cc0b2ab3bb
The Diatone Mamba MK4 H743 v2 Flight Control have moved from the DPS280 barometer to using SPL06. https://www.diatone.us/products/mamba-mk4-h743-v2-flight-control-30mm-m3l |
||
|---|---|---|
| .. | ||
| MambaH743v4_Board.jpg | ||
| README.md | ||
| defaults.parm | ||
| hwdef-bl.dat | ||
| hwdef.dat | ||
README.md
MambaH743v4 Flight Controller
The MambaH743v4 is a flight controller produced by Diatone.
Features
- MCU - STM32H743 32-bit processor running at 480 MHz
- IMU - Dual MPU6000 (Version A) or BMI270 (Version B) or Dual ICM42688 (v2)
- Barometer - DPS280
- OSD - AT7456E
- Onboard Flash: 1GBit
- 8x UARTs
- 9x PWM Outputs (8 Motor Output, 1 LED)
- Battery input voltage: 2S-6S
- BEC 3.3V 0.5A
- BEC 5V 3A
- BEC 5V 3A
- BEC 9V 3A
Pinout
UART Mapping
The UARTs are marked Rn and Tn in the above pinouts. The Rn pin is the receive pin for UARTn. The Tn pin is the transmit pin for UARTn.
- SERIAL0 -> USB
- SERIAL1 -> UART1 (RX/SBUS, DMA-enabled)
- SERIAL2 -> UART2
- SERIAL3 -> UART3
- SERIAL4 -> UART4 (GPS, DMA-enabled)
- SERIAL5 -> UART5 (SPort)
- SERIAL6 -> UART6 (ESC Telemetry)
- SERIAL7 -> UART7 (GPS, DMA-enabled)
RC Input
RC input is configured on the R1 (UART1_RX) pin. It supports all serial RC protocols. For protocols requiring half-duplex serial to transmit telemetry (such as FPort) you should setup SERIAL6 as an RC input serial port, with half-duplex, pin-swap and inversion enabled.
FrSky Telemetry
FrSky Telemetry is supported using the T5 pin (UART5 transmit). You need to set the following parameters to enable support for FrSky S.PORT
- SERIAL5_PROTOCOL 10
- SERIAL5_OPTIONS 7
OSD Support
The MambaH743v4 supports OSD using OSD_TYPE 1 (MAX7456 driver).
PWM Output
The MambaH743v4 supports up to 9 PWM outputs. The pads for motor output M1 to M8 are provided on both the motor connectors and on separate pads, plus M9 on a separate pad for LED strip or another PWM output.
The PWM is in 4 groups:
- PWM 1-4 in group1
- PWM 5,6 in group2
- PWM 7,8 in group3
- PWM 9 in group4
Channels within the same group need to use the same output rate. If any channel in a group uses DShot then all channels in the group need to use DShot. Channels 1-8 support bi-directional dshot.
Battery Monitoring
The board has a builting voltage and current sensor. The current sensor can read up to 130 Amps. The voltage sensor can handle up to 6S LiPo batteries.
The correct battery setting parameters are:
- BATT_MONITOR 4
- BATT_VOLT_PIN 11
- BATT_CURR_PIN 13
- BATT_VOLT_MULT 11.1
- BATT_AMP_PERVLT 64
Compass
The MambaH743v4 does not have a builtin compass, but you can attach an external compass using I2C on the SDA and SCL pads.
Loading Firmware
Initial firmware load can be done with DFU by plugging in USB with the bootloader button pressed. Then you should load the "with_bl.hex" firmware, using your favourite DFU loading tool.
Once the initial firmware is loaded you can update the firmware using any ArduPilot ground station software. Updates should be done with the *.apj firmware files.