mirror of https://github.com/ArduPilot/ardupilot
208 lines
4.3 KiB
Plaintext
208 lines
4.3 KiB
Plaintext
|
|
# hw definition file for processing by chibios_hwdef.py
|
|
# for MindPX-v2 hardware
|
|
|
|
# MCU class and specific type
|
|
MCU STM32F4xx STM32F427xx
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 88
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 8000000
|
|
|
|
STM32_ST_USE_TIMER 5
|
|
|
|
|
|
# flash size
|
|
FLASH_SIZE_KB 2048
|
|
|
|
# space to reserve for bootloader and storage at start of flash
|
|
FLASH_RESERVE_START_KB 16
|
|
|
|
# space to reserve for storage at end of flash
|
|
FLASH_RESERVE_END_KB 0
|
|
|
|
# serial port for stdout disabled, uses USB instead
|
|
# STDOUT_SERIAL SD7
|
|
# STDOUT_BAUDRATE 57600
|
|
|
|
# order of I2C buses
|
|
I2C_ORDER I2C1 I2C2
|
|
|
|
# order of UARTs (and USB)
|
|
SERIAL_ORDER OTG1 USART2 USART3 UART4 UART8 USART1 UART7 USART6
|
|
|
|
# UART4 is GPS
|
|
PA0 UART4_TX UART4
|
|
PA1 UART4_RX UART4
|
|
PA4 VDD_5V_SENS ADC1 SCALE(2)
|
|
|
|
# SPI1 is fram bus
|
|
PA5 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
|
|
# Timers 1-4 are used for (servo) PWM outputs and 5/6 are used for clocks
|
|
# Use Timer 14 for tone generation
|
|
PA7 TIM14_CH1 TIM14 GPIO(32) ALARM
|
|
|
|
PA8 RUN_LED OUTPUT GPIO(0)
|
|
PA9 VBUS INPUT
|
|
PA10 SBUS_INV OUTPUT
|
|
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
|
|
# PWM outputs
|
|
PE9 TIM1_CH1 TIM1 PWM(1)
|
|
PE11 TIM1_CH2 TIM1 PWM(2)
|
|
PE13 TIM1_CH3 TIM1 PWM(3)
|
|
PE14 TIM1_CH4 TIM1 PWM(4)
|
|
|
|
PD12 TIM4_CH1 TIM4 PWM(5)
|
|
PD13 TIM4_CH2 TIM4 PWM(6)
|
|
PD14 TIM4_CH3 TIM4 PWM(7)
|
|
PD15 TIM4_CH4 TIM4 PWM(8)
|
|
|
|
PB4 TIM3_CH1 TIM3 PWM(9) GPIO(50)
|
|
PC7 TIM3_CH2 TIM3 PWM(10) GPIO(51)
|
|
PB0 TIM3_CH3 TIM3 PWM(11) GPIO(52)
|
|
PB1 TIM3_CH4 TIM3 PWM(12) GPIO(53)
|
|
|
|
PA15 TIM2_CH1 TIM2 PWM(13) GPIO(54)
|
|
PB3 TIM2_CH2 TIM2 PWM(14) GPIO(55)
|
|
PA2 TIM2_CH3 TIM2 PWM(15)
|
|
PA3 TIM2_CH4 TIM2 PWM(16)
|
|
|
|
PB2 GYRO_CS CS
|
|
|
|
PB5 SPI1_MOSI SPI1
|
|
|
|
# USART1 is SBUS
|
|
PB6 USART1_TX USART1
|
|
PB7 USART1_RX USART1
|
|
|
|
# I2C1 is mag I2C
|
|
PB8 I2C1_SCL I2C1
|
|
PB9 I2C1_SDA I2C1
|
|
|
|
# I2C2 is FMU I2C
|
|
PB10 I2C2_SCL I2C2
|
|
PB11 I2C2_SDA I2C2
|
|
|
|
# SPI2 is external SPI (radio NRF)
|
|
PB13 SPI2_SCK SPI2
|
|
PB14 SPI2_MISO SPI2
|
|
PB15 SPI2_MOSI SPI2
|
|
|
|
PC0 BAT_CURR_SENS ADC1
|
|
PC1 FMU_GPIO3 INPUT # RSSI
|
|
PC2 BAT_VOLT_SENS ADC1
|
|
PC3 FMU_ADC1 ADC1
|
|
PC4 FMU_ADC2 ADC1
|
|
PC5 FMU_ADC3 ADC1
|
|
|
|
# RC input default to timer
|
|
PC6 TIM8_CH1 TIM8 RCININT PULLDOWN
|
|
|
