
// is cos(roll)*cos(pitch))
rangefinder_state.height_estimate = distance * ahrs.get_rotation_body_to_ned().c.z;
rangefinder_terrain_correction(rangefinder_state.height_estimate);
// we consider ourselves to be fully in range when we have 10
// good samples (0.2s) that are different by 5% of the maximum
// range from the initial range we see. The 5% change is to
// catch Lidars that are giving a constant range, either due
// to misconfiguration or a faulty sensor
if (rangefinder_state.in_range_count < 10) {
if (!is_equal(distance, rangefinder_state.last_distance) &&
fabsf(rangefinder_state.initial_range - distance) > 0.05f * rangefinder.max_distance_cm_orient(ROTATION_PITCH_270)*0.01f) {
rangefinder_state.in_range_count++;
}
if (fabsf(rangefinder_state.last_distance - distance) > rangefinder.max_distance_cm_orient(ROTATION_PITCH_270)*0.01*0.2) {
// changes by more than 20% of full range will reset counter
rangefinder_state.in_range_count = 0;
}
} else {
rangefinder_state.in_range = true;
if (!rangefinder_state.in_use &&
(flight_stage == AP_Vehicle::FixedWing::FLIGHT_LAND ||
control_mode == &mode_qland ||
control_mode == &mode_qrtl ||
(control_mode == &mode_auto && quadplane.is_vtol_land(plane.mission.get_current_nav_cmd().id))) &&
g.rangefinder_landing) {
rangefinder_state.in_use = true;
gcs().send_text(MAV_SEVERITY_INFO, "Rangefinder engaged at %.2fm", (double)rangefinder_state.height_estimate);
}
}
rangefinder_state.last_distance = distance;
} else {
rangefinder_state.in_range_count = 0;
rangefinder_state.in_range = false;
}
if (rangefinder_state.in_range) {
// base correction is the difference between baro altitude and
// rangefinder estimate
float correction = relative_altitude - rangefinder_state.height_estimate;
#if AP_TERRAIN_AVAILABLE
// if we are terrain following then correction is based on terrain data
float terrain_altitude;
if ((target_altitude.terrain_following || terrain_enabled_in_current_mode()) &&
terrain.height_above_terrain(terrain_altitude, true)) {
correction = terrain_altitude - rangefinder_state.height_estimate;
}
#endif
// remember the last correction. Use a low pass filter unless
// the old data is more than 5 seconds old
uint32_t now = millis();
if (now - rangefinder_state.last_correction_time_ms > 5000) {
rangefinder_state.correction = correction;
rangefinder_state.initial_correction = correction;
if (g.rangefinder_landing) {
landing.set_initial_slope();
}
rangefinder_state.last_correction_time_ms = now;
} else {
rangefinder_state.correction = 0.8f*rangefinder_state.correction + 0.2f*correction;
rangefinder_state.last_correction_time_ms = now;
if (fabsf(rangefinder_state.correction - rangefinder_state.initial_correction) > 30) {
// the correction has changed by more than 30m, reset use of Lidar. We may have a bad lidar
if (rangefinder_state.in_use) {
gcs().send_text(MAV_SEVERITY_INFO, "Rangefinder disengaged at %.2fm", (double)rangefinder_state.height_estimate);
}
memset(&rangefinder_state, 0, sizeof(rangefinder_state));
}
}
}
}
/*
determine if Non Auto Terrain Disable is active and allowed in present control mode
*/
bool Plane::terrain_disabled()
{
return control_mode->allows_terrain_disable() && non_auto_terrain_disable;
}
/*
Check if terrain following is enabled for the current mode
*/
#if AP_TERRAIN_AVAILABLE
const Plane::TerrainLookupTable Plane::Terrain_lookup[] = {
{Mode::Number::FLY_BY_WIRE_B, terrain_bitmask::FLY_BY_WIRE_B},
{Mode::Number::CRUISE, terrain_bitmask::CRUISE},
{Mode::Number::AUTO, terrain_bitmask::AUTO},
{Mode::Number::RTL, terrain_bitmask::RTL},
{Mode::Number::AVOID_ADSB, terrain_bitmask::AVOID_ADSB},
{Mode::Number::GUIDED, terrain_bitmask::GUIDED},
{Mode::Number::LOITER, terrain_bitmask::LOITER},
{Mode::Number::CIRCLE, terrain_bitmask::CIRCLE},
{Mode::Number::QRTL, terrain_bitmask::QRTL},
{Mode::Number::QLAND, terrain_bitmask::QLAND},
{Mode::Number::QLOITER, terrain_bitmask::QLOITER},
};
bool Plane::terrain_enabled_in_current_mode() const
{
// Global enable
if ((g.terrain_follow.get() & int32_t(terrain_bitmask::ALL)) != 0) {
return true;
}
// Specific enable
for (const struct TerrainLookupTable entry : Terrain_lookup) {
if (entry.mode_num == control_mode->mode_number()) {
if ((g.terrain_follow.get() & int32_t(entry.bitmask)) != 0) {
return true;
}
break;
}
}
return false;
}
#endif