nxp/rt117x:Fix Pin IRQ
nxp/rt117x:Support 4 i2c busses
nxp/rt117x:Add px4io_serial support
nxp/imxrt:Expand ToneAlarmInterface to GPT 3 & 4
px4_fmu-6xrt:Using imxrt_flexspi_nor_octal
px4_fmu-6xrt:Entry is start
px4_fmu-6xrt:Add Proper MTD
px4_fmu-6xrt:Set I2C Buses
px4_fmu-6xrt:Proper SPI usage
px4_fmu-6xrt:Adjust memory Map to use the 2 MB
px4_fmu-6xrt:Bring in ROMAPI
px4_fmu-6xrt:Push FLASH to 200Mhz
px4_fmu-6xrt:Use BOARD_I2C_LATEINIT
px4_fmu-6xrt:Clock Config remove unused devices
px4_fmu-6xrt:Remove EVK SDRAM IO
px4_fmu-6xrt:Enable SE550 using HW_VER_REV_DRIVE
px4_fmu-6xrt:Use MTD to mount FRAM on Flex SPI
px4_fmu-6xrt:Manifest
px4_fmu-6xrt:Restore board_peripheral_reset
px4_fmu-6xrt:Set I2C buss Interna/Externa and startup
nxp/rt117x:Set 6 I2C busses
px4_fmu-6xrt:Correct Clock Sources and Freqency Settings
px4_fmu-6xrt:Correct ADC Settings
px4_fmu-6xrt:Tune FlexSPI config and sync header with debug variant Linker prep for rodata ahb partitioning
px4_fmu-6xrt:FlexSPI prefetch partition split .text and .rodata
Current config
1KB Prefetch .rodata
3KB Prefetch .text
px4_fmu-6xrt:Run imxrt_flash_setup_prefetch_partition from ram with barriers
px4_fmu-6xrt:Use All OCTL setting from FLASH g_flash_config SANS lookupTable
px4_fmu-6xrt:Octal spi boot/debug problem bypass
px4_fmu-6xrt:Add PWM test
px4_fmu-6xrt:Fix clockconfig and USB vbus sense
px4_fmu-6xrt: Use TCM
px4_fmu-6xrt: Ethernet bringup
imxrt: use unique_id register for board_identity
px4_fmu-6xrt: update ITCM mapping, todo proper trap on pc hitting 0x0
px4_fmu-6xrt:correct rotation icm42688p onboard imu
rt117x: Add SSARC HP RAM driver for memory dumps
px4_fmu-6xrt: Enable hardfault_log
px4_fmu-6xrt: Enable DMA pool
px4_fmu-6xrt: fix uart mapping
px4_fmu-6xrt: enable SocketCAN & DroneCAN
px4_fmu-6xrt:Command line history TAB completion
px4_fmu-6xrt:Fix pinning duplication
px4_fmu-6xrt:Support conditional PHY address based on selected PHY
px4_fmu-6xrt:Add Pull Downs on CTS, use GPIO for RTS
px4_fmu-6xrt:Set TelemN TX Slew rate and Drive Strenth to max
px4_fmu-6xrt::Set TELEM Buffers add HW HS
px4_fmu-6xrt:Turn off DMA poll
px4_fmu-6xrt:RC_SERIAL_PORT needed to be px4io to disable rc_input using TELEM2!
px4_fmu-6xrt: bootloader (#22228)
* imxrt:Add bootloader support
* bootloader:imxrt clear BOOT_RTC_SIGNATURE
* px4_fmu-6xrt:Add bootloader
* px4_fmu-6xrt:bootloader removed ADC
* px4_fmu-6xrt:bootloader base bootloader script off of script.ld
* px4_fmu-6xrt:add _bootdelay_signature & change entry from 0x30000000 to 0x30040000
* px4_fmu-6xrt:hw_config Bootloader has to have 12 bytes
px4_fmu-6xrt:Default to use LAN8742A PHY
px4_fmu-v6xrt:VID Set to Drone Code
board_reset:Enable ability to write RTC GP regs
px4_fmu-6xrt:Fix CMP0079 error
rt117x:micro_hal Add a PX4_MAKE_GPIO_PULLED_INPUT
px4_fmu-v6xrt:Set CTS High before VDD_5V applided to ports to avoid radios fro entering bootloaders
fmu-v6xrt: increase 5v down time
fmu-v6xrt:Ready for Release DEBUGASSERTS off and Console 57600,
Bootloder updated.
