mirror of https://github.com/ArduPilot/ardupilot
74 lines
2.2 KiB
Markdown
74 lines
2.2 KiB
Markdown
# SITL-on-HW notes
|
|
|
|
## Compiling and flashing
|
|
|
|
Run the sitl-on-hw.sh script to compile and flash for MatekH743. Adjust for your own board if required before running. This script will configure a build ready for running SITL-on-hardware and attempt to upload it to a connected board. It includes a set of embedded parameters to configure the simulated sensors appropriately.
|
|
|
|
::
|
|
|
|
cd $HOME/ardupilot
|
|
./libraries/SITL/examples/on-hardware/sitl-on-hw.sh
|
|
|
|
Plane can also be simulated:
|
|
|
|
::
|
|
|
|
cd $HOME/ardupilot
|
|
./libraries/SITL/examples/on-hardware/sitl-on-hw.sh -v plane
|
|
|
|
## Configuring
|
|
|
|
Wipe the parameters on the board; this can be done with a mavlink command, or by setting the FORMAT_VERSION parameter to 0.
|
|
|
|
For example:
|
|
|
|
::
|
|
|
|
STABILIZE> wipe_parameters IREALLYMEAANIT
|
|
STABILIZE> Got COMMAND_ACK: PREFLIGHT_STORAGE: ACCEPTED
|
|
AP: All parameters reset, reboot board
|
|
reboot
|
|
|
|
You may need to power-cycle the board at this point.
|
|
|
|
::
|
|
|
|
Device /dev/serial/by-id/usb-ArduPilot_MatekH743_3A0019001051393036353035-if00 reopened OK
|
|
link 1 OK
|
|
heartbeat OK
|
|
disabling flow control on serial 2
|
|
AP: Calibrating barometer
|
|
AP: Barometer 1 calibration complete
|
|
AP: Barometer 2 calibration complete
|
|
Init Gyro**
|
|
AP: ArduPilot Ready
|
|
Suggested EK3_BCOEF_* = 16.288, EK3_MCOEF = 0.208
|
|
Home: -35.36326 149.1652 alt=584.0000m hdg=353.0000
|
|
Smoothing reset at 0.001
|
|
AP: RCOut: PWM:1-13
|
|
AP: GPS 1: detected as SITL at 115200 baud
|
|
Time has wrapped
|
|
Time has wrapped 5577 368458
|
|
AP: EKF3 IMU0 initialised
|
|
AP: EKF3 IMU1 initialised
|
|
AP: EKF3 IMU0 tilt alignment complete
|
|
AP: EKF3 IMU1 tilt alignment complete
|
|
AP: EKF3 IMU1 MAG0 initial yaw alignment complete
|
|
AP: EKF3 IMU0 MAG0 initial yaw alignment complete
|
|
AP: PERF: 0/3999 [2653:2349] F=400Hz sd=39 Ex=0
|
|
AP: EKF3 IMU1 forced reset
|
|
AP: EKF3 IMU1 initialised
|
|
AP: EKF3 IMU0 forced reset
|
|
AP: EKF3 IMU0 initialised
|
|
AP: EKF3 IMU1 tilt alignment complete
|
|
AP: EKF3 IMU0 tilt alignment complete
|
|
AP: EKF3 IMU1 MAG0 initial yaw alignment complete
|
|
AP: EKF3 IMU0 MAG0 initial yaw alignment complete
|
|
AP: PreArm: 3D Accel calibration needed
|
|
AP: PERF: 0/4000 [2631:2369] F=400Hz sd=5 Ex=0
|
|
AP: EKF3 IMU0 origin set
|
|
AP: EKF3 IMU1 origin set
|
|
AP: PERF: 0/4000 [2639:2362] F=400Hz sd=7 Ex=0
|
|
|
|
Force
|