|
# alternative RC input using USART6
|
|
PC6 USART6_TX USART6 NODMA ALT(1)
|
|
|
|
PC8 SDIO_D0 SDIO
|
|
PC9 SDIO_D1 SDIO
|
|
PC10 SDIO_D2 SDIO
|
|
PC11 SDIO_D3 SDIO
|
|
PC12 SDIO_CK SDIO
|
|
|
|
PC13 ACCEL_DRDY INPUT
|
|
PC14 MAG_DRDY INPUT
|
|
PC15 BARO_CS CS
|
|
|
|
PD0 CAN1_RX CAN1
|
|
PD1 CAN1_TX CAN1
|
|
PD2 SDIO_CMD SDIO
|
|
|
|
# USART2 serial2 telem1
|
|
PD3 USART2_CTS USART2
|
|
PD4 USART2_RTS USART2
|
|
PD5 USART2_TX USART2
|
|
PD6 USART2_RX USART2
|
|
PD7 NRF_CSN INPUT
|
|
|
|
# USART3 serial3 telem2
|
|
PD8 USART3_TX USART3
|
|
PD9 USART3_RX USART3
|
|
PD10 NRF_INT INPUT
|
|
PD11 ACCEL_MAG_CS CS
|
|
|
|
|
|
# UART8 is FrSky
|
|
PE0 UART8_RX UART8
|
|
PE1 UART8_TX UART8
|
|
|
|
# allow this uart to be inverted for transmit under user control
|
|
# the polarity is the value to use on the GPIO to change the polarity
|
|
# to the opposite of the default
|
|
PB12 UART8_TXINV OUTPUT HIGH GPIO(78) POL(0)
|
|
|
|
# SPI4 is M_SPI (main sensors)
|
|
PE2 SPI4_SCK SPI4
|
|
PE3 MPU_CS CS
|
|
PE4 GYRO_DRDY INPUT
|
|
PE5 SPI4_MISO SPI4
|
|
PE6 SPI4_MOSI SPI4
|
|
|
|
# UART7 is debug
|
|
PE7 UART7_RX UART7
|
|
PE8 UART7_TX UART7
|
|
|
|
PE10 MPU_DRDY INPUT
|
|
PE12 FRAM_CS CS
|
|
PE15 NRF_CS CS
|
|
|
|
# SPI device table
|
|
SPIDEV ms5611 SPI4 DEVID1 BARO_CS MODE3 2*MHZ 2*MHZ
|
|
SPIDEV mpu6500 SPI4 DEVID2 MPU_CS MODE3 500*KHZ 4*MHZ
|
|
SPIDEV lsm9ds0_am SPI4 DEVID3 ACCEL_MAG_CS MODE3 11*MHZ 11*MHZ
|
|
SPIDEV lsm9ds0_g SPI4 DEVID4 GYRO_CS MODE3 11*MHZ 11*MHZ
|
|
SPIDEV ramtron SPI1 DEVID5 FRAM_CS MODE3 8*MHZ 8*MHZ
|
|
SPIDEV radio SPI2 DEVID6 NRF_CS MODE3 2*MHZ 2*MHZ
|
|
|
|
# two IMUs
|
|
IMU Invensense SPI:mpu6500 ROTATION_NONE
|
|
IMU LSM9DS0 SPI:lsm9ds0_g SPI:lsm9ds0_am ROTATION_YAW_90 ROTATION_YAW_90 ROTATION_YAW_90
|
|
|
|
# one baro
|
|
BARO MS56XX SPI:ms5611
|
|
|
|
# two compasses
|
|
COMPASS HMC5843 I2C:0:0x1e false ROTATION_YAW_90
|
|
COMPASS LSM303D SPI:lsm9ds0_am ROTATION_PITCH_180_YAW_270
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
|
|
define HAL_CHIBIOS_ARCH_MINDPXV2 1
|
|
|
|
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
|
|
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"
|
|
|
|
define HAL_STORAGE_SIZE 16384
|
|
|
|
# enable RAMTROM parameter storage
|
|
define HAL_WITH_RAMTRON 1
|
|
|
|
# allow to have have a dedicated safety switch pin
|
|
define HAL_HAVE_SAFETY_SWITCH 1
|
|
|
|
# enable FAT filesystem
|
|
define HAL_OS_FATFS_IO 1
|
|
|
|
# battery setup
|
|
define HAL_BATT_VOLT_PIN 12
|
|
define HAL_BATT_CURR_PIN 10
|
|
define HAL_BATT_VOLT_SCALE 10.1
|
|
define HAL_BATT_CURR_SCALE 17.0
|