imxrt:board_hw_rev_ver Rework for 3.893V Ref
px4_fmu-v6xrt:Move ADC to Port3
PX4_SIM model need the simulator (gz_) prefix
Fix post debug task
Add x500_depth, rc_cessna, standard_vtol
Signed-off-by: Beniamino Pozzan <beniamino.pozzan@phd.unipd.it>
- use `gazebo-classic` everywhere consistently referring to the original Gazebo (eg version 9,10,11)
- additional `gazebo_*` helper targets added for compatibility, but warn about deprecation and tell you the new target naming
- use `gz` everywhere when referring to Gazebo (aka Ignition Gazebo or new Gazebo)
- new ROS2 platform in PX4 intended for creating configs that build and run entirely in ROS2
- PX4_CONFIG defaults to px4_ros2_default if no config specified and in a colcon workspace with ROS_VERSION=2
- currently doesn't do much other than allow you to build px4 msgs interface package
- update all msgs to be directly compatible with ROS2
- microdds_client improvements
- timesync
- reduced code size
- add to most default builds if we can afford it
- lots of other little changes
- purge fastrtps (I tried to save this multiple times, but kept hitting roadblocks)
- for convenience merge px4_sitl_ign into px4_sitl_default, but allow simulator_ignition_bridge to quietly skip inclusion if ignition-transport isn't available
- simulator_ignition_bridge only try setting the system clock in
lockstep builds
- this simplifies usage and CI system dependencies
- new modules/simulation directory to collect all simulators and related modules
- new Tools/simulation directory to collect and organize scattered simulation submodules, scripts, etc
- simulation module renamed to simulator_mavlink
- sih renamed to simulator_sih (not a great name, but I wanted to be clear it was a simulator)
- ignition_simulator renamed to simulator_ignition_bridge
- large sitl_target.cmake split by simulation option and in some cases pushed to appropriate modules
- sitl targets broken down to what's actually available (eg jmavsim only has 1 model and 1 world)
- new Gazebo consistently referred to as Ignition for now (probably the least confusing thing until we fully drop Gazebo classic support someday)
- much simpler direct interface using Ignition Transport
- in tree models and worlds
- control allocation output configuration, no more magic actuator mapping to mavlink and back
- currently requires no custom Gazebo plugins (keeping things as lightweight and simple as possible)
Co-authored-by: Jaeyoung-Lim <jalim@ethz.ch>
- cmake NuttX build wrapper compile in place instead of copying source tree to build directory
- slightly faster skipping necessary copying (depending on system)
- allows debugging in place
- easier to work directly in NuttX following official documentation
- simplifies overall build which should make it easier to resolve any remaining NuttX dependency issues in the build system
- the downside is switching back and forth between different builds always require rebuilding NuttX, but I think this is worth the improved developer experience
- also no longer builds px4io and bootloader in every single build, for most users these rarely change and we're wasting a lot of build time
- include icm20948 on most boards by default
- create more test variants for default boards near flash limit (cuav_nora_test, cuav_x7pro_test, holybro_durandal-v1_test)
in workspace settings. This comes down to user preference
and there's no particular reason to change this based on the workspace.
I found it confusing to have this non-default behavior
just for PX4 editing.
Alex Klimaj
Bryce Melander
Bryce Clark
David Sidrane
Daniel Agar
Beniamino Pozzan
Christian Rauch
Robbie Drage
Peter van der Perk
Benjamin Perseghetti
Travis Bottalico
David Lechner
dirksavage88
Viktor Vladic
Vatsal Asitkumar Joshi
benjinne
Matthias Grob
modaltb
Lorenz Meier